Study on the photocatalytic reduction of dichromate and photocatalytic oxidation of dichlorvos

In this paper, dichromate and dichlorvos are selected as the deputies of inorganic and organic pollutants, respectively, and TiO2/beads is used as a photocatalyst. The effects of various parameters, such as the amount of the photocatalyst, H2O2 concentration, metal ions, anions, pH value, and organic compounds on the photocatalytic reduction of dichromate and photocatalytic oxidation of dichlorvos are studied. From the studies, the differences of the parameters effect on the photocatalytic degradation of organic and inorganic pollutants are obtained. The results show that the optimum amount of the photocatalyst used is 6.0 g cm(-3) for the photocatalytic reactions. With the addition of a small amount of H2O2, the photocatalytic reduction of dichromate is inhibited while the photocatalytic oxidation of dichlorvos is accelerated. With the addition of trace amounts of Fe3+ or Cu2+, both the reactions are accelerated, and with the addition of Zn2+ and Na+, no obvious effects on the reactions are observed. Acidic solution is favorable for the photocatalytic reduction of dichromate; and acidic and alkaline solutions are favorable for the photocatalytic oxidation of dichlorvos. Adding SO4(2-), the photocatalytic oxidation is accelerated and adding Cl- the reaction is inhibited; and with the addition of trace amounts of SO4(2-), Cl- and NO3-, no obvious effects on the photocatalytic reduction of dichromate are observed. With the addition of methanol and toluene, the photocatalytic reduction of dichromate is accelerated, and the photocatalytic oxidation of dichlorvos is inhibited. The possible roles of the additives on the reactions are also discussed.     

Non-degradable triazine substrates of atrazine and cyanuric acid hydrothermally and in supercritical water under the UV-illuminated photocatalytic cooperation

Strong oxidation by titanium dioxide photocatalysis can occur by photodegradation of organic contaminants in air and water. Some endocrine disruptors such as 2,4-dichlorophenoxy acetic acid (;;; ), 2,4-dichlorophenol (;;; ), nonylphenol (; ), bisphenol A (), diethyl phthalate (; ), etc. which can be neither biodegraded by bacteria nor degraded thermally can be degraded by TiO(2) photocatalytic treatment. However, incomplete photomineralization partly occurred, when TiO(2) photocatalytic degradation is employed for the treatment of certain endocrine disruptors. For example, no atrazine pesticide having triazine skeleton can be completely mineralized even by a photocatalytic procedure; the photodegradation of atrazine ultimately stops at the intermediate step of cyanuric acid, which cannot be photodegraded even after long illumination times ().In this study, the decomposition of atrazine and cyanuric acid was carried out with a device combining photocatalytic degradation in supercritical water (scH(2)O) or hydrothermal water (hyH(2)O). Atrazine and cyanuric acid can be degraded by the cooperation of either scH(2)O or hyH(2)O and UV illuminated TiO(2)-photocatalytic dispersed system under the fixed pressure of 23 MPa at 623 K or 683 K in a 120-ml Hastelloy batch reactor. The photocatalytic degradation method under high temperature and pressure has found appropriate for the photocatalytic oxidation of acetic acid and 2-chlorobiphenyl under continuous flow conditions at 160 degrees C and 20 atm (). In addition, the wet peroxide oxidation of PCBs by high temperature and pressure has been reported (). The main aims of this research are following. (i): the degradation of atrazine and cyanuric acid within the scH(2)O or hyH(2)O, (ii) the decomposition of atrazine and cyanuric acid catalyzed by TiO(2) particles under scH(2)O or hyH(2)O, and the synergistic effect for several reactions with TiO(2) and scH(2)O or hyH(2)O, and (iii) the mineralization yield of nitrogen and chlorine atoms concerning the chemical structures of atrazine or cyanuric acid (only nitrogen).     

Photocatalytic mineralization of glyphosate in a small-scale plug flow simulation reactor by UV/TiO2

The present work involves the photocatalytic mineralization of glyphosate on a plug flow reactor by UV/TiO(2). The effect of catalyst loading shows an optimal value (0.4 g L(-1)) which is necessary to mineralize glyphosate. The kinetic rate of glyphosate mineralization decreases with the increasing initial concentration of glyphosate, and the data can be described using the first-order model. An alkaline environment is conducive to glyphosate mineralization. The mineralization efficiency increases with elevated flow rate to 114 mL min(-1), which is followed by a decrease with a further increase in flow rate due to the reduction of the residence time. The presence of external oxidants (K(2)S(2)O(8), H(2)O(2) and KBrO(3)) and photosencitizer (humic acid) can significantly enhance glyphosate mineralization. Photocatalysis oxidation ability of the three studied oxidants decrease in the order of: S(2)O(8)(2-) > BrO(3)(-) > H(2)O(2). Finally, the Langmuir-Hinshelwood (L-H) model was used to rationalize the mechanisms of reactions occurring on TiO(2) surfaces and L-H model constants were also determined.     

Kinetics and mechanism of TNT degradation in TiO2 photocatalysis

The photocatalytic degradation of TNT in a circular photocatalytic reactor, using a UV lamp as a light source and TiO(2) as a photocatalyst, was investigated. The effects of various parameters such as the initial TNT concentration, and the initial pH on the TNT degradation rate of TiO(2) photocatalysis were examined. In the presence of both UV light illumination and TiO(2) catalyst, TNT was more effectively degraded than with either UV or TiO(2) alone. The reaction rate was found to obey pseudo first-order kinetics represented by the Langmuir-Hinshelwood model. In the mineralization study, TNT (30 mg/l) photocatalytic degradation resulted in an approximately 80% TOC decrease after 150 min, and 10% of acetate and 57% of formate were produced as the organic intermediates, and were further degraded. NO(-)(3) NO(-)(2), and NH(+)(4) were detected as the nitrogen byproducts from photocatalysis and photolysis, and more than 50% of the total nitrogen was converted mainly to NO(-)(3)in the photocatalysis. However, NO(-)(3) did not adsorbed on the TiO(2) surface. TNT showed higher photocatalytic degradation efficiency at neutral and basic pH.     

Heterogeneous photocatalytic degradation of prometryn in aqueous solutions under UV-Vis irradiation

In this study, the heterogeneous photocatalytic degradation of prometryn using TiO(2) as photocatalyst was investigated. The main objectives of the study were: (I) to evaluate the kinetics of the pesticide disappearance, (II) to compare the photocatalytic efficiency of two different types of TiO(2), (III) to examine the influence of various parameters such as initial concentration of pesticide or catalyst and presence of oxidants (H(2)O(2) and K(2)S(2)O(8)), (IV) to evaluate the degree of mineralization and (V) to assess the detoxification efficiency of the studied processes. The experiments were carried out in a 500 ml pyrex UV reactor equipped with a 125 W high-pressure mercury lamp surrounded by a pyrex filter blocking wavelengths below 290 nm. Prometryn concentration was determined using HPLC. It was found that the degradation of the pesticide follows the first order kinetics according to the Langmuir-Hinshelwood model. Parameters like the type and concentration of the catalyst affect the degradation rate. A synergistic effect was observed when an oxidant was added in the TiO(2) suspensions increasing the reaction rate of photodegradation. In order to examine the extent of pesticide mineralization, DOC measurements were carried out. After 6h of illumination, mineralization was achieved up to almost 70%. The toxicity of the treated solution was evaluated using the Microtox test based on the luminescent bacteria Vibrio fisheri, in order to compare the acute toxicity of prometryn and its photoproducts. The detoxification efficiency was found to be dependent on the studied system and it did not follow the rate of pesticide disappearance.     

Photocatalytic degradation of the herbicide erioglaucine in the presence of nanosized titanium dioxide: comparison and modeling of reaction kinetics

The present work mainly deals with photocatalytic degradation of a herbicide, erioglaucine, in water in the presence of TiO2 nanoparticles (Degussa P-25) under ultraviolet (UV) light illumination (30 W). The degradation rate of erioglaucine was not so high when the photolysis was carried out in the absence of TiO2 and it was negligible in the absence of UV light. We have studied the influence of the basic photocatalytic parameters such as pH of the solution, amount of TiO2, irradiation time and initial concentration of erioglaucine on the photodegradation efficiency of erioglaucine. A kinetic model is applied for the photocatalytic oxidation by the UV/TiO2 system. Experimental results indicated that the photocatalytic degradation process could be explained in terms of the Langmuir-Hinshelwood kinetic model. The values of the adsorption equilibrium constant, K, and the second order kinetic rate constant, k, were 0.116 ppm-1 and 0.984 ppm min-1, respectively. In this work, we also compared the reactivity between the commercial TiO2 Degussa P-25 and a rutile TiO2. The photocatalytic activities of both photocatalysts were tested using the herbicide solution. We have noticed that photodegradation efficiency was different between both of them. The higher photoactivity of Degussa P-25 compared to that of rutile TiO2 for the photodegradation of erioglaucine may be due to higher hydroxyl content, higher surface area, nano-size and crystallinity of the Degussa P-25. Our results also showed that the UV/TiO2 process with Degussa P-25 as photocatalyst was appropriate as the effective treatment method for removal of erioglaucine from a real wastewater. The electrical energy consumption per order of magnitude for photocatalytic degradation of erioglaucine was lower with Degussa P-25 than in the presence of rutile TiO2.     

Photocatalytic degradation of an organophosphorus pesticide phosalone in aqueous suspensions of titanium dioxide

The present work deals with photocatalytic degradation of an organophosphorus pesticide, phosalone, in water in the presence of TiO2 particles under UV light illumination (1000 W). The influence of the basic photocatalytic parameters such as pH of the solution, amount of TiO2, irradiation time, stirring rate, and distance from UV source, on the photodegradation efficiency of phosalone was investigated. The degradation rate of phosalone was not high when the photolysis was carried out in the absence of TiO2 and it was negligible in the absence of UV light. The half-life (DT50) of a 20 ppm aqueous solution of phosalone was 15 min in optimized conditions. The plot of lnC (phosalone) vs. time was linear, suggesting first order reaction (K=0.0532 min(-1)). The half-life time of photomineralization in the concentration range of 7.5-20 ppm was 13.02 min. The efficiency of the method was also determined by measuring the reduction of Chemical Oxygen Demand (COD). During the mineralization under optimized conditions, COD decreased by more than 45% at irradiation time of 15 min. The photodegradation of phosalone was enhanced by addition of proper amount of hydrogen peroxide (150 ppm).     

ZnO/LixNi1-xO光催化降解甲基橙的研究

采用溶胶凝胶法制备LixNi1-xO和ZnO粉体,利用球磨法制备ZnO/LixNi1-xO复合粉体,以紫外光为光源,通过降解甲基橙,研究了锂掺杂及n-p复合对氧化镍的光催化性能影响。结果表明：当投放量为0.1 g/L,x≤0.075（摩尔分数）的锂掺杂氧化镍均比未掺杂氧化镍的光催化活性高。当锂掺杂摩尔分数为0.025,投放量为0.4 g/L时锂掺杂氧化镍的光催化活性最佳,甲基橙最高降解率达到93.1%。当ZnO/Li0.025Ni0.975O在质量比为1∶1,投放量为0.2 g/L时光催化活性最佳,甲基橙最高降解率达到98.1%。     

Effects of ozone on foliar leaching in Norway spruce (Picea abies L. Karst): confounding factors due to NOx production during ozone generation

Previous experiments with conifers fumigated with O(3), produced by air-operated electric discharge ozonators, have provided evidence that O(3) increases the leaching of NO(3)(-), NH(4)(+), K(+), Ca(2+), Mg(2+) and some other cations from needles, when the trees are treated with acid mist. This evidence has provided the foundation of the ozone-acid mist hypothesis of spruce decline. We report experiments with Norway spruce saplings fumigated with purified and unpurified O(3). The results show that the accumulation of NO(3)(-) in the needles arises from the rapid deposition of N(2)O(5) and HNO(3) formed from N(2) in the ozonator. An increase in removal of NH(4)(+), Na(+), Ca(2+), Mg(2+), Zn(2+) and Mn(2+) from the needles during soaking in H(2)SO(4), pH3, was also observed, which was related to the increase in NO(3)(-) but was independent of O(3) concentration. It is concluded that results of previous experiments cited in support of the ozone-acid mist hypothesis arose from effects which were at least partly caused by N(2)O(5) produced as a contaminant, and were incorrectly attributed to ozone. Other effects, such as growth stimulations, visible symptons, enhanced frost sensitivity, and infestation by pests or pathogens, which have been attributed to O(3) generated by electric discharge in air, should be interpreted with caution. Future experiments with ozone must eliminate this problem by either using O(2)-driven ozonators, or by purifying the output from air-driven ozonators using cold and/or water traps.     

新型可见光催化剂BiVO4降解中成药制药废水

以Bi(NO3)3.5H2O和NH4VO3为原料,采用水热法制备了新型可见光BiVO4催化剂,并用X-射线衍射(XRD)、扫描电子显微镜(SEM)、红外光谱(IR)和紫外-可见光漫反射光谱(UV-vis DRS)对产品进行了结构表征,并将其应用于光催化降解中成药制药废水降解反应中,通过正交实验和单因素分析,考察了催化剂用量、空气流量、溶液pH值和助氧化剂H2O2对制药废水COD去除率、脱色率的影响。实验结果表明,水热产品属于单斜晶系BiVO4,其带隙能为2.41 eV,并具有良好的可见光催化活性。对于经10倍稀释的制药废水,BiVO4添加量为2 g/L,通氧量为120 L/h,助氧化剂H2O2添加量为1 mL,不改变废水pH值,在400 W金属卤化物灯离液面11 cm照射反应180 min的条件下,制药废水的COD去除率为94.3%,脱色率为95.6%,得到了较好的降解。     

Comparison of advanced oxidation processes and identification of monuron photodegradation products in aqueous solution

The photodegradation of monuron (3-(4-chlorophenyl)-1,1-dimethylurea) in aqueous solutions under simulated solar irradiation has been conducted by different advanced oxidation processes (UV/H(2)O(2), UV/H(2)O(2)/Fe(2+), UV/H(2)O(2)/TiO(2), UV/TiO(2), dark H(2)O(2)/Fe(3+)). The degradation rates were always higher for the homogeneous catalysis in photo-Fenton reactions (UV/H(2)O(2)/Fe(2+)) compared to the heterogeneous photocatalytic systems (TiO(2)/UV and UV/H(2)O(2)/TiO(2)). Optimal concentrations of Fe(2+) and H(2)O(2) for the abatement of the herbicide in the photo-Fenton system were found to be 1 mM Fe(II) and 10 mM H(2)O(2). Several intermediary products were identified using large volume injection micro-liquid chromatography with UV detection (mu-LC-UV), mu-LC-MS and GC-MS techniques and a degradation mechanism has been proposed.     

陶瓷负载Ag、Ce共掺杂TiO2光催化剂降解甲基橙的研究

以陶瓷为载体,采用溶胶-凝胶法制备了银离子和铈离子共掺杂TiO2的负载型光催化剂——T-AC/陶瓷,研究了pH值、双氧水用量、催化剂用量、紫外灯强度、废水的初始浓度等因素对T-AC/陶瓷光催化剂降解甲基橙染料废水的影响。结果表明,当pH为2、双氧水用量为0.5 mL/100 mL、催化剂用量为3 g/L、紫外灯功率为20 W、废水初始浓度为10mg/L时,甲基橙的降解率可达85.9%,并且甲基橙的光催化降解属于一级动力学方程,T-AC/陶瓷催化剂有较高的活性和稳定性,在废水处理中具有较好的应用前景。     

Photocatalytic degradation of mixed gaseous carbonyl compounds at low level on adsorptive TiO2/SiO2 photocatalyst using a fluidized bed reactor

An adsorptive silica-supported titania photocatalyst TiO(2)/SiO(2) was prepared by using nanosized titania (anatase) immobilized on silica gel by the sol-gel technique with the titanium tetra isopropoxide as the main raw material and acetic acid as the acid catalyst. Meanwhile the structure and properties of the TiO(2)/SiO(2) photocatalyst were studied by means of many modern analysis techniques such as TEM, XRD, and BET. Gas-solid heterogeneous photocatalytic decomposition of four carbonyl compounds mixture at low concentration levels over ultraviolet irradiated TiO(2)/SiO(2) photocatalyst were carried out with high degradation efficiencies in a coaxial triple-cylinder-type fluidized bed photocatalytic reactor, which provided efficient continuous contact of ultraviolet photons, silica-supported titania photocatalyst, and gaseous reactants. Experimental results showed that the photocatalyst had a high adsorption performance and a good photocatalytic activity for four carbonyl compounds mixture. Some factors influencing the photocatalytic decomposition of the mixed carbonyl compounds, i.e. the gas flowrate, relative humidity, concentration of oxygen, and illumination time, were discussed in detail. It is found that the photocatalytic reaction rate of four carbonyl compounds decreased in this order: propionaldehyde, acetone, acetaldehyde and formaldehyde.     

Atmospheric input of elements to forest ecosystems: a method of estimation using artificial foliage placed above rain collectors

Usefulness of a method of artificial foliage was tested for estimation of total ionic inputs from the atmosphere to forest ecosystems, as well as of processes relevant to ionic fluxes through tree canopies: uptake, leaching, passive flow. The studies were performed in Norway spruce and European beech stands in Karkonosze Mountains (Poland), in 1995-97. Artificial leaves of increasing leaf area index: 0, 2, 6 and 12 m(2) m(-2 )were placed above standard rain collectors. It has been found that total atmospheric fluxes of H(+), NH(4)(+), Ca(2+), Mg(2+), Pb(2+), NO(3)(-) and SO(4)(2-) rose as surface area of the foliage increased. This was especially true for nitrate, sulphate and ammonium. No such relationship was found for K(+), Na(+), Zn(2+), Cd(2+), Cu(2+) and PO(4)(3-). The increase in anion fluxes exceeded that in neutralising cations (NH(4)(+), Na(+), K(+), Mg(2+), Ca(2+)) and led to progressive rainwater acidification with the increase in the foliage area. An analysis of net canopy exchange (atmospheric input-throughfall flux) has shown that SO(4)(2-), PO(4)(3-), Na(+), Ca(2+) and Cu(2+) flowed passively through the tree crowns; NH(4)(+), NO(3)(-), Zn(2+), Cd(2+) and occasionally Pb(2+) were efficiently absorbed, whereas K(+) was leached from the canopies. Beech was more effective in modifying ionic pool from the atmosphere than spruce. This related to H(+) (greater absorption) and Mg(2+) (greater leaching). It has been demonstrated that the results concerning trends in net canopy exchange and produced by the simple method of artificial foliage are comparable to more sophisticated techniques of the measurements. This proves the method to be useful.     

光催化降解水体异味物质2-MIB的机理

以水体异味物质2-甲基异莰醇(2-methylisoborneol,2-MIB)为研究对象,在紫外光(λ<380 nm)照射下,探讨TiO2(P25)对2-MIB的光催化降解特性及光化学作用机理。结果表明,UV/TiO2光催化体系可以有效去除水体异味物质2-MIB,紫外光照射60 min,对2-MIB的降解率达95%。同时研究了光催化降解体系介质pH,共存腐殖酸(HA)和过硫酸钾(K2S2O8)对UV/TiO2光催化体系降解2-MIB的影响,发现低浓度HA([HA]≤0.5 mg/L)可以提高2-MIB降解速率,当HA浓度高于0.5 mg/L,2-MIB降解反应受到抑制;同时当加入电子受体K2S2O8后,降解体系中活性物种羟基自由基(.OH)明显增加,提高了TiO2对2-MIB的降解能力。利用苯甲酸荧光光度法和POD-DPD显色法跟踪测定降解过程中羟基自由基(·OH)和过氧化氢(H2O2)的变化,表明光催化反应涉及·OH机理。     

Atmospheric deposition to the edge of a spruce forest in Denmark

Atmospheric deposition was measured during 1 year at the forest edge of a Norway spruce stand in Denmark. Inside the forest the deposition of H(+), Ca(2+), Mg(2+), Na(+), K(+), Cl(-), NO(3)(-), NH(4)(2) and SO(4)(2-) with canopy throughfall varies with the distance from the forest edge. The deposition at the edge is found to be 10-20 times as high as deposition to an open field and 2-8 times as high as deposition inside the stand. An exponential decrease in deposition as a function of the distance from the forest edge is found. Increased deposition of K(+) and non-sea salt Mg(2+), which mainly originates as a result of leaching from the needles may be explained by a larger leaf area index (LAI) at the forest edge. Deposition of particulate substances, especially Na(+), Cl(-), Mg(2+) and to some extent SO(4)(2-), NH(4)(+) and NO(3)(-) is increased much more than the LAI, which we believe to be caused by changes in wind movements at the forest edge.     

TiO2纳米管催化降解4，4’-二溴联苯的影响因素和动力学研究

利用TiO2纳米管催化降解水中的4，4’-二溴联苯，对催化降解过程和影响因素进行研究。结果表明，TiO2纳米管对其有较高的催化降解效率且降解过程符合Langmuir—Hinshelwood动力学模式。不同光源、4，4’-二溴联苯的初始浓度、纳米管添加量和pH值对催化降解过程都有较大影响，其中pH值的影响最为明显。反应液在中性状态下的降解率明显低于pH=1或11的情况。在pH=1时，4，4’一二溴联苯的降解率达86％。     

Keggin型Fe-Mo-Zr杂多酸盐光催化剂的制备及性能研究

利用水热合成法制备了Keggin结构的Fe-Mo-Zr杂多酸盐光催化剂，并利用红外光谱（IR）对催化剂进行了表征。实验以酸性大红（GR）为模拟污染物，考察了在紫外灯照射下，Fe-Mo-Zr杂多酸盐的投加量、污染物的浓度和pH值以及外加H₂O₂对光催化降解效果的影响。实验结果表明，当催化剂的投加量为0.6 g/L，pH为5～7，初始浓度为10 mg/L的GR染料溶液，光照160 min，脱色率可达87.98%。外加H₂O₂可以提高光催化反应效率。     

Photocatalytic degradation of acetaminophen in modified TiO2 under visible irradiation

This study investigated the photocatalytic degradation of acetaminophen (ACT) in synthetic titanium dioxide (TiO₂) solution under a visible light (λ >440 nm). The TiO₂ photocatalyst used in this study was synthesized via sol–gel method and doped with potassium aluminum sulfate (KAl(SO₄)₂) and sodium aluminate (NaAlO₂). The influence of some parameters on the degradation of acetaminophen was examined, such as initial pH, photocatalyst dosage, and initial ACT concentration. The optimal operational conditions were also determined. Results showed that synthetic TiO₂ catalysts presented mainly as anatase phase and no rutile phase was observed. The results of photocatalytic degradation showed that LED alone degraded negligible amount of ACT but with the presence of TiO₂/KAl(SO₄)₂, 95 % removal of 0.10-mM acetaminophen in 540-min irradiation time was achieved. The synthetic TiO₂/KAl(SO₄)₂ presented better photocatalytic degradation of acetaminophen than commercially available Degussa P-25. The weak crystallinity of synthesized TiO₂/NaAlO₂ photocatalyst showed low photocatalytic degradation than TiO₂/KAl(SO₄)₂. The optimal operational conditions were obtained in pH 6.9 with a dose of 1.0 g/L TiO₂/KAl(SO₄)₂ at 30 °C. Kinetic study illustrated that photocatalytic degradation of acetaminophen fits well in the pseudo-first order model. Competitive reactions from intermediates affected the degradation rate of ACT, and were more obvious as the initial ACT concentration increased.     

Effect of the carbon coating in Fe-C-TiO(2) photocatalyst on phenol decomposition under UV irradiation via photo-Fenton process

Fe-C-TiO(2) photocatalysts which contained the residue carbon (0.2-3.3 mass%) were prepared from a mixture of TiO(2) and FeC(2)O(4) through the heating at 673-1173 K in Ar. These photocatalysts did not show a high adsorption of phenol, but they were active in photo-Fenton reactions during decomposition of phenol under UV irradiation with addition of H(2)O(2). It was proved that Fe(2+) governed the photoactivity of Fe-C-TiO(2) photocatalysts, it decreased with heat-treatment temperature above 773 K. For comparison, Fe-TiO(2) photocatalyst was prepared by heating TiO(2) and FeC(2)O(4) at 823 K in air for 3h. Phenol decomposition was going much slower on Fe-TiO(2) photocatalyst in comparison with Fe-C-TiO(2), of which mechanism was different, on the former phenol was decomposed by the radical reaction, on the latter through a complex reaction with iron and intermediates of phenol decomposition. Therefore carbon-coating TiO(2) was found to be advantageous for mounting iron and its application for the phenol decomposition via photo-Fenton process.