Fate and degradation of triasulfuron in soil and water under laboratory conditions

The behavior and fate of triasulfuron (TRS) in water and soil systems were examined in laboratory studies. The degradation of TRS in both buffer solution and soil was highly pH-sensitive. The rate of degradation could be described with a pseudo first-order kinetic and was much faster at pH 4 than at pH 7 and 9. Aqueous hydrolysis occurred by cleavage of the sulfonylurea bridge to form 2-(2-chloroethoxy) benzenesulfonamide (CBSA) and [(4-methoxy-6-methyl-1,3,5-triazin-2-yl)amino] (AMMT). AMMT was unstable in aqueous solutions in any pH condition but it degraded more quickly at pH 4 and 9. CBSA did not degrade in aqueous solutions or in enriched cultures but it underwent a quick degradation in the soil. The rates of TRS degradation in sterile and non-sterile soils were similar, suggesting that microorganisms played a minimal role in the breakdown process. This hypothesis is supported by the results of studies on the degradation of TRS by enriched cultures during which the molecule underwent a prevalently chemical degradation.     

Biodegradation of endosulfan-contaminated soil in a pilot-scale reactor-bioaugmented with mixed bacterial culture

A novel mixed bacterial culture was enriched from an endosulfan (6, 7, 8, 9, 10, 10 - hexachloro-1, 5, 5a, 6, 9, 9a-hexahydro-6, 9-methano-2, 3, 4-benzo (e) dioxathiepin-3-oxide) processing industrial surface soil. The cultures were successful in the degradation of aqueous phase endosulfan in both aerobic and anaerobic conditions. Using the cultures, endosulfan degradation in silty gravel with sand (GM) was examined via pilot scale reactor at an endosulfan concentration of 0.78 +/- 0.01 mg g(- 1) of soil, and optimized moisture content of 40 +/- 1%. During operation, vertical spatial variability in endosulfan degradation was observed within the reactor. At the end of 56 days, maximum endosulfan degradation efficiency of 78 +/- 0.2% and 86.91 +/- 0.2% was observed in the top and bottom portion of the reactor, respectively. Both aerobic and anaerobic conditions were observed within the reactor. However, endosulfan degradation was predominant in anaerobic condition and the total protein concentration in the reactor was declined progressively down the soil depth. Throughout the study, no known intermediate metabolites of endosulfan reported by previous researchers were observed.     

Biodegradation of endosulfan-contaminated soil in a pilot-scale reactor-bioaugmented with mixed bacterial culture

A novel mixed bacterial culture was enriched from an endosulfan (6, 7, 8, 9, 10, 10 – hexachloro-1, 5, 5a, 6, 9, 9a-hexahydro-6, 9-methano-2, 3, 4-benzo (e) dioxathiepin-3-oxide) processing industrial surface soil. The cultures were successful in the degradation of aqueous phase endosulfan in both aerobic and anaerobic conditions. Using the cultures, endosulfan degradation in silty gravel with sand (GM) was examined via pilot scale reactor at an endosulfan concentration of 0.78 ± 0.01 mg g^{? 1} of soil, and optimized moisture content of 40 ± 1%. During operation, vertical spatial variability in endosulfan degradation was observed within the reactor. At the end of 56 days, maximum endosulfan degradation efficiency of 78 ± 0.2% and 86.91 ± 0.2% was observed in the top and bottom portion of the reactor, respectively. Both aerobic and anaerobic conditions were observed within the reactor. However, endosulfan degradation was predominant in anaerobic condition and the total protein concentration in the reactor was declined progressively down the soil depth. Throughout the study, no known intermediate metabolites of endosulfan reported by previous researchers were observed.     

Photochemical transformations of tetrabromobisphenol A and related phenols in water

A method was developed for studies of the phototransformation at UV irradiation of aqueous solutions of tetrabromobisphenol A (TBBPA), tribromobisphenol A (TriBBPA), tetrachlorobisphenol A (TCBPA), 2,4-dichlorophenol at various pHs as well as 2-chlorophenol, 2-bromophenol, 3,4-dichlorophenol and bisphenol A at pH 11. The absorbance spectra of the compounds and the emission spectra of the light-source were determined and used to calculate disappearance quantum yields of the photochemical reactions that were taking place. No major differences between the disappearance quantum yields of TBBPA and TCBPA were observed at pH 10, while the disappearance quantum yield of TriBBPA was approximately two times higher. The rate of decomposition of TBBPA was six times higher at pH 8 than at pH 6. Identification of the degradation products of TBBPA and TriBBPA, by GC-MS analysis and by comparison to synthesised reference compounds, indicated that TBBPA and TriBBPA decompose via different mechanisms. Three isopropylphenol derivatives; 4-isopropyl-2,6-dibromophenol, 4-isopropylene-2,6-dibromophenol and 4-(2-hydroxyisopropyl)-2,6-dibromophenol, were identified as major degradation products of TBBPA while the major degradation product of TriBBPA was tentatively identified as 2-(2,4-cyclopentadienyl)-2-(3,5-dibromo-4-hydroxyphenyl)propane.     

Sorption, degradation and mobility of ptaquiloside, a carcinogenic Bracken (Pteridium sp.) constituent, in the soil environment

Ptaquiloside (PTA) is a carcinogenic norsesquiterpene glucoside produced by Bracken in amounts up to at least 500 mg m(-2). The toxin is transferred from Bracken to the underlying soil from where it may leach to surface and groundwater's impairing the quality of drinking water. The objectives of the present study were to characterize the solubility, degradation and retention of PTA in soils in order to evaluate the risk for groundwater contamination. PTA was isolated from Bracken. The logarithmic octanol-water and ethyl acetate-water partitioning coefficients for PTA were -0.63 and -0.88, respectively, in agreement with the high water solubility of the compound. PTA hydrolysed rapidly in aqueous solution at pH 4 or lower, but was stable above pH 4. Incubation of PTA with 10 different soils at 25 degrees C showed three different first order degradation patterns: (i) rapid degradation observed for acid sandy soils with half life's ranging between 8 and 30 h decreasing with the soil content of organic matter, (ii) slow degradation in less acid sandy soils with half-lives of several days, and (iii) fast initial degradation with a concurrent solid phase-water partitioning reaction observed for non-acid, mostly clayey soils. The presence of clay silicates appears to retard the degradation of PTA, possibly through sorption. Degradation at 4 degrees C was generally of type (iii) and degradation rates were up to 800 times lower than at 25 degrees C. Sorption isotherms for the same set of soils were almost linear and generally showed very low sorption affinity with distribution coefficients in the range 0.01-0.22 l kg(-1) at a solution concentration of 1 mg l(-1) except for the most acid soil; Freundlich affinity coefficients increased linearly with clay and organic matter contents. Negligible sorption was also observed in column studies where PTA and a non-sorbing tracer showed almost coincident break-through. Leaching of PTA to the aqueous environment will be most extensive on sandy soils, having pH >4 and poor in organic matter which are exposed to high precipitation rates during cold seasons.     

Kinetics of the biodegradation pathway of endosulfan in the aerobic and anaerobic environments

The enriched mixed culture aerobic and anaerobic bacteria from agricultural soils were used to study the degradation of endosulfan (ES) in aqueous and soil slurry environments. The extent of biodegradation was ∼95% in aqueous and ∼65% in soil slurry during 15 d in aerobic studies and, ∼80% in aqueous and ∼60% in soil slurry during 60 d in anaerobic studies. The pathways of aerobic and anaerobic degradation of ES were modeled using combination of Monod no growth model and first order kinetics. The rate of biodegradation of β-isomer was faster compared to α-isomer. Conversion of ES to endosulfan sulfate (ESS) and endosulfan diol (ESD) were the rate limiting steps in aerobic medium and, the hydrolysis of ES to ESD was the rate limiting step in anaerobic medium. The mass balance indicated further degradation of endosulfan ether (ESE) and endosulfan lactone (ESL), but no end-products were identified. In the soil slurries, the rates of degradation of sorbed contaminants were slower. As a result, net rate of degradation reduced, increasing the persistence of the compounds. The soil phase degradation rate of β-isomer was slowed down more compared with α-isomer, which was attributed to its higher partition coefficient on the soil.     

Remediation of DDT-contaminated water and soil by using pretreated iron byproducts from the automotive industry

The objective of this study was to quantify the effectiveness of different pretreated iron byproducts from the automotive industry to degrade DDT [(1,1,1-trichloro-2,2-bis(4-chlorophenyl) ethane] in aqueous solutions and soil slurry. Iron byproducts from automotive manufacturing were pretreated by three different methods (heating, solvent and 0.5N HCl acid washing) prior to experimentation. All pretreated irons were used at 5% (wt v-1) to treat 0.014 mM (5 mgL-1) of DDT in aqueous solution. Among the pretreated irons, acid pretreated iron results in the fastest destruction rates, with a pseudo first-order degradation rate of 0.364 d-1. By lowering the pH of the DDT aqueous solution from 9 to 3, destruction kinetic rates increase more than 20%. In addition, when DDT-contaminated soil slurry (3.54 mg kg-1) was incubated with 5% (wt v-1) acid-pretreated iron, more than 90% destruction of DDT was observed within 8 weeks. Moreover, DDT destruction kinetics were enhanced when Fe(II), Fe(III) or Al(III) sulfate salts were added to the soil slurry, with the following order of destruction kinetics: Al(III) sulfate > Fe(III) sulfate > Fe(II) sulfate. These results provide proof-of concept that inexpensive iron byproducts of the automotive industry can be used to remediate DDT-contaminated water and soil.     

Study of metabolites from the degradation of polycyclic aromatic hydrocarbons (PAHs) by bacterial consortium enriched from mangrove sediments

The PAH metabolites produced during degradation of fluorene, phenanthrene and pyrene by a bacterial consortium enriched from mangrove sediments were analyzed using the on-fiber silylation solid-phase microextraction (SPME) combining with gas chromatography–mass spectrometry (GC–MS) method. Seventeen metabolites at trace levels were identified in different PAH degradation cultures based on the full scan mass spectra. In fluorene degradation cultures, 1-, 2-, 3- and 9-hydroxyfluorene, fluorenone, and phthalic acid were detected. In phenanthrene and pyrene degradation cultures, various common metabolites such as phenanthrene and pyrene dihydrodiols, mono-hydroxy phenanthrene, dihydroxy pyrene, lactone and 4-hydroxyphenanthrene, methyl ester, and phthalic acid were found. The detection of various common and novel metabolites demonstrates that SPME combining with GC–MS is a quick and convenient method for identification as well as monitoring the real time changes of metabolite concentrations throughout the degradation processes. The knowledge of PAH metabolic pathways and kinetics within indigenous bacterial consortium enriched from mangrove sediments contributes to enhance the bioremediation efficiency of PAH in real environment.     

Formation of volatile halogenated by-products during chlorination of isoproturon aqueous solutions

The present paper deals with the formation of volatile halogenated by-products (POX) during the chlorination (160 mg/l) of aqueous solutions of the herbicide isoproturon (40 mg/l). Chlorination reactions have been carried out over 48 h, at ambient temperature, at two pHs (6 and 9) and in the presence or not of bromide ions (80 mg/l). The main results obtained have been as follows: (1) in the presence of bromide, isoproturon degradation is rather fast and it results affected by pH, complete isoproturon degradation is achieved within 1 and 15 min at pH 6 and 9, respectively; (2) in the absence of bromide herbicide degradation is slow (complete degradation is achieved within 180 min) and it is not affected by pH; (3) at pH 6, regardless of the presence of bromide, the maximum amount of POX formed is low (approximately 15 micromol X-/l) and remains constant during the reaction; (4) at pH 9 the amount of POX formed is far greater and continuously increases during the reaction, reaching a value of about 110 micromol X-/l after 48 h; (5) two different groups of by-products have been identified by solid phase micro extraction (SPME)-gas chromatography (GC)-mass spectrometry (MS) for the reactions carried out with or without bromide; among them, aliphatic as well as aromatic by-products containing chlorine, bromine or both halogens are present even though the most abundant are halogenated-methane derivatives (haloforms); pH value affects the amount of these by-products but does not modify their chemical nature.     

Behavior of Chlorpyrifos-methyl in soil and sediment

This research was carried out with the aim of obtaining information regarding the possible environmental impact of Chlorpyrifos-methyl, an organophosphoric insecticide used in agriculture for its phytoiatric action against Hemiptera, Lepidoptera, Coleoptera, and Diptera. Studies relating to the degradation kinetics of the insecticide in two soils and one sediment have shown a rapid degradation process in all three. The prevalent form of degradation would appear to be the chemical type, because the degradation kinetics in a sterile soil have not demonstrated that micro-organisms play a significant part. The adsorption isotherms showed that the insecticide has a greater affinity for the sediment (Kf=143) as opposed to the soils (Kf=65) and that the adsorption process is practically irreversible. Moreover, hydrolysis tests in buffered solutions at pH 4, 7, and 9 revealed that the molecule is particularly unstable with a basic pH.     

Remediation of DDT-Contaminated Water and Soil by Using Pretreated Iron Byproducts from the Automotive Industry

The objective of this study was to quantify the effectiveness of different pretreated iron byproducts from the automotive industry to degrade DDT [(1,1,1-trichloro-2,2-bis(4-chlorophenyl) ethane] in aqueous solutions and soil slurry. Iron byproducts from automotive manufacturing were pretreated by three different methods (heating, solvent and 0.5N HCl acid washing) prior to experimentation. All pretreated irons were used at 5% (wt v^{? 1}) to treat 0.014 mM (5 mgL^{? 1}) of DDT in aqueous solution. Among the pretreated irons, acid pretreated iron results in the fastest destruction rates, with a pseudo first-order degradation rate of 0.364 d^{? 1}. By lowering the pH of the DDT aqueous solution from 9 to 3, destruction kinetic rates increase more than 20%. In addition, when DDT-contaminated soil slurry (3.54 mg kg^{? 1}) was incubated with 5% (wt v^{? 1}) acid-pretreated iron, more than 90% destruction of DDT was observed within 8 weeks. Moreover, DDT destruction kinetics were enhanced when Fe(II), Fe(III) or Al(III) sulfate salts were added to the soil slurry, with the following order of destruction kinetics: Al(III) sulfate > Fe(III) sulfate > Fe(II) sulfate. These results provide proof-of concept that inexpensive iron byproducts of the automotive industry can be used to remediate DDT-contaminated water and soil.     

Pyrene biodegradatin in aqueous solutions and soil slurries by Mycobacterium PYR-1 and enriched consortium

To better understand complex bioavailability issues, pyrene degradation was examined in aqueous and soil slurry solutions using pure Mycobacterium sp. PYR-1 and a microbial consortium. The intrinsic rates of the aqueous pyrene degradation were very similar, 1.3 x 10(-9) microg pyrene/CFU-h for Mycobacterium sp. PYR-1 and 1.1 x 10(-9) microg pyrene/CFU-h for the consortium. Rates were much lower with the soil-slurry experiments, ranging from 1.2 x 10(-12) to 7.8 x 10(-10) microg/CFU-h, depicting the strong negative effects of soils on bioavailability. Supernatants from the slurry experiments were found to increase the aqueous-phase pyrene solubility significantly. Pyrene solubility was increased from 120.5 to over 230 microg/l. However, the linear adsorption constants of pyrene on the soil were reduced.     

Bioavailability and mass balance studies of a commercial pentabromodiphenyl ether mixture in male Sprague-Dawley rats

Cyanogenic glycosides are common plant toxins. Toxic hydrogen cyanide originating from cyanogenic glycosides may affect soil processes and water quality. In this study, hydrolysis, degradation and sorption of dhurrin (4-hydroxymandelonitrile-beta-d-glucoside) produced by sorghum has been studied in order to assess its fate in soil. The log K(ow) of dhurrin was -1.18+/-0.08 (22 degrees C). Hydrolysis was a first-order reaction with respect to dhurrin and hydroxyl ion concentrations. Half lives ranged from 1.2h (pH 8.6; 25 degrees C) to 530d (pH 4; 25 degrees C). The activation energy of hydrolysis was 112+9kJ. At pH 5.8 and room temperature, addition of humic acids (50gl(-1)) increased the rate of hydrolysis tenfold, while addition of kaolinite or goethite (100-250gl(-1)) both decreased the rate considerably. No significant sorption to soil components could be observed. The degradation rates of dhurrin in top and subsoils of Oxisols, Ultisols, Alfisols and Mollisols were studied at 22 degrees C (25mgl(-1), soil:liquid 1:1 (w:V), pH 3.8-8.1). Half-lives were 0.25-2h for topsoils, and 5-288h in subsoils. Hydrolysis in solution explained up to 45% of the degradation in subsoils whereas the contribution in topsoils was less than 14%, indicating the importance of enzymatic degradation processes. The highest risk of dhurrin leaching will take place when the soil is a low activity acid shallow soil with low content of clay minerals, iron oxides and humic acids.     

Behavior of fenhexamid in soil and water

A study was conducted to investigate fenhexamid (FEX) behavior in soil and in water. FEX proved to be rather stable at acid pH but showed slight degradation at neutral and alkaline pH. After 101 days of FEX spiking of a soil sample, 94% at pH 4, 12% at pH 7 and 23% at pH 9 of the active ingredient was still present. In natural water the rate of FEX disappearance appeared to be slow which may be due to abiotic rather than biotic processes. The soil degradation tests showed low persistence of the active ingredient if a good microflora activity is guaranteed (DT(50) about 1 day). Moreover, in absence of microorganisms, FEX proved to be stable. Humidities of 25 and 50% of Water Holding Capacity (WHC) influenced in equal measure the rate of degradation. From the same soil, a bacterium was isolated and identified as Bacillus megaterium, which was able to metabolize FEX with the hydroxylation of the cyclohexane ring. Moreover, FEX showed an elevated affinity for humic acid (73%), smectite (31%), and ferrihydrite(20%) and low affinity for vermiculite (11%) and kaolinite (7%).     

Kinetics of heat-assisted persulfate oxidation of methyl tert-butyl ether (MTBE)

The kinetics of heat-assisted persulfate oxidation of methyl tert-butyl ether (MTBE) in aqueous solutions at various pH, temperature, oxidant concentration and ionic strength levels was studied. The MTBE degradation was found to follow a pseudo-first-order decay model. The pseudo-first-order rate constants of MTBE degradation by persulfate (31.5 mM) at pH 7.0 and ionic strength 0.11 M are approximately 0.13 x 10(-4), 0.48 x 10(-4), 2.4 x 10(-4) and 5.8 x 10(-4) S(-1) at 20, 30, 40 and 50 degrees C, respectively. Under the above reaction conditions, the reaction has an activation energy of 24.5 +/- 1.6 kcal/ mol and is influenced by temperature, oxidant concentration, pH and ionic strength. Raising the reaction temperature and persulfate concentration may significantly accelerate the MTBE degradation. However, increasing both pH (over the range of 2.5-11) and ionic strength (over the range of 0.11-0.53 M) will decrease the reaction rate. Reaction intermediates including tert-butyl formate, tert-butyl alcohol, acetone and methyl acetate were observed. These intermediate compounds were also degraded by persulfate under the experimental conditions. Additionally, MTBE degradation by persulfate in a groundwater was much slower than in phosphate-buffer solutions, most likely due to the presence of bicarbonate ions (radical scavengers) in the groundwater.     

Degradation of isoxaben in soils and an aqueous system.

The degradation of isoxaben [N-[3-(1-ethyl-1-methylpropyl)-5-isoxazolyl]-2,6-dimethoxybenzamide] was studied in soil and in an aqueous system. Soil studies were conducted in Erlenmeyer flasks (treated with 1 microg/g isoxaben) and mineralization studies in Biometer flasks (treated with 1 microg/g unlabeled and 14C-isoxaben) incubated at 23 C. Degradation in the aqueous system was performed in Erlenmeyer flasks under aerobic and anaerobic conditions incubated at 23 degrees C. Incubation mixtures were extracted at selected times and analyzed for isoxaben and degradation products by HPLC with product identification confirmed by GC-MS. After 8 weeks, 78% and 23% of the total isoxaben disappeared in nonsterile and sterile soils, respectively. After 12 weeks, approximately 1% of the labeled isoxaben was recovered as CO2 in the Biometer flask experiments; no volatile products were detected, and 5% and 33% of the total radioactivity was recovered from the nonsterile and sterile soils, respectively. In the aquatic system after 8 weeks, isoxaben had decreased from 1microg/g to 0.1 and 0.004 microg/g under aerobic and anaerobic conditions, respectively. Degradation products detected from the soil studies were 3-nitrophthalic acid and 4-methoxyphenol, and 3-nitrophthalic acid in the aqueous system studies. Microbial activity was considered to be a major factor in the degradation of isoxaben in this study.     

Photochemical behaviour of carbendazim in aqueous solution

To elucidate the photochemical behaviour of carbendazim (or MBC) in superficial waters, photolysis studies have been carried out in aqueous solutions at several pH using a UV light source (high pressure mercury arc lamp) or a solar light simulator (xenon arc lamp). The kinetics of photodecomposition of carbendazim was determined using HPLC-DAD and the identification of photoproducts was carried out with HPLC-MS (ESI negative and positive mode). According to the experimental results carbendazim is a rather stable molecule in the dark or in environmental conditions. The pH influence of the environmental medium on the photodegradation rate has been confirmed. The photochemical process can be considerably accelerated in alkaline solutions using HPK-quartz irradiation (quantum efficiency at pH 9 phi = 3.1 x 10(-3) degraded molecule per absorbed photon) while the photodegradation is not as efficient under a simulated sun irradiation (quantum efficiency in the suntest phi = 10(-4) at pH 7). Three photoproducts have been tentatively identified in pure water: 2-aminobenzimidazole, benzimidazole isocyanate and monocarbomethoxy-guanidine (issued from the cleavage of the benzimidazole ring). The last one seems very stable and could be accumulated in the environment.     

Behavior of fenhexamid in soil and water

A study was conducted to investigate fenhexamid (FEX) behavior in soil and in water. FEX proved to be rather stable at acid pH but showed slight degradation at neutral and alkaline pH. After 101 days of FEX spiking of a soil sample, 94% at pH 4, 12% at pH 7 and 23% at pH 9 of the active ingredient was still present. In natural water the rate of FEX disappearance appeared to be slow which may be due to abiotic rather than biotic processes. The soil degradation tests showed low persistence of the active ingredient if a good microflora activity is guaranteed (DT₅₀ about 1 day). Moreover, in absence of microorganisms, FEX proved to be stable. Humidities of 25 and 50% of Water Holding Capacity (WHC) influenced in equal measure the rate of degradation. From the same soil, a bacterium was isolated and identified as Bacillus megaterium, which was able to metabolize FEX with the hydroxylation of the cyclohexane ring. Moreover, FEX showed an elevated affinity for humic acid (73%), smectite (31%), and ferrihydrite(20%) and low affinity for vermiculite (11%) and kaolinite (7%).     

Degradation in soil and water and ecotoxicity of rimsulfuron and its metabolites.

The degradation and ecotoxicity of sulfonylurea herbicide rimsulfuron and its major metabolites were examined in batch samples of an alluvial sandy loam and in freshwater. An HPLC-DAD method was adapted to simultaneously identify and quantify rimsulfuron and its metabolites, which was successfully validated by GC-MS analysis. In aqueous solutions, pure rimsulfuron was rapidly hydrolyzed into metabolite 1 (N-(4,6-dimethoxypyrimidin-2-yl)-N-(3-(ethylsulfonyl)-2-pyridinylurea)), which itself was transformed into the more stable metabolite 2 (N-((3-(ethylsulfonyl)-2-pyridinyl)-4,6-dimethoxy-2-pyrimidineamine)), with half-life (t(1/2)) values of 2 and 2.5 days, respectively. Hydrolysis was instantaneous under alkaline conditions (pH = 10). In aqueous suspensions of the alluvial soil (pH = 8), formulated rimsulfuron had a half-life of 7 days, whereas that of metabolite 1 was similar to that in water (about 3.5 days). The degradation of the two major metabolites was also studied in soil suspensions with the pure compounds at concentrations ranging from 1 to 10 mg l(-1). The half-life of metabolite 1 ranged from 3.9 to 5 days, close to the previous values. Metabolite 2 was more persistent and its degradation is strongly dependent on the initial concentration (C0): half-life values ranged from 8.1 to 55 days at 2-10 mg l(-1), respectively. These values are higher than those determined from the kinetics of metabolite 1 transformation into metabolite 2 (t(1/2) = 8-19 days). The ecotoxicity of the three chemicals was evaluated through their effect on Daphnia magna and Vibrio fischeri (Microtox bioassay). No effect was observed on D. magna with 24 and 48 h acute toxicity tests. Similarly, no toxic effect was observed with the Microtox test for the three chemicals in the range of concentrations tested that included the field application dose. Thus, being of low persistence and lacking acute toxicity, these chemicals present a low environmental risk. However, chronic effects should be studied in order to confirm the safety of rimsulfuron and its major metabolites.     

Enhanced degradation of polycyclic aromatic hydrocarbons by biodegradation combined with a modified Fenton reaction

A study has been conducted to enhance degradation of a mixture of polycyclic aromatic hydrocarbons (PAHs) by combining biodegradation with hydrogen peroxide oxidation in a former manufactured gas plant (MGP) soil. An active bacterial consortium enriched from the MGP surface soil (0-2 m) biodegraded more than 90% of PAHs including 2-, 3-, and 4-ring hydrocarbons in a model soil. The consortium was also able to transform about 50% of 4- and 5-ring hydrocarbons in the MGP soil. As a chemical oxidant, Fenton's reagent (H2O2 + Fe2+) was very efficient in the destruction of a mixture of PAHs (i.e., naphthalene (NAP), fluorene (FLU), phenanthrene (PHE), anthracene (ANT), pyrene (PYR), chrysene (CHR), and benzo(a)pyrene (BaP)) in the model soil; noticeably, 84.5% and 96.7% of initial PYR and BaP were degraded, respectively. In the MGP soil, the same treatment destroyed more than 80% of 2- and 3-ring hydrocarbons and 20-40% of 4- and 5-ring compounds. However, the low pH requirement (pH 2-3) for optimum Fenton reaction made the process incompatible with biological treatment and posed potential hazards to the soil ecosystem where the reagent was used. In order to overcome such limitation, a modified Fenton-type reaction was performed at near neutral pH by using ferric ions and chelating agents such as catechol and gallic acid. By the combined treatment of the modified Fenton reaction and biodegradation, more than 98% of 2- or 3-ring hydrocarbons and between 70% and 85% of 4- or 5-ring compounds were degraded in the MGP soil, while maintaining its pH about 6-6.5.