A passive flux denuder for evaluating emissions of ammonia at a dairy farm

Passive samplers have been shown to be an inexpensive alternative to direct sampling. Diffusion denuders have been developed to measure the concentration of species such as ammonia (NH3), which is in equilibrium with particulate ammonium nitrate. Conventional denuder sampling has required active sampling that inherently requires air pumps and, therefore, electrical power. To estimate emissions of NH3 from a fugitive source would require an array of active samplers and meteorological measurements to estimate the flux. A recently developed fabric denuder was configured in an open tube to passively sample NH3 flux. Passive and active samplers were collocated at a dairy farm at the California State University, Fresno, Agricultural Research Facility. During this comparison study, NH3 flux measurements were made at the dairy farm lagoon before and after the lagoon underwent acidification. Comparisons were made of the flux measurements obtained directly from the passive flux denuder and those calculated from an active filter pack sampler and wind velocity. The results show significant correlation between the two methods, although a correction factor needed to be applied to directly compare the two techniques. This passive sampling approach significantly reduces the cost and complexity of sampling and has the potential to economically develop a larger inventory base for ambient NH3 emissions.     

Ammonia emissions from naturally ventilated dairy cattle buildings and outdoor concrete yards in Portugal

There is a lack of information on ammonia (NH₃) emissions from cattle housing systems in Mediterranean countries, with most published data deriving from NW Europe. An investigation was carried out in NW Portugal to quantify NH₃ emissions for the main types of dairy cattle buildings in Portugal, i.e. naturally ventilated buildings and outdoor concrete yards, and to derive robust emission factors (EFs) for these conditions and compare with EFs used elsewhere in Europe. Measurements were made throughout a 12-month period using the passive flux sampling method in the livestock buildings and the equilibrium concentration technique in outdoor yards.The mean NH₃ emission factor for the whole housing system (buildings + outdoor yards) was 43.7 g NH₃–N LU^?1 day^?1 and for outdoor concrete yards used by dairy cattle was 26.6 g NH₃–N LU^?1 day^?1. Expressing NH₃ emission in terms of the quantity of liquid milk produced gave similar values across the three dairy farms studied (with a mean of 2.3 kg N ton-milk^?1 produced) and may have advantages when comparing different farming systems. In dairy houses with outdoor yards, NH₃ emissions from the yard area contributed to 69–92% of total emissions from this housing system. Emissions were particularly important during spring and summer seasons from outdoor yards with NH₃ emitted in this period accounting for about 72% of annual emissions from outdoor yards. Mean NH₃ emission factors derived for this freestall housing system and outdoor concrete yards used by dairy cattle in Portugal were higher than those measured in northern Europe. In addition, values of animal N excretion estimated in this study were greater than official National standard values. If these emissions are typical for Portuguese dairy systems, then the current National inventory underestimates emissions from this source in NW of Portugal, because of the use of lower standard values of N excretion by dairy cattle.     

Seasonal and Spatial Variations of Ammonia Emissions from an Open-Lot Dairy Operation

Abstract

There is a need for a robust and accurate technique to measure ammonia (NH₃) emissions from animal feeding operations (AFOs) to obtain emission inventories and to develop abatement strategies. Two consecutive seasonal studies were conducted to measure NH₃ emissions from an open-lot dairy in central Texas in July and December of 2005. Data including NH₃ concentrations were collected and NH₃ emission fluxes (EFls), emission rates (ERs), and emission factors (EFs) were calculated for the open-lot dairy. A protocol using flux chambers (FCs) was used to determine these NH₃ emissions from the open-lot dairy. NH₃ concentration measurements were made using chemiluminescence-based analyzers. The ground-level area sources (GLAS) including open lots (cows on earthen corrals), separated solids, primary and secondary lagoons, and milking parlors were sampled to estimate NH₃ emissions. The seasonal NH₃ EFs were 11.6 ± 7.1 kg-NH₃ yr^-1head^-1 for the summer and 6.2 ± 3.7 kg-NH₃ yr^-1head^-1 for the winter season. The estimated annual NH₃ EF was 9.4 ± 5.7 kg-NH₃ yr^-1head^-1 for this open-lot dairy. The estimated NH₃ EF for winter was nearly 47% lower than summer EF. Primary and secondary lagoons (～37) and open-lot corrals (～63%) in summer, and open-lot corrals (～95%) in winter were the highest contributors to NH₃ emissions for the open-lot dairy. These EF estimates using the FC protocol and real-time analyzer were lower than many previously reported EFs estimated based on nitrogen mass balance and nitrogen content in manure. The difference between the overall emissions from each season was due to ambient temperature variations and loading rates of manure on GLAS. There was spatial variation of NH₃ emission from the open-lot earthen corrals due to variable animal density within feeding and shaded and dry divisions of the open lot. This spatial variability was attributed to dispirit manure loading within these areas.     

Measuring ammonia emissions from land applied manure: an intercomparison of commonly used samplers and techniques

A number of techniques have been developed to quantify ammonia (NH(3)) emissions following land application of manure or fertiliser. In this study, coefficients of variation were determined for three commonly used field techniques (mass balance integrated horizontal flux, wind tunnels and the equilibrium concentration technique) for measuring emissions from a range of manure types. Coefficients of variation (CV) for absorption flasks, passive flux samplers and passive diffusion samplers were 21, 10 and 14%, respectively. In comparative measurements, concentrations measured using passive flux samplers and absorption flasks did not differ significantly, but those measured using passive diffusion samplers were on average 1.8 times greater. The mass balance technique and wind tunnels gave broadly similar results in two out of four field tests. Overexposure of passive diffusion samplers for some sampling periods meant that estimation of cumulative NH(3) emission using the equilibrium concentration technique in the field tests could not be made. For cumulative NH(3) emissions, CVs were in the range of 23-52, 46-74 and 21-39% for the mass balance, wind tunnel and equilibrium concentration techniques, respectively. Lower CVs were associated with measurements following slurry compared with solid manure applications. Our conclusions from this study are that for the measurement of absolute emissions the mass balance technique is to be preferred, and for small-plot comparative measurements the wind tunnel system is preferred to the equilibrium concentration technique.     

An estimate of the contribution of outdoor concrete yards used by livestock to the UK inventories of ammonia, nitrous oxide and methane

Many farms have unroofed concrete yards used by livestock. These concrete yards have received little attention as sources of gaseous emissions. From 1997 to 1999 measurements were made of emissions of ammonia (NH₃), nitrous oxide (N₂O) and methane (CH₄) from 11 concrete yards used by livestock. A postal survey was carried out to assess the areas of yards on farms in England and Wales to enable the measurements to be scaled up to estimate national emissions. Using the results of this study NH₃-N emissions from farm concrete yards were calculated to be ca. 35×10³ t annually. This is 13% of the current estimated total NH₃-N emission from UK livestock. Concrete yards were an insignificant source of N₂O and CH₄ which were both <0.01% of current estimates of agricultural emissions.     

Use of Two Different Acidic Aerosol Samplers To Measure Acidic Aerosols in Hsinchu,Taiwan

ABSTRACT

Acidic aerosol concentrations measured by an annular denuder system (ADS) and a honeycomb denuder system (HDS) in Hsinchu, Taiwan, were compared. Aerosols were also sampled by a MOUDI (micro-orifice uniform deposit impactor) and analyzed by an ion chromatograph to determine the size distributions of different species. Using the measured aerosol size distribution, theoretical analysis showed that positive HNO₃ artifact due to volatiliza-tion of NH₄NO₃ is generally negligible for both samplers.4 3Comparing two different denuder samplers, the average concentration of HNO₃ measured by the ADS was found3to be lower than that measured by the HDS, while the difference between the two samplers for the average concentration of other species was found to be within ±15%. A possible cause of the difference in HNO₃ con-3centrations is due to a greater loss of HNO₃ in the cyclone3 used by the ADS than in the impactor used by the HDS. The study also showed incomplete absorption of the evaporated HCl and HNO₃ from the particles on the Teflon3filter by the first nylon filter in the filter pack of the ADS. Collection efficiency and capacity of HCl and HNO₃ by3the nylon filters need further investigation.     

Precision and Accuracy in the Determination of Sulfur Oxides,Fluoride, and Spherical Aluminosilicate Fly Ash Particles in Project MOHAVE

The precision and accuracy of the determination of particu-late sulfate and fluoride, and gas phase SO₂ and HF are estimated from the results obtained from collocated replicate samples and from collocated comparison samples for high-and low-volume filter pack and annular diffusion denuder samplers. The results of replicate analysis of collocated samples and replicate analyses of a given sample for the determination of spherical aluminosilicate fly ash particles have also been compared. Each of these species is being used in the chemical mass balance source apportionment of sulfur oxides in the Grand Canyon region as part of Project MOHAVE, and the precision and accuracy analyses given in this paper provide input to that analysis. The precision of the various measurements reported here is ±1.8 nmol/m³ and ±2.5 nmol/m³ for the determination of SO₂ and sulfate, respectively, with an annular denuder. The precision is ±0.5 nmol/m³ and ±2.0 nmol/m³ for the determination of the same species with a high-volume or low-volume filter pack. The precision for the determination of the sum of HF(g) and fine particulate fluoride is ±0.3 nmol/m³. The precision for the determination of aluminosilicate fly ash particles is ±100 particles/m³. At high concentrations of the various species, reproducibility of the various measurements is ±10% to ±14% of the measured concentration. The concentrations of sulfate determined using filter pack samplers are frequently higher than those determined using diffusion denuder sampling systems. The magnitude of the difference (e.g., 2-10 nmol sulfate/m³) is small, but important relative to the precision of the data and the concentrations of particulate sul-fate present (typically 5-20 nmol sulfate/m³). The concentrations of SO₂(g) determined using a high-volume cascade impactor filter pack sampler are correspondingly lower than those obtained with diffusion denuder samplers. The concentrations of SO_x (SO₂(g) plus particulate sulfate) determined using the two samplers during Project MOHAVE at the Spirit Mountain, NV, and Hopi Point, AZ, sampling sites were in agreement. However, for samples collected at Painted Desert, AZ, and Meadview, AZ, the concentrations of SO_x and SO₂(g) determined with a high-volume cascade impactor filter pack sampler were frequently lower than those determined using a diffusion denuder sampling system. These two sites had very low ambient relative humidity, an average of 25%. Possible causes of observed differences in the SO₂(g) and sulfate results obtained from different types of samplers are given.     

Abatement of Ammonia and Hydrogen Sulfide Emissions from a Swine Lagoon Using a Polymer Biocover

ABSTRACT

The purpose of this research was to determine the efficiency of a polymer biocover for the abatement of H₂S and NH₃ emissions from an east-central Missouri swine lagoon with a total surface area of 7800 m². The flux rate of NH₃, H₂S, and CH₄ was monitored continuously from two adjacent, circular (d = 66 m) control and treatment plots using a nonintrusive, micrometeorological method during three independent sampling periods that ranged between 52 and 149 hr. Abatement rates were observed to undergo a temporal acclimation event in which NH₃ abatement efficiency improved from 17 to 54% (p = <0.0001 to 0.0005) and H₂S abatement efficiency improved from 23 to 58% (p < 0.0001) over a 3-month period. The increase in abatement efficiency for NH₃ and H₂S over the sampling period was correlated with the development of a stable anaerobic floc layer on the bottom surface of the biocover that reduced mass transfer of NH₃ and H₂S across the surface. Analysis of methanogenesis activity showed that the biocover enhanced the rate of anaerobic digestion by 25% when compared with the control. The biocover-enhanced anaerobic digestion process was shown to represent an effective mechanism to counteract the accumulation of methanogenic substrates in the biocovered lagoon.     

Ammonia Flux from Open-Lot Dairies: Development of Measurement Methodology and Emission Factors

Abstract

Ammonia emissions contribute to the formation of secondary particulate matter (PM) and violations of the National Ambient Air Quality Standard. Ammonia mass concentration measurements were made in February 1999 upwind and downwind of an open-lot dairy in California, using a combination of active bubbler and passive filter samplers. Ammonia fluxes were calculated from concentrations measured at 2, 4, and 10 m above ground at three locations on the downwind edge of the dairy, using micrometeorological techniques. A new method was developed to interpolate fluxes at six additional locations from ammonia concentrations measured at a single height, providing measurements at sufficient spatial resolution along the downwind border of the dairy to account for the heterogeneity of the source. PM measured up- and downwind of the dairy demonstrated insignificant ammonium particle formation in the immediate vicinity of the dairy and negligible contribution of dissociated ammonium nitrate to measured ammonia concentrations. Ammonium nitrate concentrations measured downwind of the dairy ranged from 26 to 0.26 μg m^?3 and from 2 to 43% of total PM_2.5 mass concentrations. Measured ammonia fluxes showed that liquid manure retention ponds represented relatively minor sources of ammonia in winter on the dairy studied. Ammonia emission factors derived from the measurements ranged from 19 to 143 g head^?1 day^?1, showing an increase with warmer, drier weather and a decrease with increased relative humidity and lower temperatures.     

Field Method Comparison between Passive Air Samplers and Continuous Monitors for VOCs and NO2 in El Paso,Texas

Abstract

This study evaluates the performance of Model 3300 Ogawa Passive Nitrogen Dioxide (NO₂) Samplers and 3M 3520 Organic Vapor Monitors (OVMs) by comparing integrated passive sampling concentrations to averaged hourly NO₂ and volatile organic compound (VOC) measurements at two sites in El Paso, TX. Sampling periods were three time intervals (3-day weekend, 4-day weekday, and 7-day weekly) for three consecutive weeks. OVM concentrations were corrected for ambient pressure to account for higher elevation. Precise results (<5% relative standard deviation, RSD) were found for NO₂ measurements from collocated Ogawa samplers. Reproducibility was lower from duplicate OVMs for BTEX (benzene, toluene, ethylbenzene, and xylene isomers) VOCs (≥7% RSD for 2-day samples) with better precision for longer sampling periods. Comparison of Ogawa NO₂ samplers with chemiluminescence measurements averaged over the same time period suggested potential calibration problems with the chemiluminescence analyzer. For BTEX species, generally good agreement was obtained between OVMs and automated-gas chromatograph (auto-GC) measurements. The OVMs successfully tracked increasing levels of VOCs recorded by the auto-GCs.     

Intercalibration of a passive wind-vane flux sampler against a continuous-flow denuder for the measurements of atmospheric ammonia concentrations and surface exchange fluxes

A passive wind-vane flux sampler is a simple low-cost device used to estimate long-term vertical fluxes of ammonia in the atmospheric surface boundary layer. The passive flux sampler measures the horizontal flux of ammonia. A vertical gradient of the horizontal flux, combined with micro-meteorological measurements of wind speed and temperature, is used to estimated the vertical flux of ammonia using a modified aerodynamic gradient technique. The passive wind-vane flux sampler gradient was calibrated against a gradient measured with fast response (6 min) continuous-flow denuders. The measurements were carried out at a heathland located in an intensive farming area in the centre of the Netherlands. A field campaign took place over 70 day period in the summer of 1996, during which the sampling periods of the passive wind-vane flux sampler varied between 3 and 9 days. The comparison clearly showed that the long-term measurements with the passive wind-vane flux samplers gave accurate average ammonia deposition values for the field campaign as a whole which deviated by only 18% from the reference flux. However, there was no significant correlation between the fluxes from the passive samplers and the reference method for the individual 10 periods which were compared. Possible explanations found for the lacking correlation were (I) a high percentage number of half-hour emission events within each period resulted in a significant large relative deviation between the fluxes, and (II) uncertainties in the reference method might also explain the lacking correlation. The passive wind-vane flux samplers proved to be a stable method for long-term measurements (months to years) due to a close to 100% optimal functioning during the field campaign.     

Measurements of nitrogen dioxide on Funen using diffusion tubes

Monitoring of nitrogen dioxide (NO₂) by passive sampling on the Danish island Funen (Fyn) show that the concentration of nitrogen dioxide is low (2–20 ppb). The level of NO₂ in rural and suburban areas is governed by imported airpollution, and elevated NO₂ concentrations due to local traffic are of limited importance. These results are supported by diffusion denuder measurements of nitric acid (HNO₃) and particulate nitrate. Measurements of NO₂ with chemiluminescence and diffusive passive sampling showed good agreement between the methods. The special mounting device for the diffusive samplers used in this work seem to have reduced the turbulence at the open end of the tube. The product from the reaction between nitrogen dioxide and triethanolamine was investigated and tentatively identified as triethanolamine N-oxide, which is in accordance with the observed 1 : 1 stoechiometry in the conversion of NO₂ to nitrite ions.     

Validation of model calculation of ammonia deposition in the neighbourhood of a poultry farm using measured NH3 concentrations and N deposition

Substantial emission of ammonia (NH₃) from animal houses and the related high local deposition of NH₃-N are a threat to semi-natural nitrogen-deficient ecosystems situated near the NH₃ source. In Denmark, there are regulations limiting the level of NH₃ emission from livestock houses near N-deficient ecosystems that are likely to change due to nitrogen (N) enrichment caused by NH₃ deposition. The models used for assessing NH₃ emission from livestock production, therefore, need to be precise, as the regulation will affect both the nature of the ecosystem and the economy of the farmer. Therefore a study was carried out with the objective of validating the Danish model used to monitor NH₃ transport, dispersion and deposition from and in the neighbourhood of a chicken farm. In the study we measured NH₃ emission with standard flux measuring methods, NH₃ concentrations at increasing distances from the chicken houses using passive diffusion samplers and deposition using ¹⁵N-enriched biomonitors and field plot studies. The dispersion and deposition of NH₃ were modelled using the Danish OML-DEP model. It was also shown that model calculations clearly reflect the measured NH₃ concentration and N deposition. Deposition of N measured by biomonitors clearly reflected the variation in NH₃ concentrations and showed that deposition was not significantly different from zero (P < 0.05) at distances greater than 150–200 m from these chicken houses. Calculations confirmed this, as calculated N deposition 320 m away from the chicken farm was only marginally affected by the NH₃ emission from the farm. There was agreement between calculated and measured deposition showing that the model gives true estimates of the deposition in the neighbourhood of a livestock house emitting NH₃.     

A Fabric Denuder for Sampling Semi-Volatile Species

ABSTRACT

A new style of diffusion denuder has been evaluated specifically for sampling HNO₃. A coated fabric is used as the denuder substrate, which can be loaded directly into a standard filter holder. This approach allows direct denuder sampling with no additional capital costs over filter sampling and simplifies the coating and extraction process.

Potential denuder materials and coatings were evaluated in the laboratory to test the removal efficiency. NaCl coatings were used to assess more than 20 materials for HNO₃ collection efficiency. Particle retention, which would cause a denuder to have a positive bias for gas concentration measurements, was evaluated by ambient air sampling using particulate sulfate as the reference aerosol. Particle retention varied from 0 to 15%, depending on the denuder material tested. The best performing material showed an average particle retention of less than 3%.

Denuder efficiency of four fabric materials was tested under ambient conditions to determine removal efficiency. The fabric denuder method was compared with a long path-length Fourier transform infrared (FTIR) spectrometer, a tunable diode laser absorption spectrometer (TDLAS), and a denuder difference sampler to independently measure HNO₃. HNO₃ collection efficiency was typically 90% for the denuders, whether coated with NaCl or not. For 10-L/min sampling rates with the fabric denuder, the square of the correlation coefficient with the FTIR spectrometer was 0.73, compared to 0.24 with the TDLAS.     

Measurement and analysis of atmospheric ammonia emissions from anaerobic lagoons

Ammonia-nitrogen flux (NH₃-N=(14/17)NH₃) was determined from six anaerobic swine waste storage and treatment lagoons (primary, secondary, and tertiary) using the dynamic chamber system. Measurements occurred during the fall of 1998 through the early spring of 1999, and each lagoon was examined for approximately one week. Analysis of flux variation was made with respect to lagoon surface water temperature (∼15 cm below the surface), lagoon water pH, total aqueous phase NH_x(=NH₃+NH₄⁺) concentration, and total Kjeldahl nitrogen (TKN). Average lagoon temperatures (across all six lagoons) ranged from approximately 10.3 to 23.3^°C. The pH ranged in value from 6.8 to 8.1. Aqueous NH_x concentration ranged from 37 to 909 mg N l⁻¹, and TKN varied from 87 to 950 mg N l⁻¹. Fluxes were the largest at the primary lagoon in Kenansville, NC (March 1999) with an average value of 120.3 μg N m⁻² min⁻¹, and smallest at the tertiary lagoon in Rocky Mount, NC (November 1998) at 40.7 μg N m⁻² min⁻¹. Emission rates were found to be correlated with both surface lagoon water temperature and aqueous NH_x concentration. The NH₃-N flux may be modeled as ln(NH₃-N flux)=1.0788+0.0406T_L+0.0015([NH_x]) (R²=0.74), where NH₃-N flux is the ammonia flux from the lagoon surface in μg N m⁻² min⁻¹, T_L is the lagoon surface water temperature in ^°C, and [NH_x] is the total ammonia-nitrogen concentration in mg N l⁻¹.     

Characterization of the olfactory impact around a wastewater treatment plant: Optimization and validation of a hydrogen sulfide determination procedure based on passive diffusion sampling

A monitoring program based on an indirect method was conducted to assess the approximation of the olfactory impact in several wastewater treatment plants (in the present work, only one is shown). The method uses H₂S passive sampling using Palmes-type diffusion tubes impregnated with silver nitrate and fluorometric analysis employing fluorescein mercuric acetate. The analytical procedure was validated in the exposure chamber. Exposure periods of at least 4 days are recommended. The quantification limit of the procedure is 0.61 ppb for a 5-day sampling, which allows the H₂S immission (ground concentration) level to be measured within its low odor threshold, from 0.5 to 300 ppb. Experimental results suggest an exposure time greater than 4 days, while recovery efficiency of the procedure, 93.0 ± 1.8%, seems not to depend on the amount of H₂S collected by the samplers within their application range. The repeatability, expressed as relative standard deviation, is lower than 7%, which is within the limits normally accepted for this type of sampler. Statistical comparison showed that this procedure and the reference method provide analogous accuracy. The proposed procedure was applied in two experimental campaigns, one intensive and the other extensive, and concentrations within the H₂S low odor threshold were quantified at each sampling point. From these results, it can be concluded that the procedure shows good potential for monitoring the olfactory impact around facilities where H₂S emissions are dominant.

Implications: Passive samplers are very attractive tools to experimentally tackle a number of air pollution problems, especially those related to odor impact. Their small size and cost permit a denser sampling design and thus a more detailed spatial characterization than other techniques. On the other hand, the large inherent variability in passive sampler measures requires an uncertainty analysis of the chemical species and analytical procedures used.     

The Recovery of Ammonia and Hydrogen Sulflde from Ground-Level Area Sources Using Dynamic Isolation Flux Chambers: Bench-Scale Studies

Abstract

Controlled bench-scale laboratory experiments were conducted to evaluate the recovery of ammonia (NH₃) and hydrogen sulflde (H₂S) from dynamic isolation flux chambers. H₂S (80–4000 ppb) and NH₃ (5000–40,000 ppb) samples were diffused through the flux chamber to simulate ground level area source emissions while measuring the inlet and outlet flux chamber concentrations simultaneously. Results showed that the recovery of H₂S during a 30-min sampling time was almost complete for concentrations >2000 ppb. At the lowest concentration of 80 ppb, 92.55% of the H₂S could be recovered during the given sampling period. NH₃ emissions exhibited similar behavior between concentrations of 5000–40,000 ppb. Within the 30-min sampling period, 92.62% of the 5000-ppb NH₃ sample could be recovered. Complete recovery was achieved for concentrations >40,000 ppb. Predictive equations were developed for gas adsorption. From these equations, the maximum difference between chamber inlet and outlet concentrations of NH₃ or H₂S was predicted to be 7.5% at the lowest concentration used for either gas. In the calculation of emission factors for NH₃ and H₂S, no adsorption correction factor is recommended for concentrations >37,500 ppb and 2100 ppb for NH₃ and H₂S, respectively. The reported differences in outlet and inlet concentration above these ranges are outside the full-scale sensitivity of the gas sensing equipment. The use of 46–90 m of Teflon tubing with the flux chambers has apparently no effect on gas adsorption, because recovery was completed almost instantaneously at the beginning of the tests.     

Determination of PM2.5 Sulfate and Nitrate with a PC-BOSS Designed for Routine Sampling for Semi-Volatile Particulate Matter

ABSTRACT

Ambient particles contain substantial quantities of material that can be lost from the particles during sample collection on a filter. These include ammonium nitrate and semi-volatile organic compounds. As a result, the concentrations of these species are often significantly in error for results obtained with a filter pack sampler. The accurate measurement of these semi-volatile fine particulate species is essential for a complete understanding of the possible causes of health effects associated with exposure to fine particles. Past organic compound diffusion denuder samplers developed by the authors (e.g., the Brigham Young University Organic Sampling System [BOSS]) are not amenable to routine field use because of the need to independently determine the gas-phase semi-volatile organic material efficiency of the denuder for each sample. This problem has been eliminated using a combined virtual impactor, particle-concentrator inlet to provide a concentrated stream of 0.1-2.5-μm particles. This is followed by a BOSS diffusion denuder and filter packs to collect particles, including any semi-volatile species lost from the particles during sampling. The samp ler (Particle Concentrator-Brigham Young University Organic Sampling System [PC-BOSS]) contains a post-denuder multifilter pack unit to allow for the routine collection of several sequential samples. The PC-BOSS can be used for the determination of both fine particulate nitrate and semi-volatile organic material without significant “positive” or “negative” sampling artifacts. Validation of the sampler for the determination of PM_2.5 sulfate and nitrate based on comparison of results obtained at Riverside, CA with collocated PC-BOSS, annular denuder, and Chem Spec samplers indicates the PC-BOSS gives accurate results for these species with a precision of ±5-8%. An average of 33% of the PM_2.5 nitrate was lost from the particles during sampling for both denuder and single filter samplers.     

Ammonia emissions from livestock industries in Canada: Feasibility of abatement strategies

An updated national ammonia (NH₃) emissions inventory was employed to study the relationship between NH₃ emissions and livestock industries in Canada. Emissions from animal agriculture accounted for 322 kilotonnes (kt) or 64% of Canadian NH₃ emissions in 2002. Cattle and swine accounted for the bulk of livestock emissions. The provinces of Alberta, Ontario, Quebec, and Saskatchewan accounted for 28.1%, 22.0%, 18.7%, and 13.1% of total livestock emissions, respectively. Emissions from Ontario and Quebec were attributed to the intensive production of dairy, hogs and poultry. Dairy cattle emissions per hectolitre of milk were higher in Ontario and Québec than in other provinces, while swine emissions per livestock unit were higher than either beef or dairy cattle. A review of the abatement literature indicated diet manipulation to improve N efficiency and land spreading methods are very effective techniques to lower NH₃ emissions. Future research is required to evaluate the feasibility of biofilters and feces/urine separation methods.     

Ammonia concentrations and modeling of inorganic particulate matter in the vicinity of an egg production facility in Southeastern USA

Ammonia (NH₃) is an important base gas and can react with acidic species to form atmospheric aerosols. Due to the rapid growth of poultry and swine production in the North Carolina Coastal Plain, atmospheric NH₃ concentrations across the region have subsequently increased. Ammonia concentrations and inorganic particulate matter (PM) at four ambient stations in the vicinity of an egg production facility were measured for 1 year using PM_2.5 speciation samplers with honeycomb denuders and ion chromatography (IC). Meanwhile, concentrations of NH₃ and inorganic PM in one of the egg production houses were also simultaneously measured using a gas analyzer for NH₃ and the filter pack plus IC method for inorganic PM. An equilibrium model-ISORROPIA II was applied to predict the behavior of inorganic aerosols in response to precursor gas concentrations and environmental parameters. Average ambient NH₃ concentrations varied from 10.0 to 27.0 μg/m³, and they were negatively correlated with the distances from the ambient location to the nearest egg production house exhausts. Ambient NH₃ concentrations were higher in warm seasons than in cold seasons. Measured NH₃ concentrations agreed well with ISORROPIA II model predictions at all sampling stations. For the ambient stations, there was a good agreement in particle phase NH₄ ⁺ between the model simulation and observations. For the in-house station, the model simulation was applied to correct the overestimation of particle phase NH₄ ⁺ due to gas phase NH₃ breaking through the denuders. Changes in SO₄ ^2?, NO₃ ^?, and Cl^? yield proportional changes in inorganic PM mass. Due to the abundance of NH₃ gas in the vicinity area of the monitored farm, changes in NH₃ concentrations had a small effect on inorganic PM mass. Aerosol equilibrium modeling may be used to assess the influence of precursor gas concentrations on inorganic PM formation when the measurements for some species are unavailable.