Characterization of ambient volatile organic compounds at a landfill site in Guangzhou,South China

Ambient air monitoring was conducted at Datianshan landfill, Guangzhou, South China in 1998 to investigate the seasonal and horizontal variations of trace volatile organic compounds (VOCs). Twelve sampling points over the Datianshan landfill were selected and samples were collected simultaneously using Carbontrap(TM) adsorption tubes. Thirty eight VOCs were detected in the winter, whereas 60 were detected in the summer. The VOC levels measured in summer were alkanes, 0.5-6.5 microg/m(3); aromatics, 2.3-1667 microg/m(3); chlorinated species, 0.2-31 microg/m(3); terpines, 0.1-34 microg/m(3); carbonyl species, 0.3-5.6 microg/m(3) and naphthalene and its derivatives, 0.4-27 microg/m(3). Compared to the summer samples the VOC levels in winter were much lower (mostly 1-2 orders of magnitude lower). The aromatics are dominant VOCs in landfill air both in winter and summer. High levels of alkylbenzene and terpines such as methyl-isopropylbenzene (max 1667 microg/m(3)) and limonene (max 162 microg/m(3)) cause undesirable odor. The similar correlation coefficients of BTEX in summer and winter suggest VOCs emissions were from landfill site sources. The variation of BTEX ratio at landfill site is different from that in the urban area of Guangzhou. It shows that the ambient VOCs at landfill site were different from the urban areas.     

Field monitoring of volatile organic compounds using passive air samplers in an industrial city in Japan

Highly portable, sensitive, and selective passive air samplers were used to investigate ambient volatile organic compound (VOC) levels at multiple sampling sites in an industrial city, Fuji, Japan. We determined the spatial distributions of 27 species of VOCs in three campaigns: Mar (cold season), May (warm season), and Nov (mild season) of 2004. In all campaigns, toluene (geometric mean concentration, 14.0microg/m3) was the most abundant VOC, followed by acetaldehyde (4.76microg/m3), and formaldehyde (2.58microg/m3). The spatial distributions for certain VOCs showed characteristic patterns: high concentrations of benzene and formaldehyde were typically found along major roads, whereas high concentrations of toluene and tetrachloroethylene (PCE) were usually found near factories. The spatial distribution of PCE observed was extremely consistent with the diffusion pattern calculated from Pollutant Release and Transfer Register data and meteorological data, indicated that passive air samplers are useful for determining the sources and distributions of ambient VOCs.     

Nonpoint sources of volatile organic compounds in urban areas-relative importance of land surfaces and air

Volatile organic compounds (VOCs) commonly detected in urban waters across the United States include gasoline-related compounds (e.g. toluene, xylene) and chlorinated compounds (e.g. chloroform, tetrachloroethane [PCE], trichloroethene [TCE]). Statistical analysis of observational data and results of modeling the partitioning of VOCs between air and water suggest that urban land surfaces are the primary nonpoint source of most VOCs. Urban air is a secondary nonpoint source, but could be an important source of the gasoline oxygenate methyl-tert butyl ether (MTBE). Surface waters in urban areas would most effectively be protected by controlling land-surface sources.     

Determination and Impact of Volatile Organics Emitted during Rush Hours in the Ambient Air around Gasoline Stations

Abstract

This study analyzes the volatile organic compounds (VOCs) in the ambient air around gasoline stations during rush hours and assesses their impact on human health. Results from this study clearly indicate that methyl tertiary butyl ether (MTBE), toluene, and isobutane are the major VOCs emitted from gasoline stations. Moreover, the concentrations of MTBE and toluene in the ambient air near gasoline stations are remarkably higher than those sampled on surrounding roads, revealing that these compounds are mainly released from gasoline stations. The concentration of VOCs near the gasoline stations without vapor recovery systems are ～7.3 times higher than those around the gasoline stations having the recovery systems. An impact on individual health and air quality because of gasoline station emissions was done using Integrated Risk Information System and Industrial Source Complex Short Term model.     

Multiple comparisons of organic,microbial, and fine particulate pollutants in typical indoor environments: Diurnal and seasonal variations

This study was performed to investigate the possible sources as well as seasonal and diurnal variations of indoor air pollutants in widely used four different environments (house, office, kindergarten, and primary school) in which people spend most of their time. Bioaerosol levels and species, volatile organic compound (VOC) levels, and PM_2.5 (particulate matter with an aerodynamic diameter ≤2.5 μm) levels were determined in different parts of these environments in parallel with outdoor sampling. Air pollution samplings were carried out in each microenvironment during five subsequent days in both winter and summer in Ankara, Turkey. The results indicated that bioaerosol, VOC, and PM_2.5 levels were higher in the winter than in the summer. Moreover, PM_2.5 and bioaerosol levels showed remarkable daily and diurnal variations, whereas a good correlation was found between the VOC levels measured in the morning and in the afternoon. Bacteria levels were, in general, higher than fungi levels. Among the VOCs, toluene was the most predominant, whereas elevated n-hexane levels were also observed in the kindergarten and the primary school, probably due to the frequent wet cleaning during school days. According to factor analysis, several factors were found to be significantly influencing the indoor air quality (IAQ), and amongst them, VOC-based products used indoors ranked first. The overall results indicate that grab sampling in naturally ventilated places may overestimate or underestimate the IAQ due to the inhomogeneous composition of indoor air caused by irregular exchanges with the outdoor air according to the season and/or occupants' habits.

Implications Seasonal and diurnal variations of VOCs, PM_2.5, bioaerosols in house, office, and schools were observed, in which PM_2.5 and bioaeorosols showed marked both intra- and interday variability, but VOCs did not. VOC-containing products were the most common source of air pollutants affecting the indoor air quality. External factors affecting the indoor air quality were season and indirectly ventilation. A grab sample cannot be representative in evaluating the air quality of a naturally ventilated environment precisely.     

First assessment of the PM<Subscript>10</Subscript> and PM<Subscript>2.5</Subscript> particulate level in the ambient air of belgrade city

INTENTION, GOAL, SCOPE, BACKGROUND: As the strong negative health effect of exposure to the inhalable particulate matter PM10 in the urban environment has been confirmed, the study of the mass concentrations, physico-chemical characteristics, sources, as well as spatial and temporal variation of atmospheric aerosol particles becomes very important. OBJECTIVE: This work is a pilot study to assess the concentration level of ambient suspended particulate matter, with an aerodynamic diameter of less than 10 microm, in the Belgrade central urban area. Average daily concentrations of PM10 and PM2.5 have been measured at three representative points in the city between June 2002 and December 2002. The influence of meteorological parameters on PM10 and PM2.5 concentrations was analyzed, and possible pollution sources were identified. METHODS: Suspended particles were collected on Pure Teflon filters by using a Mini-Vol low-volume air sampler (Airmetrics Co., Inc.; 5 l min(-1) flow rate). Particle mass was determined gravimetrically after 48 h of conditioning in a desiccator, in a Class 100 clean room at the temperature T = 20 degrees C and at about 50% constant relative humidity (RH). RESULTS AND DISCUSSION: Analysis of the PM10 data indicated a marked difference between season without heating--(summer; mean value 56 microg m(-3)) and heating season--(winter; mean value 96 microg m3); 62% of samples exceeded the level of 50 microg m(-3). The impact of meteorological factors on PM concentrations was not immediately apparent, but there was a significant negative correlation with the wind speed. CONCLUSIONS: The PM10 and PM2.5 mass concentrations in the Belgrade urban area had high average values (77 microg m(-3) and 61 microg m(-3)) in comparison with other European cities. The main sources of particulate matter were traffic emission, road dust resuspension, and individual heating emissions. When the air masses are coming from the SW direction, the contribution from the Obrenovac power plants is evident. During days of exceptionally severe pollution, in both summer and winter periods, high production of secondary aerosols occurred, as can be seen from an increase in PM2.5 in respect to PM10 mass concentration. RECOMMENDATION AND OUTLOOK: The results obtained gave us the first impression of the concentration level of particulate matter, with an aerodynamic diameter of less than 10 microm, in the Belgrade ambient air. Due to measured high PM mass concentrations, it is obvious that it would be very difficult to meet the EU standards (EEC 1999) by 2010. It is necessary to continue with PM10 and PM2.5 sampling; and after comprehensive analysis which includes the results of chemical and physical characterization of particles, we will be able to recommend effective control measures in order to improve air quality in Belgrade.     

Determination and impact of volatile organics emitted during rush hours in the ambient air around gasoline stations

This study analyzes the volatile organic compounds (VOCs) in the ambient air around gasoline stations during rush hours and assesses their impact on human health. Results from this study clearly indicate that methyl tertiary butyl ether (MTBE), toluene, and isobutane are the major VOCs emitted from gasoline stations. Moreover, the concentrations of MTBE and toluene in the ambient air near gasoline stations are remarkably higher than those sampled on surrounding roads, revealing that these compounds are mainly released from gasoline stations. The concentration of VOCs near the gasoline stations without vapor recovery systems are approximately 7.3 times higher than those around the gasoline stations having the recovery systems. An impact on individual health and air quality because of gasoline station emissions was done using Integrated Risk Information System and Industrial Source Complex Short Term model.     

Volatile organic compounds (VOCs) in urban atmosphere of Hong Kong

The assessment of volatile organic compounds (VOCs) has become a major issue of air quality network monitoring in Hong Kong. This study is aimed to identify, quantify and characterize volatile organic compounds (VOCs) in different urban areas in Hong Kong. The spatial distribution, temporal variation as well as correlations of VOCs at five roadside sampling sites were discussed. Twelve VOCs were routinely detected in urban areas (Mong Kok, Kwai Chung, Yuen Long and Causeway Bay). The concentrations of VOCs ranged from undetectable to 1396 microg/m3. Among all of the VOC species, toluene has the highest concentration. Benzene, toluene, ethylbenzene and xylenes (BTEX) were the major constituents (more than 60% in composition of total VOC detected), mainly contributed from mobile sources. Similar to other Asian cities, the VOC levels measured in urban areas in Hong Kong were affected both by automobile exhaust and industrial emissions. High toluene to benzene ratios (average T/B ratio = 5) was also found in Hong Kong as in other Asian cities. In general, VOC concentrations in the winter were higher than those measured in the summer (winter to summer ratio > 1). As toluene and benzene were the major pollutants from vehicle exhausts, there is a necessity to tighten automobile emission standards in Hong Kong.     

Comparison of seasonal phenol and p-cresol emissions from ground-level area sources in a dairy operation in central Texas

Although there are more than 200 odor-causing volatile organic compounds (VOCs), phenol and p-cresol are two prominent odor-causing VOCs found downwind from concentrated animal feeding operations (CAFOs). The VOC emissions from cattle and dairy production are difficult to quantify accurately because of their low concentrations, spatial variability, and limitations of available instruments. To quantify VOCs, a protocol following US. Environmental Protection Agency (EPA) Method TO-14A has been established based on the isolation flux chamber method and a portable gas chromatograph (GC) coupled with a purge-and-trap system. The general objective of this research was to quantify phenol and p-cresol emission rates (ERs) from different ground-level area sources (GLASs) in a free-stall dairy during summer and winter seasons using this protocol. Two-week-long sampling campaigns were conducted in a dairy operation in central Texas. Twenty-nine air samples were collected during winter and 37 samples were collected during summer from six specifically delineated GLASs (barn, loafing pen, lagoon, settling basin, silage pile, and walkway) at the free-stall dairy. Thirteen VOCs were identified during the sampling period and the GC was calibrated for phenol and p-cresol, the primary odorous VOCs identified. The overall calculated ERs for phenol and p-cresol were 2656 +/- 728 and 763 +/- 212 mg hd(-1) day(-1), respectively, during winter. Overall phenol and p-cresol ERs were calculated to be 1183 +/- 361 and 551 +/- 214 mg hd(-1) day(-1), respectively, during summer. In general, overall phenol and p-cresol ERs during winter were about 2.3 and 1.4 times, respectively, higher than those during summer.     

MTBE in California's Drinking Water: A Comparison of Groundwater Versus Surface Water Sources

During the last decade, the fuel oxygenate methyl tertiary butyl ether (MTBE) has received widespread attention as a potential threat to water quality, primarily due to leaking underground gasoline storage tanks and watercraft with two-stroke engines. In this article, we examine the annual detection frequency, number of new source detections, and concentration of MTBE detected in California's public drinking water groundwater and surface water sources from 1995 to 2002. This work builds on our previous evaluations of California's water quality monitoring database. However, it is unique in that it includes separate evaluations for groundwater and surface water sources that are of greatest concern to regulators, and which are likely being used for current public consumption. Our evaluations also include full-year data for 2002 (which have not been published previously) and an analysis of how the sampling and reported detections of MTBE vary by geographic location. We find that MTBE was generally detected (at any level) in approximately 0.5-0.9% and 0.2-0.4% of all groundwater sources assuming a one-detection and two-detection criterion, respectively. The overall detection frequency for MTBE in surface water sources is significantly higher than for groundwater sources, although these surface water detections appear to have substantially declined since 1996 (e.g., 7-9% for all surface water sources during 1996 to 1999 and 4% for all surface water sources during 2000 to 2002, assuming a one-detection criterion). The detection frequency of MTBE concentrations at or above the state drinking water standards in all drinking water sources (both groundwater and surface water sources) and the subset of drinking water sources that are likely to currently be delivered to consumers is markedly lower (and often zero). Despite the significant increase in water sampling over time, the number of new drinking water sources found to contain MTBE in California has not increased at the same rate and appears to have remained relatively stable or to have decreased since 1998. The data also show that nearly all of the 58 counties in California have routinely sampled at least some of their groundwater and surface water sources for MTBE over the last 8 years. Geographical evaluations show that MTBE has been detected (at least once) in groundwater sources in 34 counties and in surface water sources in 18 counties but has only been detected routinely (i.e., for 3 or more years) in 16 and 7 counties, respectively. Detected concentrations of MTBE are also generally below state drinking water standards, particularly for surface water sources. In short: (1) MTBE is rarely found in California groundwater or surface water sources that are of greatest concern to regulators or the public, and (2) drinking water detections of MTBE are expected to decline in the future due to the pending phase-out of MTBE and recent regulatory programs aimed at controlling gasoline releases from underground storage tanks and two-stroke-engine watercraft.     

Emission and Fate Assessment of Methyl Tertiary Butyl Ether in the Boston Area Airshed Using a Simple Multimedia Box Model: Comparison with Urban Air Measurements

Abstract

Expected urban air concentrations of the gasoline additive methyl tertiary butyl ether (MTBE) were calculated using volatile emissions estimates and screening transport models, and these predictions were compared with Boston, MA, area urban air measurements. The total volatile flux of MTBE into the Boston primary metropolitan statistical area (PMSA) airshed was calculated based on estimated automobile nontailpipe emissions and the Universal Quasi-Chemical Functional-Group Activity Coefficient computed abundance of MTBE in gasoline vapor. The fate of MTBE in the Boston PMSA was assessed using both the European Union System for the Evaluation of Substances, which is a steady-state multimedia box model, and a simple airshed box model. Both models were parameterized based on the meteorological conditions observed during air sampling in the Boston area. Measured average urban air concentrations of 0.1 and 1 [H9262]g/m³ MTBE during February and September of 2000, respectively, were comparable to corresponding model predictions of 0.3 and 1 μg/m³ and could be essentially explained from estimated temperature-dependent volatile emissions rates, observed average wind speed (the airshed flushing rate), and reaction with ambient tropospheric hydroxyl radical (.OH), within model uncertainty. These findings support the proposition that one can estimate gasoline component source fluxes and use simple multimedia models to screen the potential impact of future proposed gasoline additives on urban airsheds.     

A study of the atmospheric VOCs of Mount Tai in June 2006

Intensive field investigations were conducted at the summit of Mount Tai in June 2006 to understand the effects of the local and regional sources on atmospheric volatile organic compounds (VOCs) distributions. A total of 60 samples were collected and determined by quantitative analytical methods. The concentrations of the total VOCs (TVOCs) observed in the air of Mount Tai were 6.95 ± 5.71 ppb. Aromatic hydrocarbons provided the largest contribution to TVOCs, followed by alkanes and halocarbons. High levels of halocarbons accounted for 20% of TVOCs due to emission from a PVC plant located at the foot of Mount Tai. Alkenes and cycloalkanes contributed little to the total VOCs. The day-and-night differences and day-to-day variations in the concentrations of four selected species were investigated and the effects of several factors such as meteorological parameters, sources and transport characteristics on them were discussed in details. A back trajectory analysis showed that relatively higher levels of VOCs were related to long-range transport of pollutants from polluted areas. The vertical motions of air masses also had a large impact on the variations of the levels of VOCs. The result of the variability–lifetime relationships of VOCs, which is used to estimate the remoteness of the sampling location, showed that Mount Tai represents intermediate conditions between remote sites and sites in the vicinity of sources.     

Emission and fate assessment of methyl tertiary butyl ether in the Boston area airshed using a simple multimedia box model: comparison with urban air measurements

Expected urban air concentrations of the gasoline additive methyl tertiary butyl ether (MTBE) were calculated using volatile emissions estimates and screening transport models, and these predictions were compared with Boston, MA, area urban air measurements. The total volatile flux of MTBE into the Boston primary metropolitan statistical area (PMSA) airshed was calculated based on estimated automobile nontailpipe emissions and the Universal Quasi-Chemical Functional-Group Activity Coefficient computed abundance of MTBE in gasoline vapor. The fate of MTBE in the Boston PMSA was assessed using both the European Union System for the Evaluation of Substances, which is a steady-state multimedia box model, and a simple airshed box model. Both models were parameterized based on the meteorological conditions observed during air sampling in the Boston area. Measured average urban air concentrations of 0.1 and 1 microg/m3 MTBE during February and September of 2000, respectively, were comparable to corresponding model predictions of 0.3 and 1 microg/m3 and could be essentially explained from estimated temperature-dependent volatile emissions rates, observed average wind speed (the airshed flushing rate), and reaction with ambient tropospheric hydroxyl radical (*OH), within model uncertainty. These findings support the proposition that one can estimate gasoline component source fluxes and use simple multimedia models to screen the potential impact of future proposed gasoline additives on urban airsheds.     

Evaluation of the Use of Diffusive Air Samplers for Determining Temporal and Spatial Variation of Volatile Organic Compounds in the Ambient Air of Urban Communities

Abstract

The Houston-Galveston metropolitan area has a relatively high density of point and mobile sources of air toxics, and determining and understanding the relationship between emissions and ambient air concentrations of air toxics is important for evaluating potential impacts on public health and formulating effective regulatory policies to control this impact, both in this region and elsewhere. However, conventional ambient air monitoring approaches are limited with regard to expense, siting limitations, and representative sampling necessary for adequate exposure assessment. The overall goal of this multiphase study is to evaluate the use of simple passive air samplers to determine temporal and spatial variability of the ambient air concentrations of selected volatile organic compounds (VOCs) in urban areas. Phase 1 of this study, reported here, was a field evaluation of 3M organic vapor monitors (OVMs) involving limited comparisons with commonly used active sampling methods, an assessment of sampler precision, a determination of optimal sampling duration, and an investigation of the utility of a simple modification of the commercial sampler. The results indicated that a sampling duration of 72 hr exhibited generally low bias relative to automated continuous gas chromatography measurements, good overall precision, and an acceptable number of measurements above detection limits. The modified sampler showed good correlation with the commercial sampler, with higher sampling rates, although lower than expected.     

Methyl tert-butyl ether (MTBE) in urban and rural precipitation in Germany

The use of the oxygenate methyl tert-butyl ether (MTBE) in gasoline has led to detectable concentrations in urban and rural air up to 160 ppbV. Results from MTBE measurement in precipitation have not been reported so far. In the present study, 120 samples of precipitation collected at 17 sampling locations all over Germany have been analyzed for their MTBE content. Analysis is performed by a combination of headspace-solid-phase microextraction (HS-SPME) and gas chromatography/mass spectrometry (GC-MS). A 75 μm poly(dimethylsiloxane)/Carboxene fiber and a cryostat is used for SPME. The detection limit is 10 ng/l. In precipitation samples, MTBE was detected in wintertimes only with a maximum concentration of 85 ng/l. Measurement at Frankfurt/M City from 6 September 2000 to 12 March 2001 provided for 49% of the data concentrations in the range of 30–85 ng/l (n=17). Sampling in winter 2000/2001 at several German cities and rural locations showed that MTBE is more often detectable in urban (86%, n=78) than in rural (18%, n=42) precipitation. By comparing the results with corresponding temperatures and amounts of precipitation it can be concluded that the detection of MTBE in urban precipitation is observed at ambient temperatures lower than about 10–15°C. Moreover, the first precipitation after a dry period accumulates more MTBE than precipitation during or at the end of a wet period (wash-out effect). Highest concentrations occurred in snow samples. Corresponding mean air equilibrium concentrations of 0.04 ppbV (urban samples) and 0.01 ppbV (rural samples) are calculated. This is about one magnitude lower than year round and summertime measurements in the US and in Switzerland. Urban runoff (n=12) and corresponding precipitation sampling indicate that urban runoff might be composed of about 20% MTBE that is already transported by air and precipitation, whereas about 80% may be attributed to direct uptake of vehicle emissions and leakage near the road during precipitation.     

Influences of metals on kinetics of methyl tert-butyl ether biodegradation by Ochrobactrum cytisi

The influence of zinc, manganese, and nickel on the degradation of MTBE (methyl tert-butyl ether), by an aerobic MTBE-degrading strain, Ochrobactrum cytisi, were investigated. The result showed that unlike previous findings, O. cytisi was able to degrade MTBE through direct metabolism when MTBE was present as the only carbon source. The degradation rate of MTBE was rapid, completed within 80 h. MTBE biodegradation by this strain was stimulated at low concentrations of Zn(2+) (1-5 mg l(-1)) and Mn(2+) (1-5 mg l(-1)) but inhibited at high concentrations of Zn(2+) (20 mg l(-1)) and Mn(2+) (20 mg l(-1)), and at low concentration of Ni(2+) (1-4 mg l(-1)). Kinetic parameters for MTBE degradation in the presence or absence of metals were obtained through nonlinear regression and a least-square minimization procedure. In all cases, a good agreement was achieved between kinetic simulations and experimental results.     

Exposure to methyl tertiary butyl ether and benzene in close proximity to service stations

Exposure estimates based solely on proximity to air pollution sources are not sound and require confirmation. Accordingly, since a very limited amount of actual data for this type of exposure estimate is currently available, this study was conducted to provide actual data on residents' exposure to two important gasoline constituents [methyl tertiary butyl ether (MTBE) and benzene] relative to their proximity to roadside service stations. The results confirmed that residents in neighborhoods near service stations are exposed to elevated ambient MTBE and benzene levels compared with those living farther from such a source. However, it was also found that the presumed elevated outdoor benzene levels (a mean of 1.7 ppb) even in close proximity to service stations did not exceed the indoor levels (a mean of 2.2 ppb) of exposure for those living nearby. Regardless of residents' distance from service stations, an indoor source (cigarette smoking) appeared to be the major contributor to their benzene exposure. Conversely, for MTBE, roadside service stations were found to be the major contributor to residents' exposure. In addition, the residents close to the stations were exposed to elevated indoor and outdoor MTBE levels. The sampling period (daytime and nighttime) and season (winter and summer) were additional parameters for the outdoor MTBE and benzene levels and the indoor MTBE levels. Meanwhile, the breathing zone air concentrations of service station attendants for both MTBE and benzene were significantly higher than those of drivers (p < 0.05). In addition, the breathing zone concentrations were significantly higher during summer than during winter for both drivers and attendants (p < 0.05).     

Aerostat-lofted instrument and sampling method for determination of emissions from open area sources

An aerostat-borne instrument and sampling method was developed to characterize air samples from area sources, such as emissions from open burning. The 10 kg battery-powered instrument system, termed “the Flyer”, is lofted with a helium-filled aerostat of 4 m nominal diameter and maneuvered by means of one or two tethers. The Flyer can be configured variously for continuous CO₂ monitoring, batch sampling of semi-volatile organic compounds (SVOCs), volatile organic compounds (VOCs), black carbon, metals, and PM by size. The samplers are controlled by a trigger circuit to avoid unnecessary dilution from background sampling when not within the source plume. The aerostat/Flyer method was demonstrated by sampling emissions from open burning (OB) and open detonation (OD) of military ordnance. A carbon balance approach was used to derive emission factors that showed excellent agreement with published values.     

Particle size distributions and elemental composition of atmospheric particulate matter in southern Italy

Three 2-wk seasonal field campaigns were performed in 2003 and 2004 at a sampling site on the southern Tyrrhenian coast of Italy with the aim to investigate the dynamics and characteristics of particle-bound pollutants in the Mediterranean area. Fine (PM(2.5)) and coarse particulate matter (PM(10-2.5)) size fractions were collected by a manual dichotomous sampler on 37-mm Teflon filters over a 24-hr sampling period. On average, 70% of the total PM(10) (PM(2.5) + PM(10-2.5)) mass was associated with the coarse fraction and 30% with the fine fraction during the three campaigns. The ambient concentrations of Pb, Ni, Cr, Zn, Mn, V, Cd, Fe, Cu, Ca, and Mg associated with both size fractions were determined by atomic absorption spectrometry. Ambient concentrations showed differences in their absolute value, ranging from few ng x m(-3) to microg x m(-3), as well as in their variability within the PM(2.5) and PM(10-2.5) size fractions. PM(10) levels were well below the European Union (EU) limit value during the study period with the exception of three events during the first campaign (fall) and five events during the third campaign (spring). Two main sources were identified as the major contributors including mineral dust, transported from North Africa, and sea spray from the Tyrrhenian Sea. Comparing the results with backward trajectories, calculated using the Hybrid Single-Particle Lagrangian Integrated Trajectory Model (HYSPLIT) and Total Ozone Mapping Spectrometer-National Aeronautics and Space Administration (TOMS-NASA) maps, it was observed that in central and eastern Europe, the Tyrrhenian Sea and North Africa were the major emission source regions that affected the temporal variations and daily averages of PM(2.5) and PM(10-2.5) concentrations.     

Characterizing and locating air pollution sources in a complex industrial district using optical remote sensing technology and multivariate statistical modeling

Emissions of volatile organic compounds (VOCs) are most frequent environmental nuisance complaints in urban areas, especially where industrial districts are nearby. Unfortunately, identifying the responsible emission sources of VOCs is essentially a difficult task. In this study, we proposed a dynamic approach to gradually confine the location of potential VOC emission sources in an industrial complex, by combining multi-path open-path Fourier transform infrared spectrometry (OP-FTIR) measurement and the statistical method of principal component analysis (PCA). Close-cell FTIR was further used to verify the VOC emission source by measuring emitted VOCs from selected exhaust stacks at factories in the confined areas. Multiple open-path monitoring lines were deployed during a 3-month monitoring campaign in a complex industrial district. The emission patterns were identified and locations of emissions were confined by the wind data collected simultaneously. N,N-Dimethyl formamide (DMF), 2-butanone, toluene, and ethyl acetate with mean concentrations of 80.0?±?1.8, 34.5?±?0.8, 103.7?±?2.8, and 26.6?±?0.7 ppbv, respectively, were identified as the major VOC mixture at all times of the day around the receptor site. As the toxic air pollutant, the concentrations of DMF in air samples were found exceeding the ambient standard despite the path-average effect of OP-FTIR upon concentration levels. The PCA data identified three major emission sources, including PU coating, chemical packaging, and lithographic printing industries. Applying instrumental measurement and statistical modeling, this study has established a systematic approach for locating emission sources. Statistical modeling (PCA) plays an important role in reducing dimensionality of a large measured dataset and identifying underlying emission sources. Instrumental measurement, however, helps verify the outcomes of the statistical modeling. The field study has demonstrated the feasibility of using multi-path OP-FTIR measurement. The wind data incorporating with the statistical modeling (PCA) may successfully identify the major emission source in a complex industrial district.