Characterisation of Airborne Particulate Pollution in The Cu Smelter and Former Mining Town of Karabash, South Ural Mountains of Russia

Airborne total suspended particulates (TSP), dusts from smelter blast furnace and converter stacks, and filtrates of snow melt waters have been characterised in the Cu smelter and former mining town of Karabash, Russia. TSP was collected at sites up- and downwind of the smelter and large waste and tailings dumps (Oct. 2000 and July 2001). Methods for particle size, mineralogical and elemental determinations have been tested and described, and a new PSD-MicroSOURCE XRD technique developed for the mineralogical analysis of microsamples on filter substrates. TSP in downwind samples has a mean equivalent spherical diameter of 0.5 microm (s.d. = 0.2) and was found to be 100% respirable. The main element of human health/environmental concern, above Russian maximum permitted levels (1 microg m(-3), average over any time period), was Pb which was measured at 16-30 microg m(-3) in downwind samples. Individual particulates mainly consisted of complex mixtures of anglesite (PbSO4), Zn2SnO4 and poorly ordered Zn sulphates. From experimental and theoretical considerations, a high proportion of contained Pb, Zn, Cd and As in this material is considered to be in a readily bioavailable form. Chemical and mineralogical differences between the TSP, stack dusts and snow samples are discussed, as well as the implications for human and regional environmental health.     

无锡市国控环境空气自动监测站点周边裸土分布高分辨率遥感监测

以无锡市为研究区,使用过境时间相近的哨兵2号Sentinel-2和Landsat8影像,综合使用NDSI、NDISI、MNDWI、LST等指数进行决策树分类,获得10 m高空间分辨率的土地利用分类结果和裸土分布,裸土提取精度达到94.13%。统计了无锡市与8个国控环境空气自动监测站点1、2、3 km缓冲区范围内的裸土分布情况,并与各站点监测的大气颗粒物浓度进行相关性分析。结果表明,国控环境空气自动监测站点周边裸土面积对颗粒物浓度有较大影响,其中对PM₁₀浓度的影响明显大于PM_2.5;相比于1 km和3 km,2 km缓冲区范围内的裸土面积对PM₁₀浓度的影响最大,建议环境管理部门重点关注无锡地区国控监测站点周边2 km范围内的裸土扬尘源分布情况。     

The ability of biological and organic synthetic materials to accumulate atmospheric particulates containing copper, lead, nickel and strontium

This work was aimed at finding materials that could be used as alternatives to lichens as air quality monitors since the high natural variability and the large amount of lichen collected are two drawbacks of the use of these organisms. Lichen Flavoparmelia caperata(L.) Hale was exposed in three different forms (transplant, detached from the substratum and as a biomass-ground and homogeneized) and compared to the planetree bark (Platanus hybrida Brot.), exposed as a biomass, and two organic synthetic materials (Chelex(R) 100 resin and cellulose acetate). Materials were exposed for two months in the winter, spring and summer, at three Portuguese coastal cities. The results showed that the airborne accumulations of Cu, Ni, Pb and Sr were partially dependent on the meteorological conditions but mainly dependent on the nature of the exposed material. The standard deviations of the synthetic materials or homogenized biomass were the same or greater than lichen transplants or detached. The accumulation by biological materials, of the four studied elements, was comparable to the lichen transplant accumulation. The replacement of the traditional transplants by the biomass was not considered advantageous, since their preparation is time-consuming. Therefore lichens remain the most suitable in biomonitoring studies. The exposure of detached lichen allows the accurate measurement of the exposed area/volume so it can be useful to relate atmospheric deposition rates with the lichen metal content. The synthetic materials accumulated Cu and Ni and should only be used as an alternative to traditional transplants when these are the elements of interest.     

Analysis of heavy metals in atmospheric particulates in relation to their bioaccumulation in explanted Pseudevernia furfuracea thalli

Lichens explants and airborne particulates were analysed for Cr, Zn, Cd, Pb, Ni, Fe, Mn and Cu content in a rural site in the province of Vercelli (Piedmont, N. Italy). Thalliof the fruticose lichen Pseudevernia furfuracea were collected from an uncontaminated area and exposed for one yearusing two different techniques. Particulates were collected using a continuously operating particulate sampler set up nearthe lichens explanted throughout the experiment survey.The results confirm both the importance of assessing contamination in rural areas corroborated by the analysis of the presence of the heavy metals in particulates in relationto the main wind directions and the validity of this lichen asbiomonitor of airborne metal pollution, although meaningfuldifferences were pointed out between the two different techniques of exposure. The significant correlation between most of the metals accumulated by lichens and the metal air concentrations shows a good evidence of their ability to represent atmospheric contamination.     

Sources of lead and zinc associated with metal smelting activities in the Trail area,British Columbia,Canada

The spatial distribution and deposition of lead and zinc emitted from the Trail smelter, British Columbia, Canada, was studied by strategically locating moss bags in the area surrounding the smelter and monitoring the deposition of elements every three months. A combined diffusion/distribution model was applied to estimate the relative contribution of stack-emitted material and material emitted from the secondary sources (e.g., wind-blown dust from ore/slag storage piles, uncovered transportation/trucking of ore, and historical dust). The results indicate that secondary sources are the major contributor of lead and zinc deposited within a short distance from the smelter. Gradually, the stack emissions become the main source of Pb and Zn at greater distances from the smelter. Typical material originating from each source was characterized by SEM/EDX, which indicated a marked difference in their morphology and chemical composition.     

Air quality and deposition of trace elements in Didouche Mourad, Algeria

Total suspended particulate matter and deposition fluxes of particles were investigated in the town of Didouche Mourad which is located 13 km north of Constantine. Samples of air particulate matter were collected at one site located in the heart of the town and situated 3 km north of a cement plant. Samples were collected from 2 November 2002 to 28 April 2003 every 3 days using a high volume air sampler. Sampling intervals were 24 h in all cases. During the same period, samples of dust fallout were collected at the same site. Samples were collected at 30-day intervals. Lead, chromium, manganese, nickel, copper, cobalt and cadmium deposition fluxes were measured and both the soluble and insoluble fractions were determined. Furthermore, the information gathered by this study was correlated with the corresponding hourly weather data provided by a weather station installed at the study station. The possible sources for dust and trace metals were analyzed by comparing average contributions of wind aspects to the concentrations and depositions of mass and chemical species with the average frequencies of wind direction. The mean concentration was 300 μg/m³. The average dust deposition rate through the period of study was 221 mg/(m².day). Results indicate that anthropogenic sources contribute greatly to trace elements. An exposure assessment to the heavy metals taking into account the inhalation route and soil dust ingestion was carried out and allowed direct comparison of trace metal intakes via these routes.     

Atmospheric background trace elements deposition in Tierra del Fuego region (Patagonia,Argentina), using transplanted <Emphasis Type="Italic">Usnea barbata</Emphasis> lichens

Lichen, Usnea barbata, transplants taken from Tierra del Fuego (south Patagonia, Argentina) were tested as potential biomonitors of atmospheric airborne deposition in an apparently pristine environment. In 2005, lichens were sampled in a reference site (n = 31) and transplanted in the northern Region of Tierra del Fuego. After, respectively, 1 month and 1 year of exposure, we collected them. The aim of the study was to determine the bioaccumulation of 26 elements in order to evaluate the background levels in the selected area. Samples were analyzed by the sector field inductively coupled plasma mass spectrometry. Discriminant analysis on principal component analysis factors was applied in order to explore the relationship among the different elements as far as time and spatial variation in transplants regards. The analysis was tested by Monte Carlo test based on 999 replicates. The most important contamination source resulted to be the atmospheric soil particle deposition. Furthermore, the results were compared with those obtained from the lichens collected in central and southern Tierra del Fuego. This study confirms the ability of U. barbata to reflect the background levels of the 26 elements in that environment. Compared with other background sites in the world, we did confirm that Tierra del Fuego lichens have a low content of the studied elements. Tierra del Fuego turned out not to be a pristine environment as supposed, but it can be considered as a reference basal ecosystem for useful comparisons among different geographical areas. These findings can be very relevant and useful for environmental conservation programs.     

Lichen biomonitoring of trace metals in the Pistoia area (central northern Italy)

The epiphytic lichen Parmelia caperata (L.) Ach. was used as bioaccumulator of the heavy metals Cd, Cr, Cu, Hg, Ni, Pb and Zn in the environs of the town of Pistoia (central northern Italy). The concentrations of Cd, Cr, Ni, Hg and Pb were comparable with those found in areas not subject to atmospheric pollution. Copper and especially Zn were found in rather high concentrations. Fertilizers and pesticides were the main source of atmospheric contamination.     

大气颗粒物手工比对监测体系滤膜称量质控技术探讨

健全大气颗粒物手工比对监测体系是"十三五"环境空气自动监测质量管理的一项重点任务,其中颗粒物滤膜的称量直接影响手工监测数据质量。研究调研了国内各级环保部门所属环境监测机构颗粒物滤膜称量工作情况,结合国内外方法标准、技术规范等,重点探讨了称量实验室环境、称量设备、称量影响因素等滤膜称量质控要点,并针对环境管理与监测需求对大气颗粒物手工比对监测滤膜称量质控提出建议。     

The epiphytic lichen hypogymnia physodes as a biomonitor of atmospheric nitrogen and sulphur deposition in Norway

Hypogymnia physodes was sampled from 179 sites of Scots pine forests regularly distributed throughout Norway. The purpose was to map the nitrogen and sulphur contents of lichen thalli on a large-scale geographical basis, and to relate these values to differences in atmospheric deposition and climate.The lichen nitrogen and sulphur concentrations showed large differences; the highest concentration values being 4–5 times greater than the lowest. The highest nitrogen and sulphur values occurred along the coast of southern Norway and on some sites in the inland of southern Norway. There was a close correlation between the two elements. The lichen N/S ratio decreased with increasing latitude.The nitrogen and sulphur contents ofHypogymnia physodes were both significantly correlated to estimated atmospheric deposition of these two elements in Norway. The degree of explanation improved when climatic variables such as temperature sum, altitude, annual precipitation and temperature were included. Factors promoting growth, such as high bark pH, mild winters, hot summers, high precipitation, high ammonium deposition and high evapotranspiration, were all associated with lower lichen nitrogen and/or sulphur concentrations. Unfavourable growth conditions, such as at high altitude, was related to higher concentrations than expected from deposition models. This indicates that differences in element concentration between nearby localities might be related to local differences in climate and lichen growth conditions. This should be taken into consideration whenever using lichens for biomonitoring.     

Using Lichen Chemistry to Assess Airborne Tungsten and Cobalt in Fallon, Nevada

This paper describes the use of lichen chemistry to assess airborne tungsten and cobalt in Fallon, Nevada, where a cluster of childhood leukemia has been on going since 1997. Lichens and their rock substrates were collected from Rattlesnake Hill within Fallon as well as from four different rock outcrops located north, east, south, and west of Fallon and at least 20 km away from the town center. In the lichens themselves, W and Co are significantly higher within Fallon than in the combined control site outside of Fallon. In the rock substrates of the lichens, no differences exist in W and Co. The W and Co differences in lichens cannot be attributed to substrate geochemistry. Fallon is distinctive in west central Nevada for high airborne W and Co, and given its cluster of childhood leukemia, it stands to reason that additional biomedical research is in order to test directly the leukogenicity of combined airborne W and Co.     

Characteristics of Hazardous Airborne Dust Around an Indian Surface Coal Mining Area

Surface coal mining creates more air pollution problems with respect to dust than underground mining . An investigation was conducted to evaluate the characteristics of the airborne dust created by surface coal mining in the Jharia Coalfield. Work zone air quality monitoring was conducted at six locations, and ambient air quality monitoring was conducted at five locations, for a period of 1 year. Total suspended particulate matter (TSP) concentration was found to be as high as 3,723 μg/m³, respirable particulate matter (PM10) 780 μg/m³, and benzene soluble matter was up to 32% in TSP in work zone air. In ambient air, the average maximum level of TSP was 837 μg/m³, PM10 170 μg/m³ and benzene soluble matter was up to 30%. Particle size analysis of TSP revealed that they were more respirable in nature and the median diameter was around 20 μm. Work zone air was found to have higher levels of TSP, PM10 and benzene soluble materials than ambient air. Variations in weight percentages for different size particles are discussed on the basis of mining activities. Anionic concentration in TSP was also determined. This paper concludes that more stringent air quality standards should be adopted for coal mining areas and due consideration should be given on particle size distribution of the air-borne dust while designing control equipment.     

Characterisation of particulate matter on the receptor level in a city environment

Airborne particulate matter (PM) has become one of the dominant pollutants with the increasing material and energy demand due to global economic growth. The main objective of this research is to provide a comprehensive receptor level characterisation of the particulate matter collected in a city environment. Particulate matter samples were collected on Tapered Element Oscillating Microbalance (TEOM) filters from five monitoring sites over a period of 1 year. An Andersen eight-stage cascade impactor was also used to collect airborne PM samples from three other locations to compare with the samples collected by TEOM. All the samples were then subjected to individual particle morphology and chemical composition analysis by SEM/EDS. Bulk chemical composition of the samples were also analysed through ICP–OES. Based on these analyses, possible sources of the PM samples were identified. The results showed that the monitoring sites in residential environments were dominated by transportation-derived particles and other migratory particulates. Monitoring sites near the city centre were dominant by particles from transportation, with biological particles abundant for the site closer to a river. The monitoring station located close to the industrial area, despite only 200 m away from a motorway, has low contribution of non-exhaust particulates from vehicles. Instead, the particulates collected from this site were dominated by industrial sources. An air dispersion modelling package was also used to model the particulate matter dispersion in the city area for the period of sampling. The results from the model showed that the points of high emissions were around industrial areas.     

Metal deposition patterns in central Scotland,as determined by Lichen transplants

Lichen transplants of Hypogymnia physodes were used in a high-density network of sites for collecting airborne metals from the atmosphere in Armadale, a small industrial town in central Scotland. The mapping of the concentrations of various metals revealed a gradient of metal values which decreased outwards from the town's steel foundry. The findings were discussed in the context of a previous epidemiological investigation of lung disease in the town.     

Lichens as a useful mapping tool?—an approach to assess atmospheric N loads in Germany by total N content and stable isotope signature

To assess whether nitrogen (N) content and δ¹⁵N ratios in nitrophytic lichen species (Xanthoria parietina (L.) Th. Fr. (1860) and Physcia spp. (Schreb.) Michaux (1803)) reflect the quantity and quality of atmospheric N loads, 348 lichen samples from 174 sampling grid cells were investigated in the western part of Germany. The analysed lichen N content ranged between 0.98 and 4.28 % and δ¹⁵N ratios between ?15.2 and ?1.3?‰. Based on the N concentrations and the δ¹⁵N ratios of lichens, different landscape categories and coupled N deposition rates could be inferred for different regions of Germany. By analysing environmental variables like altitude, ammonia emission density, livestock unit and different defined deposition types, a direct relationship was found between lichen chemistry and N compounds produced from agricultural activity. The results support the development of a monitoring method which could be used nationally or even internationally to support current N deposition measurements, by providing reliable information on the quantity and quality of N deposition in high N environments.     

Identifying the origin of atmospheric inputs of trace elements in the Prades Mountains (Catalonia) with bryophytes, lichens, and soil monitoring

The biomonitors Hypnum cupressiforme and Xanthoria parietina were used to assess the deposition of trace elements and their possible origin in the Prades Mountains, a protected Mediterranean forest area of NE Spain with several pollution sources nearby. Al, As, Cd, Co, Cu, Cr, Ni, Pb, Sb, Ti, V, and Zn were determined in 16 locations within this protected area. Soil trace element concentrations were also ascertained to calculate enrichment factors (EF) and use them to distinguish airborne from soilborne trace element inputs. In addition, lichen richness was measured to further assess atmospheric pollution. EF demonstrated to be useful not only for the moss but also for the lichen. Cd, Cr, Cu, Ni, and Zn presented values higher than three in both biomonitors. These trace elements were also the main ones emitted by the potential sources of pollutants. The distance between sampling locations and potential pollution sources was correlated with the concentrations of Cu, Sb, and Zn in the moss and with Cr, Ni, and Sb in the lichen. Lichen richness was negatively correlated with lichen Cu, Pb, and V concentrations on dry weight basis. The study reflected the remarkable influence that the pollution sources have on the presence of trace elements and on lichen species community composition in this natural area. The study highlights the value of combining the use of biomonitors, enrichment factors, and lichen diversity for pollution assessment to reach a better overview of both trace elements’ impact and the localization of their sources.     

氯苯类化合物在大气中分布特征探究

建立环境空气和有组织废气排放模拟污染源,以玻璃纤维滤膜+玻璃棉和活性炭为吸附材料采集大气中氯苯类化合物,使用气相色谱法测定各组分,考察氯苯类化合物在大气气相和颗粒物中的分布特征。结果显示,环境空气和固定污染源有组织排放废气中一氯代至四氯代苯类各组分主要分布在大气气相中,颗粒物中少有分布,说明现行环境监测方法以固体吸附剂采集测定大气中的氯苯类化合物可行。     

A Method for Locating Influential Pollution Sources and Estimating Their Contributions

This work develops a source-oriented approach to locate the influential pollution sources and estimate their contributions to pollutant concentrations observed at a receptor site. The domain containing possible influential pollution sources is divided into systematic grid cells, and the influential grid sources are determined based on the locations of the segment endpoints of air trajectories arriving at the receptors. The contribution of each grid source is initially calculated using a formula derived from a Lagrangian box model and including the effects of source emissions, atmospheric dilution, and chemical transformation and deposition. The formula is described in detail in this study. Finally, the average contribution of each grid source is determined based on numerous analyzed events. The proposed approach was used to locate influential pollution sources and determine their contributions to a rural monitoring station during periods of high SO₂ pollution in southern Taiwan. The contributions of sources in various 2 km by 2 km grid cells, five districts, three source categories, 8 industrial areas, and a power plant were evaluated. The results show that the major influential sources were in the northwestern region of south Taiwan, and belonged to three district and point sources. Furthermore, two industrial areas close to the evaluated stations were also very significant, and contributed about 30% of the total pollution.     

Lead,cadmium, arsenic and zinc in the ecosystem surrounding a lead smelter

A lead smelter has been operating at Belledune in the province of New Brunswick, in eastern Canada, since 1966. This paper presents data on the concentrations of the four primary metals emitted from the smelter — lead, cadmium, arsenic and zinc — which were measured in the terrestrial environment near the smelter and the concentrate transport route. Deposition of these metals to the snowpack and the uptake by grass forage are discussed in relation to non-regulatory guidelines, toxicity and atmospheric emissions. A 1992 snowpack transect survey extending 0.5–40 km northwest, southeast and south of the smelter revealed lead concentrations of 2–3193 ppb, cadmium <0.10–49.7 ppb, arsenic <3.0–72.0 ppb, and zinc 3–401 ppb. Deposition estimates within this zone for lead were between 0.046 and 20.1 kg/ha/yr, cadmium <0.007 and 313 g/ha/yr, arsenic <0.016 and 453 g/ha/yr and zinc 0.020 and 2.52 kg/ha/yr. Concentrations of these metals in the snowpack were highest within 3 km of the smelter and were detectable at greater distances SE of the smelter. Lead was dispersed greater distances from the smelter than cadmium or arsenic. Snowpack samples collected within 5–20 m of the railway contained 140–7270 ppb of lead, 0.4–36.9 ppb of cadmium, <3.0–72.0 ppb of arsenic and 41–13100 ppb of zinc. Grass forage sampled within 0.6–16 km of the smelter contained lead 5–152 ppm, cadmium 0.10–4.1 ppm, and zinc 22–154 ppm. Highest concentrations of lead, cadmium and zinc in grass forage were found were found within 2.2 km of the smelter. Grass forage collected within 10–70 m of the railway contained lead 13–288 ppm, cadmium 0.4–1.3 ppm and zinc 98–831 ppm.     

国家大气颗粒物组分监测网的设计发展展望

中国现阶段大气污染呈现以细颗粒物(PM_2.5)及臭氧(O₃)为代表的复合型污染,PM_2.5的二次生成及区域性的大气污染已经成为影响中国环境空气质量的关键因素。笔者分析了中国开展大气颗粒物组分监测网(简称组分网) 监测工作的紧迫需求,梳理了组分监测的工作目标,提出组分网与城市空气质量监测网、背景站监测网、区域站监测网和光化学网等的联合运用,为污染防治提供精准支撑。研究了 组分网的业务组织:分析了目前技术体系存在的不足,提出了亟需开展的技术体系建设内容； 梳理了组分网工作内容、各方职责,提出了形成国家、地方及社会化服务机构联合参与的工作机制； 借鉴美国大气颗粒物化学成分监测网等先进经验,提出了加强科研与业务化的合作发展以及加强人才队伍培训等工作的重要性。总结了 组分网建设面临的重点问题,提出了监测网络发展的建议。