阳极溶出伏安法测定水体中痕量Sb^5＋

在ｐＨ３．４，８－羟基喹啉、甲基橙的浓度分别为４３μｍｏｇ／Ｌ、１３μｍｏｌ／Ｌ的０．１ｍｏｌ／Ｌ（ＮＨ４）２ＳＯ４底液中，用阳极溶出伏安法直接测定水体中Ｓｂ＾５＋。其线性范围为０．２６～５．２ｎｍｏｌ／Ｌ，方法的检出限为０．１ｎｍｏｌ／Ｌ；９次重复测定的变异系数为０．８％；回收率为９５．６％～１０４％。大部分常见阳离子不干扰测定。     

苯酚在预活化聚酰胺膜酪氨酸酶生物传感器上的响应特性

研究苯酚在预活化聚酰胺膜酪氨酸酶生物传感器上的响应特性,适量儿茶酚的存在可加快传感器到达恒态的速度。被固定酶的量、活性及传感器的有效面积等是影响检测灵敏度的主要因素。首次采用预活化聚酰胺膜固定酪氨酸酶,并与浸蜡石墨电极组合成酪氨酸酶生物传感器,在温度２５℃电位－０．２００ＶｖｓＳＣＥ,儿茶酚浓度５×１０（－７）ｍｏｌ／Ｌ,底液０．１ｍｏｌ／Ｌ磷酸盐缓冲溶液ｐＨ６．５０下,采用电流法测定苯酚及水样中的酚。酶膜的制备、替换和贮存极为方便,酶膜贮存５个月未见活性下降,有良好的重现性和线性范围２×１０（－７）－１．２５×１０（－５）ｍｏｌ／Ｌ。     

循环水处理的现状及未来发展

化学药剂处理仍是目前循环水处理的主要方法,而不断开发多功能复合药剂、推广应用绿色化学品处理技术、研究成本效益性的产品是未来水处理药剂的发展方向。对于国内水处理厂家,除不断开发新型产品及技术外,还需结合使用配方筛选、分析监测、仪器仪表、计算机应用等现代化自动控制技术。     

不除氧单扫描示波极谱法测定茶叶中钙

研究了在不除氧条件下，用单扫描示波极谱法测定茶叶中钙，在０．０２ｍｏｌ／Ｌ ＫＯＨ体系中，钙－桑色素络合物于－０．７８Ｖ产生一灵敏的极谱峰，峰电流与钙浓度在０．１￣０．８μｇ／ｍＬ之间有良好的线性关系。方法灵敏、准确、简便、选择性好。     

几种化学浸提剂对底泥重金属生物有效部分浸提效果的比较

采用微生态系统生物长期暴露试验,比较５种化学浸提剂对底泥重金属生物有部分的浸提效果。结果表明,０．００５ｍｏｌ／ＬＤＴＰＡ＋０．１ｍｏｌ／Ｌ ＴＥＡ＋０．０１ｍｏＬ ＣａＣｌ２,ｐＨ７．３０是一种适合于食腐屑底栖动物的底泥重金属生物有效部分浸提剂;而０．００５ｍｏｌ／ＬＤＴＰＡ＋１ｍｏｌ／Ｌ ＮＨ４ＨＣＯ３．ｐＨ７．６８则一种适合于滤食性动物和水生根系植物底泥重金属生物有效部分浸提剂。     

三氯乙烯在TiO2上光降解反应动力学

设计了新型气固相间歇循环式光催化反应器，选取三氯乙烯为污染物的工作系统进行气固相光催化反应研究．结果表明，在反应器内循环气流量大于３１０ｍＬ／ｍｉｎ时，消除了扩散的影响．当催化剂表面紫外光辐射强度小于０．５ｍＷ／ｃｍ~２和三氯乙烯浓度大于６７μｍｏｌ／Ｌ时．反应处于光子传递控制，光催化反应动力学方程为：ｒ_（ｏｖｅｒａｌｌ）＝１．０８　Ｉ_０．当催化剂表面紫外光辐射强度在０．５－２．０ｍＷ／ｃｍ~２和三氯乙烯初始浓度小于２５．００μｍｏｌ／Ｌ时，反应动力学完全符合Ｌａｎｇｍｕｉｒ－Ｈｉｎｓｈｅｌｗｏｏｄ动力学方程；在紫外光辐射强度大于５ｍＷ／ｃｍ~２和三氯乙烯浓度小于５．２０μｍｏｌ／Ｌ时，光催化反应速率与光强无关，与反应物浓度成正比．光催化反应处于表面作用控制．     

离子色谱法测定酸雨中6种阴离子

离子色谱法测定酸雨中６种阴离子，以流速为１．５１ｍＬ／ｍｉｎ，０．２４ｍｏｌ／Ｌ Ｎａ２ＣＯ３和０．３ｍｏｌ／Ｌ ＮａＨＣＯ３的混和液为淋洗液，在ＹＳＡ８型８００１Ａ－４阴离子交换柱上分离，ＹＳ－１抑制器，ＹＩＣ－８型离子色谱仪电导检测器检测，方法的线性范围均为１００倍，可达２００倍以上，以ＣＩ＾－为例，最小检出限为０．００１，重现性ＣＶ％为０．７６，空白检测偏差Ｓｗｂ＝０．００６８１，回收率为９     

聚合硫酸铁处理镍电解废水

采用聚合硫酸铁－中和法处理镍电解废水，根据正交设计实验，得出最佳工艺条件为：ｐＨ值９．０，聚合硫酸用量为镍含量的２倍，聚丙烯酰胺用量为４ｍｇ／Ｌ，反应为常温，测定时间为２～３ｍｉｎ。处理后水镍残余浓度〈０．１３ｍｇ／Ｌ，钴〈０．０１ｍｇ／Ｌ，铜〈０．００５ｍｇ／Ｌ，ＣＯＤｃｒ〈７０ｍｇ／Ｌ，沉淀时间为２～３ｍｉｎ。     

电凝聚电解电压计算

通过理论分析与实验，分别导出适用于铁板与铝板作电极的电凝聚器的电解电压计算公式，铁电极为Ｕ０＝（ｄ／Ｋ＋０．０４）ｉ＋０．４铝电极为Ｕ０＝（ｄ／ｋ＋０．０４）ｉ＋１．０。     

含取代苯胺类化合物工业废水的电解处理研究

在酸性条件下投加ＮａＣｌ对含取代基团的苯胺类废水，进行了电解和过滤循环的处理。对含氯苯胺、硝基苯胺、甲苯胺等１２种废水进行处理试验，结果表明，在实验条件下电解１．０～２．０ｈ后，含１０００ｍｇ／Ｌ左右的苯胺类废水的出水ＣＯＤｃｒ＜２５０ｍｇ／Ｌ，芳胺含量＜３ｍｇ／Ｌ。采用质谱法分析了部分芳胺的电解固体产物，并对反应机理进行了探讨。     

Double catholyte electrochemical approach for preparing ferratealuminum：a compound oxidant—coagulant for water purification

Ferrate is an excellent water treatment agent for its multi-functions in oxidation,disinfection,coagulation and adsorption,but its coagulation ability depends on its dosage and is after its oxidation.This paper focuses on preparing a new kind of ferrate combined with alum to enhance its coagulation function for water purification.An effective electrolysis reactor was designed and employed in the test.Some key parameters in the process of electrolysis concerning the prepar\ation efficiency,such as the current density,temperature and alkalinity were also investigated.The proper conditions for ferrate-alum preparation were determined.Under the condition of 5V given voltage,6h electrolyzing interval,below 2% alum concentration (in weight),a combined liquid ferrate-alum products was successfully prepared,which contained 0.0294 mol/L FeO4^2- and 0.0302 mol/L total soluble ferron with 2% Al2O3.There was no insoluble ferron produced by controlling an optimum electrochemical condition.     

Double catholyte electrochemical approach for preparing ferrate-aluminum: a compound dxidant-coagulant for water purification

Ferrate is an excellent water treatment agent for its multi-functions in oxidation, disinfection, coagulation and adsorption, but its coagulation ability depends on its dosage and is after its oxidation. This paper focuses on preparing a new kind of ferrate combined with alum to enhance its coagulation function for water purification. An effective electrolysis reactor was designed and employed in the test. Some key parameters in the process of electrolysis concerning the preparation efficiency, such as the current density, temperature and alkalinity were also investigated. The proper conditions for ferrate-alum preparation were determined. In the condition of 5V given voltage, 6h electrolyzing interval, below 2% alum concentration (in weight), a combined liquid ferrate-alum products was successfully prepared, which contained 0.0294 mol/L FeO_{4/sub>^2-, 0.0302 mol/L total soluble ferron with 2% Al2O3. There was no insoluble ferron produced by controlling an optimum electrochemical condition.}     

高铁-光催化氧化协同去除藻毒素的研究

研究了高铁-光催化氧化体系去除水中藻毒素的效能.结果表明,通过投加10mg/L的高铁到光催化体系中,由于高铁的强氧化性及其还原产物可作为电子捕获剂的特点,可将光催化效率从63%提高到100%,实现快速完全去除藻毒素的目的.同时对照研究了高铁、光催化、Fe³⁺-光催化、高铁-光催化4种不同反应体系对藻毒素去除的效能.结果显示,单纯的高铁或光催化都可以降解一部分藻毒素,但去除率低,分别为54%和63%,且需大剂量的高铁投加或大大延长光照时间.而在Fe³⁺-光催化、高铁-光催化体系中,只需投加10mg/L的三价铁或高铁,就可以将藻毒素去除率提高到73%和100%,但采用高铁协同光催化体系比三价铁协同光催化体系更有效.也就是说在本体系中,高铁具有十分重要的作用,明显存在着高铁与TiO₂光催化的协同效应.     

高铁酸钾调理改善活性污泥脱水性能的反应机制研究

研究了高铁酸钾(K_2FeO_4)对处理活性污泥脱水性的效果,重点考察了不同pH和剂量条件下,K_2FeO_4调理对污泥过滤脱水特性和胞外聚合物(EPS)分布和组成的影响,以深入认识K_2FeO_4调理污泥的反应机制.研究表明,K_2FeO_4调理效果随pH值的降低而改善,其不仅有氧化裂解作用导致结合型EPS(BEPS)释放,同时其还原产物三价铁离子兼具混凝功效,能够通过电中和与界面吸附去除部分溶解性EPS(SEPS),同时压缩EPS结构,增强污泥絮体结构.此外,当pH值为3,K_2FeO_4投加量为0.1 g·g~(-1)(以TSS计)时,污泥过滤脱水速率和程度均达到最佳.过量投加K_2FeO_4(0.2 g·g~(-1),以TSS计)后,BEPS大量释放,污泥过滤阻力增加,脱水性能恶化.     

Preparation of high concentration polyaluminum chloride with high content of Alb or Alc

A novel membrane distillation concentration method was used to prepare high concentration polyaluminum chloride (PACl) with high content of Al_b or Al_c. 2.52 mol/L PACl₁ with 88% Al_b and 2.38 mol/L PACl₂ with 61% Al_c were successfully prepared. Three coagulants, AlCl₃, PACl₁ and PACl₂ were investigated on their hydrolysis behavior and speciation under different conditions. The effects of pH and dilution ratio on Al species distribution were investigated by ferron assay. Experimental result showed that pH had a significant effect on Al species distribution for the three coagulants. Dilution ratio had little effects on Al_b and Al_c distribution in whole dilution process except the beginning for PACl₁ and PACl₂. The results indicated that transformation of Al depends largely on their original composition. AlCl₃ was the most unstable coagulant among these three coagulants during hydrolysis process. PACl₁ and PACl₂ with significant amounts of highly charged and stable polynuclear aluminum hydrolysis products were less affected by the hydrolysis conditions and could maintain high speciation stability under various conditions.     

超声强化金刚石膜电极电化学降解效率的机制

从电化学氧化的传质过程、吸附与脱附、电极反应3个步骤,考察了超声强化金刚石膜电极(BDD)电化学降解效率的机制.超声对上述3个步骤都有显著影响.超声增强了污染物的传质过程,苯酚和邻苯二甲酸的传质系数分别由5.4×10-6m/s和6.7×10-6m/s增大至2.0×10-5m/s,提高了270%和199%.污染物在BDD电极表面的电化学吸附特性决定了超声对吸附与脱附过程的作用.苯酚的吸附量大,但中间产物难于脱附,超声虽然使得吸附量由6.49×10-10mol/cm2减小至1.39x10-10mol/cm2,但促进了产物的脱附,产生了正效应,有利于直接氧化,氧化峰电流提高了32%;邻苯二甲酸的吸附能力弱,超声使得吸附量由1.25×10-11mol/cm2进一步减小至3.11×10-12mol/cm2,产生了负效应,导致直接氧化消失.超声可以显著提高BDD电极的降解效率,而且对苯酚降解的促进作用更为明显.苯酚的平均电化学氧化能量利用率提高了287%,高于邻苯二甲酸的224%,这主要是因为超声可以同时强化苯酚的直接氧化和间接氧化,但对于邻苯二甲酸,间接氧化得到了加强,却不发生直接氧化.     

高铁酸钾-微波耦合对印染污泥脱水性能的影响研究

分别采用微波、微波耦合高铁酸钾对印染污泥进行脱水预处理.结果表明,适宜的微波辐射可改善污泥脱水性能.2320、3240、4000 W·L-1对应的最适时间分别是140 s、100 s和80 s.在3240 W·L-1的微波下辐射100 s后,污泥的沉降速率(SV30)、污泥比阻(SRF)和粘度较原污泥分别减少4.00%、18.89%、35.05%.同时,高铁酸钾的加入能更好地提高污泥脱水性能,其最佳投加量为0.1767 g·g-1(以SS计,下同),对应的污泥SV30、毛细吸水时间(CST)、粘度相比原污泥分别降低了13.50%、51.18%、40.79%.泥饼含固率相比原污泥则增加14.58%.微波耦合高铁酸钾能有效破坏污泥絮体结构.随着高铁酸钾投量增加,上清液的蛋白质含量持续增加,多糖含量则先增加后减少.     

电-Fenton法降解低含盐量反渗透浓缩液中腐植酸

为研究采用碳毡-Pt电-Fenton体系处理模拟低含盐量反渗透浓缩液中的腐植酸的影响因素和降解机制,通过单因素试验,以COD_Cr去除率为评价指标,以Fe2+添加量、通氧量、电流密度、pH为考察因素,探讨了不同条件对电-Fenton体系ρ（H₂O₂）和COD_Cr去除率的影响.结果表明:采用电-Fenton法降解模拟反渗透浓缩液,较低的含盐量有助于COD_Cr的去除,与高含盐量（1 000~2 000 mg/L）相比,在低含盐量（500~1 000 mg/L）条件下COD_Cr去除率提高10%~20%;并且最佳条件下实际电流效率（GCE）达到15.6%,电化学能耗为32 kW·h/kg.最佳反应条件:通氧量为0.3 m3/L,Fe2+添加量为0.1 mmol/L,电流密度为3.5 mA/cm2,pH=3,在该条件下反应180 min时,电-Fenton体系产生的ρ（H₂O₂）为105 mg/L,可使ρ（COD_Cr）由150 mg/L降至16 mg/L,COD_Cr去除率达到90%.研究显示,较宽的pH范围（3~7）内碳毡-Pt电-Fenton体系对腐植酸的降解表现稳定,COD_Cr去除率均达到60%以上.      

高铁酸盐对藻类肝毒素的降解

研究高铁酸盐对悦目颤藻(Oscillatoria amoena)肝毒素(Microcystin-LR)的降解效能及其与pH的关系. 结果表明,处理有机质含量很高的藻类肝毒素粗提液,当高铁投加量增到40mg/L,pH控制在6～10,肝毒素几乎被完全降解.同时高铁的还原产物Fe³⁺、Fe(OH)₃发挥其助凝、絮凝的作用,对水体中有机质吸附沉降去除,TOC去除率达到50%左右,铁几乎无残留.高效液相色谱分析发现,作用机制可能是高铁氧化或异构化Adda基团的共轭双键,使Adda基团的结构发生变化,从而降低其毒性.     

Optimum conditions for the formation of Al13 polymer and active chlorine in electrolysis process with Ti/RuO2-TiO2 anodes

A polyaluminum containing a high concentration of Al₁₃ polymer and active chlorine (PACC) was successfully synthesized by a new electrochemical reactor using Ti/RuO₂-TiO₂ anodes. PACC can potentially be used as a dual-function chemical reagent for water treatment. The obtained results indicated that the formation of Al₁₃ polymer and active chlorine, were the most active components in PACC responsible for coagulation and disinfection respectively. These components were significantly influenced by electrolyte temperature, current density, and stirring rate. It was observed that high electrolyte temperature favored the formation of Al₁₃. Increasing current density and stirring rate resulted in high current efficiency of chlorine evolution, thus favoring the generation of Al₁₃ and active chlorine in PACC. When the PACC (Al_T = 0.5 mol/L, basicity = 2.3) was prepared at the optimum conditions by electrolysis process, the Al₁₃ polymer and active chlorine in product reached above 70% of Al_T and 4000 mg/L, respectively. In the pilot scale experiment with raw polyaluminum chloride used as an electrolyte, PACC was successfully prepared and produced a high content of Al₁₃ and active chlorine products. The pilot scale experiment demonstrated a potential industrial approach of PACC preparation.