Is Levoglucosan a Suitable Quantitative Tracer for Wood Burning? Comparison with Receptor Modeling on Trace Elements in Lycksele,Sweden

Abstract

Particle emissions from residential wood combustion in small communities in Northern Sweden can sometimes increase the ambient particle concentrations to levels comparable to densely trafficked streets in the center of large cities. The reason for this is the combination of increased need for domestic heating during periods of low temperatures, leading to higher emission rates, and stable meteorological conditions. In this work, the authors compare two different approaches to quantify the wood combustion contribution to fine particles in Northern Sweden: a multivariate source-receptor analysis on inorganic compounds followed by multiple linear regression (MLR) of fine particle concentrations and levoglucosan used as a tracer. From the receptor model, it can be seen that residential wood combustion corresponds with 70% of modeled particle mass. Smaller contributions are also seen from local nonexhaust traffic particles, road dust, and brake wear (each contributing 14%). Of the mass, 1.5% is explained by long-distance transported particles, and 2% derives from a regional source deriving from either oil combustion or smelter activities.

In samples collected in ambient air, a significant linear correlation was found between wood burning particles and levoglucosan. The levoglucosan fraction in the ambient fine particulate matter attributed to wood burning according to the multivariate analysis ranged from <2% to 50%. This is much higher than the fraction found in the emission from the boilers expected to be responsible for most emissions at this site (between 3% and 6%). A laboratory emission study of wood and pellet boilers gave 0.3%_wt to 22%_wt levoglucosan to particle mass, indicating that the levoglucosan fraction may be highly dependent on combustion conditions, making it uncertain to use it as a quantitative tracer under real-world burning conditions. Thus, quantitative estimates of wood burning contributions will be very uncertain using solely levoglucosan as a tracer.     

The Compact Sequential Automatic Air Sampler

The body of information presented in this paper is directed to ecologists concerned with the effects and economic impact of sulfur dioxide on forest growth. Investigations were carried out over a ten-year period, 1953–1963, in the Sud-bury smelter district of Ontario, where three large smelters discharge annually approximately 2,000,000 tons of sulfur dioxide gas into the surrounding atmosphere. The study was designed to determine the long-term chronic effects of sulfur dioxide on yield, growth, and survival of plant life. Since eastern white pine is the most susceptible coniferous tree to sulfur dioxide injury, it was selected as the indicator tree to determine the degree and extent of injury in the Sudbury area. Tree data accumulated from the sample plots were correlated with records of atmospheric sulfur dioxide monitored continuously during the growing season by a network of ten strategically-located Thomas autometers. Based on the degree of injuries exhibited by the trees, and on air sampling records of sulfur dioxide, the Sudbury area was segregated into three fume zones: Inner, Intermediate, and Outer. An estimate was made of the loss in income suffered by the owners of wood or the producers of wood products in the Sudbury area as a result of sulfur dioxide air pollution, by utilizing the white pine volume growth loss data     

A Comprehensive Strategy to Reduce Residential Wood Burning Impacts in Small Urban Communities

Paniculate control strategies in the U.S. have historically focused on the reduction of industrial emissions. In recent years, however, area sources such as residential wood combustion have been recognized as significant and rapidly increasing sources of particulate emissions. In some areas of the country it will be necessary to substantially reduce residential wood burning emissions in order to attain or maintain acceptable levels of total and respirable particulate matter. A comprehensive strategy to reduce residential wood burning impacts has been developed for the Medford-Ashland area, 1 a community of about 100,000 population situated in a poorly ventilated valley in Oregon. Portions of this strategy will be applied in other areas of Oregon. The strategy may be applicable to urban communities in other states as well.     

Field-scale leaching of arsenic, chromium and copper from weathered treated wood

Earlier studies documented the loss of wood preservatives from new wood. The objective of this study was to evaluate losses from weathered treated wood under field conditions by collecting rainfall leachate from 5 different wood types, all with a surface area of 0.21 m². Wood samples included weathered chromate copper arsenate (CCA) treated wood at low (2.7 kg/m³), medium (4.8 kg/m³) and high (35.4 kg/m³) retention levels, new alkaline copper quat (ACQ) treated wood (1.1 kg/m³ as CuO) and new untreated wood. Arsenic was found to leach at a higher rate (100 mg in 1 year for low retention) than chromium and copper (<40 mg) in all CCA-treated wood samples. Copper leached at the highest rate from the ACQ sample (670 mg). Overall results suggest that metals' leaching is a continuous process driven by rainfall, and that the mechanism of release from the wood matrix changes as wood weathers.     

Is levoglucosan a suitable quantitative tracer for wood burning? Comparison with receptor modeling on trace elements in Lycksele, Sweden

Particle emissions from residential wood combustion in small communities in Northern Sweden can sometimes increase the ambient particle concentrations to levels comparable to densely trafficked streets in the center of large cities. The reason for this is the combination of increased need for domestic heating during periods of low temperatures, leading to higher emission rates, and stable meteorological conditions. In this work, the authors compare two different approaches to quantify the wood combustion contribution to fine particles in Northern Sweden: a multivariate source-receptor analysis on inorganic compounds followed by multiple linear regression (MLR) of fine particle concentrations and levoglucosan used as a tracer. From the receptor model, it can be seen that residential wood combustion corresponds with 70% of modeled particle mass. Smaller contributions are also seen from local nonexhaust traffic particles, road dust, and brake wear (each contributing 14%). Of the mass, 1.5% is explained by long-distance transported particles, and 2% derives from a regional source deriving from either oil combustion or smelter activities. In samples collected in ambient air, a significant linear correlation was found between wood burning particles and levoglucosan. The levoglucosan fraction in the ambient fine particulate matter attributed to wood burning according to the multivariate analysis ranged from < 2% to 50%. This is much higher than the fraction found in the emission from the boilers expected to be responsible for most emissions at this site (between 3% and 6%). A laboratory emission study of wood and pellet boilers gave 0.3% wt to 22% wt levoglucosan to particle mass, indicating that the levoglucosan fraction may be highly dependent on combustion conditions, making it uncertain to use it as a quantitative tracer under real-world burning conditions. Thus, quantitative estimates of wood burning contributions will be very uncertain using solely levoglucosan as a tracer.     

村镇小型生活垃圾热处理炉底渣的理化特性

小型垃圾热处理设备可实现就地处置,节约运输成本,目前在中国山区、丘陵地带的村镇得到广泛应用.为了解村镇小型生活垃圾热处理炉底渣的理化特性及其影响因素,对中国云南、贵州、安徽村镇实际运行的小型生活垃圾热处理设备产生的底渣进行取样,分析其热灼减率、物理组成、化学组成、晶相组成、重金属含量和浸出特性,探讨处理工艺、地域及季节...     

Occurrence of polychlorinated biphenyls (PCBs) together with sediment properties in the surface sediments of the Bering Sea, Chukchi Sea and Canada Basin

The spatial distribution and potential source of polychlorinated biphenyls (PCBs) in surface sediments from Bering Sea, Chukchi Sea, and Canada Basin and the relationship between PCBs and sedimentary properties including grain size, water content, loss on ignition, total organic carbon, and black carbon were explored. ΣPCBs (the sum of the detected PCB congeners) concentrations fluctuated in the study area, ranging from 22-150, 60-640 and 24-600 pg g(-1) dry weight for the Bering Sea, Chukchi Sea, and Canada Basin. A similar homologue pattern was observed at different locations, with tri-chlorinated PCBs being the dominant homologue, implying that the PCBs came mainly from the atmospheric transportation and deposition and ocean current transportation. No apparent co-relationships between PCB concentrations and sediment properties were obtained, indicating that the distribution of PCBs was not only controlled by their source, but also by the multi-factors such as atmospheric transport and depositing, mixing, partitioning and sorption in the water column and sediments.     

Transference of marine fouling communities between polluted and unpolluted sites: Impact on structure

Fouling communities were transferred between Wollongong Harbour (Australia), a relatively unpolluted area, and nearby Port Kembla Harbour which is affected by pollution from nearby heavy industries. Those that had been transferred from Wollongong Harbour were similar in structure after two months to those that had developed entirely in Port Kembla Harbour. Conversely, the communities transferred from Port Kembla Harbour had a similar structure to those that had developed only in Wollongong Harbour. Many of the species transferred from Wollongong Harbour were thought to have been killed by periodic high concentrations of pollutants or overgrown by more competitive species. Those few that survived the polluted conditions were mainly bryozoans and serpulids. Surprisingly, many supposedly pollution-tolerant species transferred from Port Kembla Harbour did not survive in Wollongong Harbour. It is suggested that this was because these animals could not tolerate the lower nutrient conditions in the latter area. Space once occupied by these species was quickly colonised by species found only in Wollongong Harbour. These results have important implications for the functioning of these communities.     

垃圾焚烧炉炉拱改造与燃烧优化的数值模拟

炉排式垃圾焚烧炉在处理比设计水分高、热值低的垃圾时,容易出现着火位置滞后、垃圾＂烧不透＂、残炭含量高等问题。采用FLIC软件的床层模型和商业软件FLUENT,对焚烧炉炉排和炉膛燃烧过程进行了模拟计算。结合某城市生活垃圾焚烧炉存在的燃烧不完全问题,通过一系列的数值实验,探索后拱高度和挡板的有无对燃烧过程的影响。比较了炉拱辐射强度、挥发分质量分数、温度沿炉排长度方向的分布以及炉膛内的速度矢量图。结果表明,降低后拱高度或增加挡板均可使着火位置有不同程度的前移;同时降低炉拱高度和增加挡板可使着火位置前移约1.1 m,提前进入稳定燃烧阶段。     

Emission factors of particulate matter,polycyclic aromatic hydrocarbons,and levoglucosan from wood combustion in south-central Chile

In south-central Chile, wood stoves have been identified as an important source of air pollution in populated areas. Eucalyptus (Eucalyptus globulus), Chilean oak (Nothofagus oblique), and mimosa (Acacia dealbata) were burned in a single-chamber slow-combustion wood stove at a controlled testing facility located at the University of Concepción, Chile. In each experiment, 2.7–3.1 kg of firewood were combusted while continuously monitoring temperature, exhaust gases, burn rate, and collecting particulate matter samples in Teflon filters under isokinetic conditions for polycyclic aromatic hydrocarbon and levoglucosan analyses. Mean particulate matter emission factors were 2.03, 4.06, and 3.84 g/kg dry wood for eucalyptus, oak, and mimosa, respectively. The emission factors were inversely correlated with combustion efficiency. The mean emission factors of the sums of 12 polycyclic aromatic hydrocarbons in particle phases were 1472.5, 2134.0, and 747.5 μg/kg for eucalyptus, oak, and mimosa, respectively. Fluoranthene, pyrene, benzo[a]anthracene, and chrysene were present in the particle phase in higher proportions compared with other polycyclic aromatic hydrocarbons that were analyzed. Mean levoglucosan emission factors were 854.9, 202.3, and 328.0 mg/kg for eucalyptus, oak, and mimosa, respectively. Since the emissions of particulate matter and other pollutants were inversely correlated with combustion efficiency, implementing more efficient technologies would help to reduce air pollutant emissions from wood combustion.

Implications: Residential wood burning has been identified as a significant source of air pollution in populated areas. Local wood species are combusted for home cooking and heating, which releases several toxic air pollutants, including particulate matter, carbon monoxide, and polycyclic aromatic hydrocarbons. Air pollutant emissions depend on the type of wood and the technology and operational conditions of the wood stove. A better understanding of emissions from local wood species and wood stove performance would help to identify better biomass fuels and wood stove technologies in order to reduce air pollution from residential wood burning.     

Indoor pollution and burning practices in wood stove management

This study evaluates effects of good burning practice and correct installation and management of wood heaters on indoor air pollution in an Italian rural area. The same study attests the role of education in mitigating wood smoke pollution. In August 2007 and winters of 2007 and 2008, in a little mountain village of Liguria Apennines (Italy), indoor and outdoor benzene, toluene, ethylbenzene, and xylene (BTEX) concentrations were measured in nine wood-heated houses. During the first sampling, several mistakes in heating plant installations and management were found in all houses. Indoor BTEX concentrations increased during use of wood burning. Low toluene/benzene ratios were in agreement with wood smoke as main indoor and outdoor pollution source. Other BTEX sources were identified as the indoor use of solvents and paints and incense burning. Results obtained during 2007 were presented and discussed with homeowners. Following this preventive intervention, in the second winter sampling all indoor BTEX concentrations decreased, in spite of the colder outdoor air temperatures. Information provided to families has induced the adoption of effective good practices in stoves and fire management. These results highlight the importance of education, supported by reliable data on air pollution, as an effective method to reduce wood smoke exposures.

Implications:Information about burning practices and correct installation and management of wood heaters, supported by reliable data on indoor and outdoor pollution, may help to identify and remove indoor pollution sources. This can be an effective strategy in mitigate wood smoke pollution.     

Genotoxicity biomarkers and acetylcholinesterase activity in natural populations of Mytilus galloprovincialis along a pollution gradient in the Gulf of Oristano (Sardinia, western Mediterranean)

A year-round biomonitoring study on blue mussels (Mytilus galloprovincialis) was carried out in 4 selected sites along the Gulf of Oristano (Sardinia, Italy): a commercial port (Port), the outlet of the S'Ena Arrubia and Marceddì lagoons (in the catchment area of intensive agricultural and diary activities, and abandoned mining), and a reference site (North). Heavy metal concentrations in sediments from Marceddì were 2-3 to 10-20 times higher in Pb, Cd and Zn, respectively, than those found at North and S'Ena Arrubia. Higher values (P<0.05) of micronuclei frequency were detected in mussels from Marceddì and Port compared to those detected in mussels from North and S'Ena Arrubia. DNA damage in animals from North was significantly lower than that at the other sites. Results of acetylcholinesterase inhibition consistently showed the strongest effects in mussels from Port and Marceddì. Our results suggest that these biomarkers can be used in coastal marine biomonitoring as early signals of exposure and adverse effects along a pollution gradient.     

Source apportionment of visual impairment during the California regional PM10/PM2.5 air quality study

Gases and particulate matter predictions from the UCD/CIT air quality model were used in a visibility model to predict source contributions to visual impairment in the San Joaquin Valley (SJV), the southern portion of California's Central Valley, during December 2000 and January 2001. Within the SJV, daytime (0800–1700 PST) light extinction was dominated by scattering associated with airborne particles. Measured daytime particle scattering coefficients were compared to predicted values at approximately 40 locations across the SJV after correction for the increased temperature and decreased relative humidity produced by “smart heaters” placed upstream of nephelometers. Mean fractional bias and mean fractional error were ?0.22 and 0.65, respectively, indicating reasonable agreement between model predictions and measurements. Particulate water, nitrate, organic matter, and ammonium were the major particulate species contributing to light scattering in the SJV. Daytime light extinction in the SJV averaged between December 25, 2000 and January 7, 2001 was mainly associated with animal ammonia sources (28%), diesel engines (18%), catalyst gasoline engines (9%), other anthropogenic sources (9%), and wood smoke (7%) with initial and boundary conditions accounting for 13%. The source apportionment results from this study apply to wintertime conditions when airborne particulate matter concentrations are typically at their annual maximum. Further study would be required to quantify source contributions to light extinction in other seasons.     

Assessment of airborne heavy metal pollution by aboveground plant parts

Italian stone pine (Pinus pinea L.) and oleander (Nerium oleander L.) leaves, bark and wood samples were collected at different sites around an industrial area (Huelva, SW Spain) and compared with samples of the same species from a background site. Samples were analysed with respect to the following pollutants: Al, Ba, Cr, Cu, Fe and Pb by ICP-AES. The suitability of different plant parts as biomonitors of pollution was investigated. In pine samples from the polluted sites the ratio of concentrations between bark and wood was high for Al, Ba, Cu and Fe, whereas no differences were found in samples from the unpolluted area. No differences were detected in oleander for the same ratio. In the oleander species, the ratio between leaves and wood concentration allowed to distinguish between control and polluted sites. The ratio of the concentration between leaves and wood was elevated for Al, Ba and Fe in pine samples from the polluted sites. The ratio of the concentration in bark or leaves to their concentration in wood might be useful to detect inorganic atmospheric pollutants.     

Carbon budgets for catchments across a managed landscape mosaic in southeast Sweden: contributing to the safety assessment of a nuclear waste repository

Ecosystem budgets of matter contribute to the assessment of transport and accumulation of bioavailable contaminants in a landscape, since flows of matter and energy ultimately determine the rates at which contaminants will be partitioned in the environment. This study compares ecosystem properties, such as net primary production (NPP), sequestration of matter and fluxes to food sources for humans, which are of potential interest to describe fluxes and accumulation of bioavailable radionuclides in 14 catchments within a larger catchment area in southeast Sweden. The carbon budgets, used as a proxy for organic matter, are mainly based on local estimates of pools and fluxes, which have been distributed across a landscape mosaic of different vegetation types and management regimes using a geographical information system (GIS). NPP varied by a factor close to two (432 - 709 g x Cx m(-2)x y(-1)), while net ecosystem production ranged between -124 and 159 gx C x m(-2) x y (-1) for the different catchments. Carbon sequestration mainly occurred in the vegetation while the soil organic carbon pool was mainly a source of carbon. Large herbivores consumed on average 4.5 % of the above-ground green tissue production. When arable land was present in the catchment, the flux of carbon to humans was highest from crops and, in decreasing order, milk and beef, followed by the flux from hunting and berry/fungus picking. The results can be used to estimate the potential assimilation of radionuclides in vegetation and the potential exposure to humans of bioavailable radionuclides.     

Comparison of source apportionments of fine particulate matter at two San Jose speciation trends network sites

In this study, the chemical composition of fine particulate matter samples collected at U.S. Environmental Protection Agency Speciation Trends Network sites in San Jose, CA, from February 2000 to February 2005 were analyzed. A San Jose site was initially established at 4th Street and then subsequently moved to Jackson Street in mid-2002. These sites are approximately 1 km apart. There were no known major changes in the nature of the sources in the area over this period. The study used positive matrix factorization model to extract the source profiles and their mass contributions and to compare the results for the congruence of the source apportionments between these two nearby sites. In the case of the 4th Street site, the average mass was apportioned to wood combustion (32.1 +/- 2.5%), secondary nitrate (22.3 +/- 2%), secondary sulfate (10.7 +/- 0.6%), fresh sea salt (7.7 +/- 0.9%), gasoline vehicles (7.3 +/- 0.5%), aged sea salt (6.8 +/- 0.4%), road dust (6.7 +/- 0.7%), diesel emissions (3.9 +/- 0.3%), and a Ni-related industrial source (2.5 +/- 0.4%). At the Jackson Street site, the average mass was apportioned to wood combustion (33.6 +/- 2.6%), secondary nitrate (20.3 +/- 1.9%), secondary sulfate (13.9 +/- 0.9%), aged sea salt (12.4 +/- 0.7%), gasoline vehicle (8.3 +/- 0.6%), fresh sea salt (5.3 +/- 0.5%), diesel emission (3.2 +/- 0.3%), road dust (1.9 +/- 0.1%), and Ni-related industrial source (1.3 +/- 0.1%). Conditional probability function analysis was used to help identify local sources. These results suggested that moving the sampling site a short distance had little effect on the nature of the resolved source types although some differences in their quantitative impacts were obtained in the positive matrix factorization analyses.     

Resource recycling through artificial lightweight aggregates from sewage sludge and derived ash using boric acid flux to lower co-melting temperature

This study focuses on artificial lightweight aggregates (ALWAs) formed from sewage sludge and ash at lowered co-melting temperatures using boric acid as the fluxing agent. The weight percentages of boric acid in the conditioned mixtures of sludge and ash were 13% and 22%, respectively. The ALWA derived from sewage sludge was synthesized under the following conditions: preheating at 400 °C 0.5 hr and a sintering temperature of 850 °C 1 hr. The analytical results of water adsorption, bulk density, apparent porosity, and compressive strength were 3.88%, 1.05 g/cm³, 3.93%, and 29.7 MPa, respectively. Scanning electron microscope (SEM) images of the ALWA show that the trends in water adsorption and apparent porosity were opposite to those of bulk density. This was due to the inner pores being sealed off by lower-melting-point material at the aggregates' surface. In the case of ash-derived aggregates, water adsorption, bulk density, apparent porosity, and compressive strength were 0.82%, 0.91 g/cm³, 0.82%, and 28.0 MPa, respectively. Both the sludge- and ash-derived aggregates meet the legal standards for ignition loss and soundness in Taiwan for construction or heat insulation materials.

Implications Artificial lightweight aggregates (ALWAs) could be synthesized from sewage sludge and derived ash. In this study, co-melting technology of low temperature was applied with boric acid as a fluxing agent and the formation temperature of glass phase was decreased to 900 °C. Both aggregates derived from sludge and ash meet regulatory standards of ignition loss and soundness in Taiwan for construction or heat insulation material.     

Air pollutant concentrations near three Texas roadways, part II: Chemical characterization and transformation of pollutants

Spatial gradients of vehicular emitted air pollutants were measured in the vicinity of three roadways in the Austin, Texas area: (1) State Highway 71 (SH-71), a heavily traveled arterial highway dominated by passenger vehicles; (2) Interstate 35 (I-35), a limited access highway north of Austin in Georgetown; and (3) Farm to Market Road 973 (FM-973), a heavily traveled surface roadway with significant truck traffic. A mobile monitoring platform was used to characterize the gradients of CO and NO_x concentrations with increased distance from each roadway, while concentrations of carbonyls in the gas-phase and fine particulate matter mass and composition were measured at stationary sites upwind and at one (I-35 and FM-973) or two (SH-71) downwind sites. Regardless of roadway type or wind direction, concentrations of carbon monoxide (CO), nitric oxide (NO), and oxides of nitrogen (NO_x) returned to background levels within a few hundred meters of the roadway. Under perpendicular wind conditions, CO, NO and NO_x concentrations decreased exponentially with increasing distance perpendicular to the roadways. The decay rate for NO was more than a factor of two greater than for CO, and it comprised a larger fraction of NO_x closer to the roadways than further downwind suggesting the potential significance of near roadway chemical processing as well as atmospheric dilution. Concentrations of most carbonyl species decreased with distance downwind of SH-71. However, concentrations of acetaldehyde and acrolein increased farther downwind of SH-71, suggesting chemical generation from the oxidation of primary vehicular emissions. The behavior of particle-bound organic species was complex and further investigation of the size-segregated chemical composition of particulate matter (PM) at increasing downwind distances from roadways is warranted. Fine particulate matter (PM_2.5) mass concentrations, polycyclic aromatic hydrocarbons (PAHs), hopanes, and elemental carbon (EC) concentrations generally exhibited concentrations that decreased with distance downwind of SH-71. Concentrations of organic carbon (OC) increased from upwind concentrations immediately downwind of SH-71 and continued to increase further downwind from the roadway. This behavior may have primarily resulted from condensation of semi-volatile organic species emitted from vehicle sources with transport downwind of the roadway.     

平板炭气凝胶电极电吸附除氟

采用自制的炭气凝胶平板电极进行模拟水样中氟的电吸附去除研究,通过单因子实验优化了该电吸附技术的操作参数和适用的溶液条件,并研究了反接电极法的再生效果。研究结果表明,自制的炭气凝胶平板由纳米颗粒组成三维网络结构,比表面积为670.90 m2/g,具有良好的充放电可逆性和迅速形成表面双电层的特点。静态电吸附除氟效果最佳的条件为:水样氟离子浓度6 mg/L,pH 7.0,极板间距4 cm,电压1.6 V;共存物质硝酸根、腐殖酸、碳酸根和碳酸氢根等对氟离子的电吸附具有一定的促进作用。吸附氟离子后的炭气凝胶材料的比表面、孔体积、电容值有所减小。对于吸附氟离子后的炭气凝胶平板电极,采用反接电极法取得较好再生效果的条件为:流动状态、电压1.6 V、极板间距4 cm。再生后的炭气凝胶电极与原始炭气凝胶相比,依然具有良好的充放电可逆性。     

Distribution of Al-, Fe- and Mn-pools and their correlation in soils from two acid deposition small catchments in Hunan, China

Distribution of Al-, Fe- and Mn-pools was investigated in five forest soil profiles (consisting of four horizons) in each of two Hunan catchments (BLT and LKS) where acid deposition has been considered critical. Al- and Fe-pools were higher in BLT than those in LKS, but Mn-pools much lower in BLT. Mn-pools vary from topsoils to bottom soils, but there are different trends for different Mn speciation. Al- and Fe-pools, except amorphous Fe_ox, were positively correlated to contents of soil organic matter (OM) showed by the loss on ignition in the two catchments. Accumulation of Al- and Fe-pools may occur in the area where soil organic matter was enriched (e.g. in top soil and rhizosphere soil). However, no direct correlation is observed between Mn and OM. Acidic atmospheric deposition may affect transforming among speciations of Al-, Fe- and Mn-pools and leaching of soil Al, Fe and Mn through formation of soluble organo-metal dissolved Al which was potentially toxic, increased. There were significant correlations between Al-pools complexes or change of oxidation–reduction conditions. Mn_ex (exchangeable Mn) and Mn_ox (amorphous and organic Mn) were highly linearly correlation with soil pH values at LKS but at BLT. Under acid deposition, the availability of the nutrient Fe increased with the amount of dissolved Al, which was potentially toxic, in the two catchments. There are no significant correlations between Al_ex (exchangeable Al) and Mn_ex, Fe_ex (exchangeable Fe) and Mn_ex in this work, indicating potentially toxic Mn increase seldom accompanying with Al increase in the two catchments.