Nonideal transport of contaminants in heterogeneous porous media: 10. Impact of co-solutes on sorption by porous media with low organic-carbon contents

The impact of co-solutes on sorption of tetrachloroethene (PCE) by two porous media with low organic-carbon contents was examined by conducting batch experiments. The two media (Borden and Eustis) have similar physical properties, but significantly different organic-carbon (OC) contents. Sorption of PCE was nonlinear for both media, and well-described by the Freundlich equation. For the Borden aquifer material (OC = 0.03%), the isotherms measured with a suite of co-solutes present (1,2-dichlorobenzene, bromoform, carbon tetrachloride, and hexachloroethane) were identical to the isotherms measured for PCE alone. These results indicate that there was no measurable impact of the co-solutes on PCE sorption for this system. In contrast to the Borden results, there was a measurable reduction in sorption of PCE by the Eustis soil (OC = 0.38%) in the presence of the co-solutes. The organic-carbon fractions of both media contain hard-carbon components, which have been associated with the manifestation of nonideal sorption phenomena. The disparity in results observed for the two media may relate to relative differences in the magnitude and geochemical nature of these hard-carbon components.     

Nonideal transport of contaminants in heterogeneous porous media: 9 - impact of contact time on desorption and elution tailing

A series of miscible-displacement experiments was conducted to examine the impact of sorption contact time on desorption and elution of trichloroethene from a well-characterized soil. A large number of contact times were examined, spanning 1 h to 4 years (∼2 × 10⁶ h). Effluent trichloroethene concentrations were monitored over a range of greater than six orders of magnitude, allowing characterization of potential asymptotic tailing. The results of the column experiments showed that trichloroethene exhibited extensive elution tailing for all experiments. Each increase in contact time resulted in a successive increase in the extent of tailing. In total, the number of pore volumes of water flushing required to reach the analytical detection limit increased from approximately 1000 for the 1-h contact time to almost 9000 for the 4-year contact time. These results indicate that a contact time of less than 1 h produced a sorbed phase that is relatively resistant to desorption, and that a progressive increase in resistance to desorption occurred with increased contact time. A mathematical model incorporating nonlinear, rate-limited sorption/desorption described by a continuous-distribution reaction function was used to successfully simulate the measured data. The nonlinear sorption, the apparent rapid development of desorption resistance, and the progressive increase in resistance with increasing contact time are consistent with behavior anticipated for sorbate interactions with hard-carbon components of the soil.     

Sorption of chlorinated solvents and degradation products on natural clayey tills

The sorption of chlorinated solvents and degradation products on seven natural clayey till samples from three contaminated sites was investigated by laboratory batch experiments in order to obtain reliable sorption coefficients (K_d values). The sorption isotherms for all compounds were nearly linear, but fitted by Freundlich isotherms slightly better over the entire concentration range. For chloroethylenes, tetrachloroethylene (PCE) was most strongly sorbed to the clayey till samples (K_d = 0.84-2.45 L kg⁻¹), followed by trichloroethylene (TCE, K_d = 0.62-0.96 L kg⁻¹), cis-dichloroethylene (cis-DCE, K_d = 0.17-0.82 L kg⁻¹) and vinyl chloride (VC, K_d = 0.12-0.36 L kg⁻¹). For chloroethanes, 1,1,1-trichloroethane (1,1,1-TCA) was most strongly sorbed (K_d = 0.2-0.45 L kg⁻¹), followed by 1,1-dichloroethane (1,1-DCA, K_d = 0.16-0.24 L kg⁻¹) and chloroethane (CA, K_d = 0.12-0.18 L kg⁻¹). This is consistent with the order of hydrophobicity of the compounds. The octanol-water coefficient (log K_ow) correlated slightly better with log K_d values than log K_oc values indicating that the K_d values may be independent of the actual organic carbon content (f_oc). The estimated log K_oc or log K_d for chlorinated solvents and degradation products determined by regression of data in this study were significantly higher than values determined by previously published empirical relationships. The site specific K_d values as well as the new empirical relationship compared well with calculations on water and soil core concentration for cis-DCE and VC from the Rugårdsvej site. In conclusion, this study with a wide range of chlorinated ethenes and ethanes - in line with previous studies on PCE and TCE - suggest that sorption in clayey tills could be higher than typically expected.     

A controlled field experiment on groundwater contamination by a multicomponent DNAPL: dissolved-plume retardation

A natural gradient emplaced-source (ES) controlled field experiment was conducted at the Borden aquifer research site, Ontario, to study the transport of dissolved plumes emanating from residual dense nonaqueous-phase liquid (DNAPL) source zones. The specific objective of the work presented here is to determine the effects of solute and co-solute concentrations on sorption and retardation of dissolved chlorinated solvent-contaminant plumes. The ES field experiment comprised a controlled emplacement of a residual multicomponent DNAPL below the groundwater table and intensive monitoring of dissolved-phase plumes of trichloromethane (TCM), trichloroethylene (TCE), and perchloroethylene (PCE) plumes continuously generated in the aquifer down gradient from gradual source dissolution. Estimates of plume retardation (and dispersion) were obtained from 3-D numerical simulations that incorporated transient source input and flow regimes monitored during the test. PCE, the most retarded solute, surprisingly exhibited a retardation factor approximately 3 times lower than observed in a previous Borden tracer test by Mackay et al. [Water Resour. Res. 22 (1986) 2017] conducted approximately 150 m away. Also, an absence of temporal trend in PCE retardation contrasted with the previous Borden test. Supporting laboratory studies on ES site core indicated that sorption was nonlinear and competitive, i.e. reduced sorption of PCE was observed in the presence of TCE. Consideration of the effects of relatively high co-solute (TCE) concentration (competitive sorption) in addition to PCE concentration effects (nonlinear sorption) was necessary to yield laboratory-based PCE retardation estimates consistent with the field plume values. Concentration- and co-solute-based sorption and retardation analysis was also applied to the previous low-concentration pulse injection test of Mackay et al. [Water Resour. Res. 22 (1986) 2017] and was able to successfully predict the temporal field retardation trends observed in that test. While it is acknowledged that other "nonideal transport" effects may contribute, our analysis predicts differences in the PCE retardation magnitude and trend between the two experiments that are consistent with field observations based on the marked solute concentration differences that resulted from contrasting source conditions. Solute and co-solute concentration effects have heretofore received little attention, but may have wide significance in aquifers contaminated by point-source pollutants because many plumes contain mixed solutes over wide concentration ranges in strata that are likely subject to nonlinear sorption.     

Impact of anthropogenic emissions and open biomass burning on regional carbonaceous aerosols in South China

Carbonaceous aerosols were studied at three background sites in south and southwest China. Hok Tsui in Hong Kong had the highest concentrations of carbonaceous aerosols (OC = 8.7 ± 4.5 μg/m³, EC = 2.5 ± 1.9 μg/m³) among the three sites, and Jianfeng Mountains in Hainan Island (OC = 5.8 ± 2.6 μg/m³, EC = 0.8 ± 0.4 μg/m³) and Tengchong mountain over the east edge of the Tibetan Plateau (OC = 4.8 ± 4.0 μg/m³, EC = 0.5 ± 0.4 μg/m³) showed similar concentration levels. Distinct seasonal patterns with higher concentrations during the winter, and lower concentrations during the summertime were observed, which may be caused by the changes of the regional emissions, and monsoon effects. The industrial and vehicular emissions in East, Southeast and South China, and the regional open biomass burning in the Indo-Myanmar region of Asia were probably the two major potential sources for carbonaceous matters in this region.     

Sorption kinetic characteristics of polybrominated diphenyl ethers on natural soils

Sorption kinetic characteristics of BDE-28 and BDE-47 on five natural soils with different organic carbon fractions were investigated, and could be satisfactorily described by a two (fast and slow)-compartment first-order model with the ratio of rate constants ranged from 9 to 94 times. The fast compartment made a dominant contribution (71% ∼ 94%) to the total sorption amount in the whole process, and accounted for over 90% of the increase in the total sorption amount at initial 5 h. The influence of the slow compartment on the increase in the total sorption amount became principal (above 90%) in the subsequent stage approximately from 9 h or 25 h to the apparent equilibrium at 265 h. The results proposed the different sorption behaviors of the mathematically classified compartments for BDE-28 and BDE-47, which may correspond to the different soil components, such as soil organic fractions with amorphous and condensed structures, respectively.     

Sorption and desorption hysteresis of organic contaminants by kerogen in a sandy aquifer material

Sorption and desorption hysteresis of 1,2-dichlorobenzene, 1,3,5-trichlorobenzene, naphthalene, and phenanthrene were investigated for the Borden aquifer material with total organic carbon of 0.021% and the isolated natural organic matter (NOM). The isolated NOM is a kerogen type of organic matter with relatively low maturation degree and contained many different types of organic matters including vitrinite particles. The modified Freundlich sorption capacities (logK^′_f and logK^′_foc) are very close for the sorption of the four solutes by the isolated NOM and the original sand, respectively. Isotherm non-linearity (n value) and hysteric behaviors are related to solute molecular properties (e.g. K_ow and molecular size). Kerogen encapsulated by inorganic matrices in the original aquifer may not be accessed fully by solutes. The larger the hydrophobic organic chemical (HOC) (hydrophobic organic contaminant) molecule is, the lower accessibility of the HOC to kerogen. This study disputes widely held hypothesis that sorption to mineral surfaces may play a major role in the overall sorption by low TOC (e.g. 0.1% by mass) geomaterials such as Borden sand. It also demonstrates the importance of the condensed NOM domain, even at very low contents, in the sorption and desorption hysteresis of HOCs in groundwater systems.     

Sorption of 3,4-dichloroaniline on four contrasting Greek agricultural soils and the effect of liming

Sorption of 3,4-dichloroaniline (3,4-DCA) on four typical Greek agricultural soils, with distinct texture, organic matter content and cation exchange capacities, was compared by using sorption isotherms and the parameters calculated from the fitted Freundlich equations. The sorption process of 3,4-DCA to the soil was completed within 48–72 h. The 3,4-DCA sorption on all soils was well described by the Freundlich equation and all sorption isotherms were of the L-type. The sandy clay loam soil with the highest organic matter content and a slightly acidic pH was the most sorptive, whereas the two other soil types, a high organic matter and neutral pH clay and a low organic matter and acidic loam, had an intermediate sorption capacity. A typical calcareous soil with low organic matter had the lowest sorption capacity which was only slightly higher than that of river sand. The 3,4-DCA sorption correlated best to soil organic matter content and not to clay content or cation exchange capacity, indicating the primary role of organic matter. The distribution coefficient (K _d) decreased with increasing initial 3,4-DCA concentration and the reduction was most pronounced with the highly sorptive sandy clay loam soil, suggesting that the available sorption sites of the soils are not unlimited. Liming of the two acidic soils (the sandy clay loam and the loam) raised their pH (from 6.2 and 5.3, respectively) to 7.8 and reduced their sorption capacity by about 50 %, indicating that soil pH may be the second in importance factor (after organic matter) determining 3,4-DCA sorption.     

Influence of soil properties on heavy metal sequestration by biochar amendment: 2. Copper desorption isotherms

Contaminant desorption constrains the long-term effectiveness of remediation technologies, and is strongly influenced by dynamic non-equilibrium states of environmental and biological media. Information is currently lacking in the influence of biochar and activated carbon amendments on desorption of heavy metal contaminants from soil components. In this study, copper sorption-desorption isotherms were obtained for clay-rich, alkaline San Joaquin soil with significant heavy metal sorption capacity, and eroded, acidic Norfolk sandy loam soil having low capacity to retain copper. Acidic pecan shell-derived activated carbon and basic broiler litter biochar were employed in desorption experiments designed to address both leaching by rainfall and toxicity characteristics. For desorption in synthetic rain water, broiler litter biochar amendment diminished sorption-desorption hysteresis. In acetate buffer (pH 4.9), significant copper leaching was observed, unless acidic activated carbon (pH_pzc = 3.07) was present. Trends observed in soluble phosphorus and zinc concentrations for sorption and desorption equilibria suggested acid dissolution of particulate phases that can result in a concurrent release of copper and other sorbed elements. In contrast, sulfur and potassium became depleted as a result of supernatant replacements only when amended carbon (broiler litter biochar) or soil (San Joaquin) contained appreciable amounts. A positive correlation was observed between the equilibrium aluminum concentration and initial copper concentration in soils amended with acidic activated carbon but not basic biochar, suggesting the importance of cation exchange mechanism, while dissolution of aluminum oxides cannot be ruled out.     

Entrapment and dissolution of DNAPLs in heterogeneous porous media

Two-dimensional multiphase flow and transport simulators were refined and used to numerically investigate the entrapment and dissolution behavior of tetrachloroethylene (PCE) in heterogeneous porous media containing spatial variations in wettability. Measured hydraulic properties, residual saturations, and dissolution parameters were employed in these simulations. Entrapment was quantified using experimentally verified hydraulic property and residual saturation models that account for hysteresis and wettability variations. The nonequilibrium dissolution of PCE was modeled using independent estimates of the film mass transfer coefficient and interfacial area for entrapped and continuous (PCE pools or films) saturations. Flow simulations demonstrate that the spatial distribution of PCE is highly dependent on subsurface wettability characteristics that create differences in PCE retention mechanisms and the presence of subsurface capillary barriers. For a given soil texture, the maximum and minimum PCE infiltration depth was obtained when the sand had intermediate (an organic-wet mass fraction of 25%) and strong (water- or organic-wet) wettability conditions, respectively. In heterogeneous systems, subsurface wettability variations were also found to enhance or diminish the performance of soil texture-induced capillary barriers. The dissolution behavior of PCE was found to depend on the soil wettability and the spatial PCE distribution. Shorter dissolution times tended to occur when PCE was distributed over large regions due to an increased access of flowing water to the PCE. In heterogeneous systems, capillary barriers that produced high PCE saturations tended to exhibit longer dissolution times.     

Comparative assessment of metribuzin sorption efficiency of biochar,hydrochar and vermicompost

Abstract

In this study, we used two biochars (BC) produced from grapevine pruning residues (BCgv) and red spruce wood (BCrs), two hydrochars (HC) from urban pruning residues (HCup) and the organic fraction of municipal solid wastes (HCuw), and two vermicomposts (VC) obtained vermicomposting digestates from buffalo manure (VCbm) and mixed feedstock (VCmf). Adsorption kinetics and isotherms of metribuzin onto these materials were performed. Sorption kinetics followed preferentially a pseudo-second-order model, thus indicating the occurrence of chemical interactions between the sorbate and the adsorbents. Adsorption constants were calculated using the Freundlich and Langmuir models. Metribuzin sorption data on BCgv and both HC fitted preferentially the Freundlich equation, whereas on the other materials data fitted both isotherms well (r?>?0.95). Metribuzin sorption capacity of the materials followed the trend BC?>?HC?>?VC. Sorption constants of metribuzin normalised per organic carbon content (K_OC) on BCgv, BCrs, HCup, HCuw, VCbm and VCmf were 561, 383, 251, 214, 102 and 84?L kg^?1, respectively. A significant positive correlation (P?=?0.016) was calculated between distribution coefficients (K_d) of all materials and the corresponding organic carbon contents, thus indicating a prominent role of the organic fraction of these materials in the adsorption of metribuzin.     

Nonequilibrium transport of organic chemicals: The impact of pore-water velocity

The impact of variations in pore-water velocity on the nonequilibrium sorption and transport of organic chemicals was investigated. Miscible displacement experiments were performed with four organic chemicals (dichlorobenzene, naphthalene, tetrachloroethene and p-xylene) and three aquifer materials having low organic-carbon contents (0.02–0.1%). The results of the experiments were analyzed by using a one-dimensional advective-dispersive transport model, wherein sorption is considered instantaneous for a fraction of the sorbent and rate-limited for the remainder. An inverse relationship between the reverse sorption rate constant and the equilibrium sorption constant was evident for each of two velocities. However, there was an order-of-magnitude difference between the rate constants obtained at the two velocities. This suggests the existence of a time-scale effect, which must be accounted for when modeling the transport of organic solutes.     

Enhanced sorption of perfluorooctane sulfonate (PFOS) on carbon nanotube-filled electrospun nanofibrous membranes

Multi-walled carbon nanotube-filled electrospun nanofibrous membranes (MWCNT-ENFMs) were prepared by electrospinning. The addition of MWCNTs (0.5 wt.% vs. ENFMs) doubled the specific surface area and tensile strength of the ENFMs. The MWCNT-ENFMs were used to adsorb perfluorooctane sulfonate (PFOS) in aqueous solutions. The sorption kinetics results showed that the sorption rate of PFOS onto the MWCNT-ENFMs was much higher than the sorption rate of PFOS onto the pure ENFMs control, and the pseudo-second-order model (PSOM) described the sorption kinetics well. The sorption isotherms indicated that the sorption capacity of the MWCNT-ENFMs for PFOS (16.29 ± 0.26 μmol g⁻¹) increased approximately 18 times, compared with the pure ENFMs (0.92 ± 0.06 μmol g⁻¹). Moreover, the solution pH significantly affected the sorption efficiency and sorption mechanism. The MWCNT-ENFMs were negatively charged from pH 2.0–10.0, but the electrostatic repulsion between the MWCNT-ENFMs and PFOS was overcome by the hydrophobic interactions between PFOS and the MWCNTs or nanofibers. The strong hydrophobic interactions between PFOS and the MWCNTs played a dominant role in the sorption process. For the pure ENFMs, the electrostatic repulsion was conquered by the hydrophobic interactions between PFOS and the nanofibers at pH > 3.1. In addition to the hydrophobic interactions, an electrostatic attraction between PFOS and the pure ENFMs was involved in the sorption process at pH < 3.1.     

Locally-calibrated light transmission visualization methods to quantify nonaqueous phase liquid mass in porous media

Five locally-calibrated light transmission visualization (LTV) methods were tested to quantify nonaqueous phase liquid (NAPL) mass and mass reduction in porous media. Tetrachloroethylene (PCE) was released into a two-dimensional laboratory flow chamber packed with water-saturated sand which was then flushed with a surfactant solution (2% Tween 80) until all of the PCE had been dissolved. In all the LTV methods employed here, the water phase was dyed, rather than the more common approach of dyeing the NAPL phase, such that the light adsorption characteristics of NAPL did not change as dissolution progressed. Also, none of the methods used here required the use of external calibration chambers. The five visualization approaches evaluated included three methods developed from previously published models, a binary method, and a novel multiple wavelength method that has the advantage of not requiring any assumptions about the intra-pore interface structure between the various phases (sand/water/NAPL). The new multiple wavelength method is also expected to be applicable to any translucent porous media containing two immiscible fluids (e.g., water-air, water-NAPL). Results from the sand-water-PCE system evaluated here showed that the model that assumes wetting media of uniform pore size (Model C of Niemet and Selker, 2001) and the multiple wavelength model with no interface structure assumptions were able to accurately quantify PCE mass reduction during surfactant flushing. The average mass recoveries from these two imaging methods were greater than 95% for domain-average NAPL saturations of approximately 2.6x10(-2), and were approximately 90% during seven cycles of surfactant flushing that sequentially reduced the average NAPL saturation to 7.5x10(-4).     

Reduction of hexachloroethane to tetrachloroethylene in groundwater

At the Canadian Forces Base, Borden, hexachloroethane (HCE) that was introduced into an unconfined sand aquifer disappeared rapidly, with a half-life of about 40 days. Laboratory-scale studies, initiated to help assess the fate of HCE, indicated that it is reductively biotransformed to tetrachloroethylene (PCE) both by aerobic cultures of wastewater microflora and by microcosms containing unhomogenized Borden aquifer material. The results also indicate that the agents involved in the aquifer transformation of HCE to PCE are not homogeneously distributed in the aquifer material.     

Sorption and transport of trichloroethylene in caliche soil

Sorption of TCE to the caliche soil exhibited linear isotherm at the high TCE concentrations (Co = 122-1300 mg L⁻¹) but Freundlich isotherm at the low concentration range (1-122 mg L⁻¹). Sorption strength of the carbonate fraction of the soil was about 100-fold lower than the sorption strength of soil organic matter (SOM) in the caliche soil, indicating weak affinity of TCE for the carbonate fraction of the soil. Desorption of TCE from the caliche soil was initially rapid (7.6 × 10⁻⁴ s⁻¹), then continued at a 100-fold slower rate (7.7 × 10⁻⁶ s⁻¹). Predominant calcium carbonate fraction of the soil (96%) was responsible for the fast desorption of TCE while the SOM fraction (0.97%) controlled the rate-limited desorption of TCE. Transport of TCE in the caliche soil was moderately retarded with respect to the water (R = 1.75-2.95). Flow interruption tests in the column experiments indicated that the rate-limited desorption of TCE controlled the non-ideal transport of TCE in the soil. Modeling studies showed that both linear and non-linear nonequilibrium transport models provided reasonably good match to the TCE breakthrough curves (r² = 0.95-0.98). Non-linear sorption had a negligible impact on both the breakthrough curve shape and the values of sorption kinetics parameters at the high TCE concentration (Co = 1300 mg L⁻¹). However, rate-limited sorption/desorption processes dominated at this concentration. For the low TCE concentration case (110 mg L⁻¹), in addition to the rate-limited sorption/desorption, contribution of the non-linear sorption to the values of sorption kinetics became fairly noticeable.     

Cesium migration in saturated silica sand and Hanford sediments as impacted by ionic strength

Large amounts of 137Cs have been accidentally released to the subsurface from the Hanford nuclear site in the state of Washington, USA. The cesium-containing liquids varied in ionic strengths, and often had high electrolyte contents, mainly in the form of NaNO3 and NaOH, reaching concentrations up to several moles per liter. In this study, we investigated the effect of ionic strengths on Cs migration through two types of porous media: silica sand and Hanford sediments. Cesium sorption and transport was studied in 1, 10, 100, and 1000 mM NaCl electrolyte solutions at pH 10. Sorption isotherms were constructed from batch equilibrium experiments and the batch-derived sorption parameters were compared with column breakthrough curves. Column transport experiments were analyzed with a two-site equilibrium-nonequilibrium model. Cesium sorption to the silica sand in batch experiments showed a linear sorption isotherm for all ionic strengths, which matched well with the results from the column experiments at 100 and 1000 mM ionic strength; however, the column experiments at 1 and 10 mM ionic strength indicated a nonlinear sorption behavior of Cs to the silica sand. Transport through silica sand occurred under one-site sorption and equilibrium conditions. Cesium sorption to Hanford sediments in both batch and column experiments was best described with a nonlinear Freundlich isotherm. The column experiments indicated that Cs transport in Hanford sediments occurred under two-site equilibrium and nonequilibrium sorption. The effect of ionic strength on Cs transport was much more pronounced in Hanford sediments than in silica sands. Effective retardation factors of Cs during transport through Hanford sediments were reduced by a factor of 10 when the ionic strength increased from 100 to 1000 mM; for silica sand, the effective retardation was reduced by a factor of 10 when ionic strength increased from 1 to 1000 mM. A two order of magnitude change in ionic strength was needed in the silica sand to observe the same change in Cs retardation as in Hanford sediments.     

Passive dosing: an approach to control mutagen exposure in the Ames fluctuation test

By using dialysis equilibrium experiments, the sorption of a branched nonylphenol isomer [4-(1-ethyl-1,3-dimethylpentyl)-phenol] (NP111) on various humic acids (HAs) isolated from river sediments and two reference HAs was studied. The HAs were characterized by solid-state ¹³C direct polarization/magic angle spinning nuclear magnetic resonance (¹³C DP/MAS NMR) spectroscopy. Sorption isotherms of NP111 on HAs were described by a linear model. The organic carbon-normalized sorption coefficient (K_OC) ranged from 2.3 × 10³ to 1.5 × 10⁴ L kg⁻¹. Interestingly, a clear correlation between K_OC value and alkyl C content was observed, indicating that the aliphaticity of HAs markedly dominates the sorption of NP111. These new mechanistic insights about the NP111 sorption indicate that the fate of nonylphenols in soil or sediment depends not only on the content of HA, but also on its structural composition.     

Description of sorbing tracers transport in fractured media using the lattice model approach

The transport of contaminants in fractured media is a complex phenomenon with a great environmental impact. It has been described with several models, most of them based on complex partial differential equations, that are difficult to apply when equilibrium and nonequilibrium dynamics are considered in complex boundaries. With the aim of overcoming this limitation, a combination of two lattice Bathnagar, Gross and Krook (BGK) models, derived from the lattice Boltzmann model, is proposed in this paper. The fractured medium is assumed to be a single fissure in a porous rock matrix. The proposed approach permits us to deal with two processes with different length scales: advection-dispersion in the fissure and diffusion within the rock matrix. In addition to the mentioned phenomena, sorption reactions are also considered. The combined model has been tested using the experimental breakthrough curves obtained by Garnier et al. (Garnier, J.M., Crampon, N., Préaux, C., Porel, G., Vreulx, M., 1985. Tra?age par 13C, 2H, I- et uranine dans la nappe de la craie sénonienne en écoulement radial convergent (Béthune, France). J. Hidrol. 78, 379-392.) giving acceptable results. A study on the influence of the lattice BGK models parameters controlling sorption and matrix diffusion on the breakthrough curves shape is included.     

Effect of fly ash on metsulfuron-methyl sorption and leaching in soils

This investigation was undertaken to determine the effect of amendment of two fly ashes [Kota and Inderprastha (IP)] on sorption behavior of metsulfuron-methyl in three Indian soil types. Kota fly ash (5%) did not show any effect on herbicide sorption while IP fly ash significantly enhanced the sorption. Further studies on metsulfuron-methyl sorption-desorption behavior in 0.5, 1, 2, and 5% IP fly ash-amended soils suggested that effect of fly ash varied with soil type and better effect was observed in low organic carbon content soils. The sorption-desorption isotherms fitted very well to the Freundlich sorption equation and, in general, slope (1/n) values less than unity were observed. Metsulfuron-methyl sorption in the IP fly ash-amended soils showed strong correlation with the fly ash content and compared to the Freundlich sorption constant (K _f), K _FA values (sorption normalized to fly ash content) showed less variation. Metsulfuron-methyl leaching studies suggested greater retention of herbicide in the application zone in IP fly ash-amended soils, but effect varied with soil type and no herbicide leaching was observed in 5% fly ash-amended soils. The study suggested that all coal fly ashes are not effective in enhancing the sorption of metsulfuron-methyl in soils. However, one which enhanced herbicide sorption, could play an important role in reducing its leaching losses.