Investigation of 1,4-dioxane originating from incineration residues produced by incineration of municipal solid waste

As a groundwater contaminant, 1,4-dioxane is of considerable concern because of its toxicity, refractory nature to degradation, and rapid migration within an aquifer. Although landfill leachate has been reported to contain significant levels of 1,4-dioxane, the origin of 1,4-dioxane in leachate has not been clarified until now. In this study, the origins of 1,4-dioxane in landfill leachate were investigated at 38 landfill sites and three incineration plants in Japan. Extremely high levels of 1,4-dioxane 89 and 340 microg l(-1), were detected in leachate from two of the landfill sites sampled. Assessments of leachate and measurement of 1,4-dioxane in incineration residues revealed the most likely source of 1,4-dioxane in the leachate to be the fly ash produced by municipal solid waste incinerators. Effective removal of 1,4-dioxane in leachate from fly ash was achieved using heating dechlorination systems. Rapid leaching of 1,4-dioxane observed from fly ash in a sequential batch extraction indicated that the incorporation of a waste washing process could also be effective for the removal of 1,4-dioxane in fly ash.     

Limitations of the toxicity characteristic leaching procedure for providing a conservative estimate of landfilled municipal solid waste incineration ash leaching

Limitations of the toxicity characteristic leaching procedure (TCLP) for simulating pollutant leaching from wastes disposed of in full-scale landfills are well understood in the waste management profession; the TCLP solution has a lower pH and greater organic acid content than typical landfill leachate. The TCLP serves its intended regulatory objective, however, as long as a conservative estimate of leaching is provided. Here, we examine TCLP’s ability to represent worst-case leaching conditions for monofilled municipal solid waste incineration (MSWI) ash. A critical examination of TCLP’s applicability to MSWI ash is especially relevant, as ash management at MSWI facilities often centers on passing TCLP, regardless of environmental risk posed by the ash or its recyclability. Multiple batch leaching tests were conducted on different MSWI ash streams: mixed ash, fly ash, and different size fractions of bottom ash. Batch-test results were compared with leachate simulating MSWI ash monofills. The TCLP did not consistently provide the most conservative estimate of leaching, supporting the need to consider alternative methodologies in future regulatory development.

Implications: This paper analyzes the existing hazardous waste regulatory testing requirement for municipal solid waste incinerator (MSWI) ash management to evaluate whether the TCLP serves its intended purpose in providing the most conservative estimate of landfilled MSWI ash. The results will serve as guidance and motivation for policy makers and the regulatory community to reevaluate the TCLP’s application for characterizing MSWI ash leaching in certain disposal scenarios and could promote consideration of alternative testing procedures based upon results of this study. This study serves to promote representative and accurate quantification of leaching risk from MSWI ash.     

Comparisons of metal leachability for various wastes by extraction and leaching methods

The objective of this research was to evaluate three extraction tests, i.e., toxicity characteristic leaching procedures (TCLP), extraction procedure (EP), and American Society for Testing and Materials (ASTM) methods, for their ability to extract metals in chemical sludge and incineration bottom ash, in terms of the precision of analytical results. Typical chemical sludges, including the electroplating and dye-stuff sludges, the municipal solid waste incineration bottom ash, the leather debris, and the steel-mill bottom residue containing Cd, Cr, Cu, Pb, and Zn were prepared for the lysimetry test (dynamic testing) to compare with the extraction results. Results show that for bottom residue and dye-stuff sludge, the concentration of metal leached was almost the same between the lysimetry leaching and the TCLP tests. The metal concentration followed the order: TCLP approximately = EP > ASTM. TCLP and EP exhibited almost the same relative standard deviation (RSD) value. Therefore, the results of the TCLP tests for bottom residue and dye-stuff sludge, which have a low metal content and alkalinity, can be used to estimate the metal concentration leached by typical acid rain in Taiwan; whereas the ASTM extraction test may be a better indicator of the lysimetry test.     

Leaching Dynamics Studies of Municipal Solid Waste Incinerator Ash

Abstract

An assessment of the short- and long-term hazards from municipal solid waste incinerator (MSWI) ash is made through the elemental analysis of 40 to 50 elements in the ash and leachates produced by several leaching procedures. The ash was analyzed using neutron activation analysis (NAA) and x-ray fluorescence (XRF). The leachates were analyzed using NAA and inductively-coupled plasma atomic emission spectroscopy (ICP). The leaching dynamics of an ash monofill were modelled with a series of extractions using simulated acid rain. An initial spike of the metals Ag, Ba, Be, Cr, Cu, Mo, Pb, Sr, and Zn in the leachates appears to be the greatest hazard posed by MSWI ash monofills. The elements As, Cd, Cu, Hg, Pb, S, and Zn were identified as potential long term hazards utilizing a sequential extraction procedure which approximates the total amount of the elements available over the lifetime of the monofill.

The pH of the resulting leachate is the single greatest factor governing the concentration of metals in solution, more important than the concentration of the element in the ash. These results are applied to an assessment of the suitability of the Toxicity Characteristic Leaching Procedure (TCLP) in measuring leaching potential of an MSWI ash monofill.     

Heavy metals in urban soils of East St. Louis, IL. Part II: Leaching characteristics and modeling

The city of East St. Louis, IL, has a history of abundant industrial activities including smelters of ferrous and non-ferrous metals, a coal-fired power plant, companies that produced organic and inorganic chemicals, and petroleum refineries. Following a gross assessment of heavy metals in the community soils (see Part I of this two-part series), leaching tests were performed on specific soils to elucidate heavy metal-associated mineral fractions and general leachability. Leaching experiments, including the Toxicity Characteristic Leaching Procedure (TLCP) and column tests, and sequential extractions, illustrated the low leachability of metals in East St. Louis soils. The column leachate results were modeled using a formulation developed for fly ash leaching. The importance of instantaneous dissolution was evident from the model. By incorporating desorption/adsorption terms into the source term, the model was adapted very well to the time-dependent heavy metal leachate concentrations. The results demonstrate the utility of a simple model to describe heavy metal leaching from contaminated soils.     

Effects of soil amendments at a heavy loading rate associated with cover crops as green manures on the leaching of nutrients and heavy metals from a calcareous soil

The potential risk of groundwater contamination by the excessive leaching of N, P and heavy metals from soils amended at heavy loading rates of biosolids, coal ash, N-viro soil (1:1 mixture of coal ash and biosolids), yard waste compost and co-compost (3:7 mixture of biosolids to yard wastes), and by soil incorporation of green manures of sunn hemp (Crotalaria juncea) and sorghum sudangrass (Sorghum bicolor x S. bicolor var. sudanense) was studied by collecting and analyzing leachates from pots of Krome very gravelly loam soil subjected to these treatments. The control consisted of Krome soil without any amendment. The loading rate was 205 g pot(-1) for each amendment (equivalent to 50 t ha(-1) of the dry weight), and the amounts of the cover crops incorporated into the soil in the pot were those that had been grown in it. A subtropical vegetable crop, okra (Abelmoschus esculentus L.), was grown after the soil amendments or cover crops had been incorporated into the soil. The results showed that the concentration of NO3-N in leachate from biosolids was significantly higher than in leachate from other treatments. The levels of heavy metals found in the leachates from all amended soils were so low, as to suggest these amendments may be used without risk of leaching dangerous amounts of these toxic elements. Nevertheless the level of heavy metals in leachate from coal ash amended soil was substantially greater than in leachates from the other treatments. The leguminous cover crop, sunn hemp, returned into the soil, increased the leachate NO3-N and inorganic P concentration significantly compared with the non-legume, sorghum sudangrass. The results suggest that at heavy loading rates of soil amendments, leaching of NO3- could be a significant concern by application of biosolids. Leaching of inorganic P can be increased significantly by both co-compost and biosolids, but decreased by coal ash and N-viro soil by virtue of improved adsorption. The leguminous cover crop, sunn hemp, when incorporated into the soil, can cause the concentration of NO3-N to increase by about 7 fold, and that of inorganic P by about 23% over the non-legume. Regarding the metals, biosolids, N-viro soil and coal ash significantly increased Ca and Mg concentrations in leachates. Copper concentration in leachate was increased by application of biosolids, while Fe concentration in leachates was increased by biosolids, coal ash and co-compost. The concentrations of Zn, Mo and Co in leachate were increased by application of coal ash. The concentrations of heavy metals in leachates were very low and unlikely to be harmful, although they were increased significantly by coal ash application.     

Heavy Metals in Urban Soils of East St. Louis,IL Part II: Leaching Characteristics and Modeling

ABSTRACT

The city of East St. Louis, IL, has a history of abundant industrial activities including smelters of ferrous and non-ferrous metals, a coal-fired power plant, companies that produced organic and inorganic chemicals, and petroleum refineries. Following a gross assessment of heavy metals in the community soils (see Part I of this two-part series), leaching tests were performed on specific soils to elucidate heavy metal-associated mineral fractions and general leachability. Leaching experiments, including the Toxicity Characteristic Leaching Procedure (TLCP) and column tests, and sequential extractions, illustrated the low leachability of metals in East St. Louis soils. The column leachate results were modeled using a formulation developed for fly ash leaching. The importance of instantaneous dissolution was evident from the model. By incorporating desorption/adsorption terms into the source term, the model was adapted very well to the time-dependent heavy metal leachate concentrations. The results demonstrate the utility of a simple model to describe heavy metal leaching from contaminated soils.     

Leaching of the organophosphorus nematicide fosthiazate

Fosthiazate is an organophosphorus nematicide which was recently included in Annex I of the Directive 91/414/EEC under the clause that it should be used with special care in soils vulnerable to leaching. Thus, the leaching of fosthiazate was investigated in columns packed with three different soils which represented situations of high (site 2), intermediate (site 1) and low (site 3) leaching potential. The recommended dose of fosthiazate was applied at the surface of the soil columns and fosthiazate fate and transport was investigated for the next two months. Fosthiazate concentrations in the leachate collected from the bottom of the columns packed with soil from site 2 exceeded 0.1 microgl(-1) in most cases. This soil was characterized as acidic, indicating longer fosthiazate persistence, with low organic matter content, indicating weak adsorption, thus representing a situation vulnerable to leaching. In contrast, the lowest concentrations of fosthiazate in the leachate were evident in the columns packed with soil from site 3. This soil was characterized as alkaline, indicating faster degradation, with higher organic matter content, indicating stronger adsorption, thus representing a situation not favoring leaching of fosthiazate. The highest concentration of fosthiazate in the leachate from the columns packed with soil from site 2 was 3.44 microgl(-1) compared to 1.17 and 0.16 microgl(-1), which were the corresponding maximum values measured in columns packed with soil from sites 1 and 3, respectively. The results of the current study further suggest that fosthiazate is mobile in soil and can leach under conducive soil conditions like acidic soils with low organic matter content.     

Batch test assessment of waste-to-energy combustion residues impacts on precipitate formation in landfill leachate collection systems

Disposal practices for bottom ash and fly ash from waste-to-energy (WTE) facilities include emplacement in ash monofills or co-disposal with municipal solid waste (MSW) and residues from water and wastewater treatment facilities. In some cases, WTE residues are used as daily cover in landfills that receive MSW. A recurring problem in many landfills is the development of calcium-based precipitates in leachate collection systems. Although MSW contains varying levels of calcium, WTE residues and treatment plant sludges have the potential to contribute concentrated sources of leachable minerals into landfill leachates. This study was conducted to evaluate the leachability of calcium and other minerals from residues generated by WTE combustion using residues obtained from three WTE facilities in Florida (two mass-burn and one refuse-derived fuel). Leaching potential was quantified as a function of contact time and liquid-to-solid ratios with batch tests and longer-term leaching tests using laboratory lysimeters to simulate an ash monofill containing fly ash and bottom ash. The leachate generated as a result of these tests had total dissolved solid (TDS) levels ranging from 5 to 320 mg TDS/g ash. Calcium was a major contributor to the TDS values, contributing from 20 to 105 g calcium/kg ash. Fly ash was a major contributor of leachable calcium. Precipitate formation in leachates from WTE combustion residues could be induced by adding mineral acids or through gas dissolution (carbon dioxide or air). Stabilization of residual calcium in fly ashes that are landfilled and/or the use of less leachable neutralization reagents during processing of acidic gases from WTE facilities could help to decrease the calcium levels in leachates and help to prevent precipitate formation in leachate collection systems.     

Reduced downward mobility of metribuzin in fly ash-amended soils

Metribuzin, a triazine herbicide, is poorly sorbed in the soils, therefore leaches to lower soil profile. Fly ash amendment, which enhanced metribuzin sorption in soils, may play a significant role in reducing the downward mobility of herbicide. Therefore, the present study reports the effect of Inderprastha fly ash amendment on metribuzin leaching in three soil types. Fly ash was amended at 1, 2 and 5% levels in the upper 15 cm of 30 cm long packed soil columns. Results suggested a significant reduction in the leaching losses of metribuzin in fly ash-amended columns of all the three soil types and effect increased with increase in the level of fly ash. Even after percolating water equivalent to 362 mm rainfall no metribuzin was recovered in the leachate of 5% fly ash-amended columns. Fly ash application affected both metribuzin breakthrough time and its maximum concentration in the leachate. Further, it resulted in greater retention of metribuzin in the application zone and better effect was observed in the organic carbon poor soils.     

Study of the use of coal fly ash as an additive to minimise fluoride leaching from FGD gypsum for its disposal

The use of coal fly ash as a fluoride retention additive has been studied as a way of treating flue gas desulphurisation (FGD) gypsum for its disposal in landfills. With this end leaching studies following the standard EN-12457-4 [Characterization of waste- Leaching-Compliance test for leaching of granular waste materials and sludges - Part 4: One stage batch test at a liquid to solid ratio of 10l/kg for materials with particle size below 10mm (without or with size reduction)] have been performed on FGD gypsum samples treated with different proportions of fly ash (0.1-100%). It was found that the fluoride leachable content in FGD gypsum was reduced in the range 1-55%, depending on the fly ash proportion added to FGD gypsum. High levels of fluoride leaching reduction (close to 40%) were achieved even at relatively low fly ash additions (5%). So, low fly ash incorporations assure the characterization of this by-product as a waste acceptable at landfills for non-hazardous wastes according to the Council Decision 2003/33/EC [Council Decision 2003/33/EC of 19 December 2002 establishing criteria and procedures for the acceptance of waste at landfills pursuant to Article 16 of and Annex II to Directive 1999/31/EC] on waste disposal. Furthermore, the effectiveness of the proposed FGD gypsum stabilization method was also studied in column leaching systems, proving its good performance in simulated conditions of disposal. In such conditions a fluoride leaching reduction value slightly higher than 25% was displayed for a fly ash added amount of 5%.     

Fractionation and mobility of metals in bauxite red mud

Red mud (RM) is a strongly alkaline residue generated in enormous amounts worldwide from bauxite refining using the Bayer chemical process. RM is composed mainly of Fe, Ti and Al oxides and hydroxides, but it also contains an array of trace metals and metalloids at different concentrations. The purpose of this paper is to assess the potential mobility of metals in RM, with special emphasis on pH effect. The ‘operational’ distribution and leachability of metals within/from RM was studied by applying a sequential extraction procedure (SEP) and several leaching tests (rapid titration, equilibration acidification, batch leaching with acetic acid and also the toxicity characteristics leaching procedure (TCLP) and the DIN 38414-S4 procedures, used as reference methods) carried out at different pH, solid/liquid ratio, extraction period and type of acid (HCl or acetic acid). Chemical analysis showed that, in addition to the major metals Fe, Al and Ti, RM contains several trace metals, some of them (Cr, Cu and Ni) in concentrations exceeding the regulatory limits. SEP showed that a majority of the metals in the RM (between the 32.2?±?8.5 for Cd and 95.3?±?0.4 % for Ni) were found in the residual fraction, suggesting that they are not readily mobile under normal environmental conditions. Leaching tests performed at different pH showed that a significant fraction of the metals is mobilised from RM only under very strong acid conditions (pH?<?2), whereas Al is released in considerable amounts at pH?<?5.3. Among the trace metals, Cr requires special attention because of its relative high concentration in RM and the higher concentrations of this metal mobilised at low pH. The leaching tests using acetic acid showed that the standard TCLP largely underestimates the release of trace metals from RM, and therefore it is not advisable to evaluate the actual potential leaching of trace metals from this residue.     

Effects of Soil Amendments at a Heavy Loading Rate Associated with Cover Crops as Green Manures on the Leaching of Nutrients and Heavy Metals from a Calcareous Soil

The potential risk of groundwater contamination by the excessive leaching of N, P and heavy metals from soils amended at heavy loading rates of biosolids, coal ash, N‐viro soil (1:1 mixture of coal ash and biosolids), yard waste compost and co‐compost (3:7 mixture of biosolids to yard wastes), and by soil incorporation of green manures of sunn hemp (Crotalaria juncea) and sorghum sudangrass (Sorghum bicolor × S. bicolor var. sudanense) was studied by collecting and analyzing leachates from pots of Krome very gravelly loam soil subjected to these treatments. The control consisted of Krome soil without any amendment. The loading rate was 205 g pot^? 1 for each amendment (equivalent to 50 t ha^? 1 of the dry weight), and the amounts of the cover crops incorporated into the soil in the pot were those that had been grown in it. A subtropical vegetable crop, okra (Abelmoschus esculentus L.), was grown after the soil amendments or cover crops had been incorporated into the soil. The results showed that the concentration of NO₃‐N in leachate from biosolids was significantly higher than in leachate from other treatments. The levels of heavy metals found in the leachates from all amended soils were so low, as to suggest these amendments may be used without risk of leaching dangerous amounts of these toxic elements. Nevertheless the level of heavy metals in leachate from coal ash amended soil was substantially greater than in leachates from the other treatments. The leguminous cover crop, sunn hemp, returned into the soil, increased the leachate NO₃‐N and inorganic P concentration significantly compared with the non‐legume, sorghum sudangrass. The results suggest that at heavy loading rates of soil amendments, leaching of NO₃ ^? could be a significant concern by application of biosolids. Leaching of inorganic P can be increased significantly by both co‐compost and biosolids, but decreased by coal ash and N‐viro soil by virtue of improved adsorption. The leguminous cover crop, sunn hemp, when incorporated into the soil, can cause the concentration of NO₃‐N to increase by about 7 fold, and that of inorganic P by about 23% over the non‐legume. Regarding the metals, biosolids, N‐viro soil and coal ash significantly increased Ca and Mg concentrations in leachates. Copper concentration in leachate was increased by application of biosolids, while Fe concentration in leachates was increased by biosolids, coal ash and co‐compost. The concentrations of Zn, Mo and Co in leachate were increased by application of coal ash. The concentrations of heavy metals in leachates were very low and unlikely to be harmful, although they were increased significantly by coal ash application.     

Dynamic studies on the mobility of trace elements in soil and sediment samples influenced by dumping of residues of the flood in the Mulde River region in 2002

In the analysis of soil samples, batch sequential extraction procedures are traditionally used for the fractionation of trace elements to access their mobility and potential risk for the contamination of groundwater. In the present work a continuous-flow technique has been used that enables not only the fast and efficient leaching of trace elements but as well as time-resolved studies on the mobilization of arsenic and selected heavy metals in different forms to be made. Rotating coiled columns (RCC) earlier used mainly in countercurrent chromatography have been successfully applied to the dynamic leaching of heavy metals from soils contaminated by flooding sludge's. The sample was retained in a PTFE rotating column as the stationary phase whereas aqueous solutions were continuously pumped through. The contents of elements were determined by on-line coupling of RCC and inductively coupled plasma atomic emission spectrometry (ICP-AES). This enables real-time data on the leaching process to be obtained. Dynamic and traditional batch procedures were compared. It has been shown that the aqueous elution under centrifugal forced conditions is much more effective for the mobilization of heavy metals. Hence, the dynamic leaching is characterized by a substantially more intensive interaction between solid and water and is besides substantially more time-saving than the conventional batch procedure. The RCC procedure was also employed for preliminary leaching studies with a simulated "acid rain". In comparison with the water leaching, the mobilization of heavy metals and arsenic from soil samples with employment of simulated acid rain as eluent was less effective.     

Element immobilization in refuse incinerator ashes by solidification in glass, ceramic or cement

Incineration of municipal refuse results in the production of massive quantities of fly ash and bottom ash. Toxic elements in the original refuse may be concentrated up to 40-fold in the resultant ash. There is concern that burial of such ash in landfills could result in leaching of these elements downward into groundwater. In this study, refuse ashes were incorporated into glass, ceramic and cement composites to immobilize such toxic elements. The EP Toxicity Test (1986) was used to show that extraction of such elements by simulated acid rain is effectively blocked in these new solid materials.     

Leaching characteristics of PCDDs/DFs and dioxin-like PCBs from landfills containing municipal solid waste and incineration residues

To investigate the leaching characteristic of persistent organic pollutants (POPs), such as non-ortho and mono-ortho substituted chlorobiphebyls (dioxin-like PCBs), polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDDs/DFs), in leachate from municipal solid waste (MSW) landfill sites containing incineration residues, raw leachate samples were collected twice from 12 selected MSW landfill sites. The samples were divided into their liquid and solid phases using GF/B (pore size 1.0 microm), and the concentrations of POPs then determined. The concentrations of PCDDs/DFs ranged from 0.65 to 5.88 pg-TEQ/l (average 2.86 pg-TEQ/l), and those of dioxin-like PCBs from 0.05 to 0.32 pg-TEQ/l (average 0.18 pg-TEQ/l). The major congeners of leached PCDDs/DFs and dioxin-like PCBs in liquid and solid phases were OCDD (about 60%), 2,3',4,4',5-PeCBs (about 30%), and 2,3,4,4',5-PeCBs (about 54%). The relationship between landfill age and the leaching concentration of PCDDs/DFs, and effects of dissolved organic carbon (DOC) on the leaching of PCDDs/DFs are also discussed. Finally, a leaching prediction model of PCDDs/DFs from MSW landfills has been suggested using parameters, such as hydrophobic neutral organic carbons, total dissolved solid, and the ratio of non-biodegradable wastes in landfill sites.     

PCDD/DF in leachates from Korean MSW landfills

We analyzed levels of PCDD/DF in leachate liquid and solid from five Korean municipal solid waste landfills to investigate the relationship between PCDD/DF and dissolved organic carbon and suspended solids in raw leachate. The concentrations of PCDD/DF ranged from 173.2 to 1329.4 pg/l and 4.1 to 46.22 pg-TEQ/l. The range of PCDD/DF was 123.2-1161.3 pg/l in leachate solid and 50.0-383.3 pg/l in leachate liquid. Our results indicated that PCDD/DF in solid play a major role in determining their concentration levels, and the distribution of isomers in solid was almost the same as in liquid leachate. In addition, highly chlorinated PCDD/DF, such as HpCDD/DF and OCDD/DF, accounted for more than 70% of all isomers. Levels of PCDD/DF in liquid were strongly correlated with dissolved organic carbon concentrations, which increase the leachability (R2 = 0.92 in Korean leachate) of PCDD/DF from contaminant sources. Despite this high linearity between dissolved organic carbon and dissolved PCDD/DF, we observed no strong relationship between dissolved organic carbon and solid phase PCDD/DF (R2 = 0.001). Dissolved organic carbon scarcely affects dissolved PCDD/DF to be combined with solids. As a result, it is not appropriate for incinerated ash to be dumped with municipal solid wastes, as they have a large potential to result in high levels of organic matter, and therefore PCDD/DF, in leachate.     

Metals leachability from medical waste incinerator fly ash: A case study on particle size comparison

This paper presents the results from a study of metals leachability of medical waste incinerator fly ash in Japan on the basis of particle size. Sequential extraction and Toxicity Characteristic Leaching Procedure (TCLP) analysis were carried out in order to quantify the leaching amount of metals in each categorized particle size. Sequential extraction was also subjected to identify the preference of binding matrix of metals. The results of sequential extraction showed an increase both exchangeable and carbonate associated chromium concentrations in the bigger particle size fractions. Likewise, concentrations of carbonate matrix of arsenic and tin tended to increase in the bigger particle size fractions. In contrast, exchangeable associated cadmium as well as both exchangeable and carbonate matrices of barium were found higher in the smaller particle size fractions. However, no correlation was found in Kendal-tau correlation analysis between particle size of the ash and metals leachability of the TCLP.     

间歇式生物反应器填埋结构对渗滤液水质的影响研究

通过2套间歇式生物反应器填埋模拟装置开展实验,对不同填埋结构下垃圾降解前期渗滤液pH值、COD、NH 4＋-N、VFA以及渗滤液产生量的变化规律进行了对比研究。实验结果表明：间歇式生物反应器填埋方式能够有效抑制填埋初期渗滤液pH值的快速下降,渗滤液采取部分回灌能有效降低NH4＋-N浓度的积累,新鲜垃圾与半腐熟垃圾分层并...     

Cell cycle stage specific application of municipal landfill leachates to assess the genotoxicity in root meristem cells of barley (Hordeum vulgare)

Municipal solid wastes (MSW) are unavoidable sources of environmental pollution. Improper disposal of municipal waste results in the leaching of toxic metals and organic chemicals, which can contaminate the surface and ground water leading to serious health hazard. In this study, the toxic effects of the leachate prepared from municipal solid waste samples were examined in root meristem cells of barley (Hordeum vulgare L.) at various stages of cell cycle, i.e., G₁, S, and G₂. Seeds of barley were exposed to 2.5, 5, and 10 % of leachates in soil and aqueous media in 48 h at different cell cycle stages. The physicochemical data of the present study revealed that municipal solid waste leachate contains high amount of heavy metals, which significantly affected growth and physiological activities of barley. Significant inhibition in hypocotyl length, germination, and mitotic index were observed at all concentration of leachate treatment. Induction of chromosomal aberrations (CA’s) and micronuclei (MN) formation were also observed with different concentrations of leachate treatment at 7, 17, and 27 h of presoaking durations, which falls in G₁, S, and G₂ phase of the cell cycle, respectively. Also, exposure of leachate at S phase of the cell cycle had significant effects in barley through chromosomal aberration and micronuclei formation.