Influence of corn steep liquor and glucose on colonization of control and CCB (Cu/Cr/B)-treated wood by brown rot fungi

There are increasing problems with regard to the disposal of treated wood waste. Due to heavy metals or arsenic in impregnated wood waste, burning and landfill disposal options are not considered to be environmentally friendly solutions for dealing with this problem. Extraction of the heavy metals and recycling of the preservatives from the wood waste is a much more promising and environmentally friendly solution. In order to study the scale up of this process, copper/chromium/boron-treated wood specimens were exposed to copper tolerant (Antrodia vaillantii and Leucogyrophana pinastri) and copper sensitive wood decay fungi (Gloeophyllum trabeum and Poria monticola). Afterwards, the ability of fungal hyphae to penetrate and overgrow the wood specimens was investigated. The fungal growths were stimulated by immersing the specimens into aqueous solution of glucose or corn steep liquor prior to exposure to the fungi. The fastest colonization of the impregnated wood was by the copper tolerant A. vaillantii. Addition of glucose onto the surface of the wood specimens increased the fungi colonization of the specimens; however, immersion of the specimens into the solution of corn steep liquor did not have the same positive influence. These results are important in elucidating copper toxicity in wood decay fungi and for using these fungi for bioremediation of treated wood wastes.     

Plates made with solid waste from the recycled paper industry

The results of assays carried out on plates used in the construction industry, manufactured entirely with solid wastes of a recycled paper plant, are presented and compared with the results obtained using agglomerated wood and plywood plates. Previous results had shown that wastes are composed essentially of polymers when these wastes are generated by recycled paper produced with the “waved type II” shavings. These solid wastes were placed in a mold that was heated and pressed with a hydraulic press in order to obtain the plates. The waste-produced plates were submitted to tests for humidity, swelling, water absorption, density, modulus of rupture-static bending, modulus of elasticity and direct screw withdrawal. These same assays had been carried out on two types of commercial wood plates, agglomerated wood and plywood, in order to compare the results with those obtained with the waste plate. Waste plates had similar behavior to the agglomerated wood plate, but it was possible to distinguish greater flexibility in the waste-produced plate and a significant difference in the tests for swelling and water absorption which showed the waste plate had a better performance than the agglomerated wood and plywood plates.     

Furniture wood wastes: Experimental property characterisation and burning tests

Referring to the industrial wood waste category (as dominant in the provincial district of Pesaro-Urbino, Marche Region, Italy), this paper deals with the experimental characterisation and the carrying out of non-controlled burning tests (at lab- and pilot-scale) for selected “raw” and primarily “engineered” (“composite”) wood wastes.The property characterisation has primarily revealed the following aspects: potential influence on moisture content of local weather conditions at outdoor wood waste storage sites; generally, higher ash contents in “engineered” wood wastes as compared with “raw” wood wastes; and relatively high energy content values of “engineered” wood wastes (ranging on the whole from 3675 to 5105 kcal kg⁻¹ for HHV, and from 3304 to 4634 kcal kg⁻¹ for LHV).The smoke qualitative analysis of non-controlled lab-scale burning tests has primarily revealed: the presence of specific organic compounds indicative of incomplete wood combustion; the presence exclusively in “engineered” wood burning tests of pyrroles and amines, as well as the additional presence (as compared with “raw” wood burning) of further phenolic and containing nitrogen compounds; and the potential environmental impact of incomplete industrial wood burning on the photochemical smog phenomenon.Finally, non-controlled pilot-scale burning tests have primarily given the following findings: emission presence of carbon monoxide indicative of incomplete wood combustion; higher nitrogen oxide emission values detected in “engineered” wood burning tests as compared with “raw” wood burning test; and considerable generation of the respirable PM₁ fraction during incomplete industrial wood burning.     

Comparisons of four categories of waste recycling in China's paper industry based on physical input-output life-cycle assessment model

Waste recycling for paper production is an important component of waste management. This study constructs a physical input-output life-cycle assessment (PIO-LCA) model. The PIO-LCA model is used to investigate environmental impacts of four categories of waste recycling in China’s paper industry: crop straws, bagasse, textile wastes and scrap paper. Crop straw recycling and wood utilization for paper production have small total intensity of environmental impacts. Moreover, environmental impacts reduction of crop straw recycling and wood utilization benefits the most from technology development. Thus, using crop straws and wood (including wood wastes) for paper production should be promoted. Technology development has small effects on environmental impacts reduction of bagasse recycling, textile waste recycling and scrap paper recycling. In addition, bagasse recycling and textile waste recycling have big total intensity of environmental impacts. Thus, the development of bagasse recycling and textile waste recycling should be properly limited. Other pathways for reusing bagasse and textile wastes should be explored and evaluated. Moreover, imports of scrap paper should be encouraged to reduce large indirect impacts of scrap paper recycling on domestic environment.     

Use of FGD gypsum in fire resistant panels

Gypsum from power plant flue gas desulphurization units (FGD gypsum) is a combustion by-product produced in high quantities. In this paper, gypsum panels composed of 100% FGD gypsum from two power plants have been subjected to different physico-chemical (density, pH, humidity), mechanical (flexural and compressive strength, surface hardness, impact resistance), fire resistance and environmental tests (leaching and radioactivity). The results obtained have been compared with the requirements established in some European standards for commercial gypsum and other standards for similar products. In addition, the panels manufactured have been compared with commercial gypsum panels in order to determine the recycling possibilities of this kind of material in this application.     

Changes in fungal population of fly ash and vinasse mixture during vermicomposting by Eudrilus eugeniae and Eisenia fetida: documentation of cellulase isozymes in vermicompost

Fly ash (FA) and vinasse (VN), two industrial wastes, are generated in huge amounts and cause serious hazards to the environment. In this experiment, different proportions of these two wastes were used as food for two epigeic earthworms (Eisenia fetida and Eudrilus eugeniae) to standardize the recycling technique of these two wastes and to study their effect on fungal especially cellulolytic fungal population, cellulase activity and their isozyme pattern, chitin content and microbial biomass of waste mixture during vermicomposting. Increasing VN proportion from 25% to 50% or even higher, counts of both fungi and cellulolytic fungi in waste mixtures were significantly (P ? 0.05) increased during vermicomposting. Higher cellulase activity in treatments having 50% or more vinasse might be attributed to the significantly (P ? 0.05) higher concentration of group I isozyme while concentrations of other isozymes (group II and III) of cellulase were statistically at par. Higher chitin content in vinasse-enriched treatments suggested that fungal biomass and fungi-to-microbial biomass ratio in these treatments were also increased due to vermicomposting. Results revealed that Eudrilus eugeniae and Eisenia fetida had comparable effect on FA and VN mixture during vermicomposting. Periodical analysis of above-mentioned biochemical and microbial properties and nutrient content of final vermicompost samples indicated that equal proportion (1:1, w/w) of FA and VN is probably the optimum composition to obtain best quality vermicompost.     

Characteristics of wood–fiber plastic composites made of recycled materials

This study investigates the feasibility of using recycled high density polyethylene (rHDPE), polypropylene (rPP) and old newspaper (rONP) fiber to manufacture experimental composite panels. The panels were made through air-forming and hot press. The effects of the fiber and coupling agent concentration on tensile, flexural, internal bond properties and water absorption and thickness swelling of wood–fiber plastic composites were studied. The use of maleated polypropylene as coupling agent improved the compatibility between the fiber and both plastic matrices and mechanical properties of the resultant composites compared well with those of non-coupled ones. Based on the findings in this work, it appears that recycled materials can be used to manufacture value-added panels without having any significant adverse influence on board properties. It was also found that composites with rHDPE provided moderately superior properties, compared with rPP samples.     

Leather Insole with Acupressure Effect: New Perspectives

Some wastes contain many reusable substances of high value. Solid leather waste is one such potential waste which can be converted into value added products. This study attempts to prepare leather insoles with acupressure effect from finished leather wastes and used leather wastes. Leather with acupressure effect (LAE) was fabricated using regenerated leather. LAE was characterized physico-chemically using Fourier transform infrared spectroscopy, thermo gravimetric analysis and scanning electron microscopy. Foot pressure measurements were done using LAE insoles on healthy individuals. Results proved that LAE insoles were able to increase the foot pressure of the wearer and thereby created an acupressure effect in them. Wearing of footwear with LAE insoles were beneficial compared to regular insoles. LAE possessed the required mechanical properties for insole production and it was also biodegradable in nature. The study proves that these composites could be successfully used for the production of cost-effective leather goods and therapeutic footwear. Production of useful byproducts from wastes is income generating and at the same time reduces environmental pollution and a feasible technology for waste recycling has been proved in this study.     

Utilization of waste tire rubber in manufacture of oriented strandboard

Some physical and mechanical properties of oriented strandboards (OSBs) containing waste tire rubber at various addition levels based on the oven-dry strand weight, using the same method as that used in the manufacture of OSB. Two resin types, phenol–formaldehyde (PF) and polyisocyanate, were used in the experiments. The manufacturing parameters were: a specific gravity of 0.65 and waste tire rubber content (10/90, 20/80 and 30/70 by wt.% of waste tire rubber/wood strand). Average internal bond values of PF-bonded OSB panels with rubber chips were between 17.6% and 48.5% lower than the average of the control samples while polyisocyanate bonded OSBs were 16.5–50.6%. However, water resistance and mechanical properties of OSBs made using polyisocyanate resin were found to comply with general-purpose OSB minimum property requirements of EN 300 Type 1 (1997) values for use in dry conditions at the lowest tire rubber loading level (10%) based on the oven-dry panel weight. The tire rubber improved water resistance of the OSB panel due to its almost hydrophobic property. Based on the findings obtained from this study, we concluded that waste tire rubber could be used for general-purpose OSB manufacturing up to 10% ratio based on the oven-dry panel weight.     

Choosing a sustainable demolition waste management strategy using multicriteria decision analysis

This paper presents an application of the ELECTRE III decision-aid method in the context of choosing a sustainable demolition waste management strategy for a case study in the city of Lyon, France. This choice of waste management strategy takes into consideration the sustainable development objectives, i.e. economic aspects, environmental consequences, and social issues. Nine alternatives for demolition waste management were compared with the aid of eight criteria, taking into account energy consumption, depletion of abiotic resources, global warming, dispersion of dangerous substances in the environment, economic activity, employment, and quality of life of the local population. The case study concerned the demolition of 25 buildings of an old military camp. Each alternative was illustrated with different waste treatments, such as material recovery, recycling, landfilling, and energy recovery. The recommended solution for sustainable demolition waste management for the case study is a selective deconstruction of each building with local material recovery in road engineering of inert wastes, local energy recovery of wood wastes, and specific treatments for hazardous wastes.     

Leaching behaviour of hazardous demolition waste

Demolition wastes are generally disposed of in unlined landfills for inert waste. However, demolition wastes are not just inert wastes. Indeed, a small fraction of demolition waste contains components that are hazardous to human health and the environment, e.g., lead-based paint, mercury-contained in fluorescent lamps, treated wood, and asbestos. The objective of this study is to evaluate the release potential of pollutants contained in these hazardous components when they are mixed with inert wastes in unlined landfills. After identification of the different building products which can contain hazardous elements and which can be potentially pollutant in landfill scenario, we performed leaching tests using three different lysimeters: one lysimeter containing only inert wastes and two lysimeters containing inert wastes mixed with hazardous demolition wastes. The leachates from these lysimeters were analysed (heavy metals, chlorides, sulphates fluoride, DOC (Dissolved Organic Carbon), phenol index, and PAH). Finally, we compared concentrations and cumulative releases of elements in leachates with the limits values of European regulation for the acceptance of inert wastes at landfill. Results indicate that limit values are exceeded for some elements. We also performed a percolation column test with only demolition hazardous wastes to evaluate the specific contribution of these wastes in the observed releases.     

Combustion kinetics of sewage sludge and combustible wastes

This study estimated the kinetics of the mono- and co-combustion of sewage sludge pellets and combustible wastes such as municipal solid waste (MSW) and refuse-derived fuel (RDF). Sewage sludge was manufactured into pellets with a diameter of 8, 12, or 16 mm and a length of 30 mm. The RDF was composed of paper and plastics and was formed into pellets with a diameter of 8 mm and a length of 30 mm. MSW samples were synthesized using combustible wastes such as garbage, paper, plastics, and wood. The MSW was adjusted to have a moisture content of around 40% after shredding to under 10 mm. A laboratory-scale batch type stoker incinerator was used for the combustion and the gas composition of the flue gas was measured. The activation energy was calculated using the experimental results, and then the relation of the decomposition rate and reaction time was evaluated using the shrinking core model. The decomposition rate of the sludge pellets decreased as their diameter and moisture content increased, and the co-combustion of sludge pellets and combustible waste was affected by the amount of combustible waste. The individual combustion rates of the cylindrical sludge pellets or RDF were mainly controlled by the chemical reaction, but in the case of shredded MSW it was mostly influenced by gas diffusion. The rate for the co-combustion of sludge pellets and combustible wastes was mainly determined by the combustion rate of the combustible waste. The activation energy of the 8-mm-diameter sludge pellets was between 6.70 and 10.0 kcal/mol, according to the moisture content, but it was lower for MSW and RDF. In the case of MSW co-combustion, the reaction rate accelerated as the moisture content of the sludge pellets decreased, but it was markedly increased by the addition of RDF, regardless of the sludge moisture content.     

Enzyme-Retted Flax Fiber and Recycled Polyethylene Composites

Municipal solid wastes generated each year contain potentially useful and recyclable materials for composites. Simultaneously, interest is high for the use of natural fibers, such as flax (Linum usitatissimum L.), in composites thus providing cost and environmental benefits. To investigate the utility of these materials, composites containing flax fibers with recycled high density polyethylene (HDPE) were created and compared with similar products made with wood pulp, glass, and carbon fibers. Flax was either enzyme- or dew-retted to observe composite property differences between diverse levels of enzyme formulations and retting techniques. Coupling agents would strengthen binding between fibers and HDPE but in this study fibers were not modified in anyway to observe mechanical property differences between natural fiber composites. Composites with flax fibers from various retting methods, i.e., dew- vs. enzyme-retting, behaved differently; dew-retted fiber composites resulted in both lower strength and percent elongation. The lowest level of enzyme-retting and the most economical process produces composites that do not appear to differ from the highest level of enzyme-retting. Flax fibers improved the modulus of elasticity over wood pulp and HDPE alone and were less dense than glass or carbon fiber composites. Likely, differences in surface properties of the various flax fibers, while poorly defined and requiring further research, caused various interactions with the resin that influenced composite properties.     

Effects of Waste Paper Sludge on the Physico-Mechanical Properties of High Density Polyethylene/Wood Flour Composites

The objective of this work was to determine some physical and mechanical properties of the high density polyethylene (HDPE) composites reinforced with various mixtures of the paper sludge and the wood flour, and to evaluate the coupling agent performance. The waste sludge materials originating from two different sources including paper making waste water treatment sludge (PS) and ink-eliminated sludge (IES) were characterized in terms of physico-chemical properties. In the experiment, four levels of paper sludge (20, 30, 40 and 60 wt%), three levels of wood flour (20, 40 and 60 wt%), and two levels of coupling agent (MAPE) content (2 and 3 wt%) were used. The flexural properties of the composites were positively affected by the addition of the sludge. Especially, tensile modulus improved with the increase of paper sludge content. With the addition of MAPE, flexural properties improved considerably compared with control specimens (without any coupling agent). The results showed that the water absorption (WA) and thickness swelling (TS) values of the samples decreased considerably with increasing sludge content in the composite, while they increased with increasing wood flour content. It is to be noted that with incorporation of MAPE in the composite formulation, the compatibility between the wood flour and HDPE was enhanced through esterification, which reduced the WA and TS and improved the mechanical properties. Composites made with IES exhibited superior physico-mechanical properties compared with the PS filled composites. Overall results suggest that the waste paper sludge materials were capable of serving as feasible reinforcing fillers for thermoplastic polymer composites.     

Pulp and paper plant wastes valorisation in bituminous mixes

Nowadays, the increasing amount of wastes is a concerning reality and the environmental aspects has become a major priority. Following this worry, the purpose of this experimental study was to investigate the possibility of using pulp and paper inorganic wastes, named dregs and grits, in bituminous mixtures as aggregate replacement to reduce environmental effects of these wastes disposal.First, the wastes were chemically and physically characterized and also tested primarily taking into account the requirements for aggregates in bituminous mixtures. Then, formulations were prepared replacing aggregates with wastes in different amounts. The mechanical properties of these mixtures containing wastes were compared with reference samples based on standard methods.According to the results it was possible to verify that grits had a good performance and it might be directly tested industrially as an aggregate in road construction. On the other hand, dregs need to be treated before incorporation to guarantee stable mixes in terms of water sensitivity.     

Properties of Composite Panels Made from Tetra-Pak and Polyethylene Waste Material

The objective of this study was to evaluate some of the properties of experimental composite panels manufactured from waste packaging materials without using any additional binders. Particles from three types of materials, namely Tetra-Pak, food packaging films (FPEF) as recycled stretch wraps, and candy polyethylene wrappers (CPEW) were used at different ratios in the panels at a target density of 900 kg/m³. Modulus of rupture (MOR), screw holding strength and dimensional stability in the form of thickness swelling and water absorption of the panels were determined according to European (EN) standards. Based on the findings in this work it was determined that the ratio of different raw materials significantly influenced overall properties of the samples. The highest MOR value of 15.5 MPa was determined for the samples having 40 % Tetra-Pak and 60 % CPEW particles. Modulus of rupture values of the panels decreased with decreasing content of CPEW in the samples. The increased content of Tetra-Pak particles in the samples also resulted in reduction of their strength characteristics and dimensional stability. Properties of the samples considered in this work satisfied minimum requirements of typical particleboard stated in EN standards. It appears that such waste material would have potential to be used as raw material for value-added composite production using no adhesive in the panels and, therefore, such panels would possibly create significant ecological impact as green product.     

Enrichment of elements in industrial waste incineration bottom ashes obtained from three different types of incinerators,as studied by ICP-AES and ICP-MS

The elemental composition of the industrial waste incineration bottom ash (IWIBA) samples collected from three different types of incinerator with different kinds of wastes were compared. The major-to-ultratrace elements in the IWIBA samples were determined by inductively coupled plasma atomic emission spectrometry (ICP-AES) and inductively coupled plasma mass spectrometry (ICP-MS). As a result, ca. 40 elements in the concentration range from milligrams per gram to submicrograms per gram could be determined with relative standard deviations of less than 5%. The IWIBA sample from petrochemical wastes contained lower concentrations of the elements, because fewer mineral constituents were contained in the input waste materials. On the contrary, the elemental concentrations in the IWIBA sample from industrial solid wastes provided the highest values for most elements, while the elemental compositions of the IWIBA sample from food wastes were similar to those of municipal solid waste incineration bottom ash. In addition, it was found from the analytical results that the levels of various heavy metals such as Cr, Mn, Fe, Ni, Cu, As, Zr, Mo, Sb, Ba, and Pb were higher in the IWIBA samples than in municipal solid waste incineration bottom ash. The enrichment factors of the elements in the IWIBA samples were estimated from the analytical results to compare the elemental distributions in incineration bottom ashes in relation to their mining influence factors, which are the indices for human use of the elements.     

Determination of specific gravity of municipal solid waste

This investigation was conducted to evaluate experimental determination of specific gravity (G_s) of municipal solid waste (MSW). Water pycnometry, typically used for testing soils was adapted for testing MSW using a large flask with 2000 mL capacity and specimens with 100–350 g masses. Tests were conducted on manufactured waste samples prepared using US waste constituent components; fresh wastes obtained prior and subsequent to compaction at an MSW landfill; and wastes obtained from various depths at the same landfill. Factors that influence specific gravity were investigated including waste particle size, compaction, and combined decomposition and stress history. The measured average specific gravities were 1.377 and 1.530 for as-prepared/uncompacted and compacted manufactured wastes, respectively; 1.072 and 1.258 for uncompacted and compacted fresh wastes, respectively; and 2.201 for old wastes. The average organic content and degree of decomposition were 77.2% and 0%, respectively for fresh wastes and 22.8% and 88.3%, respectively for old wastes. The G_s increased with decreasing particle size, compaction, and increasing waste age. For fresh wastes, reductions in particle size and compaction caused occluded intraparticle pores to be exposed and waste particles to be deformed resulting in increases in specific gravity. For old wastes, the high G_s resulted from loss of biodegradable components that have low G_s as well as potential access to previously occluded pores and deformation of particles due to both degradation processes and applied mechanical stresses. The G_s was correlated to the degree of decomposition with a linear relationship. Unlike soils, the G_s for MSW was not unique, but varied in a landfill environment due both to physical/mechanical processes and biochemical processes. Specific gravity testing is recommended to be conducted not only using representative waste composition, but also using representative compaction, stress, and degradation states.     

Wood Polypropylene (PP) Composites Manufactured by Mango Wood Waste with Virgin or Recycled PP: Mechanical,Morphology, Melt Flow Index and Crystalline Behaviour

Compositions of wood-polypropylene composites (WPCs) are prepared through melt compounding followed by injection moulding. WPCs are formulated for eight compositions with a different weight ratio of wood, virgin or recycled polypropylene and coupling agent. WPCs compositions are compared in terms of Melt Flow Index, Tensile, FESEM images, Flexural and crystallinity index for same operating variable conditions. From the results, recycled polypropylene based WPCs are superior in comparison to virgin polypropylene based WPCs. With the addition of 5 % coupling agent in recycled polypropylene-based composites for 45:50 composition, tensile and flexural values of WPCs are higher in comparison to all composition and neat virgin or recycled polypropylene. This work stands for the utilization of waste wood with recycled plastic for replacement of wood and virgin plastic.     

Fiber from DDGS and Corn Grain as Alternative Fillers in Polymer Composites with High Density Polyethylene from Bio-based and Petroleum Sources

The steady increase in production of corn based ethanol fuel has dramatically increased the supply of its major co-product known as distiller’s dried grain with solubles (DDGS). Large amount of DDGS and corn flour are used as an animal feed. The elusieve process can separate DDGS or corn flour into two fractions: DDGS fraction with enhanced protein and oil content or corn flour fraction with high starch content, and hull fiber. This study investigated the feasibility of using fiber from DDGS and corn grain as alternative fillers to wood fiber in high density polyethylene (HDPE) composites made with two different sources of polymers. Two fiber loading rates of 30 and 50% were evaluated for fiber from DDGS, corn, and oak wood (control) to assess changes in various physical and mechanical properties of the composite materials. Two HDPE polymers, a bio-based HDPE made from sugarcane (Braskem), and a petroleum based HDPE (Marlex) were also compared as substrates. The biobased polymer composites with DDGS and corn fibers showed significantly lower water absorption than the Marlex composite samples. The Braskem composite with 30% DDGS fiber loading showed the highest impact resistance (80 J/m) among all the samples. The flexural properties showed no significant difference between the two HDPE composites.