Sustainability assessment of large-scale ethanol production from sugarcane

The present study assesses the sustainability of ethanol produced from sugarcane and examines the environmental feasibility of a large-scale production through the use of: fossil fuel embodied energy and Emergy Assessment including farm and industrial production phases. The study indicates that about 1.82 kg of topsoil eroded, 18.4 l of water and 1.52 m² of land are needed to produce 1 l of ethanol from sugarcane. Also, 0.28 kg of CO₂ is released per liter of ethanol produced. The energy content of ethanol is 8.2 times greater than the fossil-based energy required to produce it. The transformity of ethanol is about the same as those calculated for fossil fuels. The Renewability of ethanol is 30%, a very low value; other emergy indices indicate important environmental impacts as well as natural resources consumption. The results obtained indicate that sugarcane and ethanol production present low renewability when a large-scale system is adopted.     

Methane,nitrous oxide and ammonia emissions during storage and after application of dairy cattle slurry and influence of slurry treatment

Slurries are a significant source of CH₄, NH₃ and N₂O emissions to the atmosphere. The research project aimed at quantifying CH₄, NH₃ and N₂O emissions from liquid manure stores and after manure application under field conditions. The influence of the manure treatment options “no treatment”, “slurry separation”, “anaerobic digestion”, “slurry aeration” and “straw cover” on the emission level was investigated. Approximately 10 m³ of differently treated slurry were stored in pilot scale slurry tanks. Emissions were followed for c. 80 days. After the storage period, slurries were applied to permanent grassland. Greenhouse gas emissions from slurry were mainly caused by methane emissions during storage and by nitrous oxide emissions after field application of manures. Mitigation of GHG emissions can be achieved by a reduction in slurry dry matter and easily degradable organic matter content. Ammonia emissions mainly occurred after field application. Untreated slurry emitted 226.8 g NH₃ m⁻³ and 92.4 kg CO₂ eq. m⁻³ (storage and field application). Slurry separation (liquid fraction and composting of the solid fraction) resulted in NH₃ losses of 402.9 g m⁻³ and GHG losses of 58.5 kg CO₂ eq. m⁻³. Anaerobic digestion was a very effective means to reduce GHG emissions. 37.9 kg CO₂ eq. m⁻³ were lost. NH₃ emissions were similar to those from untreated slurry. Covering the slurry store with a layer of chopped straw instead of a wooden cover increased NH₃ emissions to 320.4 g m⁻³ and GHG emissions to 119.7 kg CO₂ eq. m⁻³. Slurry aeration nearly doubled NH₃ emissions compared to untreated slurry. GHG emissions were reduced to 53.3 kg CO₂ eq. m⁻³.     

Modelling greenhouse gas emissions from European conventional and organic dairy farms

Agriculture is an important contributor to global emissions of greenhouse gases (GHG), in particular for methane (CH₄) and nitrous oxide (N₂O). Emissions from farms with a stock of ruminant animals are particularly high due to CH₄ emissions from enteric fermentation and manure handling, and due to the intensive nitrogen (N) cycle on such farms leading to direct and indirect N₂O emissions. The whole-farm model, FarmGHG, was designed to quantify the flows of carbon (C) and nitrogen (N) on dairy farms. The aim of the model was to allow quantification of effects of management practices and mitigation options on GHG emissions. The model provides assessments of emissions from both the production unit and the pre-chains. However, the model does not quantify changes in soil C storage.Model dairy farms were defined within five European agro-ecological zones for both organic and conventional systems. The model farms were all defined to have the same utilised agricultural area (50 ha). Cows on conventional and organic model farms were defined to achieve the same milk yield, so the basic difference between conventional and organic farms was expressed in the livestock density. The organic farms were defined to be 100% self-sufficient with respect to feed. The conventional farms, on the other hand, import concentrates as supplementary feed and their livestock density was defined to be 75% higher than the organic farm density. Regional differences between farms were expressed in the milk yield, the crop rotations, and the cow housing system and manure management method most common to each region.The model results showed that the emissions at farm level could be related to either the farm N surplus or the farm N efficiency. The farm N surplus appeared to be a good proxy for GHG emissions per unit of land area. The GHG emissions increased from 3.0 Mg CO₂-eq ha⁻¹ year⁻¹ at a N surplus of 56 kg N ha⁻¹ year⁻¹ to 15.9 Mg CO₂-eq ha⁻¹ year⁻¹ at a N surplus of 319 kg N ha⁻¹ year⁻¹. The farm N surplus can relatively easily be determined on practical farms from the farm records of imports and exports and the composition of the crop rotation. The GHG emissions per product unit (milk or metabolic energy) were quite closely related to the farm N efficiency, and a doubling of the N efficiency from 12.5 to 25% reduced the emissions per product unit by ca. 50%. The farm N efficiency may therefore be used as a proxy for comparing the efficiencies of farms with respect to supplying products with a low GHG emission.     

Mitigation of greenhouse gas emissions by anaerobic digestion of cattle slurry

Biogas treatment of animal manures is an upcoming technology because it is a way of producing renewable energy (biogas). However, little is known about effects of this management strategy on greenhouse gas (GHG) emissions during fermentation, storage, and field application of the substrates compared to untreated slurries. In this study, we compared cattle slurry and cattle slurry with potato starch as additive during the process of fermentation, during storage and after field application. The addition of potato starch strongly enhanced CH₄ production from 4230 l CH₄ m⁻³ to 8625 l CH₄ m⁻³ in the fermenter at a hydraulic retention time (HRT) of 29 days. Extending the HRT to 56 days had only a small effect on the CH₄ production. Methane emissions from stored slurry depended on storage temperature and were highest from unfermented slurry followed by the slurry/starch mixture. Gas emissions from untreated and fermented slurry during storage were further analyzed in a pilot-scale experiment with different levels of covering such as straw cover, a wooden lid and no cover. Emissions of greenhouse gases (CH₄, N₂O, NH₃) were in the range of 14.3–17.1 kg CO₂ eq. m⁻³ during winter (100 day storage period) and 40.5–90.5 kg CO₂ eq. m⁻³ during summer (140 day storage period). A straw cover reduced NH₃ losses, but not overall GHG emissions, whereas a solid cover reduced CH₄ and NH₃ emissions. After field application, there were no significant differences between slurry types in GHG emissions (4.15–8.12 kg CO₂ eq. m⁻³ a⁻¹). GHG emissions from slurry stores were more important than emissions after field application. Co-digestion of slurry with additives such as starch has a large potential to substitute fossil energy by biogas. On a biogas plant, slurry stores should be covered gas-tight in order to eliminate GHG emissions and collect CH₄ for electricity production.     

Disaggregated greenhouse gas emission inventories from agriculture via a coupled economic-ecosystem model

Estimates of regional greenhouse gas emissions from agricultural systems are needed to evaluate possible mitigation strategies with respect to environmental effectiveness and economic feasibility. Therefore, in this study, we used the GIS-coupled economic-ecosystem model EFEM–DNDC to assess disaggregated regional greenhouse gas (GHG) emissions from typical livestock and crop production systems in the federal state of Baden-Württemberg, Southwest Germany. EFEM is an economic farm production model based on linear programming of typical agricultural production systems and simulates all relevant farm management processes and GHG emissions. DNDC is a process-oriented ecosystem model that describes the complete biogeochemical C and N cycle of agricultural soils, including all trace gases.Direct soil emissions were mainly related to N₂O, whereas CH₄ uptake had marginal influence (net soil C uptake or release was not considered). The simulated N₂O emissions appeared to be highly correlated to N fertilizer application (R² = 0.79). The emission factor for Baden-Württemberg was 0.97% of the applied N after excluding background emissions.Analysis of the production systems showed that total GHG emissions from crop based production systems were considerably lower (2.6–3.4 Mg CO₂ eq ha⁻¹) than from livestock based systems (5.2–5.3 Mg CO₂ eq ha⁻¹). Average production system GHG emissions for Baden-Württemberg were 4.5 Mg CO₂ eq ha⁻¹. Of the total 38% were derived from N₂O (direct and indirect soil emissions, and manure storage), 40% were from CH₄ (enteric fermentation and manure storage), and 22% were from CO₂ (mainly fertilizer production, gasoline, heating, and additional feed). The stocking rate was highly correlated (R² = 0.85) to the total production system GHG emissions and appears to be a useful indicator of regional emission levels.     

Changes in soil fertility parameters and the environmental effects in a rapidly developing region of China

An extensive knowledge of the temporal variability of soil fertility parameters and how this variation affects the environment is imperative to a wide range of disciplines within agricultural science for optimal crop production and ecosystem preservation. This paper examines the temporal variability of soil pH, organic matter (OM), cation exchange capacity (CEC), total nitrogen (TN), total phosphorus (TP), available phosphorus (P_Av), and available potassium (K_Av) on Cambosols (Entisols) (n = 179) and Anthrosols (Inceptisols) (n = 95) in Zhangjiagang County, China from 1980 to 2004. Nutrient input was monitored from 1983 to 2004. Annual N fertilizer rates were significantly different during three periods (1983–1989, 1989–1999, 1999–2004), where annual rates increased significantly after 1989 and then decreased after 1999. Annual P fertilizer rates were significantly different during two periods (1983–1993, 1993–2004) where annual rates increased after 1993. No change was found in K fertilizer rates. Soil pH marginally increased by 0.14 units in Cambosols, but significantly decreased by 1.02 units in Anthrosols. OM, CEC, and TN increased in both soil orders an average of 2.15 g kg^?1, 1.6 cmol kg^?1, and 0.21 g kg^?1, respectively. TP decreased in Anthrosols by 70 mg kg^?1, P_Av increased in Cambosols by 4.83 mg kg^?1, and K_Av decreased in Cambosols by 15 mg kg^?1. Fertilizer input rates are causing nutrient imbalances, contributing to acidification in Anthrosols, and decreasing C/N ratios. Nutrient loading of N and deficiency of K is also a potential problem in the area. Efforts should be made to readjust soil nutrient inputs to reach an optimal, sustainable level.     

Comparing carbon fluxes between different stages of secondary succession of a karst grassland

Abandonment of marginal agricultural areas with subsequent secondary succession is a widespread type of land use change in Mediterranean and mountain areas of Europe, leading to important environmental consequences such as change in the water balance, carbon cycling, and regional climate. Paired eddy flux measurement design with grassland site and tree/shrub encroached site has been set-up in the Slovenian Karst (submediterranean climate region) to investigate the effects of secondary succession on ecosystem carbon cycling. The invasion of woody plant species was found to significantly change carbon balance shifting annual NEE from source to an evident sink. According to one year of data succession site stored ?126 ± 14 g C m^?2 y^?1 while grassland site emitted 353 ± 72 g C m^?2 y^?1. In addition, the seasonal course of CO₂ exchange differed between both succession stages, which can be related to differences in phenology, i.e. activity of prevailing plant species, and modified environmental conditions within forest fragments of the invaded site. Negligible effect of instrument heating was observed which proves the Burba correction in our ecosystems unnecessary. Unexpectedly high CO₂ emissions and large disagreement with soil respiration especially on the grassland site in late autumn indicate additional sources of carbon which cannot be biologically processes, such as degassing of soil pores and caves after rain events.     

Life-cycle environmental and economic impacts of energy-crop fuel-chains: an integrated assessment of potential GHG avoidance in Ireland

This paper combines life-cycle analyses and economic analyses for Miscanthus and willow heat and electricity fuel-chains in Ireland. Displaced agricultural land-uses and conventional fuels were considered in fuel-chain permutations. Avoided greenhouse gas (GHG) emissions ranged from 7.7 to 35.2 t CO₂ eq. ha⁻¹ a⁻¹. Most fuel-chain permutations exhibited positive discounted financial returns, despite losses for particular entities at a farm-gate processed-biomass price of €100 t⁻¹ dry-matter. Attributing a value of €10 t⁻¹ CO₂ eq. to avoided GHG emissions, but subtracting financial returns associated with displaced fuel supplies, resulted in discounted annual national economic benefits (DANEBs) ranging from −457 to 1887€ ha⁻¹ a⁻¹. Extrapolating a plausible combination of fuel-chains up to a national indicative scenario resulted in GHG emission avoidance of 3.56 Mt CO₂ eq. a⁻¹ (5.2% of national emissions), a DANEB of 167 M€, and required 4.6% of national agricultural land area. As cost-effective national GHG avoidance options, Miscanthus and willow fuel-chains are robust to variation in yields and CO₂ price, and appear to represent an efficient land-use option (e.g. compared with liquid biofuel production). Policies promoting utilisation of these energy-crops could avoid unnecessary, and environmentally questionable, future purchase of carbon credits, as currently required for national Kyoto compliance.     

Balancing of greenhouse gas emissions and economic efficiency for biogas-production through anaerobic co-fermentation of slurry with organic waste

Using the organic fraction of municipal solid waste (OFMSW) for biogas production might contribute to greenhouse gas mitigation, but emissions linked with biogas production can reduce these beneficial effects. Therefore the emissions of NH₃, CH₄ and N₂O and costs caused by treating OFMSW by co-fermentation with slurry were calculated in detail from literature data, and strategies for reducing emissions were evaluated. Emission factors were calculated for single gases during storage and after application. The sensitivity of the calculations concerning the organic dry matter content of OFMSW, retention time and CH₄-yield was analyzed. The anaerobic co-fermentation of OFMSW increased biogas yields and contributed to the reduction of CO₂ emissions with 32 to 152 kg CO₂ t⁻¹ organic waste depending on application and storage techniques used for the fermentation residues. Considering a payment of 0.1 €/kWh for the electricity produced, the costs for utilization of OFMSW in slurry based biogas plants were calculated to range between 34 and 38 € t⁻¹. Measures for mitigating greenhouse gas emissions by covering the fermentation residue stores proved to be more cost effective with 3–31 € t⁻¹ CO₂ compared to immediate harrowing or injecting the residues during field application.     

Ammonia and nitrous oxide emissions following land application of high and low nitrogen pig manures to winter wheat at three growth stages

Nitrous oxide (N₂O) and ammonia (NH₃) emissions from surface applied high (HN) and low (LN) nitrogen pig manures were measured under field conditions. Manures were band-spread to a winter wheat crop at three growth stages—mid-tillering, stem elongation and flag leaf emergence. The N₂O flux rates were measured using the static chamber technique while NH₃ volatilisation was assessed using a micrometeorological mass balance technique with passive flux samplers. The N₂O emissions were episodic in nature with flux rates observed ranging from 2.8 to 31.5 g N₂O–N ha^?1 day^?1 (P < 0.001). Higher N₂O emissions generally occurred after rainfall events. Highest N₂O losses were observed from the HN treatment with LN manure use decreasing emissions by 18% (P < 0.03). The NH₃ volatilisation rates were highest within 1 h of manure application with 95% of emissions occurring within 24 h (P < 0.001). Cumulative N loss was highest at mid-tillering as low crop canopy cover and increased wind-speeds enhanced NH₃ loss (P < 0.001). Highest emissions were measured from the HN manure (P < 0.03). Total ammoniacal N loss ranged from 6 to 11%. Crop N uptake and grain yield were unaffected by application timing or manure type. Therefore, the use of LN manures decreased gaseous emissions of N₂O and NH₃ without any adverse effects on crop performance.     

Monitoring GHG from manure stores on organic and conventional dairy farms

Organic farming methods are claimed to be more environmentally friendly than conventional methods and the EU MIDAIR project had an overall aim to compare emissions from organic dairy farming with conventional methods of milk production. Manure stores are the second largest source of methane emissions (after enteric fermentation) on European dairy farming.The aim of this project was to measure green house gas (GHG) emissions from manures in covered and uncovered slurry stores and farm yard manure (FYM) heaps. The chosen method for measuring these emissions was the tracer ratio method, using sulphur hexafluoride (SF₆) as the tracer gas, the limitations of this method prevented successful measurements being made on some of the stores and a modified method was used on the covered stores. The difference in concentration of the upwind and downwind samples and interfering sources were limiting factors. FYM emission measurements were successful only when the manure was stored indoors.Methane emissions were successfully measured over a 12 month period from the uncovered slurry stores. Emission rates from the uncovered slurry stores on the conventional farm and the organic farm ranged from 14.4 to 49.6 and from 12.4 to 42.3 g C m⁻³ d⁻¹, respectively, with the mean CH₄ emission rates of 35 and 26 g C m⁻³ d⁻¹. On both farms, nitrous oxide emissions were close to zero.Methane emissions measured from the indoor organic FYM in summer were 17.1 g C m⁻³ d⁻¹ and the nitrous oxide emission was 411 mg N m⁻³ d⁻¹.The covered slurry stores were in such close proximity to other GHG sources that the tracer ratio method was unsuitable and the air-injection method was adopted. The measured emissions from covered slurry stores of CH₄, CO₂ and NH₃ were, respectively, 14.9 g C m⁻³ d⁻¹, 12.9 g C m⁻³ d⁻¹ and 18.6 mg NH₃ m⁻² d⁻¹ of slurry in February and 12.0 g C m⁻³ d⁻¹, 9.5 g C m⁻³ d⁻¹ and 335 mg NH₃ m⁻² d⁻¹ slurry in March. No nitrous oxide production could be measured.     

Integrated environmental assessment of biodiesel production from soybean in Brazil

This paper presents the results of an environmental impact assessment of biodiesel production from soybean in Brazil. In order to achieve this objective, environmental impact indicators provided by Emergy Accounting (EA), Embodied Energy Analysis (EEA) and Material Flow Accounting (MFA) were used. The results showed that for one liter of biodiesel 8.8 kg of topsoil are lost in erosion, besides the cost of 0.2 kg of fertilizers, about 5.2 m² of crop area, 7.33 kg of abiotic materials, 9.0 tons of water and 0.66 kg of air and about 0.86 kg of CO₂ were released. About 0.27 kg of crude oil equivalent is required as inputs to produce one liter of biodiesel, which means an energy return of 2.48 J of biodiesel per Joule of fossil fuel invested. The transformity of biodiesel (3.90E + 05 seJ J^?1) is higher than those calculated for fossil fuels as other biofuels, indicating a higher demand for direct and indirect environmental support. Similarly, the biodiesel emergy yield ratio (1.62) indicates that a very low net emergy is delivered to consumers, compared to alternatives. Obtained results show that when crop production and industrial conversion to fuel are supported by fossil fuels in the form of chemicals, goods, and process energy, the fraction of fuel that can actually be considered renewable is very low (around 31%).     

The CO2 abatement cost curve for the Thailand cement industry

The cement industry is one of the largest carbon dioxide (CO₂) emitters in the Thai industry. The cement sector accounted for about 20,633 kilotonnes (ktonnes) CO₂ emissions in 2005 in Thailand. A bottom-up CO₂ abatement cost curve (ACC) is constructed in this study for the Thai cement industry to determine the potentials and costs of CO₂ abatement, taking into account the costs and CO₂ abatement of different technologies. The period of 2010–2025 is chosen as the scenario period. We analyzed 41 CO₂ abatement technologies and measures for the cement industry. Using the bottom-up CO₂ ACC model, the cost-effective annual CO₂ abatement potential for the Thai cement industry during the 15 year scenario period (2010–2025) is equal to 3095 ktonnes CO₂/year. This is about 15% of the Thai cement industry’s total CO₂ emissions in 2005. The total technical annual CO₂ abatement potential is 3143 ktonnes CO₂/year, which is about 15.2% of the Thai cement industry’s total CO₂ emissions in 2005. We also conducted a sensitivity analysis for the discount rate parameter.     

Emissions of N2O and NH3, and nitrogen leaching from direct seeded rice under different tillage practices in central China

Tillage practices affect the fate of fertilizer nitrogen (N) through influencing transformations of N, but few studies have examined N₂O and NH₃ emissions, and N leaching from different rice tillage systems. Thus the objective of this study was to assess N₂O emission, NH₃ volatilization and N leaching from direct seeded rice in conventional tillage (CT) and no-tillage (NT) production systems in the subtropical region of China during the 2008 and 2009 rice growing seasons. Treatments were established following a split-plot design of a randomized complete block with tillage practices as the main plot and N fertilizer level as the sub-plot treatment, and there were four treatments: NT + no fertilizer (NT0), CT + no fertilizer (CT0), NT + compound fertilizer (NTC) and CT + compound fertilizer (CTC), respectively. Results showed that N fertilization significantly increased (p < 0.01) N₂O emissions, NH₃ volatilization and N leaching from rice fields in both years. In general, there was no significant difference in N₂O emissions and NH₃ volatilization between NT0 and CT0 in both years, while NTC had significantly higher (p < 0.05) N₂O emissions and NH₃ volatilization compared to CTC. Over the two rice growing seasons, NTC showed 32% and 47% higher N₂O emissions, and 29% and 52% higher NH₃ losses than CTC. Higher (p < 0.05) N₂O emissions from NTC than CTC were presumably due to higher soil organic C and greater denitrification. Total N and NO₃^? concentrations were higher (p < 0.05) in CTC than NTC, but larger volumes of percolation water in NTC than CTC resulted in no significant difference in leakage of total N and NO₃^?. Hence, application of N fertilizer in combination with NT appeared to be ineffective in reducing N losses from N fertilizer in paddy fields.     

Nitrous oxide emissions from organic and conventional crop rotations in five European countries

Nitrous oxide (N₂O) emissions from agriculture are currently estimated from N inputs using emission factors, and little is known about the importance of regional or management-related differences. This paper summarizes the results of a study in which N₂O emission rates were recorded on 15–26 occasions during a 12-month period in organic and conventional dairy crop rotations in five European countries (Austria, Denmark, Finland, Italy, UK). A common methodology based on static chambers was used for N₂O flux measurements, and N₂O data were compiled together with information about N inputs (from fertilizers, N₂ fixation, atmospheric deposition and excretal returns), crop rotations and soil properties. Organic rotations received only manure as N fertilizer, while manure accounted for 0–100% of fertilizer N in conventional rotations. A linear regression model was used to examine effects of location, system and crop category on N₂O emissions, while a second model examined effects of soil properties. Nitrous oxide emissions were higher from conventional than from organic crop rotations except in Austria and, according to the statistical analysis, the differences between locations and crop categories were significant. Ammonium was significantly related to N₂O emissions, although this effect was dominated by observations from a grazing system. Despite the limited number of samplings, annual emissions were estimated by interpolation. Across the two systems and five locations there was a significant relationship between total N inputs and N₂O emissions at the crop rotation level which indicated that annually 1.6 ± 0.2% (mean ± standard error) of total N inputs were lost as N₂O, while there was a background emission of 1.4 ± 0.3 kg N₂O-N ha⁻¹ year⁻¹. Although this measurement program emphasized system effects at the expense of high temporal resolution, the results indicate that N input is a significant determinant for N₂O emissions from agricultural soils.     

Material flows in the life cycle of leather

This paper presents a study on the resource and environmental profile of leather for communicating to the consumers about the environmental burdens of leather products. The results indicate that significant environmental impacts were caused during the tanning and finishing of leather as well as the electricity production and transportation required in the life cycle. The use of fossil fuels in the production of energy has greater impact with increased emissions leading to about 15190 kg CO₂ equivalent of global warming and about 73 kg SO₂ equivalent of acidification while producing 100 m² of leather for shoe uppers. Further resource use of 174 kg of coal, 6.5 kg of fuel oil, 17.4 m³ of water and 348 kg of chemicals of which about 204 kg are hazardous are consumed, and wastewater of about 17 m³, BOD of 55 kg, COD of about 146 kg, TDS of 732 kg and solid waste of about 1445 kg are generated during the life cycle for the production of 100 m² of leather. The total solid waste generated is 1317 kg, out of which about 80% is biodegradable contributed by slaughtering, tanning and finishing stage, 14% is non-biodegradable contributed by tanning, finishing and electricity production stages and 6% is hazardous mainly from tanning and finishing stage of leather.     

Atmospheric impacts of the life cycle emissions of fuel ethanol in Brazil: based on chemical exergy

An assessment is made of the atmospheric emissions from the life cycle of fuel ethanol coupled with the cogeneration of electricity from sugarcane in Brazil. The total exergy loss from the most quantitative relevant atmospheric emission substances produced by the life cycle of fuel ethanol is 3.26E+05 kJ/t of C₂H₅OH. Compared with the chemical exergy of 1 t of ethanol (calculated as 34.56E+06 kJ), the exergy loss from the life cycle's atmospheric emission represents 1.11% of the product's exergy. The activity that most contributes to atmospheric emission chemical exergy losses is the harvesting of sugarcane through the methane emitted in burning. Suggestions for improved environmental quality and greater efficiency of the life cycle of fuel ethanol with cogenerated energy are: harvesting the sugarcane without burning, renewable fuels should be used in tractors, trucks and buses instead of fossil fuel and the transportation of products and input should be logistically optimized.     

Environmental consequences of different beef production systems in the EU

The aim of this paper is to examine the environmental consequences of beef meat production in the EU, using a life cycle approach. Four beef production systems were studied – three from intensively reared dairy calves and one from suckler herds. According to the results of the analysis, the contributions from the production of 1 kg beef meat (slaughter weight) to global warming, acidification, eutrophication, land use and non-renewable energy use were lower for beef from dairy calves than from suckler herds (16.0–19.9 versus 27.3 kg CO₂e, 101–173 versus 210 g SO₂e, 622–1140 versus 1651 g NO₃e, 16.5–22.7 versus 42.9 m²year, and 41.3–48.2 versus 59.2 MJ, respectively). The breakdown analysis helped identify the key areas in the “cradle to farm gate” beef production system where sustainable management strategies are needed to improve environmental performance. The study also included a sensitivity analysis to preliminarily estimate GHG emissions from beef production systems if land opportunity cost and land use change related to grazing and feed crop production for beef were taken into account. If so, the contribution from the production of 1 kg beef to global warming would increase by a factor of 3.1–3.9, based on a depreciation period of 20 years. This highlights the importance of taking into account the impacts of land use in assessing the environmental impacts of livestock production.     

Dairy farm CH4 and N2O emissions,from one square metre to the full farm scale

The greenhouse gas emissions from agricultural systems contribute significantly to the national budgets for most countries in Europe. Measurement techniques that can identify and quantify emissions are essential in order to improve the selection process of emission reduction options and to enable quantification of the effect of such options. Fast box emission measurements and mobile plume measurements were used to evaluate greenhouse gas emissions from farm sites. The box measurement technique was used to evaluate emissions from farmyard manure and several other potential source areas within the farm. Significant (up to 250 g CH₄ m⁻² day⁻¹and 0.4 g N₂O m⁻² day⁻¹) emissions from ditches close to stables on the farm site were found.Plume emission measurements from individual manure storages were performed at three sites. For a manure storage with 1200 m³ dairy slurry in Wageningen emission factors of 11 ± 5 g CH₄ m⁻³ manure day⁻¹ and 14 ± 8 mg N₂O m⁻³ manure day⁻¹ were obtained in February 2002.Mobile plume measurements were carried out during 4 days at distances between 30 and 300 m downwind of 20 different farms. Total farm emissions levels ranged from 14 to 95 kg CH₄ day⁻¹ for these sites. Expressed as emission per animal the levels were 0.7 ± 0.4 kg CH₄ animal⁻¹ day⁻¹ for conventional farms. For three farms that used straw bedding for the animals1.4 ± 0.2 kg CH₄ animal⁻¹ day⁻¹ was obtained. These factors include both respired methane and emission from manure in the stable and the outside storages.For a subset of these farms the CH₄ emission was compared with monthly averaged model emission calculations using FarmGHG. This model calculates imports, exports and flows of all products through the internal chains on the farm using daily time steps. The fit of modelled versus measured data has a slope of 0.97 but r² = 0.27. Measurements and model emission estimates agree well on average, for large farms within 30%. For small farms the differences can be up to a factor of 3. CH₄ emissions during winter seem to be underestimated.     

Biochar addition to agricultural soil increased CH4 uptake and water holding capacity – Results from a short-term pilot field study

Biochar addition to agricultural soil has been suggested to mitigate climate change through increased biogenic carbon storage and reduction of greenhouse gas emissions. We measured the fluxes of N₂O, CO₂, and CH₄ after adding 9 t ha^?1 biochar on an agricultural soil in Southern Finland in May 2009. We conducted these measurements twice a week for 1.5 months, between sowing and canopy closure, to capture the period of highest N₂O emissions, where the potential for mitigation would also be highest. Biochar addition increased CH₄ uptake (96% increase in the average cumulative CH₄ uptake), but no statistically significant differences were observed in the CO₂ and N₂O emissions between the biochar amended and control plots. Added biochar increased soil water holding capacity by 11%. Further studies are needed to clarify whether this may help balance fluctuations in water availability to plants in the future climate with more frequent drought periods.