BMP estimation of landfilled municipal solid waste by multivariate statistical methods using specific waste parameters: case study of a sanitary landfill in Turkey

The main objective of this study was to determine whether methane potential of waste could be estimated more easily by a limited number of waste characterization variables. 36 samples were collected from 12 locations and 3 waste depths in order to represent almost all waste ages at the landfill. Actual remaining methane potential of all samples was determined by the biochemical methane potential (BMP) tests. The cumulative methane production of closed landfill (cLF) samples reached 75–125 mL at the end of experiment duration, while the samples from active landfill (aLF) produced in average 216–266 mL methane. The average experimental k and L ₀ values of cLF and aLF were determined by non-linear regression using BMP data with first-order kinetic equation as 0.0269 day^?1–30.38 mL/g dry MSW and 0.0125 day^?1–102.1 mL/g dry MSW, respectively. The principal component analysis (PCA) was applied to analyze the results for cLF and aLF along with BMP results. Three PCs for the data set were extracted explaining 72.34 % variability. The best MLR model for BMP prediction was determined for seven variables (pH–Cl–TKN–NH4–TOC–LOI–Ca). R ² and Adj. R ² values of this best model were determined as 80.4 and 75.3 %, respectively.     

Adsorption of Crystal Violet Dye from Aqueous Solution by Poly(Acrylamide-<Emphasis Type="Italic">co</Emphasis>-Maleic Acid)/Montmorillonite Nanocomposite

Poly(acrylamide-co-maleic acid)/montmorillonite nanocomposites, were synthesized via in situ polymerization with different maleic acid and MMT content. The capability of the hydrogel for adsorption of crystal violet (CV) was investigated in aqueous solutions at different pH values and temperatures. The pseudo-second-order kinetics model could fit successfully the adsorption kinetic data. The effects of maleic acid to acrylamide molar ratio (MA_R), weight percent of MMT (MMT%), the pH of medium and the solution temperature (T) on the CV adsorption capacity (q _e ) of adsorbents were studied by Taguchi experimental design approach. The results indicated that increasing the MMT% leads to a greater q _e . The q _e value of adsorbents increased also with increasing both MA_R and pH, while reduced when the temperature of medium increased. The relatively optimum conditions to achieve a maximum CV adsorption capacity for P(AAm/MA)/MMT adsorbents were found as: 0.06 for MA_R and 5 % of MMT%, medium pH = 7 and T = 20 °C.     

Enhancement of biogas production potential from <Emphasis Type="Italic">Acacia</Emphasis> leaf waste using alkaline pre-treatment and co-digestion

The objective of this research was to evaluate possibility of utilizing Acacia leaves (A. mangium and A. auriculiformis), which is an agro-industrial waste from the pulp and paper industry. The effects of alkaline pre-treatment and co-digestion with Napier grass for the enhancement of biogas production from Acacia leaf waste (ALW) were investigated. Six continuous stirred tank reactors with a working volume of 5 L were carried out at the laboratory scale. The results showed that pre-treatment of Acacia leaf waste (pretreated ALW) by soaking in 3 % NaOH for 48 h increased the biogas and methane productivity to 0.200 and 0.117 m³/kgVS_added compared to 0.098 and 0.048 m³/kgVS_added of raw ALW digestion, respectively. Meanwhile, the co-digestion of Acacia leaves with different proportions of Napier grass at ratios of 1:1–1:3 in volatile solid basis also increased the production of biogas and its productivity. The maximum gas production yields of 0.424 and 0.268 m³/kgVS_added for biogas and methane were obtained at 1:3 ratio. This finding affirms the potential of ALW and its possibility to use as biogas feedstock in both single and co-substrate with Napier grass.     

Water Absorption Kinetics and Hygrothermal Aging of Poly(lactic acid) Containing Halloysite Nanoclay and Maleated Rubber

Poly(lactic acid)/halloysite nanoclay composites (PLA/HNC) containing maleic anhydride grafted styrene-ethylene/butylene-styrene (SEBS-g-MAH) were produced using melt compounding followed by compression molding. The effects of hygrothermal aging on the thermal properties and functional groups changes of the HNC reinforced PLA (with and without SEBS-g-MAH) at three different temperatures (i.e., 30, 40 and 50 °C) were analyzed using differential scanning calorimetry and Fourier transform infrared spectroscopy techniques. The diffusion coefficient (D) of PLA was decreased by the incorporation of HNC and SEBS-g-MAH. The activation energy of water diffusion (E _a ) of PLA/HNC/SEBS-g-MAH nanocomposites was higher than that of pure PLA. The glass transition temperature (T _g ), cold-crystallization temperature (T _cc ) and melting temperature (T _m ) of the PLA sample were shifted to lower temperature and the effect was more pronounced at 50 °C. The carbonyl index values of all PLA samples increased after immersed in 40 and 50 °C, which is due to the formation of higher amount of carboxyl groups during the hydrolysis process.     

Kinetic Analysis of the Temperature Effect on Polyhydroxyalkanoate Production by <Emphasis Type="Italic">Haloferax mediterranei</Emphasis> in Synthetic Molasses Wastewater

Haloferax mediterranei is an extremely halophilic archaeon that is able to synthesize polyhydroxyalkanoate (PHA) in high salt environment with low sterility demand. In this study, a mathematical model was validated and calibrated for describing the kinetic behavior of H. mediterranei at 15, 20, 25, and 35 °C in synthetic molasses wastewater. Results showed that the production of PHA by H. mediterranei, ranging from 390 to 620 mg h^?1 L^?1, was strongly dependent on the temperature. The specific growth rate (µ _max), specific substrate utilization rate (q _max), and specific decay rate (k _d) of H. mediterranei increased with temperature following Arrhenius equation prediction. The estimated activation energy was 58.31, 25.59, and 22.38 kJ mol^?1 for the process of cell growth, substrate utilization, and cell decay of H. mediterranei, respectively. The high temperature triggered the increased PHA storage even without nitrogen limitation. Thus, working at high temperatures seems a good strategy for improving the PHA productivity of H. mediterranei.     

Comparison of three ornamental plants for phytoextraction potential of chromium removal from tannery sludge

Based on pre-experimentation, three ornamental plants, Mirabilis jalapa, Impatiens Balsamin (I. Balsamin) and Tagetes erecta L., were selected as target plants to study the phytoextraction of chromium (Cr) in tannery sludge irrigated with four treatments according to Cr concentration gradient [Control (CK); 20.50 × 10³ mg kg^?1 (T1); 51.25 × 10³ mg kg^?1 (T2); 102.50 × 10³ mg kg^?1 (T3)]. Results of pot experiments showed that the biomass of Mirabilis jalapa and Tagetes erecta L. had no significant differences among the four treatments, while I. Balsamin showed a decline trend in the biomass with the increase of Cr concentration, probably due to some extent to the poisoning effect of Cr under treatment T2 or T3. Mirabilis jalapa accumulated Cr concentration, with 408.97, 124.97, 630.16 and 57.30 mg kg^?1 in its roots, stems, leaves and inflorescence, respectively. The translocation factor and the bioaccumulation coefficient of Mirabilis jalapa are each greater than 1, indicating that Mirabilis jalapa has the strong ability to tolerate and enrich Cr by biological processes. Comparing accumulation properties of the three ornamental plants, in the amount and allocation, Mirabilis jalapa showed the highest phytoextraction efficiency and could grow well at the high Cr concentration. Our experiments suggest that Mirabilis jalapa is the expected flower species for Cr removal from tannery sludge.     

Preparation and Characterization of Polyaniline and Ag/ Polyaniline Composite Nanoporous Particles and Their Antimicrobial Activities

Polyaniline (PANI) and Ag/PANI nanoporous composite were prepared by an oxidative polymerization method. The oxidation process of PANI nanoparticles was occurred using (NH₄)₂S₂O₈ while the oxidation process of Ag/PANI nanoporous composite was occurred using AgNO₃ under the effect of artificial radiation. The structural, morphological, and optical properties of the PANI and Ag/PANI nanoporous structures were studied using different characterization tools. The results confirm the formation of polycrystalline nanoporous PANI and spherical nanoporous composite of Ag/PANI particles. Antibacterial activity tests against gram-positive bacteria, Bacillus subtilis and Staphylococcus aureus, and gram-negative bacteria, Escherichia coli, and Salmonella species were carried out using different concentrations of PANI nanoparticles and Ag/PANI nanoporous composites. PANI has not antibacterial effect against all studied pathogens. In contrast, Ag/PANI nanoporous composites possessed antibacterial activity that is identified by the zone of inhibition. The inhibition zones of bacteria are in order; Salmonella species?>?S. aureus?>?B. subtilis?>?E. coli. The inhibition zones of all bacteria increased with increasing concentrations of Ag/PANI nanoporous composites from 200 to 400 ppm then decreased with further increasing of the dose concentrations to 600 ppm. Finally, a simplified mechanism based on the electrostatic attraction is presented to describe the antimicrobial activity of Ag/PANI nanoporous composite.     

Selective Lead(II) Adsorption and Flocculation Characteristics of the Grafted Sodium Alginate: A Comparative Study

Synthesis of sodium alginate-g-poly(acrylamide-co-N-methylacrylamide) [S-III], sodium alginate-g-poly(N-methylacrylamide-co-N,N-dimethylacrylamide) [S-II], sodium alginate-g-poly(acrylamide-co-N,N-dimethylacrylamide) [S-I]. Sodium alginate-g-poly(N,N-dimethylacrylamide) [SAG-g-PDMA] and sodium alginate-g-poly(acrylamide) [SAG-g-PAM] were prepared by solution polymerization technique using potassium peroxydisulfate as the initiator at 70?°C in water medium. The graft copolymers were characterized by FTIR and NMR (¹H and ¹³C) spectroscopy, SEM and XRD studies. All the five graft copolymers were used to remove Pb(II) ions from the aqueous solution and also in flocculation studies of kaolin clay (1.0 wt%), silica (1.0 wt%) and iron ore slime (0.25 wt%) suspensions. A comparative studies of all the five graft copolymers were also made in both the two cases. The Pb(II) ion removal capacity of all the graft copolymers follows the order S-III?>?SAG-g-PAM?>?S-II?>?SAG-g-PDMA?>?S-I. But the flocculation performance of the graft copolymers follows the order S-II?>?S-I?>?S-III?>?SAG-g-PDMA?>?SAG-g-PAM. S-III was also used for the competitive metal ion removal with Hg(II), Cd(II), Cu(II) and Zn(II). Pb(II) adsorption of S-III (the best Pb(II) ion adsorber) follows pseudo second order rate equation and Langmuir adsorption isotherm.     

Solubility parameters for determining optimal solvents for separating PVC from PVC-coated PET fibers

Poly(vinyl chloride) (PVC) in PVC-coated poly(ethylene terephthalate) (PET) fabrics can be separated through dissolution in a suitable solvent, leaving only the PET fibers. We investigated the solubility of PVC in 30 solvents using swelling tests. The results were compared with those obtained using the Hansen, Gutmann, Swain, E _T(30), and Kamlet–Taft parameters. For this purpose, Gaussian plots of the PVC swellability versus solubility parameter were used to decide the applicability of the solubility parameter system. Only Gutmann’s electron acceptor–donor parameter (AN + DN) and the Kamlet–Taft parameters β and π* could describe the PVC-solvent system satisfactorily. Tetrahydrofuran (THF), methyl ethyl ketone (MEK), N,N-dimethylformamide (DMF), cyclohexanone, and cyclopentanone were tested for separating PVC from PET at different temperatures. THF dissolved PVC at 20 °C, while cyclohexanone and cyclopentanone did so at 40 °C. Traces of PVC remained on the PET fibers when DMF was used. Complete dissolution of PVC was not achieved at any temperature with MEK. The present work shows that solubility parameters are a helpful tool for the search for suitable solvents. It shows also that solubility parameters have to be selected carefully, since their usefulness depends strongly on the polymer properties.     

Accelerated Stability Testing of a Polyherbal Transdermal Patches Using Polyvinyl Alcohol and Hydroxypropyl Methylcellulose as a Controlling Polymer Layer

The present work was to evaluate the stability potential of (E)-4-(3,4-dimethoxyphenyl)but-3-en-l-ol (Compound D) in polyherbal transdermal patches. The polyherbal formulation composed of the rhizomes of Zingiber cassumunar and Curcuma longa, leaves and stems of Cymbopogon citratus, rind and leaves of Citrus hystrix fruit, and leaves of Acacia rugata and Tamarindus indica. Polyvinyl alcohol and hydroxypropyl methylcellulose were used as a matrix film, and glycerine was used as a plasticizer. Stability testing was established for 6 months under accelerated conditions as according to International Conference on Harmonisation guidelines. Mechanical properties, moisture uptake, swelling ratio, and in vitro studies were evaluated. New Zealand white rabbits were used as the animal model. Results obtained after 6 months showed that the polyherbal transdermal patches were stable, with a good mechanical properties and hydrophilicity. In vitro study kinetics for active Compound D fitted to the Higuchi model for both release and skin permeation. The transdermal patch containing polyherbal formulation was safe to apply on the skin without irritation. Thus, transdermal patches containing this polyherbal formulation had good stability potential, with no irritation on application.     

Adsorptive Removal of Malachite Green Chloride and Reactive Red-198 from Aqueous Solutions by Using Multiwall Carbon Nanotubes-Graft-Poly (2-acrylamido-2-methyl-1-propanesulfonic acid)

The multiwall carbon nanotubes (MWCNTs) were modified by 2-acrylamido-2-methyl-1-propanesulfonic acid (AMPS) via grafting reaction and γ-rays of ⁶⁰Co source was used as initiator. The outcome product was called hydroxyethylated (HOEt-MWCNTs) graft poly(AMPS) and abbreviated as HOEt-MWCNTs-g-PAMPS. The parameters that affected the grafting yield were optimized. The maximum grafting obtained was ~20 %. HOEt-MWCNTs-g-PAMPS were characterized by Fourier transform infra red, scanning electron microscopy, high resolution transmission electron microscopy, thermal gravimetric analysis. The adsorptive removals of malachite green chloride (MGC) and reactive red 198 (RR-198) onto HOEt-MWCNTs-g-PAMPS were studied at variable conditions. The adsorption isotherms were analyzed using Langmuir, Redlich–Peterson, Freundlich, Khan and Sips models. The results referred that Sips model is the best fitting to adsorption of MGC and Freundlich model is the best fitting to RR-198 adsorption. The monolayer coverage capacities of HOEt-MWCNTs-g-PAMPS for MGC and RR-198 dyes were found 172 and 323 mg g^?1, respectively. The rate of kinetic adsorption processes of MGC and RR-198 onto HOEt-MWCNTs-g-PAMPS were described by using pseudo-first order, pseudo-second order and intraparticle diffusion models. The pseudo-first order and pseudo-second order models were the best choice among the kinetic models to depict the adsorption behaviors of MGC and RR-198 dyes onto HOEt-MWCNTs-g-PAMPS, respectively. Further, the effect of temperature on the adsorption isotherms was investigated and the thermodynamic parameters were obtained. The results indicated that the adsorption process is spontaneous and endothermic. The values of ΔG° varied in range with the mean values showing a gradual increase from ?3.17 to ?3.64 kJ mol^?1 for MGC and ?3.36 to ?3.73 kJ mol^?1 for RR-198. The reusability and regeneration of adsorbent were investigated. The outcome data referred to that the efficiency of adsorbent >98 %. The outline results declared that there is a good potentiality for the HOEt-MWCNTs-g-PAMPS to be used as an adsorbent for the removal of MGC and RR-198 from aqueous solutions.     

Experimental Investigation of Cellulose/Silver Nanocomposites Using In Situ Generation Method

Cellulose gel films were prepared by regeneration process using pre-cooled aq.(8 wt% LiOH + 15 wt% urea) mixture as solvent and ethyl alcohol as non solvent. The Terminus cattapa leaf extract diffused wet cellulose films were then dipped in 1–5 mM aq.AgNO₃ solutions to allow in situ generation of silver nanoparticles (AgNPs). Besides the in situ generation, some AgNPs were also formed outside the wet films in the solution. The AgNPs formed outside the films were observed under transmission electron microscope and scanning electron microscope. The nanocomposite films were also characterized by Fourier transform infrared spectroscopy, X-ray diffraction and thermogravimetric analysis and tensile test. The thermal stability of the composite films was lower than that of the matrix up to a temperature of ~300 °C and afterwards showed a reverse trend. The tensile strength of the nanocomposite films was found to be higher than the matrix but decreased with increasing concentration of aq.AgNO₃. The cellulose/AgNPs composite films showed good antibacterial activity against E. coli (gram positive) and Bacillus sp. (gram negative). Based on the aforementioned properties, the cellulose/AgNPs composite films can be considered for antibacterial packaging and medical applications.     

Enzyme-Assisted Extraction and Pb<Superscript>2+</Superscript> Biosorption of Polysaccharide from <Emphasis Type="Italic">Cordyceps militaris</Emphasis>

The enzyme assisted extraction conditions of polysaccharide from Cordyceps militaris mycelia were firstly investigated by kinetics analysis and the optimal operating was found to be: extraction temperature 40 °C; solid-solvent ratio 1:20; extraction pH 4.0; cellulase concentration 2.0%. The polysaccharide extraction yield was 5.99% under these optimized conditions. Furthermore, a fundamental investigation of the biosorption of Pb²⁺ from aqueous solution by the C. militaris polysaccharide was performed under batch conditions. The suitable pH (5.0), polysaccharide concentration (0.20 g L^?1), initial Pb²⁺ concentration (300 mg L^?1) and contact time (40 min) were outlined to enhance Pb²⁺ biosorption from aqueous medium. The Langmuir isotherm model and pseudo first order kinetic model fitted well to the data of Pb²⁺ biosorption, suggesting the biosorption of Pb²⁺ onto C. militaris polysaccharide was monolayer biosorption and physical adsorption might be the rate-limiting step that controlled the adsorption process. FTIR analysis showed that the main functional groups of C. militaris polysaccharide involved in adsorption process were carbonyl, carboxyl, and hydroxyl groups.     

Comparative fertilizer properties of digestates from mesophilic and thermophilic anaerobic digestion of dairy manure: focusing on plant growth promoting bacteria (PGPB) and environmental risk

The fertilizer properties of anaerobic digestate depend on the feedstock and operating conditions of digestion. In this study, the comparative fertilizer properties of mesophilic and thermophilic digestates from dairy manure were evaluated for plant nutrient contents, and special attention was paid to plant growth promoting bacteria (PGPB). Two digestates contained similar plant nutrient contents, while the thermophilic digestate contained higher contents of NH₄⁺–N. The quantity of Bacillus and Pseudomonas in the mesophilic digestate was significantly higher than in the thermophilic digestate. Furthermore, Bacillus showed siderophore production and antifungal activity (43.5–75.3%), and Pseudomonas showed siderophore and phytohormone production (4.2–75.2 µg ml^?1). One phosphate solubilizing isolate was also detected in the mesophilic digestate. These results indicated that two digestates showed different fertilizer properties with respect to nutrient contents and PGPB, and digestates had the potential to increase the availability of phosphorus and iron in the soil, both to provide phytohormones to plant roots and protect plants from fungal phytopathogens. The contents of indicator bacteria and heavy metals were analyzed to determine their environmental risk, and the results showed a high reduction in indicator bacteria and lower levels of heavy metals than in other feedstocks.     

Synthesis and Properties of Polyesters from Waste Grapeseed Oil: Comparison with Soybean and Rapeseed Oils

The aim of this study was to investigate the application of grapeseed oil, a waste product from the wine industry, as a renewable feedstock to make polyesters and to compare the properties of these materials with those derived from soybean and rapeseed oils. All three oils were epoxidized to give renewable epoxy monomers containing between 3.8 and 4.7 epoxides per molecule. Polymerisation was achieved with cyclic anhydrides catalysed by 4-methyl imidazole at 170 and 210 °C. Polymers produced from methyl tetrahydrophthalic anhydride (Aradur917^®) had greater tensile strength and Young’s Modulus (tensile strength = 12.8 MPa, Young’s Modulus = 1005 MPa for grapeseed) than methyl nadic anhydride (MNA) derived materials (5.6 and 468 MPa for grapeseed) due to increased volume of MNA decreasing crosslink density. Soybean and grapeseed oils produced materials with higher tensile strength (5.6–29.3 MPa) than rapeseed derived polyesters (2.5–3.9 MPa) due to a higher epoxide functionality increasing crosslinking. T _g’s of the polyesters ranged from ?36 to 62 °C and mirrored the trend in epoxide functionality with grapeseed producing higher T _g polymers (?17 to 17 °C) than soybean (?25 to 6 °C) and rapeseed (?36 to ?27 °C). Grapeseed oil showed similar properties to soybean oil in terms of T _g, thermal degradation and Young’s Modulus but produced polymers of lower tensile strength. Therefore grapeseed oil would only be a viable substitute for soybean for low stress applications or where thermal properties are more important.     

In Vivo and In Vitro Degradation Studies for Poly(3-hydroxybutyrate-<Emphasis Type="Italic">co</Emphasis>-3-hydroxyhexanoate) Biopolymer

Studies have shown that the copolymer poly(3-hydroxybutyrate-co-3-hydroxyhexanoate) [P(HB-co-HHx)] possesses favorable mechanical properties for use in medical supplies and products (e.g., sutures, scaffolds, bone plates). One of the major under-addressed issues associated with the use of biodegradable, bio-based PHA polymers in resorbable medical products is the correlation between the mechanical properties and the in vivo material degradation over time. In this study, P(HB-co-17 mol% HHx) matrices were mechanically tested after either incubation in cultures of human embryonic kidney cells (HEK) for in vitro degradation studies for up to 4 weeks, or inserted into Danio rerio (zebrafish) tissues for in vivo degradation studies for up to 7 weeks. The mechanical properties and scanning electron microscopy (SEM) images of the degraded materials were examined and later correlated to understand the degradation phenomenon. Our results show that Young’s modulus of P(HB-co-17 mol%HHx) during in vitro studies decreased from 3.26 to 2.42 GPa within 4 weeks, and in vivo breakdown resulted in a significant decrease in Young’s modulus with a decrease from 3.26 to 0.51 GPa and a mass loss of 59 % within 7 weeks. SEM images showed the development of pores and cracks on the surface of the material over time. Plasticization and recrystallization were observed and likely play a role in the alteration of mechanical properties.     

Microbial Degradation of UV-Pretreated Low-Density Polyethylene Films by Novel Polyethylene-Degrading Bacteria Isolated from Plastic-Dump Soil

Eleven effective low-density polyethylene (LDPE)-degrading bacterial strains were isolated and identified from landfill soil containing large amounts of plastic materials. The isolates belonged to 8 genera, and included Pseudomonas (areroginosa and putida), Sphingobacterium (moltivorum), Delftia (tsuruhatansis), Stentrophomonas (humi and maltophilia), Ochrobacterum (oryzeae and humi), Micrococcus (luteus), Acinetobacter (pitti), and Citrobacter (amalonaticus). Abiotic degradation of LDPE films by artificial and natural ultraviolet (UV)-exposure was analyzed by FT-IR spectroscopy. LDPE films treated with UV-radiation were also inoculated with the isolates and biofilm production and LDPE degradation were measured. Surface changes to the LDPE induced by bacterial biofilm formation were visualized by Scanning Electron Microscopy. The most active bacterial isolate, IRN19, was able to degrade polyethylene film by 26.8?±?3.04% gravimetric weight over 4 weeks. Analysis of 16S rRNA sequence of this isolate revealed 96.97% similarity in sequence to Acinetobacter pitti, which has not previously been identified as a polyethylene-degrading bacterium. Also, most the effective biofilm forming isolate, IRN11, displayed the highest cell mass production (6.29?±?0.06 log cfu/cm²) after growth on LDPE films, showed 98.74% similarity to Sphingobacterium moltivourum.     

Application of ameliorated wood pulp to recover Cd(II), Pb(II), and Ni(II) from e-waste

In this study, dl-malic acid and hydrogen peroxide were used as leaching agents to remove metals from e-waste (printed-circuit boards) and itaconic acid-grafted poly(vinyl alcohol)-encapsulated wood pulp (IA-g-PVA-en-WP) to uptake metals from leachate with high proficiency [11.63 mg g^?1; 93.03 % for Cd(II), 11.90 mg g^?1; 95.18 % for Pb(II), and 12.14 mg g^?1; 97.08 % for Ni(II)]. Metals were recovered from the loaded biosorbent by desorption studies. The standard analytical techniques, such as elemental analysis, Fourier-transform-infrared spectroscopy, scanning electron microscopy, atomic force microscopy, and thermogravimetric analysis, were used to characterize the recovering agent (biosorbent). At equilibrium, the metal uptake data were fitted to Langmuir and D–R isotherms (R ² > 0.99) significantly, revealing, the homogeneous distribution of active sites on biosorbent’s backbone. The possible mechanism appeared to be ion exchanges of metal ions with H⁺ together with binding over functionalities (COO^?). Dimensionless equilibrium parameter (R _L) showed the favourability of metal uptake at lower concentration, while mean adsorption energy (E) certified the physical binding of metal on functionalities which was further confirmed by sticking probability and activation energy parameters. Reusability studies were also conducted to state the performance of biosorbent.     

The mixing and segregation characteristics of rice straw in a cylindrical bubbling fluidized bed

In the present study, an experiment was performed to investigate the mixing and segregation characteristics of standard sand and rice straw particles in a cylindrical bubbling fluidized bed. The mass ratio (rice straw/standard sand = 0.5–1.25 %) of two particles and superficial gas velocity (0.13–0.18 m/s) were changed as experimental variables. The pressure drop curve and Kramer’s equation were used to determine the minimum fluidization velocity and mixing index, respectively. In all cases, the mixing index was the lowest at U/U _mf = 1.15. Based on the point of U/U _mf = 1.15, the segregation region and mixing region were observed. In the segregation region, mass ratio of 0.75 % showed the lowest mixing index. At the U/U _mf = 1.23 which was selected as the starting of fast pyrolysis considering residence time and the previous fast pyrolysis experiment, mass ratio of 1.25 % showed the highest mixing index which was 0.90.     

Investigation of Biosurfactant Activity and Asphaltene Biodegradation by <Emphasis Type="Italic">Bacillus cereus</Emphasis>

In this research, a biosurfactant-producing bacterium with capability of asphaltene degradation was isolated from oil-contaminated soil samples, and identified as Bacillus cereus. This strain produced an effective biosurfactant in the presence of molasses and the surface tension was reduced to the level of 36.4 mN/m after 48 h under optimum conditions. The optimum values of carbon-to-nitrogen ratio (C:N), pH, and temperature for biosurfactant production were determined as 30:1, 7.3 and 29 °C, respectively, using response surface methodology. The maximum emulsification activity in the culture broth was 53 % after 48 h using kerosene at 25 °C. The goodness of fit of four growth kinetic models including Tessier, Contois, Logistic and Westerhoff was compared for the bacterial growth and molasses utilization of B. cereus in 5-L batch bioreactor during 120 h. Conducted kinetic study showed that biosurfactant production had a good fit with the Contois growth kinetic model (R² = 0.962) and the maximum specific growth rate (µ _max ), saturation constant (K _s ) and the yield of biomass per substrate (Y _x/s ) were determined to be 0.145 h^?1, 1.83 g/L and 0.428 g/g, respectively. The asphaltene biodegradation in flask was evaluated by FTIR analysis and quantified by a spectrophotometer. This bacterium was able to degrade up to 40 % of asphaltene as a sole carbon and energy source after 60 days at 28 °C. The resulting surface tension of 30.2 mN/m with the critical micelle concentration of 23.4 mg/L indicated good efficiency of the biosurfactant.