Arrested municipal solid waste incinerator fly ash as a source of heavy metals to the UK environment

Arrested fly ash samples from most currently operating municipal solid waste (MSW) incinerators in the UK have been analysed for a range of elements. Some of the more important heavy metals ranged in concentration as follows: Cd, 21-4646 (median = 271) mg kg(-1); Cu, 296-1307 (642) mg kg(-1); Cr, 44-1328 (574) mg kg(-1); Ni, 45-2204 (74) mg kg(-1); Pb, 447-9704 (4337) mg kg(-1); and Zn, 2285-13,500 (9232) mg kg(-1). These concentrations represent considerable enrichments relative to median UK soil concentrations. Enrichment ratios (defined as median fly ash: median UK soil) were as follows: Mn 1.6; Co 2.6; Ni 3.3; Ba 11; Sr 11; Cr 15; Cu 35; Pb 108; Zn 113; Cd 387. It is estimated that MSW incinerator ash contributes c. 15 t Cd and 241 t Pb to UK landfill sites per annum. These figures compare with previous studies by Hutton & Symon (Hutton, M. & Symon, C. (1986). The quantities of cadmium, lead, mercury and arsenic entering the UK environment from human activities. Sci. Total Environ., 57, 129-50.) which estimated that annual inputs to UK landfills from coal fly ash are c. 60 t Cd and 1270 t Pb. However, it is argued that metals associated with MSW ashes are potentially of greater environmental significance than in coal ashes, because they are much more available and present at much higher concentrations.     

The use of a sequential leaching procedure for assessing the heavy metal leachability in lime waste from the lime kiln at a caustizicing process of a pulp mill

A five-stage sequential leaching procedure was used to fractionate 13 heavy metals (Cd, Cu, Pb, Cr, Zn, Fe, Mn, Al, Ni, Co, As, V, Ba) and sulphur (S) in lime waste from the lime kiln at the causticizing plant of Stora Enso Oyj Veitsiluoto Pulp Mills at Kemi, Northern Finland, into the following fractions: (1) water-soluble fraction (H₂O), (2) exchangeable fraction (CH₃COOH), (3) easily reduced fraction (HONH₃Cl), (4) oxidizable fraction (H₂O₂ + CH₃COONH₄), and (5) residual fraction (HF + HNO₃ + HCl). Although metals were leachable in all fractions, the highest concentrations for most of the metals were observed in the residual fraction (stage 5). It was also notable that the total heavy metal concentrations in lime waste did not exceed the maximal allowable heavy metal concentrations for soil conditioner agents set by the ministry of the Agricultural and Forestry in Finland. The heavy metals concentrations in lime waste were also lower than the maximal allowable heavy metals concentrations of the European Union Directive 86/278/EEC on the protection of environment, and in particular of the soil, when sewage sludge is used in agriculture. The Ca concentration (420 g kg⁻¹; d.w.) was about 262 times higher than the typical value of 1.6 g kg⁻¹ (d.w.) in arable land in Central Finland. However, the concentration Mg (0.2 g kg⁻¹; d.w.) in lime waste was equal to the Mg concentration in arable land in the Central Finland. The lime waste has strongly alkaline pH (12.8) and a neutralizing value (i.e. liming effect) of 47.9% expressed as Ca equivalents (d.w.). This indicates lime waste to be a potential soil conditioner and improvement as well as a pH buffer.     

Heavy metal concentrations in marine molluscs from the Moroccan coastal region

Mussels (Mytilus galloprovincialis), clams (Venerupis decussatus) and oysters (Crassostrea gigas) were sampled seasonally during 2004-2005, from different coastal environments of Morocco in order to measure their accumulated heavy metal concentrations. The concentrations of Hg and Pb were determined by AFS and ICP-MS methods, respectively, whilst the remaining metals (Cd, Cr, Cu, Mn, Zn and Ni) were quantified by AAS. The soft tissue concentrations of the mussels were on average 7.2 mg kg(-1) (Cd), 9.6 mg kg(-1) (Pb), 0.6 mg kg(-1) (Hg), 26.8 mg kg(-1) (Cu), 8.8 mg kg(-1) (Cr), 292 mg kg(-1) (Zn), 20.8 mg kg(-1) (Mn) and 32.8 mg kg(-1) (Ni). The highest tissue heavy metal concentrations were recorded in the south from the industrial area of Jorf Lasfar. The relationships between metal concentration and season in each species showed very similar annual profiles with a peak observed around spring-summer. Statistical analysis indicated that different species showed different bioaccumulation of metals depending on study site and season.     

Concentration and health risk evaluation of heavy metals in market-sold vegetables and fishes based on questionnaires in Beijing,China

Concentrations of heavy metals (As, Cd, Pb, Cu, Ni, Fe, Mn, and Zn) in market vegetables and fishes in Beijing, China, are investigated, and their health risk to local consumers is evaluated by calculating the target hazard quotient (THQ). The heavy metal concentrations in vegetables and fishes ranged from not detectable (ND) to 0.21 mg/kg fresh weight (f.w.) (As), ND to 0.10 mg/kg f.w. (Cd), and n.d to 0.57 mg/kg f.w. (Pb), with average concentrations of 0.17, 0.04, and 0.24 mg/kg f.w., respectively. The measured concentrations of As, Cd, Pb, Cu, Ni, Fe, Mn, and Zn are generally lower than the safety limits given by the Chinese regulation safety and quality standards of agriculture products (GB2762-2012). As, Cd, and Pb contaminations are found in vegetables and fishes. The exceeding standard rates are 19 % for As, 3 % for Cd, and 25 % for Pb. Pb contaminations are found quite focused on the fish samples from traditional agri-product markets. The paper further analyzed the health risk of heavy metals in vegetables and fishes respectively from supermarkets and traditional agri-product markets; the results showed that the fishes of traditional agri-product markets have higher health risk, while the supermarkets have vegetables of higher heavy metal risk, and the supervision should be strengthened in the fish supply channels in traditional agri-product markets.     

Relationship between heavy metals concentrations in egret species,their environment and food chain differences from two Headworks of Pakistan

Concentration of ten metals (Cd, Cr, Co, Cu, Fe, Li, Mn, Ni, Pb and Zn) were analyzed in the egg contents, prey and soil samples of little egret (Egretta garzetta) and cattle egret (Bubulcus ibis) from two Headworks to determine habitat and species-specific differences; to assess the importance of prey and habitat contamination as an exposure source for heavy metals. Concentration of Cu, Mn, Cr and Pb in egg contents, Fe, Co, Cu, Mn, Zn in prey and Fe, Co, Cu, Ni, Li in surface soils were significantly different (P < 0.05). Mean metal concentrations of Cr, Pb and Cd were relatively higher in little egret whereas Cu and Mn were higher in the egg contents of cattle egret. The mean concentrations of Cu, Mn and Zn were higher in prey samples of cattle egrets and Cr, Cd and Pb in prey samples of little egrets. In soil samples collected from little egret heronries metal concentrations were higher except Cu and Ni. Correlation Analysis and Hierarchical Agglomerative Cluster Analysis (HACA) identified relatively similar associations of metals and their source identification. Metals such as Fe, Cu, Mn, and Li were related with geochemical origin from parent rock material as well as anthropogenic input whereas Cr, Cd, Pb, Ni, Co and Zn were associated mostly with anthropogenic activities. The study suggested that eggs are useful bio-monitor of local heavy metal contamination.     

Heavy metals contents in agricultural topsoils in the Ebro basin (Spain). Application of the multivariate geoestatistical methods to study spatial variations

In this work the content of seven heavy metals (Cd, Cr, Cu, Hg, Ni, Pb and Zn) and other parameters (the pH, organic matter, carbonates and granulometric fraction) in agricultural topsoil in the Ebro basin are quantified, based on 624 samples collected according to an 8 by 8 km square mesh. The average concentrations (mg/kg) obtained were: Cd 0.415+/-0.163, Cr 20.27+/-13.21, Cu 17.33+/-14.97, Ni 20.50+/-22.71, Pb 17.54+/-10.41, Zn 17.53+/-24.19 and Hg 35.6+/-42.05 microg/kg. The concentration levels are relatively low in areas of high pH and low organic matter content concentration. The results of factor analysis group Cd, Cu, Hg, Pb and Zn in F1 and Cr y Ni in F2. The spatial heavy metals component maps based on geostatistical analysis, show definite association of these factors with the soil parent material. The local anomalies (found in Cu, Zn and Pb) are attributed to anthropogenic influence.     

Assessment of heavy metal contamination in Hindon River sediments: a chemometric and geochemical approach

The aim of this study was to assess the level of heavy metals (Cd, Cr, Cu, Fe, Mn, Ni, Pb, and Zn) in the surface sediments of the Hindon River, India that receives both treated and untreated municipal and industrial discharges generated in and around Ghaziabad, India. Mean metals concentrations (mg kg⁻¹) were in the range of; Cu: 21.70-280.33, Cd: 0.29-6.29, Fe: 4151.75-17318.75, Zn: 22.22.50-288.29, Ni: 13.90-57.66, Mn: 49.55-516.97, Cr: 17.48-33.70 and Pb: 27.56-313.57 respectively. Chemometric analysis was applied to identify contribution sources by heavy metals while geochemical approaches (enrichment factor and geo-accumulation index) were exploited for the assessment of the enrichment and contamination level of heavy metals in the river sediments. Chemometric analysis suggested anthropic origin of Cu, Cd, Pb, Zn, and Ni while Fe showed lithogenic origin. Mn and Cr was associated and controlled by mixed origin. Geochemical approach confirms the anthropogenic influence of heavy metal pollution in the river sediments. The study suggests that a complementary approach that integrates chemometric analysis, sediment quality criteria, and geochemical investigation should be considered in order to provide a more accurate appraisal of the heavy metal pollution in river sediments. Consequently, it may serve to undertake and design effective strategies and remedial measures to prevent further deterioration of the river ecosystem in future.     

巢湖表层沉积物中重金属的分布特征及其污染评价

以巢湖表层沉积物为研究对象,利用BCR连续提取法研究了沉积物中Cr、Co、Ni、Cu、Cd、Zn、V和Pb等8种重金属元素的分布特征,同时运用潜在风险指数法和地累积指数法综合评价了巢湖沉积物中重金属的生态风险。结果表明,巢湖沉积物中的重金属含量在空间上表现出东西高、中间低的分布特征。巢湖表层沉积物中Cr、Co、Ni、V和Cu 5种重金属都主要以残渣态为主,Zn和Cd主要以弱酸提取态为主,Pb以可还原态为主,同时,Co和Cu 2种元素的可交换态及可还原态含量占有较高比例,具有潜在危害性。相关性分析显示,Cr、Cu、Pb、Ni、Zn和Cd 6种重金属元素的来源和分布可能具有相似性,Co和V 2种重金属元素具有相似的地球化学行为且其主要来源可能与其他几种重金属不同。潜在生态风险指数评价结果表明,巢湖表层沉积物中8种重金属元素构成的生态危害顺序为:Cd>Pb>Co>Cu>Ni>Zn>V>Cr,Cd具有高的生态危害等级,其他7种重金属元素均为低生态危害等级。地累积指数法评价结果表明:巢湖沉积物重金属元素的富集程度为Cd>Zn>Pb>Co>Cu>V>Ni>Cr,Cr属于清洁级别,Co、Cu、V和Ni处于轻度污染水平,Zn和Pb处于偏中度污染,Cd达到了重污染水平。     

Contamination of wild-grown edible mushrooms by heavy metals in a former mercury-mining area

The aim of this study was to evaluate the contamination of six edible wild species of mushrooms (Boletus pulverulentus, Cantharellus cibarius, Lactarius quietus, Macrolepiota procera, Russula xerampelina and Suillus grevillei) by heavy metals (Hg, Cd, Pb, Zn, Cu, Ni, Cr, Co, Mn and Fe). Mushroom samples were collected from sites contaminated by emissions from mining and processing of polymetallic ores in operation during the period 1969–1993 in Rudňany, southeast Slovakia. The four study sites spanned up to a 5-km distance from the emission source. The collected mushroom samples were analyzed using Flame Atomic Absorption Spectrophotometry and/or Flame Atomic Absorption Spectrophotometry with graphite furnace. Mercury, Cd and, in some samples, also Pb present the highest risks in terms of contamination of the food chain following subsequent consumption. The content of two metals in the dry matter (dm) of the mushrooms exceeded the limits set by the European Union (EU; Cd: 0.5 mg/kg dm, Pb: 1.0 mg/kg dm). The highest mean contents of the eight metals recorded for S. grevillei were 52.2, 2.15, 107, 104, 2.27, 2.49, 81.6 and 434 mg/kg dm for Hg, Pb, Zn, Cu, Ni, Cr, Mn and Fe, respectively. The highest content of Cd was recorded in M. procera (3.05 mg/kg dm) and that of Co in L. quietus (0.90 mg/kg dm). The calculated weekly intake for Hg, Pb and Cd shows that regular consumption of mushrooms from the studied area poses risks to human health.     

Heavy metal distribution in marine sediments from the southwest coast of Spain

The latest version (1999) of the BCR-sequential extraction technique was used to determine the distribution of metals (Cu, Zn, Cd, Pb, Fe, Ni, Cr, and Mn) with major sedimentary phases (acid-soluble, reducible, oxidisable and residual) in samples from the southwest coast of Spain. The total metal content was also determined. The results showed that an extensive area along the coast (35 km long), near the joint mouth of the Tinto and Odiel Rivers, contains sediments with high concentrations of metals, with maximums of 649 mg/kg of Zn, 336 mg/kg of Cu, 197 mg/kg of Pb and 2.5 mg/kg of Cd. The values found for Cr, Ni and Mn are comparable to those in unpolluted areas. Based on the chemical distribution of metals, we found that Zn is the most mobile (i.e., it can pass easily into the water under changing environmental conditions). This metal showed the highest percentages in the acid-soluble fraction (the most labile), especially in the central coastal area, where the samples contained over 50% of this element associated with this fraction. This area close to the Tinto and Odiel river mouths also shows a significant increase in the mobility of Cd and Cu. In both cases the amount present in the residual fraction is lower, and the acid-soluble fraction is increased for Cd and the oxidisable fraction for Cu. However, the highest percentages of Fe, Cr and Ni are found in the residual fraction (84%, 89% and 75%, respectively), which implies that these metals are strongly bound to the sediments.     

Level,source identification,and risk analysis of heavy metal in surface sediments from river-lake ecosystems in the Poyang Lake,China

Environmental Science and Pollution Research - The concentrations, sources, and risks of heavy metals (Fe, Al, Mn, Cr, Co, Ni, Cu, Zn, As, Cd, W, Pb, and Tl) in sediments in five river-lake...     

Metal concentrations and mobility in marine sediment and groundwater in coastal reclamation areas: a case study in Shenzhen, China

The concentrations of metals in the buried marine sediment and groundwater were differently affected by land reclamation. Nine metals (V, Cr, Mn, Co, Ni, Cu, Zn, Cd and Pb) in sediment and coastal groundwater from reclamation areas in Shenzhen were examined. The gradually decreased concentrations (V, Cr, Mn, Ni, Cu, Zn) in sediment and relatively higher concentrations (V, Cr, Mn, Co, Ni, Cu and Cd) in groundwater within reclamation areas were observed. The increase of V, Cr, Mn, Ni, Cu and Cd concentrations in groundwater within reclamation areas subsequently after land reclamation should be resulted from the mobilization of these metals accumulated in the sediment. These metals appear to be easily mobilized from solid phase to solution phase after reclamation. The physico-chemical changes such as reduction in pH and salinity in water environment induced by land reclamation appear to be responsible for metal mobility in the sediment-groundwater system.     

Changes in the leachability of metals from dredged canal sediments during drying and oxidation

The behaviour of metals in canal sediments after their disposal to land has important implications for the environmental management of canal dredgings. The leaching behaviour of trace metals was investigated in a laboratory-based experiment using sediment from a canal in the UK (139 mg Zn kg-1dry sediment, 1.1 mg Cd, kg-1dry sediment 31.5 mg Cr kg-1dry sediment, 20.6 mg Cu kg-1dry sediment 48.4 mg Ni kg-1dry sediment, 43.4 mg Pb kg-1dry sediment and 7.6 mg As kg-1dry sediment). The sediment was allowed to dry. Cores (10 cm long) of the drying canal sediment were taken over a period of 12 weeks. A simple water extraction procedure was used to investigate changes in metal leachability at varying depths through the cores. Metal leachability increased over the first five weeks of drying and then subsequently decreased between weeks five and twelve, (e.g. Cd increased from approximately 0.006 to 0.018 mg/kgsediment then decreased to approximately 0.006 mg/kgsediment, Zn increased from approximately 1.5 to 3 mg/kgsediment and then decreased to approximately 1.5 mg/kgsediment). These results were combined with sulphide/sulphate ratios, which showed a decrease as the sediment dried (e.g. at 2-4 cm depth from approximately 1 to 0.49), and BCR sequential extraction data. Most metals (except Cd and As) showed a redistribution from the residual phase into more mobile phases as the sediment dried and oxidised. Metal leachability was strongly correlated with the sulphide/sulphate ratio with leachability normally increasing with decreasing sulphide/sulphate ratio. The combined results were used to infer the likely behaviour of dredged material upon disposal to land.     

Heavy metals in coastal wetland sediments of the Pearl River Estuary, China

Sediment quality in coastal wetlands of the Pearl River Estuary was concerned since the wetlands were used for land reclamation, aquaculture and wildlife protection, and meanwhile served as one of the main ultimate sinks for large amount of heavy metals discharged from the rapidly developing Pearl River Delta. Total concentrations of heavy metal, such as Zn, Ni, Cr, Cu, Pb, and Cd, and their chemical speciation were investigated. Results showed that the sediments were significantly contaminated by Cd, Zn and Ni with concentration ranges of 2.79-4.65, 239.4-345.7 and 24.8-122.1mg/kg, respectively. A major portion (34.6-46.8%) of Pb, Cd, and Zn was strongly associated with exchangeable fractions, while Cu, Ni and Cr were predominantly associated with organic fractions, residual, and Fe-Mn oxide. Cd and Zn would be the main potential risk and the sediment quality is no longer meeting the demand of the current wetland utilization strategies.     

Evaluation of diffusive gradients in thin film (DGT) samplers for measuring contaminants in the Antarctic marine environment

This work has been the first application of DGT samplers for measuring metals in water and sediment porewater in the Antarctic environment, and whilst DGT water sampling was restricted to quantification of Cd, Fe and Ni, preconcentration using Empore chelating disks provided results for an additional nine elements (Sn, Pb, Al, Cr, Mn, Co, Cu, Zn, As). Although higher concentrations were measured for some metals (Cd, Ni, Pb) using the Empore technique, most likely due to particulate-bound or colloidal species becoming entrapped in the Empore chelating disks, heavy metal concentrations in the impacted Brown Bay were found to be comparable with the non-impacted O'Brien Bay. Sediment porewater sampling using DGT also indicated little difference between Brown Bay and O'Brien Bay for many metals (Cd, Al, Cr, Co, Ni, Cu), however, greater amounts of Pb, Mn, Fe and As were accumulated in DGT probes deployed in Brown Bay compared with O'Brien Bay, and a higher accumulation of Sn was observed in Brown Bay inner than any of the other three sites sampled. Comparison of DGT derived porewater concentrations with actual porewater concentrations showed limited resupply of Cd, Pb, Al, Cr, Mn, Co, Ni, Cu, Zn and As from the solid phase to porewater, with these metals appearing to be strongly bound to the sediment, however, resupply of Fe and Sn was apparent. Based upon our observations here, we suggest that Sn, and to a lesser extent Pb, are critical contaminants.     

Analysis of essential and non-essential trace elements in the organs of a mother–fetus pair of spotted seals (Phoca largha) from the Sea of Japan

Environmental Science and Pollution Research - Concentrations of 22 essential and non-essential trace elements (Be, Al, V, Cr, Mn, Fe, Co, Ni, Cu, Zn, As, Se, Mo, Ag, Cd, Sb, Ba, Tl, Pb, Th, U, and...     

Simultaneous mobilization of heavy metals and polychlorinated biphenyl (PCB) compounds from soil with cyclodextrin and EDTA in admixture

This study evaluated the efficacy of a washing process with cyclodextrin in combination with ethylenediaminetetraacetate (EDTA) for the simultaneous mobilization of heavy metals and PCBs from a field contaminated soil. Ultrasonically aided mixing of the field contaminated soil with a combination of cyclodextrin solution (10%, w/v) and a sparing quantity (2 mmol) of EDTA, simultaneously mobilized appreciable quantities of PCBs and much of the analyte metal (Cd, Cr, Cu, Mn, Ni, Pb, Zn) burdens. Relative to the action of individual reagents, a combination of randomly methylated (RAMEB) or hydroxypropyl beta-cyclodextrin (HPCD) with EDTA did not alter the PCB extraction efficiency nor did the presence of cyclodextrin change the efficiency of mobilization of most heavy metals (Al, Cd, Cr, Fe, Mn, Ni, and Zn) but did increase the recovery of Cu and Pb modestly. Three sonication-washes with the same charge of reagents mobilized appreciable quantities of PCBs (40-76%) and quantitatively extracted the labile fraction of Cd, Cu, Mn, and Pb. RAMEB proved to be more efficient than HPCD for PCB extractions. Three successive extractions with a single charge of cyclodextrin mobilized almost as much PCB (RAMEB, 76%; HPCD, 40%) as did the companion extractions that used fresh reagents each time (RAMEB, 78%; HPCD, 42%). Collectively, these studies demonstrated that PCB compounds and selected heavy metals can be co-extracted efficiently from soil with three successive washes with the same washing suspension containing EDTA and cyclodextrin.     

Source identification and risk assessment of heavy metal contaminations in urban soils of Changsha,a mine-impacted city in Southern China

The urban soils suffered seriously from heavy metal pollutions with rapid industrialization and urbanization in China. In this study, 54 urban soil samples were collected from Changsha, a mine-impacted city located in Southern China. The concentrations of heavy metals (As, Cd, Co, Cu, Mn, Ni, Pb, and Zn) were determined by ICP-MS. The pollution sources of heavy metals were discriminated and identified by the combination of multivariate statistical and geostatistical methods. Four main sources were identified according to the results of hierarchical cluster analysis (HCA), principal component analysis (PCA), and spatial distribution patterns. Co and Mn were primarily derived from soil parent material. Cu, Pb, and Zn with significant positive relationships were associated with mining activities and traffic emissions. Cd and Ni might be affected by commercial activities and industrial discharges. As isolated into a single group was considered to have correlation with coal combustion and waste incineration. Risk assessment of heavy metals in urban soils indicated an overall moderate potential ecological risk in the urban region of Changsha.     

A comparative study on metal sorption by brown seaweed

This study compared the sorption of Ag, Cd, Co, Cd, Mn, Ni, Pb and Zn by a Ca-treated Sargassum biomass at pH 5.0, under low and high ionic strength (IS) conditions. The sorption isotherms of As [As(V)] and Cr [Cr(III) and Cr(VI)] were also determined at low IS. The isotherm data for the eight cationic metals and Cr(III) were well fitted by Langmuir equations. Generally, the maximum metal uptake (Umax) followed: Cr(III) > Pb approximately Cu > Ag approximately Zn approximately Cd > Ni approximately Mn approximately Co > Cr(VI) > As(V) at low IS and Pb > Cu > Co > Mn approximately Cd > Zn approximately Ag > Ni at high IS. As(V) did not bind to the seaweed at pH 5.0. The results indicated that sorption of Pb was not affected by the increasing IS, though the percentage of free Pb ions in the water was greatly reduced as predicted by the speciation model. High IS lowered Umax by 10-36% (except Co and Pb), and lowered the affinity constant of the metal by 33-91% for all cationic metals, as compared to low IS. Moreover, the removal efficiency of the cationic metals and Cr decreased exponentially with initial metal concentrations and was lower at high IS. Ion-exchange was the mechanism responsible for the cationic metal sorption onto the seaweed, and Na ion interfered with the cationic metal binding through electrostatic interaction. In conclusion, this study showed the differential binding capacity of the Sargassm biomass for different metals and oxidation states and the differential effects of IS. According to the present results, Sargassum may be considered a good biosorbent for cationic metals (especially Pb) in both low and high-salt containing wastewater.     

Content, distribution and fate of 33 elements in sediments of rivers receiving wastewater in Hanoi, Vietnam

Untreated industrial and domestic wastewater from Hanoi city is discharged into rivers that supply water for various agricultural and aqua-cultural food production systems. The aim of this study was to assess the content, distribution and fate of 33 elements in the sediment and pore water of the main wastewater receiving rivers. The sediment was polluted with potentially toxic elements (PTEs) with maximum concentrations of 73 As, 427 Cd, 281 Cr, 240 Cu, 218 Ni, 363 Pb, 12.5 Sb and 1240 Zn mg kg(-1) d.w. Observed distribution coefficients (log(10) K(d,obs)) were calculated as the ratio between sediment (mg kg(-1) d.w.) and pore water (mg L(-1)) concentrations. Maxima log(10) K(d,obs) were >4.26 Cd, >6.60 Cu, 4.78 Ni, 7.01 Pb and 6.62 Zn. The high values show a strong PTE retention and indicate the importance of both sorption and precipitation as retention mechanisms. Sulphide precipitation was a likely mechanism due to highly reduced conditions.