Adsorption of pesticides on resins

The objective of this work was to assess the capability of organic hydrophobic polymeric resins Amberlite XAD-4 and XAD-7 to remove the pesticides alachlor and amitrole from water. The pesticides adsorption on the two different adsorbents was measured by batch equilibrium technique and isotherm types and parameters were estimated. Two theoretical models were applied based on a Freundlich and a Langmuir isotherms. The effect of pesticides chemical composition and structure as well as the nature of solid surface on the efficiency of adsorption was evaluated. The influence of pH also was studied. In low pH solutions adsorption of amitrole was higher upon the nonionic aliphatic acrylic ester copolymer XAD-7 in comparison to the nonionic, crosslinked macroreticular copolymer of styrene divinylbenzene XAD-4. In neutral and intermediate pH solutions the polar acrylic ester copolymer XAD-7 was more effective to the retention of alachlor. The acrylic ester copolymer showed at pH 3 the lower effectiveness in alachlor removal from water. The data of the adsorption isotherms of pesticides upon the examined polymeric resins seemed to conform to both the Freundlich and the Langmuir isotherm models.     

ZH-02树脂对水中腐殖酸的吸附去除研究

通过几种吸附树脂ZH 0 0、ZH 0 1、ZH 0 2、ZH 0 3、颗粒活性炭 (GAC)和AmberliteXAD 4对腐殖酸的静态吸附试验的筛选结果 ,发现大孔树脂ZH 0 2对腐殖酸具有较好的吸附效果。利用颗粒活性炭作为参照 ,探讨了ZH 0 2的动态吸附去除效果和脱附再生条件 ,发现常温下醇碱溶液效果较好。     

大孔树脂吸附去除水中的2,4,6-三硝基甲苯

研究了2种大孔树脂XAD-4和NDA-804对水中的TNT的吸附行为。2种树脂对TNT的吸附等温线表明,温度的升高有利于吸附,在35℃条件下XAD-4树脂与NDA-804树脂对TNT的最高平衡吸附量分别达82.86 mg/g和94.26mg/g。采用Langmuir方程和Freundlich方程用于吸附等温线的解释,结果表明,吸附等温线更加符合Langmuir模型,相关系数均大于0.99。TNT在2种树脂上的吸附符合准二级动力学方程,TNT初始浓度越低,达到吸附平衡所需时间越短,在1 h内可达到吸附平衡。采用NDA-804处理对TNT废水,废水中TNT浓度由103.58 mg/L降至0.4 mg/L,去除率达99.6%,吸附后的树脂采用pH=2的乙醇和盐酸的混合液脱附可再生,高浓度再生溶液经蒸馏可回收TNT,实现了废水治理与资源化。     

Adsorption of phenolic compounds from aqueous solutions by a water-compatible hypercrosslinked polymeric adsorbent

A water-compatible hypercrosslinked polymeric adsorbent (NJ-8) for adsorbing and removing phenolic compounds from their aqueous solutions was prepared. This product can be used directly without a wetting process. Its adsorption property toward four phenolic compounds, phenol, p-cresol, p-chlorophenol, and p-nitrophenol was tested using the commercial Amberlite XAD-4 as a reference. The capacities of equilibrium adsorption for all four phenolic compounds on the NJ-8 from their aqueous solutions are around two times as high as that of Amberlite XAD4 within the temperature range 283-323 K, which may contribute to their micropore structure and the partial polarity on the network. Freundlich isotherm equations, as well as relative adsorption capacities and isosteric adsorption enthalpies for the four phenolic compounds, indicate that the adsorption of phenolic compounds on the NJ-8 resin is a physical adsorption process. Mini-column adsorption studies for phenol on Amberlite XAD4 and NJ-8 resins show that the breakthrough adsorption capacities are 0.54 and 0.99 mmol/ml, and the total capacities are 0.62 and 1.37 mmol/ml, while no extra acetone was needed to remove the adsorbed phenol from NJ-8 as from Amberlite XAD4.     

Adsorption Characteristics of Activated Carbon and XAD4 Resin for the Removal of Hazardous Organic Solvents

A comparative study has been conducted on adsorption/desorption of six hazardous organic vapors on synthetic resin (XAD4) and activated carbon, using a differential reactor involving the expansion of a quartz spring. While both sorbents can effectively remove the organic vapors, it was observed that at low concentrations activated carbon adsorbed more organic vapor than synthetic resin. At higher, industrial concentrations, the resins adsorbed more vapor as demonstrated by the slopes of the equilibrium isotherms. The resin also showed much higher desorptlon.

The effective Intraparticle diffusion coefficients (D_e) were observed to be strongly dependent on solute concentration. Pore diffusion dominated the adsorption/desorption of the six organic vapors on XAD4 resin. For the carbon system, pore diffusion dominated the adsorption but surface diffusion contributed to the desorptlon process. This is believed to be due to higher Interaction of the adsorbates with activated carbon.     

Equilibrium and kinetic studies on the adsorption of aniline compounds from aqueous phase onto bifunctional polymeric adsorbent with sulfonic groups

In the present study, a hydrophilic bifunctional polymeric resin (LS-2) with sulfonic groups was synthesized, and the adsorption performance of three aniline compounds, aniline, 4-methylaniline, and 4-nitroaniline onto LS-2 was compared with that on the commercial Amberlite XAD-4. The uptake of the aniline compounds on LS-2 is a procedure of coexistence of physisorption and chemisorption and obeys the pseudo-second order rate equation, while the uptake of the compounds on XAD-4 is merely a physical adsorption and follows the pseudo-first order rate equation. All the isothermal data fit well with the Freundlich model, and the values of K(F) of the compounds adsorbing on LS-2 are much higher than those on XAD-4 suggesting the higher adsorbing capacities on LS-2 than those on XAD-4, which may be attributed to the microporous structure and the polar groups on the network of LS-2 resin. Dynamic adsorption and desorption studies for aniline on LS-2 show that the breakthrough adsorption capacity and the total adsorption capacity are 0.96 and 1.24 mmol per milliliter resin, respectively. Nearly 100% regeneration efficiency for the adsorbent was achieved by 5% hydrochloric acid.     

Evaluation of the reaction artifacts in an annular denuder-based sampler resulting from the heterogeneous ozonolysis of naphthalene

The heterogeneous ozonolysis of naphthalene adsorbed on XAD-4 resin was studied using an annular denuder technique. The experiments involved depositing a known quantity of naphthalene on the XAD-4 resin and then measuring the quantity of the solid naphthalene that reacted away under a constant flow of gaseous ozone (0.064 to 4.9 ppm) for a defined amount of time. All experiments were performed at room temperature (26 to 30 °C) and atmospheric pressure. The kinetic rate coefficient for the ozonolysis reaction of naphthalene adsorbed on XAD-4 resin is reported to be (10.1?±?0.4)?×?10^?19 cm³ molecule^?1 s^?1 (error is 2σ, precision only). This value is five times greater than the currently recommended literature value for the homogeneous gas phase reaction of naphthalene with ozone. The obtained rate coefficient is used to evaluate reaction artifacts from field concentration measurements of naphthalene, acenaphthene, and phenanthrene. The observed uncertainties associated with field concentration measurements of naphthalene, acenaphthene, and phenanthrene are reported to be much higher than the uncertainties associated with the artifact reactions. Consequently, ozone reaction artifact appears to be negligible compared to the observed field measurement uncertainty results.     

The use of XAD-resins for the detection of mutagenic activity in water: I. Studies with surface water

A study of the effects of different XAD-resins, bed volume, flow rate, pH and type of eluent on the extraction of organic mutagens from surface water is presented. XAD-4/8 is as effective as XAD-2 in concentrating organic mutagens from surface water and dimethylsulfoxide (DMSO) is as efficient as acetone in eluting the adsorbed organic mutagens. The latter allows direct testing up to 0.5 ml of DMSO concentrate in the Ames test. Variation of the pH of the water after passing the XAD-4/8, followed by readsorption, shows that the majority of the mutagenic activity due to dissolved organics is adsorbed at neutral pH. Only a minor fraction is readsorbed at pH 3. Further a XAD-4/8 concentrate and a similar concentrate prepared by freeze drying gives similar mutagenic activity. This indicates that many of the organic mutagens are recovered in the XAD-4/8 concentrate.It is concluded that adsorption on XAD-4/8, followed by direct testing of the DMSO eluates in the Ames test, presents a rapid and relatively simple way to detect low concentrations of organic mutagens in surface water. The general suitability of the method is shown for different types of surface water.     

Mg/Al水滑石对水中痕量邻苯二甲酸酯的吸附动力学和热力学

研究了Mg／A1水滑石对水中痕量邻苯二甲酸二甲酯（DMP）、邻苯二甲酸二（2一乙基己基）酯（DEHP）和邻苯二甲酸二辛酯（DnOP）的吸附动力学和热力学特性。结果表明，在所研究的浓度范围内，3种邻苯二甲酸酯的吸附动力学曲线均符合准二级速率方程，DMP、DEHP和DnOP分别在600、200和200min基本达到吸附平衡；3种邻苯二甲酸酯的吸附等温线基本符合Langmuir和Freundlich吸附等温方程；在283～308K范围，pH=6．36，3种邻苯二甲酸酯初始浓度均为50μg／L时，吸附过程△H为负值且绝对值为5～12kJ／mol，表明吸附为放热过程，以表面物理吸附为主，邻苯二甲酸酯在Mg／Al水滑石上的吸附是色散力、诱导力、取向力和氢键力等多种作用力协同作用的结果。     

Sampling and Analysis of Volatile Organic Compounds Evolved During Thermal Processing of Acrylonitrile Butadiene Styrene Composite Resins

Abstract

The evaluation of emissions of volatile organic compounds (VOCs) during processing of resins is of interest to resin manufacturers and resin processors. An accurate estimate of the VOCs emitted from resin processing has been difficult due to the wide variation in processing facilities. This study was designed to estimate the emissions in terms of mass of emitted VOC per mass of resin processed.

A collection and analysis method was developed and validated for the determination of VOCs present in the emissions of thermally processed acrylonitrile butadiene styrene (ABS) resins. Four composite resins were blended from automotive, general molding, pipe, and refrigeration grade ABS resins obtained from the manufacturers. Emission samples were collected in evacuated 6-L Summa canisters and then analyzed using gas chromatography/flame ionization detection/mass selective detection (GC/FID/MSD). Levels were determined for nine target analytes detected in canister samples, and for total VOCs detected by an inline GC/FID. The emissions evolved from the extrusion of each composite resin were expressed in terms of mass of VOCs per mass of processed resin. Styrene was the principal volatile emission from all the composite resins. VOCs analyzed from the pipe resin sample contained the highest level of styrene at 402 μg/g. An additional collection and detection method was used to determine the presence of aerosols in the emissions. This method involved collecting particulates on glass fiber filters, extracting them with solvents, and analyzing them using gas chromatography/mass spectrometry (GC/MS). No significant levels of any of the target analytes were detected on the filters.     

树脂吸附法处理硫化促进剂CA生产废水的研究

采用特种吸附树脂处理促进剂CA生产废水 ,系统地研究了废水的pH值、吸附温度及吸附流量等因素对树脂吸附性能的影响 ,以及以稀硫酸为脱附剂 ,其配比、流量、温度等对树脂脱附性能的影响。实验结果表明 ,特种吸附树脂对该废水具有良好的吸附 脱附效果 ,废水经吸附处理后 ,CODCr浓度由 2 0 0 0 0mg/L左右降至 30 0mg/L以下 ,CODCr去除率达98%以上。该工艺简单 ,运行稳定 ,操作简便 ,可望实现工业化。     

Quaternary adsorption equilibria from aqueous systems onto decolourizing activated carbon

An experimental study has been conducted to obtain the adsorption isotherms of four typical pollutants from quaternary aqueous systems onto decolourizing activated carbon. The four materials investigated are: Phenol, 1,4-dihydroxybenzene, 4-amino-l-naphthalene sulfonic acid-sodium salt and Benzoic acid. The study has concentrated on the dilute region of concentrations which range from 10 to 165 ppm (mg/L) at an operating temperature of 30 °C.

The quaternary adsorption equilibria have been modeled using the extended Langmuir predictive model and the ideal adsorbed solution (IAS) theory. In employing these models for the prediction of multicomponent adsorption equilibria, the single-solute isotherms are needed. These isotherms have been fitted to Langmuir, Freundlich, and Dubinin models and the resulting model parameters, which are needed for the prediction of multicomponent adsorption equilibria, are reported. Predictions obtained from the extended Langmuir predictive model and the ideal adsorbed solution (IAS) model are in agreement, however, they deviate to an appreciable extent from experimental observations.     

新型TCAS吸附树脂对水中Cd^2＋的吸附去除研究

通过静态吸附试验，研究一种由超分子受体化合物磺化硫杂杯芳烃（TCAS）与树脂结合的产物——新型TCAS吸附树脂对重金属Cd^2＋的吸附去除性能，并初步探讨了吸附机理。试验研究结果表明，TCAS吸附树脂对Cd^2＋的饱和吸附量为14．45mg/g。当温度为20℃，0．5gTCAS吸附树脂对10mL浓度为5113g／L的Cd^2＋溶液吸附60min时，Cd^2＋的去除率可达到99％以上。pH值是影响TCAS吸附树脂吸附效果的重要因素，在pH=5—9时，Cd^2＋的去除率随着pH值的升高而增大。在试验范围内，TCAS吸附树脂对Cd^2＋吸附符合Freundlich方程。吸附在TCAS吸附树脂上的Cd^2＋可洗脱回收，TCAS吸附树脂也可再生利用。TCAS吸附树脂对重金属Cd^2＋的吸附机理主要归因于TCAS对Cd^2＋的络合作用。     

弱碱性树脂吸附-解吸苦味酸

考察了水中苦味酸在弱碱性离子交换树脂D301R上的吸附与解吸。研究了吸附热力学、动力学特性及吸附机理。结果表明,树脂在pH=2.7～10.2时,吸附能力最好。等温平衡吸附遵循Freundlich模型。吸附过程为吸热、熵增的自发过程。吸附动力学符合Lagergren准二级速率方程,颗粒内扩散为吸附速率的主要控制步骤,吸附速率常数为7.23×10-5～1.20×10-4g/(mg.min),吸附活化能为19.4 kJ/mol。树脂上吸附的苦味酸可用HNO3+丙酮混合液定量洗脱,洗脱率达99%。静态吸附和脱附的比较结果证实了吸附过程中存在不可逆化学吸附。树脂对苦味酸的吸附主要是通过静电吸附、酸碱络合吸附、氢键吸附等协同作用来完成的。     

Natural organic matter (NOM) in roof runoff and its impact on the Fe0 treatment system of dissolved metals

The present work investigates the impacts and mechanisms associated with natural organic matter (NOM) in the Fe0 treatment system of Cu2+ and Zn2+ under roof runoff conditions. The NOM in runoff waters was characterized using XAD-4/8 adsorption resins, copper complexation, acidic capacity and liquid chromatography with online carbon detection. Batch kinetic experiments and flow-through configurations were performed and the results of metal removal were elucidated taking into account the characteristics of NOM. Based on the findings, it is shown that NOM influences the removal of metals through several complex pathways. At an un-favored condition for adsorption of metals, i.e., on iron corrosion products, at pH相似文献   

Sorption of the herbicides diquat and difenzoquat from aqueous medium by polymeric resins in the presence of sodium dodecylsulfate: Kinetic and mechanistic study

The goal of this work was to propose a novel method for the solid-phase extraction of the herbicides diquat (DQT²⁺) and difenzoquat (DFQT⁺) from aqueous medium using polymeric Amberlite XAD-2 and XAD-4 resins in the presence of sodium dodecylsulfate (SDS). The addition of SDS to the medium was of fundamental importance in order to allow the formation of a negatively charged surface able to sorb the cationic solutes. Several factors that could influence the sorption process, such as SDS concentration in the medium, sorbent mass, pH, ionic strength, and initial concentration of the solutes were investigated. Kinetic studies were also performed to model the system and to identify the mechanisms that operate the sorption process of the herbicides. SDS concentration in the medium presented remarkable influence on the extraction efficiency, achieving maximum values when the ratios [SDS]/[herbicide] were approximately 90, for XAD-2, and 22 and 11 for DQT²⁺ and DFQT⁺, respectively, for XAD-4. The sorption process followed a pseudo second-order kinetic in all cases studied. It was also found that an intraparticle diffusion process controlled exclusively the sorption of the herbicides by the Amberlite XAD-2 and XAD-4 resins in the first 15 min, becoming less active with time.     

木粉/壳聚糖接枝丙烯酸-丙烯酰胺吸附树脂对二元重金属离子溶液中Pb^2＋的吸附

采用自制木粉/壳聚糖接枝丙烯酸-丙烯酰胺吸附树脂R1、R2、R3对二元金属离子Cu2＋/Pb2＋和Zn2＋/Pb2＋溶液中的吸附性能进行了较系统考察。Pb2＋离子溶液中存在竞争离子Cu2＋、Zn2＋时,随竞争离子浓度增加,3种吸附树脂R1、R2、R3对Pb2＋的吸附量明显下降,而竞争离子吸附量显著增加。二元溶液中各金属离子浓度相同时,3种树脂对竞争离子Cu2＋、Zn2＋的吸附量大于对Pb2＋的吸附量;各溶液中分别加入NaCl及NaNO3、尿素后,对Pb2＋离子的吸附量下降迅速。随吸附树脂用量增加,竞争离子Cu2＋、Zn2＋的吸附量逐渐减小,Pb2＋的吸附量在吸附树脂用量0.10 g/L（Zn2＋/Pb2＋溶液）或0.15 g/L（Cu2＋/Pb2＋溶液）时出现最大值。溶液pH值对树脂吸附性能有显著影响。3.0     

Adsorption and removal of As(V) and As(III) using Zr-loaded lysine diacetic acid chelating resin

An adsorption process for the removal of As(V) and As(III) was evaluated under various conditions using zirconium(IV) loaded chelating resin (Zr-LDA) with lysine-Nalpha,Nalpha diacetic acid functional groups. Arsenate ions strongly adsorbed in the pH range from 2 to 5, while arsenite was adsorbed between pH 7 and 10.5. The sorption mechanism is an additional complexation between arsenate or arsenite and Zr complex of LDA. Adsorption isotherm data could be well interpreted by Langmuir equation for As(V) at pH 4 and As(III) at pH 9 with a binding constant 227.93 and 270.47 dm3 mol(-1) and capacity constant 0.656 and 1.1843 mmol g(-1), respectively. Regeneration of the resin was carried out for As(V) using 1 M NaOH. Six adsorption/desorption cycles were performed without significant decrease in the uptake performance. Column adsorption studies showed that the adsorption of As(V) is more favorable compared to As(III), due to the faster kinetics of As(V) compared to As(III). Influence of the coexisting ions on the adsorption of As(V) and As(III) was studied. The applicability of the method for practical water samples was studied.     

The relationship between surface adsorption and the hydrolysis of amitraz in anionic surfactant solutions

The adsorption of amitraz to various adsorbents was studied in terms of the amount and rate of adsorption and the effect that adsorption had on the stability of amitraz in an aqueous environment. Adsorption results showed that in terms of their ability to adsorb amitraz from solution the adsorbents tested in this study can be ordered as follows: coarse carbon > cation exchange resin > or = anion exchange resin > fine carbon. Amitraz was not adsorbed on sand and potassium oxihumate. Adding sodium lauryl sulfate and potassium oxihumate to aqueous suspensions of suspended adsorbents containing adsorbed amitraz showed that both these anionic surfactants significantly increased the hydrolysis rate because the half-lives for amitraz was reduced from 27 days for a suspension to only 8 hours for amitraz adsorbed to a cation exchange resin and suspended in an aqueous buffer pH 5.8 containing 0.5% of the anionic surfactant sodium lauryl sulfate and 12 hours when 1% potassium oxihumate was added.     

KH-560交联壳聚糖固载β-环糊精薄膜对硝基苯酚的吸附行为

研究了KH-560交联壳聚糖固载β-环糊精薄膜对4-硝基苯酚、2,4-二硝基苯酚和2,4,6-三硝基苯酚的吸附行为,测定了吸附质浓度、pH、温度和吸附时间对其吸附性能的影响,并进行了热力学拟合。研究结果表明,在中性条件下,298K下吸附4-硝基苯酚在40min时可以达到平衡;随着硝基数目的增加,吸附量增大;随着温度的升高,吸附量减小;吸附过程用Langmuir模型描述更合适。