The long-term effect of initial pH control on the enrichment culture of phosphorus- and glycogen-accumulating organisms with a mixture of propionic and acetic acids as carbon sources

In most studies on phosphorus- and glycogen-accumulating organisms (PAO and GAO), pH was controlled constantly throughout the entire anaerobic and aerobic periods, and acetic acid was used as the carbon source. In this paper, the effect of long-term initial pH values on PAO and GAO was investigated with mixed propionic and acetic acids as carbon sources. It was observed that with pH increasing from 6.4 to 8.0, the anaerobic propionic acid uptake rate by PAO linearly increased but that by GAO proportionally decreased. At pH 6.70 and pH 7.51, PAO and GAO exhibited the same acetic and propionic acid uptake rates, respectively. The acetic acid uptake rate by PAO was greater than that by GAO at pH > 6.70, and the propionic acid uptake rate by PAO was higher than that by GAO at pH > 7.51, which indicated that PAO would take predominance over GAO at pH > 7.51. Poly-3-hydroxybutyrate, poly-3-hydroxyvalerate and poly-3-hydroxy-2-methylvalerate shared 7%, 62% and 31%, respectively in the PAO system, and 11%, 44% and 45% respectively in the GAO system, and these fractions were observed independent of pH either in the PAO or in the GAO system. In the PAO system, with the increase of pH, the phosphorus removal efficiency was improved greatly, and a phosphorus removal efficiency of 100% was achieved at 8.0. Further investigation showed that the higher phosphorus removal efficiency at higher pH was mainly caused by a biological effect instead of chemical one.     

Effect of short-chain organic acids and pH on the behaviors of pyrene in soil–water system

The effects of five short-chain organic acids (SCOAs) on the behaviors of pyrene in soil–water system were investigated. The influences of the quantity and species of organic acids, pH, and soil dissolved organic matter were considered. The results showed the presence of SCOAs inhibited the adsorption and promoted the desorption of pyrene in the following order: citric acid > oxalic acid > tartaric acid > lactic acid > acetic acid. The decreased extents of pyrene adsorption performance enhanced with increasing SCOA concentrations, while the decreasing rate became less pronounced at high SCOA concentrations. In the presence of organic acids, the adsorption ability of pyrene decreased with increasing pH. However, there was a slight increase of pyrene adsorption with the addition of oxalic acid, tartaric acid and citric acid above pH 8. The capacity for pyrene retention differentiated significantly between the soils with and without dissolved organic matter. The presence of SCOAs was also favorable for the decrease of pyrene adsorption on soil without dissolved organic matter. The results of this study have important implications for the remediation of persistent organic pollutants in soil and groundwater.     

Emissions of volatile fatty acids from feed at dairy facilities

Recent studies suggest that dairy operations may be a major source of non-methane volatile organic compounds in dairy-intensive regions such as Central California, with short chain carboxylic acids (volatile fatty acids or VFAs) as the major components. Emissions of four VFAs (acetic acid, propanoic acid, butanoic acid and hexanoic acid) were measured from two feed sources (silage and total mixed rations (TMR)) at six Central California Dairies over a fifteen-month period. Measurements were made using a combination of flux chambers, solid phase micro-extraction fibers coupled to gas chromatography mass spectrometry (SPME/GC–MS) and infra-red photoaccoustic detection (IR-PAD for acetic acid only). The relationship between acetic acid emissions, source surface temperature and four sample composition factors (acetic acid content, ammonia-nitrogen content, water content and pH) was also investigated. As observed previously, acetic acid dominates the VFA emissions. Fluxes measured by IR-PAD were systematically lower than SPME/GC–MS measurements by a factor of two. High signals in field blanks prevented emissions from animal waste sources (flush lane, bedding, open lot) from being quantified. Acetic acid emissions from feed sources are positively correlated with surface temperature and acetic acid content. The measurements were used to derive a relationship between surface temperature, acetic acid content and the acetic acid flux. The equation derived from SPME/GC–MS measurements predicts estimated annual average acetic acid emissions of (0.7 + 1/?0.4) g m^?2 h^?1 from silage and (0.2 + 0.3/?0.1) g m^?2 h^?1 from TMR using annually averaged acetic acid content and meteorological data. However, during the summer months, fluxes may be several times higher than these values.     

Impact of recent urbanization on formic and acetic acid concentrations in coastal North Carolina rainwater

Concentrations of formic and acetic acids in Wilmington, North Carolina, USA, rainwater collected between 1996 and 1998 have increased dramatically since an earlier study conducted at the same site between 1987 and 1989. The current volume-weighted concentrations of acetic acid are within the range of values reported for urban locations whereas values from the earlier study at this site were similar to those obtained for rural locations. The ratios of formic to acetic acids (F : A) in the current study (approximately 1 : 1) are considerably lower than those previously reported (approximately 2.7 : 1). Current F : A's are similar to F : A's from direct automobile emissions. Increases in formic and acetic acid concentrations and the shift in formic to acetic acid ratios likely reflect the impact of extensive population growth in the surrounding region. Assuming increases in formic and acetic acid concentrations result from increased anthropogenic sources, we estimate at least 1/2 of the formic and at least 2/3 of the acetic acid in Wilmington, NC growing season rainwater results from anthropogenic sources.     

Wet deposition of low molecular weight mono- and di-carboxylic acids,aldehydes and inorganic species in Los Angeles

About 60 rainwater samples were collected at west Los Angeles, California in 1981–1984 and were analyzed for C₁–C₉ monocarboxylic acids (0.33–79 μM, average (av.) 13±15 μM), C₂–C₁₀ dicarboxylic acids (2.9–51 μM, av. 7.5±14 μM) and C₁–C₄ aldehydes (0.85–28 μM, av. 9.2±11 μM). Distributions of monocarboxylic acids show a predominance of formic (average concentration: 6.5 μM) and acetic (av. 5.6 μM) acids followed by propionic acid (av. 0.44 μM). Oxalic acid is the dominant diacid (av. 3.9 μM) followed by succinic acid (av. 1.0 μM). Formaldehyde (av. 6.9 μM) is the dominant aldehyde, with the next most abundant, acetaldehyde, being minor (av. 0.65 μM). For select rain samples described in this paper, were found to comprise monocarboxylic acids 0.9–12.3% (av. 4.4±3.4%), diacids comprise 1.2–9.5% (av. 4.2±3.3%) and aldehydes comprise 0.2–6.2% (av. 2.1±2.2%) of total organic carbon (TOC, 2.0–18.6 mg C l⁻¹; av. 9.8±5.4 mg C l⁻¹). Annual rain fluxes of monocarboxylic acids and aldehydes during 1982–1983 were calculated to be 0.24 and 0.11 g m⁻² yr⁻¹, respectively, with an annual estimated wet deposition in the Los Angeles Basin of 3120 and 1430 tons, respectively. These fluxes are equivalent to 2500 times of the acids and 2.5 times of the aldehydes emitted from automobile exhausts in the Los Angeles air basin. This comparison suggests that major portions of the carboxylic acids detected in the rain are not directly emitted from auto-exhausts, but are most likely produced in the atmosphere by gaseous and/or aqueous phase photo-induced reactions.     

Removal of aqueous lead by poorly-crystalline hydroxyapatites

The use of a phosphorus amendment in altering Pb to a chemically less mobile phase is a promising strategy based on minimizing ecotoxicological risk and improving time and cost efficiency. This study evaluated crystalline and poorly-crystalline hydroxyapatite sorbents on removal of aqueous Pb in response to reaction time, solution pH, and Pb concentration. Batch experiments were conducted using a commercially-available crystalline hydroxyapatite (HA), and two poorly-crystalline hydroxyapatites synthesized from gypsum waste (CHA) and incinerated ash of poultry waste (MHA). Poorly-crystalline hydroxyapatites had greater capacity for Pb removal from a solution with a wider pH range as compared to a crystalline hydroxyapatite. The maximum sorption capacity of Pb determined by the Langmuir model was 500 mg g⁻¹ for CHA, 277 mg g⁻¹ for MHA and 145 mg g⁻¹ for HA. Removal of aqueous Pb by CHA was not dependent on solution pH, with a 98.8% reduction throughout the solution pH range of 2–9, whereas aqueous Pb removal by HA and MHA was pH-dependent with less removal in the neutral solution pH. Poorly-crystalline hydroxyapatites may provide an effective alternative to existing remediation technologies for Pb-contaminated sites.     

Factors controlling the emissions of volatile organic acids from leaves of Quercus ilex L. (Holm oak)

Direct emissions and emission of precursor compounds of acetic and formic acid from higher plants are a significant source of these acids in the atmosphere. To travel from the plant cell to the atmosphere, a gas molecule must first leave the liquid phase and then enter the internal leaf gas phase. The apoplast (cell wall) is the last barrier before the molecule can escape through the stomata. During field experiments we monitored the gas exchange (H₂O, CO₂, organic acids) of Quercus ilex L. leaves. The exchange rates of acetic and formic acid under field conditions followed a typical diurnal pattern and ranged between −10 (uptake) and 52 (emission) nmol m^-2 leaf area min^-1 with the maximum around noon. Growth chamber experiments indicate that the emission is related to the stomatal conductance. We discussed the exchange rate of organic acids between the cell wall and the atmosphere in connection with Henry’s law, and the physicochemical conditions in the cell wall. The evaluation showed that for apoplastic pH values between 4 and 5, 26–130% of the measured acetic acid emission based on leaf area could be predicted.     

The performance of a gas and aerosol monitoring system (GAMS) for the determination of acidic water soluble organic and inorganic gases and ammonia as well as related particles from the atmosphere

A new application of the quasi-simultaneous gas/particle phase sampling and analysis principle first proposed by Simon and Dasgupta (Anal. Chem. 34 (1995) 71) is described. For the first time, a gradient chromatograph is used in connection with such a sampling system to allow the simultaneous determination of major organic (formic, acetic, propionic, oxalic, malonic and succinic) and inorganic (SO₂, HNO₂, HNO₃, HCl and H₂F₂) acidic gases and related particles. Another addition to the previous systems is the analysis of cations other than ammonium from the particulate phase. The time resolution of the instrument still remains high, 1 h, during which gaseous water-soluble acidic compounds, ammonia, as well as related anionic particles and inorganic major cations are analysed. Sampling is based on diffusion in a wetted parallel plate denuder for gases and on growth in supersaturated water vapour for particles. The determination limits range from 2 ppt (acetate) to 0.4 ppb (ammonia) in the gas phase and 0.01 μg m⁻³ (citric acid) to 0.79 μg m⁻³ (calcium) for particulate matter. Collection efficiencies for gas and aerosol sampling were quantified and the supersaturation in the aerosol sampling apparatus investigated. The system has been used for field measurements at a background station; selected results of these measurements are presented.     

Comparison of monometal and multimetal adsorption in Mississippi River alluvial wetland sediment: Batch and column experiments

Monometal and multimetal adsorption of selected heavy metals in a sediment from a coastal Louisiana forested swamp used for wastewater treatment was studied. Results from the batch experiments show that the maximum adsorption capacities of the metals by the sediment were in the order of Pb ≫ Hg > Cr > Cd ⩾ Cu ⩾ Zn ≫ As based on monometal adsorption isotherm, and Hg > Cr > Cu ⩾ Cd ≈ Pb ≫ As ≈ Zn based on multimetal adsorption isotherm, respectively. Batch experimental data best fit the Langmuir model rather than the Freundlich isotherms. In the column experiments, the maximum adsorption capacities of the metals were in the order of Pb ≫ Hg > Cr > Cd > Cu > Zn ≫ As in monometal conditions, and Hg ≫ Cr ≫ Pb > Cu ⩾ Zn ≈ Cd > As in multimetal conditions. The metals became more mobile in multimetal than in monometal conditions. Results from both the batch and column experiments show that competitive adsorption among metals increases the mobility of these metals. Particularly, in this study, Pb in multimetal conditions lost it adsorption capacity most significantly. In both monometal and multimetal conditions, the maximum adsorption capacity of the metals in the column experiments was higher than that in the batch experiment indicating other metal retention mechanisms rather than adsorption may be involved. Therefore, both column and batch experiments are needed for estimating retention capacities and removal efficiencies of metals in sediments.     

Influence of water quality parameters on occurrence of polybrominated diphenyl ether in sediment and sediment to biota accumulation

Polybrominated diphenyl ether (PBDE) concentrations in sediment and fish from 12 principal rivers in Taiwan were investigated to determine their association with water quality parameters as well as the biota-sediment accumulation factor (BSAF) in fish with different living patterns. The highest PBDE concentration in sediment was found in the Bajhang River (261 ng g^?1 dry weight (d.w.)) and the lowest in the Beinan River and the Da-an River (0.17 ng g^?1 d.w.). The PBDE concentrations in fish samples ranged from 1.28 ng g^?1 d.w. (Oreochromis niloticus niloticus) in the Yanshuei River to 33.7 ng g^?1 d.w. (Varico rhinos barbatulus) in the Da-an River. We conclude that PBDEs contamination in sediment was significantly affected by NH₃–N, pH, and DO. The BSAF results showed a parabolic trend from low- to high-brominated BDEs. Fish easily accumulated the congeners BDE-47, -100, -119, -126, and -154 from sediment. The BSAF decreased in the following order: PeBDE > HxBDE > TeBDE > other BDEs. Principle component analysis showed that demersal fish have different PBDE sources than do pelagic fish. We conclude that living and feeding habits are critical factors affecting PBDE accumulation in fish.     

Regulated and speciated hydrocarbon emissions from a catalyst equipped internal combustion engine

In the present work, the effect of engine operating conditions on its exhaust emissions and on catalytic converter operation is studied. A 4-cylinder OPEL 1.6 l internal combustion engine equipped with a hydraulic brake dynamometer was used in all the experiments. For exhaust emissions treatment a typical three-way catalyst was used. The highest hydrocarbon and carbon monoxide engine-out emissions were observed at engine power 2–4 HP. These emissions were decreased as the engine power was increased up to 20 HP. Among the various compounds detected in exhaust emissions, the following ones were monitored at engine and catalyst outlet: methane, hexane, ethylene, acetaldehyde, acetone, benzene, toluene and acetic acid. The concentration of each compound in the catalytic converter effluent was in the range 45–132, 5–12, 10–125, 15–22, 3–7, 3–12, 2–9, 0–6 ppm, respectively. After the required temperature for catalyst operation had been achieved, carbon monoxide tailpipe emissions were dramatically decreased and the observed hydrocarbon conversions were also high. Methane was the most resistant compound to oxidation while ethylene was the most degradable compound over the catalyst. The order from the easiest to the most resistant to oxidation compound was: Alkene>Aromatic>Aldehyde>Ketone>Alkane.     

Concentrations of perfluoroalkyl compounds in maternal and umbilical cord sera and birth outcomes in Korea

This study analyzed the concentrations of perfluorooctane sulfonate (PFOS), perfluorooctanoic acid (PFOA) and perfluorohexane sulfonate (PFHxS) in maternal and umbilical cord sera at delivery from the general population in Korea. Seventy samples were analyzed with ion-pairing and LC/MS/MS. PFOS, PFOA and PFHxS were detected in both maternal and umbilical cord sera. There was a high correlation of PFC concentrations between maternal and cord serum samples, implying transplacental transport. Ranking of transplacental transfer efficiency was PFOA > PFHxS > PFOS. Student’s t-tests revealed that concentrations of maternal PFOA were related with decreases in birth weight, birth length and ponderal index, suggesting a possible impact on fetal growth. With multiple logistic regression models, maternal PFOS concentration showed a significant inverse association with ponderal index (OR = 0.22; 95% CI, 0.05–0.90). Umbilical cord PFHxS concentration showed a significant inverse association with birth weight (OR = 0.26; 95% CI, 0.08–0.85) or a marginally significant inverse association with birth length (OR = 0.33; 95% CI, 0.09–1.17). This is the first report demonstrating an inverse association of birth outcomes with PFHxS exposure. Concentrations of maternal PFOA were decreased with parity, implying that delivery is one of the major routes for PFOA elimination in women. This study demonstrated prenatal exposure of PFCs through placental transfer which could result in possible developmental effects in the population sampled. Our results may provide data basis to conduct a larger scale investigation into developmental effects of PFCs in the future and contribute to understanding levels of PFC contaminations from a variety of populations in the globe.     

Effect of copper(II) on biodegradation of benzo[a]pyrene by Stenotrophomonas maltophilia

Benzo[a]pyrene (BaP) biodegradation by Stenotrophomonas maltophilia was studied under the influence of co-existed Cu(II) ions. About 45% degradation was achieved within 3 d when dealing with 1 mg L^?1 BaP under initial natural pH at 30 °C; degradation reached 48% in 2 d at 35 °C. Efficacy of BaP biodegradation reached the highest point at pH 4. In the presence of 10 mg L^?1 Cu(II) ions, the BaP removal ratio was 45% on 7th day, and maintained stable from 7 to 14 d at 30 °C under natural pH. The favorable temperature and pH for BaP removal was 25 °C and 6.0 respectively, when Cu(II) ions coexisted in the solutions. Experiments on cometabolism indicated that S. maltophilia performed best when sucrose was used as an additional carbon source. GC–MS analysis revealed that the five rings of BaP opened, producing compounds with one or two rings which were more bioavailable.     

Pre- and post-catalyst-, fuel-, velocity- and acceleration-dependent benzene emission data of gasoline-driven EURO-2 passenger cars and light duty vehicles

The benzene emission characteristics of six gasoline-driven EURO-2 vehicles, three passenger cars and three light duty vehicles, have been determined by time-resolved chemical ionization mass spectrometry. Aliquots of the exhaust gas were monitored pre- and post-catalyst with two independently operating mass spectrometers. Each vehicle was driven with two different fuels having benzene contents of 1 and 2 vol%. Seven driving cycles—including the European (EDC) and the US (FTP-75) driving cycle—with a total driving time of about 8800 s were studied. Herein, we discuss the average emission characteristics of the entire fleet at transient driving in the velocity range of 0–150 km h⁻¹. The conversion efficiencies of the involved catalytic systems were deduced from the pre- and post-catalyst data. On average, the vehicles showed optimal benzene conversion efficiencies (>95%) in the velocity range of 30–90 km h⁻¹. When driving below 20 or above 100 km h⁻¹ reduced benzene conversion was found (80–82%). No benzene conversion was observed when driving above 130 km h⁻¹. In contrast, the post-catalyst benzene emissions exceeded those of the untreated exhaust gas by 19–49%. Thus on an average, benzene was formed across the catalysts under these conditions. In addition, the influence of the benzene content of the gasoline on the tail-pipe emissions was also studied. The use of the gasoline with 1 vol% benzene instead of 2 vol% induced a 20–30% reduction of the post-catalyst emissions when driving below 50 km h⁻¹. The fuel effect became smaller above 100 km h⁻¹ and was even negative at high engine load (>130 km h⁻¹). Thus under these conditions, when benzene is formed across the catalyst, the amount of the emitted benzene was independent of the benzene level of the fuel.     

Speciation of volatile organic compounds from poultry production

Volatile organic compounds (VOCs) emitted from poultry production are leading source of air quality problems. However, little is known about the speciation and levels of VOCs from poultry production. The objective of this study was the speciation of VOCs from a poultry facility using evacuated canisters and sorbent tubes. Samples were taken during active poultry production cycle and between production cycles. Levels of VOCs were highest in areas with birds and the compounds in those areas had a higher percentage of polar compounds (89%) compared to aliphatic hydrocarbons (2.2%). In areas without birds, levels of VOCs were 1/3 those with birds present and compounds had a higher total percentage of aliphatic hydrocarbons (25%). Of the VOCs quantified in this study, no single sampling method was capable of quantifying more than 55% of compounds and in several sections of the building each sampling method quantified less than 50% of the quantifiable VOCs. Key classes of chemicals quantified using evacuated canisters included both alcohols and ketones, while sorbent tube samples included volatile fatty acids and ketones. The top five compounds made up close to 70% of VOCs and included: 1) acetic acid (830.1 μg m^?3); 2) 2,3-butanedione (680.6 μg m^?3); 3) methanol (195.8 μg m^?3); 4) acetone (104.6 μg m^?3); and 5) ethanol (101.9 μg m^?3). Location variations for top five compounds averaged 49.5% in each section of the building and averaged 87% for the entire building.     

Formation of strong airway irritants in a model mixture of (+)-α-pinene/ozone

The airway irritation of (+)-α-pinene, ozone, mixtures thereof, and formaldehyde was evaluated by a mouse bioassay, in which sensory irritation, bronchoconstriction, and pulmonary irritation were measured. The effects are distinguished by analysis of the respiratory parameters. Significant sensory irritation (assessed from reduction of mean respiratory rate) was observed by dynamic exposure of the mice, over a period of 30 min, to a ca. 22 s old reaction mixture of ozone and (+)-α-pinene from a Teflon flow tube. The starting concentrations were 6 ppm and 80 ppm, respectively, which were diluted and let into the exposure chamber. About 10% ozone remained unreacted (0.4 ppm), <0.2 ppm formaldehyde, <0.4 ppm pinonaldehyde, <2 ppm formic acid, and <1 ppm acetic acid were formed. These concentrations, as well as that of the unreacted (+)-α-pinene (51 ppm), were below established no effect levels. The mean reduction of the respiratory rate (30%) was significantly different (p≪0.001) from clean air, as well as from exposure of (+)-α-pinene, ozone, and formaldehyde themselves at the concentrations measured. Addition of the effects of the measured residual reactants and products cannot explain the observed sensory irritation effect. This suggests that one or more strong airway irritants have been formed. Therefore, oxidation reactions of common naturally occurring unsaturated compounds (e.g., terpenes) may be relevant for indoor air quality.     

Contribution ratio of freely to total dissolved concentrations of polycyclic aromatic hydrocarbons in natural river waters

The bioavailability and ecological risk of hydrophobic organic compounds (HOCs) in aquatic environments largely depends on their freely dissolved concentrations. In this work, the freely dissolved concentrations of polycyclic aromatic hydrocarbons (PAHs) including phenanthrene, pyrene, and chrysene were determined for the Yellow River, Haihe River and Yongding River of China using polyethylene devices (PEDs). The results indicated that the order of ratios of freely to total dissolved concentrations of the three PAHs was phenanthrene (66.8 ± 20.1%) > pyrene (48.8 ± 26.4%) > chrysene (5.5 ± 3.3%) for the three rivers. The ratios were significantly negatively correlated with the log K_ow values of the PAHs. In addition, the ratios were negatively correlated with the suspended sediment (SPS) and dissolved organic carbon (DOC) concentrations in the river water, and the characteristics of the SPS and DOC were also important factors. Simulation experiments showed that the ratio of freely to total dissolved concentrations of pyrene in the aqueous phase decreased with increasing SPS concentration; when the sediment concentration increased from 2 g L^?1 to 10 g L^?1, the ratio decreased from 67.6% to 38.4% for Yellow River sediment and decreased from 50.4% to 33.6% for Haihe River sediment. This was because with increasing SPS concentration, more and more DOC, small particles and colloids (<0.45 μm) would enter the aqueous phase. Because high SPS and DOC concentrations exist in many rivers, their effect on the freely dissolved concentrations of HOCs should be considered when conducting an ecological risk assessment.     

Influence of air mass trajectories on the chemical composition of precipitation in India

Chemical composition of precipitation was measured with wet-only samplers at a rural site at Bhubaneswar in eastern India during 1997–1998. All rain events were compared with trajectories and precipitation fields from the ECMWF. The pH and ionic concentrations were found to vary systematically with the origin of air and the amount of rainfall along the trajectory. A seasonal cycle for pH was found with a monthly median pH below 5.0 during October–December. The highest monthly median concentration of Ca²⁺ was found in May with 20 μmol l⁻¹ and for SO₄²⁻ in January with 52 μmol l⁻¹. Samples with trajectories within 400 km from Bhubaneswar during the last 5 days were found to have a median pH slightly below 5.0 as an average. These samples also had the highest concentration for all measured ions, indicating large pollution sources within the region. Samples with continental origin showed a decrease of ∼70% in concentration if there had been rain during >50% of the last 5 days compared to rain during <50% of the last 5 days. High concentrations of Na⁺ and Cl⁻ were also found in continental samples. Resuspension of previously deposited sea salt is believed to be the reason. The data were compared with data from three other sites in western India and higher concentrations of almost all ions (NH₄⁺ being the exception) compared to Bhubaneswar were found at the west coast in monsoon samples.     

Study of aluminium distribution and speciation in atmospheric particles of different diameters in Nanjing,China

Aluminium (Al) is one of the trace inorganic metals present in atmospheric particles. Al speciation study is essential to better evaluate the mobility, availability, and persistence of trace Al and Al species in the atmosphere. This paper reports Al distribution and speciation in atmospheric particles with aerodynamic diameters >10.0, 10.0–2.5 and <2.5 μm in the urban area of Nanjing, China. Urban particles were collected with a high-volume sampling system equipped with a cascade impactor, which effectively separates the particulate matter into three size ranges. Particulate Al was fractionated into five different forms (insoluble, oxide, organic, carbonate, and exchangeable species) by the modified five-step Tessier's sequential extraction procedure. The main points are as follows: (1) The average levels of Al in PM_2.5, PM_2.5–10 and PM_>10 are 2.02±0.35, 3.04±0.43 and 6.32±0.76 μg m⁻³, respectively, with PM_2.5, PM_2.5–10 and PM_>10 constituting respectively, 17.8±3.1%, 26.7±3.8% and 55.5±6.7% of suspended particulate matter (SPM) mass (11.38 μg m⁻³). (2) The vertical profile of airborne Al in the above three size fractions has been estimated. A significant increase in airborne Al concentrations was found for PM_2.5, PM_2.5–10 and PM_>10 as the sampling height above the ground increased from 2.5 to 17.5 m; however, there was an obvious decrease in airborne Al concentrations between 17.5 and 40.0 m. The maximum mean of total Al in PM_2.5, PM_2.5–10 and PM_>10 occurred between 12.5 and 20.0 m above the ground. (3) The distribution of Al speciation was studied. It was found that the size distribution of airborne Al species followed the order: insoluble species>oxide species>organic species>carbonate species>exchangeable species.     

Fate of caffeine in mesocosms wetland planted with Scirpus validus

Uptake, accumulation and translocation of caffeine by Scirpus validus grown in hydroponic condition were investigated. The plants were cultivated in Hoagland’s nutrient solution spiked with caffeine at concentrations of 0.5–2.0 mg L^?1. The effect of photodegradation on caffeine elimination was determined in dark controls and proved to be negligible. Removal of caffeine in mesocosms without plants showed however that biodegradation could account for about 15–19% of the caffeine lost from solutions after 3 and 7 d. Plant uptake played a significant role in caffeine elimination. Caffeine was detected in both roots and shoots of S. validus. Root concentrations of caffeine were 0.1–6.1 μg g^?1, while the concentrations for shoots were 6.4–13.7 μg g^?1. A significant (p < 0.05) positive correlation between the concentration in the root and the initial concentrations in the nutrient solution was observed. The bioaccumulation factors (BAFs) of caffeine for roots ranged from 0.2 to 3.1, while BAFs for shoots ranged from 3.2 to 16.9. Translocation from roots to shoots was the major pathway of shoot accumulation. The fraction of caffeine in the roots as a percentage of the total caffeine mass in solution was limited to 0.2–4.4% throughout the whole experiment, while shoot uptake percentage ranged from 12% to 25% for caffeine at the initial concentration of 2.0 mg L^?1 to 50–62% for caffeine at the initial concentration of 0.5 mg L^?1. However, a marked decrease in the concentration of caffeine in the shoots between d-14 and d-21 suggests that caffeine may have been catabolized in the plant tissues subsequent to plant uptake and translocation.