共查询到18条相似文献,搜索用时 250 毫秒
1.
2.
3.
研究了用各种原始毛坯生产大型厚壁管的工艺过程,分析了工艺参数对被获得制件的质量和金属利用系数的影响。确定了根据钢锭尺寸冷却冲孔钢锭的时间。 相似文献
4.
5.
6.
分析了摩托车后挡泥板的冲孔工艺,着重介绍了摩托车后挡泥板冲孔模的结构。该模具布局合理,结构紧凑,提高了生产效率,降低了生产成本,从而降低了摩托车的造价,提高了摩托车的市场竞争力。 相似文献
7.
介绍了 U 形件侧壁孔的冲模设计,它是与斜契式侧向冲孔完全不同的垂直冲孔方法,一次冲出两侧壁上的孔,既保证了两孔的同轴度,又减少了冲床吨位,提高了劳动生产率。 相似文献
8.
9.
10.
11.
12.
电脑机箱的兼容性和可装配性,一方面要求电脑机箱要因兼容主流型号的电脑主板,而在工艺上作出相应改进;另一方面机箱必须具有良好的尺寸精度,方可保证电脑系统装配可靠和运行正常。介绍了电脑机箱尺寸超差控制的工艺改进,基于内定位的电脑机箱冲压件设计可以确保冲压件质量,并且是工序合理安排的重要保证。 相似文献
13.
14.
15.
提出压力机在传统的冲裁加工中存在的问题,介绍了振动冲裁的机理、特点,并指出振动冲裁的研究是精密冲裁的一个重要发展方向。 相似文献
16.
Rakesh Kumar Pathak A. Ravi Kumar G.K. Ananthasuresh 《Journal of Manufacturing Processes》2013,15(1):108-114
This work demonstrates the feasibility of meso-scale (100 μm to mm) punching of multiple holes of intricate shapes in metals. Analytical modeling, finite element (FE) simulation, and experimentation are used in this work. Two-dimensional FE simulations in ABAQUS were done with an assumed material modeling and plane-strain condition. A known analytical model was used and compared with the ABAQUS simulation results to understand the effects of clearance between the punch and the die. FE simulation in ABAQUS was done for different clearances and corner radii of the punch, die, and holder. To complement modeling with real experiments and for the purpose of comparison, a set of punches and dies were made to punch out a miniature spring-steel gripper. Comparison of compliant grippers made by wire-cut electro discharge machining (EDM) and punching shows that realizing sharp interior and re-entrant corners by punching is not easy to achieve. However, the promise of realizing meso-scale parts with complicated shapes through punching is demonstrated in this work; and further work is identified and some strategies are suggested for improvement. The main contribution of this paper is in adapting the well-established punching and blanking operations to the meso-scale as a viable alternative to making miniature devices currently dominated by lithography-based techniques. 相似文献
17.
18.
采用了ANSYS有限元分析软件对圆锥形薄壁件成形过程进行了数值模拟,分析了冲压过程中两类失效形式产生的原因,并提出了相应的解决办法。 相似文献