SBR分段进水工艺提高污水厂的脱氮效率

研究了SBR分段进水工艺用于污水厂升级改造并提高脱氮效率的方法,通过对昆明某污水厂实际运行工艺的实际调研,决定从运行模式、进水方式和排水比变化三方面用SBR研究影响脱氮效率的因素。结果表明,将原工艺2次搅拌、2次曝气的运行模式改为1次搅拌、1次曝气,会改善原模式下第2次搅拌过程中无反硝化反应的状况,提高系统的总氮去除率;将原工艺连续进水的方式改变为间歇进水,系统的脱氮效率提高了5%以上;分3个阶段研究了排水比在20%~40%之间变化对总氮去除率的影响,每阶段2个反应器的对比实验发现,排水比变大相应的总氮去除率升高,但当排水比为35%和40%时系统出水中会有较高浓度的氨氮,因此,排水比为30%最为合宜。     

硫/沸石固定床去除硝酸盐工艺研究

采用硫/沸石固定床反应器去除水中硝酸盐。实验结果表明，在硫/沸石固定床反应器内通过自养反硝化作用能使水体中硝酸盐得到有效的去除。在硫与沸石的体积比为1∶2，水力停留时间为2 h，进水COD为50 mg/L时，出水硝酸盐去除率可达到95%以上；不外加碳源，总氮的去除率仍可达80%以上；在不投加CaCO₃的情况下，出水pH可始终保持7.0；温度对该反应器硝酸盐的去除率影响不大，进水水温为12℃时总氮（TN）去除率仍可达91.1%。     

污水碳源对复合垂直流-水平流人工湿地脱氮效果的影响

碳源是人工湿地反硝化作用重要的限制因子,提供足够的碳源能够有效地提高湿地系统的反硝化作用,从而提高人工湿地的脱氮效果。考察了以污水碳源作为复合垂直流-水平流人工湿地水平流进水碳源,对系统去氮能力的影响。实验结果显示,添加碳源能使复合人工湿地对TN和氨氮的去除率分别由23.19%、39.57%提高到34.17%和50.4%。当碳源污水(化粪池污水)/硝化处理水(垂直流出水)体积比为1∶4(C/N=1.22∶1)时,系统对氨氮和总氮具有最好的去除效果,且在不同季节具有较强的脱氮稳定性。不同季节加碳源复合系统对氨氮和总氮去除效果差异显著,在夏季去除效果最高可到达66.79%和60.95%。在加污水碳源条件下,增加停留时间对TN去除效果无明显影响,但可以显著提高氨氮去除率;有植物系统比无植物系统去除NH+4-N和TN的效果要好,且夏季提升效果最明显。由此可见,以污水碳源作为复合垂直流-水平流人工湿地系统中水平流部分的碳源,是强化人工湿地脱氮效果的有效手段,但是添加碳源比例、保温措施及植物种植是人工湿地重要的设计参数。     

Fenton氧化-前置反硝化缺氧好氧池(A/O)处理荧光增白剂废水中试研究

采用Fenton氧化-前置反硝化缺氧好氧池(A/O)对荧光增白剂废水IC出水进行中试实验研究。实验表明,在Fe2+投加量为0.003 mol/L,进水pH值为3,[H2O2]/[Fe2+]为4∶1,反应时间为2 h的条件下,Fenton氧化法对COD的去除率可以达到46%以上,出水BOD5/COD的值由0.26提高到0.58。氧化后废水进入前置反硝化生物脱氮系统进行生化处理,该系统采用间歇式进水,水力停留时间为2 d,实验结果表明,A/O系统对COD、氨氮和总氮的去除率分别达41%、90%以上和86%。该组合工艺对COD的总去除率可达到67%,出水氨氮在20 mg/L以下,总氮在37 mg/L以下。     

人工快速渗滤系统微生物生长与分布情况调查研究

以深圳白芒的人工快速渗滤(CRI)系统为研究对象,分析了不同温度下CRI系统中各微生物类群以及脱氮功能菌的生长和分布情况.结果表明,CRI系统对污水处理效果较好,出水SS、BOD5和氨氮的去除率在90％以上,COD的去除率在60％以上.CRI系统以硝化作用为主,有机氮基本转换成硝态氮；而反硝化作用去除总氮的效果不明显.CRI系统的微生物发育良好,有着比较高的生物活性.CRI系统中细菌占有绝对优势,各深度填料中的细菌数量均超过108个/mL,比放线菌、真菌高2～4个数量级；脱氮功能菌中,氨化功能菌的数量最多,其次是亚硝化功能菌、反硝化功能菌,硝化功能菌数量最少.在空间分布上,各微生物类群以及大部分脱氮功能菌(除反硝化功能菌外)都呈现出从填料上层到下层数量逐渐减少的规律.     

生物活性炭填料反应器处理含盐水体的硝化性能

以颗粒活性炭为填料,采用盐度梯度两步驯化法构建含盐水体生物滤器硝化功能,研究了生物滤器稳定后水力停留时间(hydraulic retention time,HRT)、进水氨氮负荷和CODMn/N等对反应器硝化性能的影响。结果表明,25～27℃,盐度30的含盐水体生物滤器硝化功能构建需73 d,其中淡水生物滤器硝化功能构建需28 d,淡水驯化为盐度15的生物滤器需19 d,盐度15驯化为盐度30的生物滤器需26 d;实验条件下生物活性炭填料反应器中生物量达到146～742.1 nmolP/g-BAC;调节进水氨氮浓度2 mg/L左右时,最佳HRT为1 h,氨氮去除率达到84.98%,相应的氨氧化菌和硝酸菌氧吸收速率(oxygen uptake rate,OUR)分别为2.091和1.948 mg O2/(g-BAC.h);HRT为1 h时,随着进水氨氮负荷的加大,氨氮去除率逐渐降低,当进水氨氮负荷由0.12增加到0.48 g-N/(kg-BAC.d)时,氨氮去除率由84.98%降低到41.68%,同时氨氧化菌OUR由2.091降低到0.625 mg O2/(g-BAC.h);随着CODMn/N的升高,氨氮去除率下降,CODMn/N从1～8时,氨氮去除率由84.98%降低到53.64%,CODMn去除率却逐渐增加,由40.86%增加到93.59%,异养菌OUR随着CODMn/N升高呈上升趋势,最大达到0.914 mg O2/(g-BAC.h)。     

两级UASB与好氧组合工艺处理城市生活垃圾渗滤液的启动研究

采用两级UASB与好氧组合工艺处理早期城市生活垃圾渗滤液.系统出水按不同比例回流到一级UASB中进行反硝化,同时进行产甲烷反应,有机物在二级UASB中被进一步降解,好氧池完成剩余有机物的去除和氨氮的硝化.启动阶段通过对原渗滤液不同比例的稀释,分5次逐步提高进水浓度,启动结束时完成了对原渗滤液的高效处理.在进水COD浓度从3000 mg/L提高到15000 mg/L,氨氮浓度从250 mg/L提高到1400 mg/L时,最终COD去除率稳定在92%左右,氨氮去除率可达99%以上,一级UASB中反硝化率接近100%,回流比为300%时系统总氮去除率为70%～80%.     

钢渣-灰岩人工湿地脱除粪便污水高氮素的实验研究

构建小试系统研究了钢渣-灰岩垂直潜流人工湿地对粪便污水中高浓度氮素的降解效果。同时比较分析了填料填铺方式和表层填料对钢渣-灰岩垂直潜流湿地降解粪便污水氮素效能的影响。结果表明：当原水氨氮在42.72～272.60 mg/L，总氮在107.40～689.35 mg/L内，钢渣-灰岩垂直潜流人工湿地出水氨氮和总氮浓度可分别达到13.57 mg/L和62.83 mg/L；从长期效果来看，大级配差的正反粒径混合填铺的填料结构更有利于钢渣-灰岩人工湿地保持氮素降解效能；表层的基质材料选择要充分考虑渗透性和复氧能力；钢渣不但对氨氮有吸附作用，而且为氨氮的挥发和硝化/反硝化作用创造有利环境；灰岩在钢渣协助下溶出钙离子以利于氨氮的阳离子交换，同时为铁自养反硝化菌和脱硫杆菌的自养反硝化作用提供碳源。     

回流式无膜生物阴极微生物燃料电池脱氮

为有效提高脱氮效率、降低MFC运行成本,设计了一种新构型回流式无PEM膜的生物阴极微生物燃料电池,处理生活污水,回收电能。研究了该系统的启动情况及稳定运行时的污水脱氮效果和产电性能。结果表明,系统稳定运行后,输出电压0.53 V,反应器内阻406.8Ω,最大功率密度201.9 mW/m3。连续进水、停留时间12 h、回流比为1及阴极连续曝气条件下,COD去除率85%以上,氨氮去除率93.94%,总氮去除率44.96%,总氮去除较作参比的A2/O系统提高8.17%。     

沸石曝气生物滤池去除氨氮性能及生物学特征分析

天然沸石具有较大的孔隙率和比表面积,对氨氮有较强的选择性离子交换能力.运用天然沸石曝气生物滤池处理城市污水厂二级生化出水,结果表明,曝气生物滤池有良好的去除效果.在气水比为3∶1,水力负荷为1 m/h,温度＞20℃情况下,沸石曝气生物滤池对城市污水厂二级生化出水COD去除率为12.7%,NH3-N去除率为96.6%;试验系统沿程微生物活性和微生物量呈现逐渐下降趋势,而单位生物量的生物活性沿程分布则与此相反;曝气生物滤池对水中污染物的去除主要集中在底部进水端部分,当水流达到距进水端上方105 cm时,曝气生物滤池对水中NH3-N的去除率已达86.8%(占氨氮总去除率的90%),COD的去除率为13.3%(占COD总去除率的67%).     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

不同泥源对厌氧氨氧化反应器启动的影响

采用2套上流式生物膜反应器,分别接种少量厌氧氨氧化污泥和大量硝化污泥,考察其对厌氧氨氧化反应器启动的影响。污泥接种入反应器后,测得接种厌氧氨氧化污泥的反应器(R1)内MLSS为0.22 g/L,另一个反应器(R2)MLSS为2.7 g/L。与直接接种厌氧氨氧化污泥相比,R1经过72 d的运行才显现出厌氧氨氧化特性。经过114 d的培养,前者氮去除速率由0.23 kg/(m3.d)提升到5.29 kg/(m3.d),总氮去除率大于89%;R2的氮去除速率由0.01 kg/(m3.d)提升到1.1 kg/(m3.d),总氮去除率大于84.6%。说明普通污泥启动需要一个较长的筛选过程,直接接种少量的厌氧氨氧化污泥比接种普通的污泥能够更快启动厌氧氨氧化反应器。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

造纸废水混凝处理中SFT助凝替代性研究

中小造纸厂废水处理常用PAC作混凝剂 ,PAM作助凝剂。由于PAM成本很高 ,影响了处理设备的投运率。用超细滑石粉 (SFT)替代PAM助凝 ,与混凝剂PAC配合 ,其混凝处理效果基本相当 ,但是处理成本降低 0 .10元 /m3 。由于SFT属环境无害材料 ,不会给排泥带来二次污染     

红土吸附砷对其动电电位的影响

研究了遵义红土吸附砷对其动电电位的影响 ,从砷酸根浓度和体系pH对红土动电电位影响的角度作了探讨 ,结果表明 ,砷酸根离子浓度越大 ,Zata电位下降幅度越大 ,Zata电位也越低 ;随着体系pH的升高 ,氧化铁胶体动电电位逐渐下降 ,甚至改变了表面电位的符号。由此得出了红土吸附砷属于专性吸附的结论。     

活性炭三维电极法对印染废水的处理研究

对三维电极方法处理印染废水进行了实验研究,初步探讨了活性炭三维电极法处理印染废水的机理,对影响处理效果的各种要素,如反应时间、槽电压和pH值等进行了条件实验,得出了活性炭三维电极法处理印染废水的最佳运行条件为:停留时间120-180 min,槽电压25～30 V,进水pH值6.5～7.5。结果表明,该反应器能有效地降低废水色度,有较高的COD去除效率,并能提高印染废水的可生化性。     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%(质量百分比).反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.     

Evaluation of the presence of drugs of abuse in tap waters

A total of seventy samples of drinking water were tested for non-controlled and illicit drugs. Of these, 43 were from Spanish cities, 15 from seven other European countries, three from Japan and nine from seven different Latin American countries. The most frequently detected compounds were caffeine, nicotine, cotinine, cocaine and its metabolite benzoylecgonine, methadone and its metabolite EDDP. The mean concentrations of non-controlled drugs were: for caffeine 50 and 19 ng L⁻¹, in Spanish and worldwide drinking water respectively and for nicotine 13 and 19 ng L⁻¹. Illicit drugs were sparsely present and usually at ultratrace level (<1 ng L⁻¹). For example, cocaine has mean values of 0.4 (Spain) and 0.3 ng L⁻¹ (worldwide), whereas for benzoylecgonine, these mean values were 0.4 and 1.8 ng L⁻¹, respectively. Higher concentrations of benzoylecgonine were found in Latin American samples (up to 15 ng L⁻¹). No opiates were identified in any sample but the presence of methadone and EDDP was frequently detected. Total mean values for EDDP were 0.4 ng L⁻¹ (Spain) and 0.3 ng L⁻¹ (worldwide). Very few samples tested positive for amphetamines, in line with the reactivity of chlorine with these compounds. No cannabinoids, LSD, ketamine, fentanyl and PCP were detected.     

Visualisation of the complexity of EUSES

The interdependencies of parameters applied in the models of EUSES are visualised in a directed connectivity graph. The parameters (inputs, defaults, state variables, outputs) are represented by boxes (nodes) and their relations by lines (edges). The visualisation, on the one hand, clarifies the complexity of the models in EUSES and, on the other hand, creates an overview and transparency. The parameters’ relations to each other can be recognised faster, and the models can be better understood. The complexity was quantified by the number (variety), kind (substance parameter, physico-chemical parameter, concentration, other parameters), and depth (dimension) of the parameter and the number of relations (connectivity). The variety of EUSES (without the modelsSimple Treat andSimple Box whose interior structure is not documented and without the effect and risk characterisation) amounts to 466, the connectivity to 961, and the maximal dimension is 21.