Emission of heavy metals from animal carcass incinerators in Taiwan

The metal emissions from three incinerators burning different feedstock in Taiwan were characterized in this study. It was found that the Incinerators A and B, treating pig carcasses and animal (including pigs) carcasses, respectively, had much higher metal concentrations in stack flue gases than Incinerator C that combusted medical wastes. However, Incinerator A obtained relative lower metal contents in fly ash and bottom ash than the other two incinerators, mainly because the former used a much lower feedstock rate (although burning at a lower temperature) than the latter. For all the incinerators, (1) Fe, Ni, Pb, and Zn were dominant in both the fly ash and bottom ash while most of the Cd and Pb (more volatile) were present in the fly ash; (2) Fe emission factor was the highest and Zn/Pb/Ni/Cr emission factors were greater than those of Mn/Cd/Cu; (3) the Cu emission factors in bottom ash were relatively higher in comparison with those in fly ash; and (4) indicatory metals were the same (Fe, Zn, Pb, and Cu). The metal emission factors obtained from the livestock incinerators were much higher than those reported from MSW incinerators. Likewise, crematories that burn human cadavers must create similar pollution issues since metal supplements are part of human's normal diets. This causes an environmental concern and this work has important ramifications both in technical and regulatory decisions.     

Extraction of heavy metals from MSW incinerator fly ash using saponins

An extraction process with saponins was evaluated for removing heavy metals from MSW (municipal solid waste) incinerator fly ashes. Two different fly ashes, A and B, were treated on a laboratory scale with three triterpene-glycoside type of saponins, M, Q, and T, in the pH range 4-9. The results were compared with those of the HCI and EDTA treatment. The treatment with saponins extracted 20-45% of Cr from the fly ashes. Saponins were also effective in extracting Cu from fly ash A attaining 50-60% extraction. Saponin T extracted 100% of Pb from fly ash A at pH around 4. The extraction of Zn with the saponin treatment was similar to that of the HCl treatment. Further, Cr, Cu, Pb, and Zn were fractionated by sequential extraction to investigate the effect of saponins on each fraction. Extraction behavior of other elements during the saponin treatment was also studied. The leaching test on the residues received after the saponin treatment showed that the fly ashes were successfully detoxified to meet the landfilling guideline.     

The use of a sequential leaching procedure for heavy metal fractionation in green liquor dregs from a causticizing process at a pulp mill

A five-stage sequential leaching procedure was used to fractionate heavy metals (Cd, Cu, Pb, Cr, Zn, Fe, Mn, Ni, Co, As, V, Ba and Ti) in green liquor dregs into the following fractions: (1) water-soluble fraction (H2O), (2) exchangeable fraction (CH3COOH), (3) easily reduced fraction (HONH3Cl), (4) oxidizable fraction (H2O2 + CH3COONH4), and (5) residual fraction (HF + HNO3 + HCl). The green liquor dregs were derived from a causticizing process at a pulp mill at Kemi, Northern Finland. According to the leaching studies, the leachability of heavy metals in the water-soluble fraction varied between 0.5 and 2 mg kg(-1) expressed on a dry weight (d.w.) basis, indicating relatively low bioavailability of the metals. However, the concentration of Mn (2065 mg kg(-1); d.w.) showed a strong and of Zn (17.6 mg kg(-1); d.w.), Ni (39.7 mg kg(-1); d.w.) and Ba (32.0 mg kg(-1); d.w.) slightly tendency to be extracted in the exchangeable fraction. In addition, Zn, Mn, Ni, Co, V and Ba showed clear leachability in the easily reduced fraction, as well as Cd, Cu, Cr, Zn, Mn, As and Ba in the oxidizable fraction. For Cd, Cu, Cr, Zn, Mn, Ni, Co, Ba and Ti, the sum of leachable heavy metal concentrations in fractions 1-5 agreed relatively well with the "total" heavy metal concentrations. Recoveries of the sum of fractions 1-5 were 84-56% of those obtained by the US EPA method 3052 (i.e. concentrations obtained after microwave oven digestion with a mixture of HF and HNO3).     

Heavy metal concentrations in marine molluscs from the Moroccan coastal region

Mussels (Mytilus galloprovincialis), clams (Venerupis decussatus) and oysters (Crassostrea gigas) were sampled seasonally during 2004-2005, from different coastal environments of Morocco in order to measure their accumulated heavy metal concentrations. The concentrations of Hg and Pb were determined by AFS and ICP-MS methods, respectively, whilst the remaining metals (Cd, Cr, Cu, Mn, Zn and Ni) were quantified by AAS. The soft tissue concentrations of the mussels were on average 7.2 mg kg(-1) (Cd), 9.6 mg kg(-1) (Pb), 0.6 mg kg(-1) (Hg), 26.8 mg kg(-1) (Cu), 8.8 mg kg(-1) (Cr), 292 mg kg(-1) (Zn), 20.8 mg kg(-1) (Mn) and 32.8 mg kg(-1) (Ni). The highest tissue heavy metal concentrations were recorded in the south from the industrial area of Jorf Lasfar. The relationships between metal concentration and season in each species showed very similar annual profiles with a peak observed around spring-summer. Statistical analysis indicated that different species showed different bioaccumulation of metals depending on study site and season.     

Heavy metal leaching from coal fly ash amended container substrates during Syngonium production

Coal fly ash has been proposed to be an alternative to lime amendment and a nutrient source of container substrates for ornamental plant production. A great concern over this proposed beneficial use, however, is the potential contamination of surface and ground water by heavy metals. In this study, three fly ashes collected from Florida, Michigan, and North Carolina and a commercial dolomite were amended in a basal substrate. The formulated substrates were used to produce Syngonium podophyllum Schott 'Berry Allusion' in 15-cm diameter containers in a shaded greenhouse. Leachates from the containers were collected during the entire six months of plant production and analyzed for heavy metal concentrations. There were no detectable As, Cr, Hg, Pb, and Se in the leachates; Cd and Mo were only detected in few leachate samples. The metals constantly detected were Cu, Mn, Ni, and Zn. The total amounts of Cu, Mn, Ni, and Zn leached during the six-month production period were 95, 210, 44, and 337 microg per container, indicating that such amounts in leachates may contribute little to contamination of surface and ground water. In addition, plant growth indices and fresh and dry weights of S. podophyllum 'Berry Allusion' produced from fly ash and dolomite-amended substrates were comparable except for the plants produced from the substrate amended with fly ash collected from Michigan which had reduced growth indices and fresh and dry weights. Thus, selected fly ashes can be alternatives to commercial dolomites as amendments to container substrates for ornamental plant production. The use of fly ashes as container substrate amendments should represent a new market for the beneficial use of this coal combustion byproduct.     

Heavy metals contents in agricultural topsoils in the Ebro basin (Spain). Application of the multivariate geoestatistical methods to study spatial variations

In this work the content of seven heavy metals (Cd, Cr, Cu, Hg, Ni, Pb and Zn) and other parameters (the pH, organic matter, carbonates and granulometric fraction) in agricultural topsoil in the Ebro basin are quantified, based on 624 samples collected according to an 8 by 8 km square mesh. The average concentrations (mg/kg) obtained were: Cd 0.415+/-0.163, Cr 20.27+/-13.21, Cu 17.33+/-14.97, Ni 20.50+/-22.71, Pb 17.54+/-10.41, Zn 17.53+/-24.19 and Hg 35.6+/-42.05 microg/kg. The concentration levels are relatively low in areas of high pH and low organic matter content concentration. The results of factor analysis group Cd, Cu, Hg, Pb and Zn in F1 and Cr y Ni in F2. The spatial heavy metals component maps based on geostatistical analysis, show definite association of these factors with the soil parent material. The local anomalies (found in Cu, Zn and Pb) are attributed to anthropogenic influence.     

SGA对垃圾焚烧飞灰中重金属的固化性能研究简

根据EPA 1311、HJ/T 299-2007、HJ/T 300-2007和HJ 557-2009等国内外不同标准，研究了深圳某垃圾焚烧发电厂垃圾焚烧飞灰的浸出毒性，探讨了六硫代胍基甲酸（sixthio guanidine acid，SGA）、二甲基二硫代氨基甲酸盐（sodium dimethyl dithio carbamate，SDD）和Ca（OH）₂浓度对垃圾焚烧飞灰中重金属的固定性能的影响。研究结果表明，随着浸提液pH的降低，该厂焚烧飞灰中大部分金属元素的浸出量增大，焚烧飞灰浸出液中的Cd、Ni、Pb和Zn浓度分别超过国家危险废物鉴别标准（GB5085.3-2007）规定值的4.75倍、1.47倍、6.72倍和2.20倍，属于危险废弃物，必须进行稳定化处理。当固化剂SGA加入量为0.1 mol/kg时，稳定化后的重金属浸出浓度已经低于危险废物鉴别标准，且对Cd、Cr、Cu和Pb的固化性能优于SDD和Ca（OH）₂；当固化剂SGA、SDD和Ca（OH）₂加入量为0.5 mol/kg时，稳定化后的焚烧飞灰重金属浸出浓度均低于国家危险废物鉴别标准（GB 5085.3-2007）中的规定值。与SDD和Ca（OH）₂相比，SGA对垃圾焚烧飞灰中重金属的固化处理更具有优势。     

SGA对垃圾焚烧飞灰中重金属的固化性能研究

根据EPA1311、HJ／T299—2007、HJ／T300—2007和HJ557—2009等国内外不同标准，研究了深圳某垃圾焚烧发电厂垃圾焚烧飞灰的浸出毒性，探讨了六硫代胍基甲酸（sixthioguanidineacid，SGA）、二甲基二硫代氨基甲酸盐（sodiumdimethyldithiocarbamate，SDD）和Ca（OH）2浓度对垃圾焚烧飞灰中重金属的固定性能的影响。研究结果表明，随着浸提液pH的降低，该厂焚烧飞灰中大部分金属元素的浸出量增大，焚烧飞灰浸出液中的cd、Ni、Ph和zn浓度分别超过国家危险废物鉴别标准（GB5085．3—2007）规定值的4．75倍、1．47倍、6．72倍和2．20倍，属于危险废弃物，必须进行稳定化处理。当固化剂SGA加入量为0．1mol／kg时，稳定化后的重金属浸出浓度已经低于危险废物鉴别标准，且对Cd、Cr、Cu和Pb的固化性能优于SDD和Ca（OH）2；当固化剂SGA、SDD和Ca（OH）2加入量为0．5mol／kg时，稳定化后的焚烧飞灰重金属浸出浓度均低于国家危险废物鉴别标准（GB5085．3-2007）中的规定值。与SDD和Ca（OH）：相比，SGA对垃圾焚烧飞灰中重金属的固化处理更具有优势。     

Heavy metals in coastal wetland sediments of the Pearl River Estuary, China

Sediment quality in coastal wetlands of the Pearl River Estuary was concerned since the wetlands were used for land reclamation, aquaculture and wildlife protection, and meanwhile served as one of the main ultimate sinks for large amount of heavy metals discharged from the rapidly developing Pearl River Delta. Total concentrations of heavy metal, such as Zn, Ni, Cr, Cu, Pb, and Cd, and their chemical speciation were investigated. Results showed that the sediments were significantly contaminated by Cd, Zn and Ni with concentration ranges of 2.79-4.65, 239.4-345.7 and 24.8-122.1mg/kg, respectively. A major portion (34.6-46.8%) of Pb, Cd, and Zn was strongly associated with exchangeable fractions, while Cu, Ni and Cr were predominantly associated with organic fractions, residual, and Fe-Mn oxide. Cd and Zn would be the main potential risk and the sediment quality is no longer meeting the demand of the current wetland utilization strategies.     

Content, distribution and fate of 33 elements in sediments of rivers receiving wastewater in Hanoi, Vietnam

Untreated industrial and domestic wastewater from Hanoi city is discharged into rivers that supply water for various agricultural and aqua-cultural food production systems. The aim of this study was to assess the content, distribution and fate of 33 elements in the sediment and pore water of the main wastewater receiving rivers. The sediment was polluted with potentially toxic elements (PTEs) with maximum concentrations of 73 As, 427 Cd, 281 Cr, 240 Cu, 218 Ni, 363 Pb, 12.5 Sb and 1240 Zn mg kg(-1) d.w. Observed distribution coefficients (log(10) K(d,obs)) were calculated as the ratio between sediment (mg kg(-1) d.w.) and pore water (mg L(-1)) concentrations. Maxima log(10) K(d,obs) were >4.26 Cd, >6.60 Cu, 4.78 Ni, 7.01 Pb and 6.62 Zn. The high values show a strong PTE retention and indicate the importance of both sorption and precipitation as retention mechanisms. Sulphide precipitation was a likely mechanism due to highly reduced conditions.     

The EDTA effect on phytoextraction of single and combined metals-contaminated soils using rainbow pink (Dianthus chinensis)

Rainbow pink (Dianthus chinensis), a potential phytoextraction plant, can accumulate high concentrations of Cd from metal-contaminated soils. The soils used in this study were artificially added with different metals including (1) CK: original soil, (2) Cd-treated soil: 10 mg Cd kg(-1), (3) Zn-treated soil: 100 mg Zn kg(-1), (4) Pb-treated soil: 1000 mg Pb kg(-1), (5) Cd-Zn-treated soil: 10 mg Cd kg(-1) and 100 mg Zn kg(-1), (6) Cd-Pb-treated soil: 10 mg Cd kg(-1) and 1000 mg Pb kg(-1), (7) Zn-Pb-treated soil: 100 mg Zn kg(-1) and 1000 mg Pb kg(-1), and (8) Cd-Zn-Pb-treated soil: 10 mg Cd kg(-1), 100 mg Zn kg(-1), and 1000 mg Pb kg(-1). Three concentrations of 2Na-EDTA solutions (0 (control), 2, and 5 mmol kg(-1) soil) were added to the different metals-treated soils to study the influence of applied EDTA on single and combined metals-contaminated soils phytoextraction using rainbow pink. The results showed that the Cd, Zn, Pb, Fe, or Mn concentrations in different metals-treated soil solutions significantly increased after applying 5 mmol EDTA kg(-1) (p<0.05). The metal concentrations in different metals-treated soils extracted by deionized water also significantly increased after applying 5 mmol EDTA kg(-1) (p<0.05). Because of the high extraction capacity of both 0.005 M DTPA (pH 5.3) and 0.05 M EDTA (pH 7.0), applying EDTA did not significantly increase the Cd, Zn, or Pb concentration in both extracts for most of the treatments. Applying EDTA solutions can significantly increase the Cd and Pb concentrations in the shoots of rainbow pink (p<0.05). However, this was not statistically significant for Zn because of the low Zn concentration added into the contaminated soils. The results from this study indicate that applying 5 mmol EDTA kg(-1) can significantly increase the Cd, Zn, or Pb concentrations both in the soil solution or extracted using deionized water in single or combined metals-contaminated soils, thus increasing the accumulated metals concentrations in rainbow pink shoots. The proposed method worked especially well for Pb (p<0.05). The application of 2 mmol EDTA kg(-1) might too low to enhance the phytoextraction effect when used in silty clay soils.     

Heavy metal contamination in surface sediments of Yangtze River intertidal zone: An assessment from different indexes

Surface sediments (0-5 cm) from 59 stations within the Yangtze River intertidal zone (YRIZ) were sampled for metal contamination analysis in April and August 2005. The concentrations ranged (in mg kg⁻¹ dry weight): Al, 40,803-97,213; Fe, 20,538-49,627; Cd, 0.12-0.75; Cr, 36.9-173; Cu, 6.87-49.7; Mn, 413-1,112; Ni, 17.6-48.0; Pb, 18.3-44.1; and Zn, 47.6-154; respectively. Among the 59 sampling stations, enrichment factors (EF) indicate enrichment of Cd (52 stations), Cr (54 stations), Cu (5 stations), Ni (26 stations), Pb (5 stations) and Zn (5 stations). Geoaccumulation indexes (I_geo) also suggest individual metal contamination in localized areas. This study indicates that Cd, Cr and Ni enrichment in the YRIZ sediment is widespread whereas Cu, Mn, Pb and Zn enrichment is localized or nonexistent. Factor and cluster analyses indicate that Cd is associated with total organic carbon whereas Cu, Cr, Ni, Pb and Zn have a close association with Mn.     

Accumulation of heavy metals in native Andean plants: potential tools for soil phytoremediation in Ancash (Peru)

Metal contamination is a recurring problem in Peru, caused mainly by mine tailings from a past active mining activity. The Ancash region has the largest number of environmental liabilities, which mobilizes high levels of metals and acid drainages into soils and freshwater sources, posing a standing risk on human and environmental health. Native plant species spontaneously growing on naturally acidified soils and acid mine tailings show a unique tolerance to high metal concentrations and are thus potential candidates for soil phytoremediation. However, little is known about their propagation capacity and metal accumulation under controlled conditions. In this study, we aimed at characterizing nine native plant species, previously identified as potential hyperaccumulators, from areas impacted by mine tailings in the Ancash region. Plants were grown on mine soils under greenhouse conditions during 5 months, after which the concentration of Cd, Cu, Ni, Pb, and Zn was analyzed in roots, shoots, and soils. The bioaccumulation (BAF) and translocation factor (TF) were calculated to determine the amount of each metal accumulated in the roots and shoots and to identify which species could be better suited for phytoremediation purposes. Soil samples contained high Cd (6.50–49.80 mg/kg), Cu (159.50–1187.00 mg/kg), Ni (3.50–8.70 mg/kg), Pb (1707.00–4243.00 mg/kg), and Zn (909.00–7100.00 mg/kg) concentrations exceeding national environmental quality standards. After exposure to mine tailings, concentrations of metals in shoots were highest in Werneria nubigena (Cd, 16.68 mg/kg; Cu, 41.36 mg/kg; Ni, 26.85 mg/kg; Zn, 1691.03 mg/kg), Pennisetum clandestinum (Pb, 236.86 mg/kg), and Medicago lupulina (Zn, 1078.10 mg/kg). Metal concentrations in the roots were highest in Juncus bufonius (Cd, 34.34 mg/kg; Cu, 251.07 mg/kg; Ni, 6.60 mg/kg; Pb, 718.44 mg/kg) and M. lupulina (Zn, 2415.73 mg/kg). The greatest BAF was calculated for W. nubigena (Cd, 1.92; Cu, 1.20; Ni, 6.50; Zn, 3.50) and J. bufonius (Ni, 3.02; Zn, 1.30); BCF for Calamagrostis recta (Cd, 1.09; Cu, 1.80; Ni, 1.09), J. bufonius (Cd, 3.91; Cu, 1.79; Ni, 18.36), and Achyrocline alata (Ni, 137; Zn, 1.85); and TF for W. nubigena (Cd, 2.36; Cu, 1.70; Ni, 2.42; Pb, 1.17; Zn, 1.43), A. alata (Cd, 1.14; Pb, 1.94), J. bufonius (Ni, 2.72; Zn, 1.63), and P. clandestinum (Zn, 1.14). Our results suggest that these plant species have a great potential for soil phytoremediation, given their capability to accumulate and transfer metals and their tolerance to highly metal-polluted environments in the Andean region.     

垃圾焚烧重金属迁移特性及其影响因素

综述了城市固体垃圾(MSW)焚烧过程中的Hg、Cd、Pb、Cu、Zn、As和Cr等几种主要重金属污染源在焚烧过程中的迁移特性及其主要影响因素。将重金属在焚烧过程中的迁变归结为:蒸发、气相和表面反应、冷凝成核团聚和飞灰吸附等4个主要过程;而垃圾中重金属的初始浓度、原始垃圾的基体盐分(如A l、S i和K、Na等的存在形式)、垃圾中的C l(PVC和NaC l)和S的含量、垃圾的含水量以及焚烧过程中的运行参数(温度、滞留时间、氧化-还原气氛)等都会对焚烧过程的迁移规律产生影响。     

Characteristics of leachate from pyrolysis residue of sewage sludge

The pyrolysis residue (SP) of sewage sludge (SS) produced at 500 degrees C was subjected to batch and column leaching tests to investigate the release of its organic and inorganic constituents and metals. For comparison, incineration ash (SI) obtained from a SS incinerator was also tested. Pyrolysis and incineration reduced organic matter of SS from 0.78 kg kg(-1)-dry SS to 0.16 and 0.01 kg kg(-1)-dry SS, respectively. Heavy metals remained in SP without being volatilized, although Cd and Pb were transferred into the off-gas during incineration. In the batch leaching test with the leaching liquid-to-solid mass ratio (L/S)=10, the pH of the SS, SP, and SI filtrates was 6.3, 7.9, and 11.0, respectively. The total organic carbon concentrations were in the order SS (877 l mg l(-1))>SP (99 mg l(-1))>SI (26 mg l(-1)). The SP and SI filtrates met the landfill standard for the Cd and Pb concentrations (<0.3 mg l(-1)). In the column tests, although the SP contained more organic matter than that of SI, its carbon discharge into the leachate under aerobic conditions was similar to that of SI under anaerobic conditions. The leaching of heavy metals, such as Cd, Cr, Pb, and Zn, was also suppressed in SP during the active decomposition of organic matter. We demonstrated that pyrolysis reduces the potential release of pollutants from sewage sludge in landfill, making it a promising method of treating sewage sludge before landfilling.     

Metal accumulation in wild plants surrounding mining wastes

Four sites were selected for collection of plants growing on polluted soil developed on tailings from Ag, Au, and Zn mines at the Zacatecas state in Mexico. Trace element concentrations varied between sites, the most polluted area was at El Bote mine near to Zacatecas city. The ranges of total concentration in soil were as follows: Cd 11-47, Ni 19-26, Pb 232-695, Mn 1132-2400, Cu 134-186 and Zn 116-827 mg kg(-1) air-dried soil weight. All soil samples had concentrations above typical values for non-polluted soils from the same soil types (Cd 0.6+/-0.3, Ni 52+/-4, Pb 41+/-3mg kg(-1)). However, for the majority of samples the DTPA-extractable element concentrations were less than 10% of the total. Some of the wild plants are potentially metal tolerant, because they were able to grow in highly polluted substrates. Plant metal analysis revealed that most species did not translocate metals to their aerial parts, therefore they behave as excluder plants. Polygonum aviculare accumulated Zn (9236 mg kg(-1)) at concentrations near to the criteria for hyperaccumulator plants. Jatropha dioica also accumulated high Zn (6249 mg kg(-1)) concentrations.     

Wood pellet fly ash and bottom ash as an effective liming agent and nutrient source for rye grass (Lolium perenne L.) and oats (Avena sativa)

Fly ash (FA) and bottom ash (BA) from a softwood pellet boiler were characterized and evaluated as soil amendments. In a greenhouse study, two plant species (rye grass, Lolium perenne L. and oats, Avena sativa) were grown in three different treatments (1% FA, 1% BA, non-amended control) of a silty loam soil. Total concentrations of plant nutrients Ca, K, Mg, P and Zn in both ashes were elevated compared to conventional wood ash. Concentrations of Cd, Cr, Pb, Se and Zn were found to be elevated in the FA relative to BA and the non-amended soil. At 28 d, oat above-ground biomass was found to be significantly greater in soil amended with FA. Potassium and Mo plant tissue concentrations were significantly increased by addition of either ash, and FA significantly increased Zn tissue concentrations. Cadmium and Hg tissue concentrations were elevated in some cases. As soil amendments, either pellet ash is an effective liming agent and nutrient source, but high concentrations of Cd and Zn in FA may preclude its use as an agricultural soil amendment in some jurisdictions. Lower ash application rates than those used in this study (i.e. <1%) may still provide sufficient nutrients and effective neutralization of soil acidity.     

Dioxins, metals, and fish toxicity in ash residue from space heaters burning used motor oil

Ash residue, generated from burning used motor oil, is a complex and ubiquitous waste stream. Ash samples were collected from space heaters and analyzed for dioxins (N=10), expressed as toxic equivalents (TEQ), and heavy metals (N=9). TEQ averaged 148-164 ng kg(-1) (standard deviation [SD] 385-416 ng kg(-1)), depending on methods used for non-detects (NDs) and toxic equivalency factors (TEFs). It is notable that median TEQ (2.89-3.49 ng kg(-1)) was about 50 fold lower, reflecting the influence of several high end values on the mean. The proportion of NDs among 17 polychlorinated dibenzo-p-dioxins (PCDDs) and polychlorinated dibenzofurans (PCDFs) in each sample averaged 38.2% (range 0-94.1%). Total metals averaged 103,000 mg kg(-1) (SD 26,600 mg kg(-1)), with Zn, Cu, and Pb contributing 89.3%, 6.4%, and 3.0% of the total, respectively. Rainbow trout bioassays resulted in median mortalities of 3.2% and 42.0% (respective SD 25.3% and 43.2%) at ash concentrations of 10 and 100 mg l(-1), respectively. Nominal concentrations of several metals (e.g., Cu, Zn) in the fish bioassay exceeded their reported median lethal concentrations (LC50s) for the test species. Multiple regressions (Bonferroni P<0.05) demonstrated that most of the variance in fish mortality could be accounted for by pH, metals (e.g., As, Cd, Pb), and TEQ. Mean TEQ concentration in used oil ash ranked on the high end of TEQ content in other environmental matrices, including wood ash, cement kiln dust, biosolids, and soils. Overall, these results suggest that suitable disposal methods are needed for ash generated from burning used motor oil.     

Fractionation and extractability of sulfur, iron and trace elements in sulfidic sediments

This study describes iron and sulfur fractionation, and the related extractability of selected trace elements (As, Cd, Cr, Cu, Ni, Pb and Zn) in estuarine sediments. The sediments were sulfidic, with moderately high concentrations of pore-water sulfide (200-600 micromol l(-1)) and acid-volatile sulfide (AVS; 9.9-129 micromol g(-1)). Pyrite-S concentrations increased with depth, with 63-251 micromol g(-1) at site W1 and 312-669 micromol g(-1) at site W2. The degree of sulfidisation was generally high (>80%), indicating that Fe may be limiting pyrite accumulation. The ratios of AVS to pyrite-S increased with sediment depth, as expected for the pyritisation of solid-phase AVS. Cadmium, Pb and Zn extractability in 1M HCl indicated that these elements are not significantly sequestered during pyritisation, whereas sequestration may be important for As, Cu and possibly Ni. Extractability trends for Cr suggest that diagenesis in sulfidic sediments may enhance Cr reactivity. Overall, replacement of AVS by pyrite during diagenesis may enhance the reactivity of Cd, Cr, Pb and Zn, whereas As, Cu and possibly Ni may be rendered less reactive.