一种新防腐体系应用于湿烟囱的可行性探讨

介绍了湿法脱硫后烟气的特点及腐蚀性,通过试验验证讨论了XD005防腐体系应用于湿烟囱内壁防腐的技术可行性.     

宁海发电厂脱硫除雾器运行优化及防堵措施

分析了国华宁海发电厂600MW机组WFGD系统除雾器的应用环境及结构原理，提出了运行过程中除雾器优化方式以及防堵塞措施，为其他火电厂湿法脱硫系统解决同类问题提供参考。     

70 kt/a硫磺生产装置除尘系统的设计与研究

概述了硫磺粉尘回收系统的研究现状，简要介绍了一套较为成功的设计方案和几个关键设计环节，指出院 今后推广应用的研究重点和发展趋势，该设计方案突出的特点为：防爆性能好的高效多管式旋风除尘器的设计，对管网和排风罩的优化防爆设计，多层次的防爆抑爆设施的设计。     

海水法烟气脱硫系统检修管理整体设计研究

“十一五”期间,随着节能减排的需要,海水法烟气脱硫工艺(海水脱硫)在我国沿海电厂得到了迅猛发展.针对火电厂海水脱硫检修的管理实践及研究,创造性提出火电厂海水脱硫检修管理的整体设计方案,并对检修周期、检修项目、主要设备的检修工艺及质量标准要求等做出了相应说明.海水脱硫系统检修标准化管理,对提高我国“十二五”期间及以后海水脱硫设备安全、稳定、经济运行具有一定指导借鉴意义.     

火电厂降低PM2.5排放措施研究

简要介绍了几种新型实用的火电厂降低PM2.5排放的控制技术，为火电厂最大限度的降低PM2.5排放提供系统的设计方案。     

火电厂湿法脱硫系统中pH计及密度计的设计应用

针对火电厂湿法烟气脱硫系统中传统pH计及密度计的探头结垢磨损及测量管路堵塞频繁,导致pH和密度的测量出现偏差甚至数据失真这一问题,结合山西大土河焦化有限责任公司热电一分厂3×75t/h循环流化床锅炉烟气脱硫工程实例,着重介绍了改进型pH计的有效防堵塞安装方法及隔膜压力变送器代替传统密度计的设计原理及应用情况,为今后工程实践提供参考。     

湿式静电除尘器流场的数值模拟与优化设计

湿式静电除尘器流场的分布对烟气深度净化具有重要意义，采用CFD数值模拟方法对某项目600MW燃煤发电机组湿式静电除尘器的内部流场设计进行了研究分析。结果表明，流量分配和气流整流是内部流场的两个关键设计要点。有关流量分配的设计需在确保各电场流量分配均匀的同时不明显增加烟风系统阻力，而气流整流的设计方案可同时运用气流均布板和整流格栅，此设计方案不仅可降低整套整流方案的压损，还有利于整流方案的标准化设计和现场优化调整，提高装置可靠性。     

真空断路器的过电压及其防护

在10kV及以下电压等级配电网络中,真空断路器已取代油断路器,在无油化改造过程发挥了积极作用.与油断路器相比,真空断路器具有适合频繁操作,电寿命长,检修维护工作量小,防燃、防爆,运行可靠性高等优点.但在开断交流小电流时会出现过电压现象,阐述了过电压的产生,危害及其防护措施.     

燃煤电厂汞减排技术研究

介绍了燃煤电厂汞的3种排放形态,分析了燃煤电厂汞减排技术,如燃烧添加剂技术、吸收剂喷射技术、稳定剂固汞防溢技术、络合剂絮凝脱汞技术等。在此基础上提出了燃煤电厂汞减排技术选择影响因素,即燃煤煤质、运行工况、脱汞后副产物等,为我国电力行业汞污染控制及减排提供了参考。     

2019中国循环经济发展论坛在南京召开

<正>2019年10月20日,由中国循环经济协会主办的2019中国循环经济发展论坛(以下简称论坛)在南京召开。本届论坛以"壮大绿色产业助力污防攻坚"为主题来自国内外循环经济领域的各界代表齐聚一堂共同研讨发展循环经济、壮大绿色产业、助力污防攻坚的对策措施。来自地方发改、工信、园区管委会、相关行业协会、大专院校、研究机构、国际NGO组织、会员单位和     

1000MW机组电除尘器的设计及技术改进

介绍了1000MW机组电除尘工程的特点及其电除尘器的设计难点，针对1000MW机组电除尘器设计中的诸多不利因素提出了具体的改进措施。     

防风抑尘网设计要点及参数的确定

介绍了堆场起尘、防风抑尘网抑尘的机理和国内外防风抑尘网研究结果,结合实际工程设计的经验,分析了防风抑尘网设计要点和主要参数,提出防风抑尘网设计的意见和建议。     

600MW燃煤机组SCR脱硝工程设计特点

介绍了我国第一批烟气脱硝工程之一——山西阳城电厂600MW燃煤机组SCR工程的设计特点，包括反应器本体设计、催化剂选型设计和氨区设计等。结合实践经验，对脱硝系统设计提出了一些优化建议。     

提高火电厂设计和校核煤质重要性的几点认识

分析锅炉设计煤质在电厂建设各方面的重要性，阐述了燃用煤质偏离设计要求对火电厂安全、经济运行的影响。结合工程实际分析燃用煤质偏离设计煤质的原因，并提出了解决措施。     

基于参数化模型优化的喷氨格栅设计方法研究

从喷氨格栅工程设计要求出发,结合数值模拟分析、代理模型技术以及优化设计方法,提出了一套基于参数化模型优化的喷氨格栅设计方法和流程。该方法从工程设计要求的分析入手,根据喷氨格栅几何参数对喷氨特性的影响特点和规律,建立参数化设计数学模型,并通过优化计算最终获得喷氨格栅的最优设计。另外,通过实例计算验证了该设计方法在SCR脱硝系统喷氨格栅设计中的适用性。     

大港油田污水回用工程超滤反渗透设计

通过总结大港油田污水回用深度处理工程超滤反渗透系统设计思路,介绍了目前国际领先的"双膜法"污水回用深度处理技术.着重论述了该工程超滤反渗透单元以及各辅助系统如加药、反洗、化学清洗等系统的设计,研究并探讨了系统设计中膜污染问题的解决措施和思路.     

干法烟气脱硫电除尘器进口喇叭的设计与应用

电除尘器进口喇叭的设计直接影响其气流均布。针对CFB—FGD干法烟气脱硫后的烟气特点，分析了处理脱硫后烟气的电除尘器进口喇叭设计，进行了气流分布试验，为高烟尘电除尘器进口喇叭的设计提供参考。     

Steady-state design of vertical wells for liquids addition at bioreactor landfills

The rate at which liquids can be added to a vertical well, the lateral zone of impact of the well, and the liquids volume needed to wet the waste within the zone of impact of the well are the key inputs needed to design a vertical well system. This paper presents design charts that can be used to estimate these inputs as a function of municipal solid waste properties (porosity, hydraulic conductivity, and anisotropy ratio), well dimensions (radius and screen length), and injection pressure. SEEP/W modeling was conducted to estimate the key design inputs for a range of conditions practically encountered for a vertical well installed in landfilled waste. The flow rate, lateral zone of impact of a well, liquids volume added, and injection pressure were normalized with the waste properties and well dimensions to formulate dimensionless variables. A series of design charts were created to present dimensionless steady-state flow rate, lateral zone of impact, and the dimensionless liquid volume needed to reach a steady-state condition, as a function of dimensionless input variables. By using dimensionless variables formulated for this work, these charts permit the user to estimate the steady-state design variables described above for a wide range of configurations and conditions beyond those simulated without the need for further modeling. The results of the study suggest that the lateral extent of the well can be estimated using Darcy’s equation and assuming saturated unit-gradient vertical flow regime below the well bottom. An example problem is presented to illustrate the use of the design charts. The scenario described in the example problem was also modeled with SEEP/W, and the results were compared with those obtained from the design charts to demonstrate the validity of design charts for scenarios other than those used for the development of the design charts. The methodology presented in this paper should be thought of as a means to provide a set of bounds that an engineer can use along with their judgment in the design of a system for a specific site.     

超滤膜处理火电厂废水的工业性试验研究

结合现场中试探讨了超滤作为反渗透预处理工艺的可行性，确定了超滤工艺处理某火电厂废水的基本参数，研究了超滤膜的恢复及效果，并且提出了系统设计的相关建议，对工业系统设计具有指导意义。     

EFFECT OF DESIGN VARIABLES ON PARTICIPATION IN RESIDENTIAL CURBSIDE RECYCLING PROGRAMS

This research examines how each of the design variables associated with the design of residential curbside recycling programs affects the participation rate, as well as the effect of interactions between the variables. The evaluation of each design variable includes a literature review and an analysis of the results of six published surveys of curbside recycling programs. The results of this research show that there is no single ideal design for residential curbside recycling programs, but that a variety of combinations of design variables have proven to be successful. This suggests that when designing a recycling program, the costs, needs and goals of the community should be significant factors while taking into consideration the effect of some design variable options on participation. Based on these results, four residential curbside recycling programs were designed: two to maximize participation rates without significant regard to cost; and the other two with the goal of achieving a balance between participation rate and program cost.