综合管廊燃气舱结构形式对燃气爆炸超压的影响*

为研究地下综合管廊燃气舱结构形式对燃气爆炸超压的影响,采用数值模拟的方法,改变燃气舱高度,通风分区长度和局部开口大小,分析不同情况下的燃气爆炸超压变化规律。结果表明:冲击波传播速度随燃气舱高度的增加而减小,随着高度的增加,超压峰值曲线由“驼峰状”逐渐变为两端高中间低的“盆形”,爆炸过程产生的最大超压与高度成反比关系。超压峰值在340 m处接近0 kPa,延长通风分区并不会增加超压峰值,可以在考虑防火的要求下根据实际情况适当延长通风分区的长度。局部开口的存在使得爆炸气流能够自由泄压,超压峰值与开口的大小成反比关系。     

障碍物对瓦斯爆炸冲击波影响研究

为研究障碍物对瓦斯爆炸冲击波传播规律的影响,利用水平管道式气体——粉尘爆炸实验装置,测试并分析障碍物数量、尺寸和壁面粗糙程度对瓦斯爆炸冲击波超压、冲击波传播规律的影响。结果表明:障碍物对瓦斯爆炸过程中冲击波传播规律具有重要影响。障碍物存在时,改变了爆炸冲击波的传播规律,提高了冲击波超压的最大峰值压力,且随着障碍物数量和尺寸的增加,这种激励作用越明显。随着壁面粗糙程度的增大,瓦斯爆炸冲击波超压明显增大。研究结果对井下巷道瓦斯爆炸冲击波的防治具有一定的指导意义。     

障碍物排列方式对海洋平台蒸气云爆炸的影响

为了了解障碍物排列方式对海洋平台蒸气云爆炸的影响,基于CFD方法建立蒸气云爆炸计算模型,选用国外MERGE项目的系列爆炸实验进行模型验证,提出用于衡量障碍物排列不均匀度的量化参数,针对海洋平台典型结构形式,分析障碍物排列方式对爆炸强度的影响。研究结果表明:蒸气云爆炸后果对于结构排列方式比较敏感,结构障碍物间隔均匀排列的形式造成的爆炸冲击作用最大;在爆炸发展初期阶段,障碍物阻塞程度对超压产生和发展影响更加显著。最后,基于研究结果,给出在海洋平台油气泄漏危险区将管线沿甲板非均匀排列布置等防控建议,为海洋平台蒸气云爆炸安全防控提供理论指导。     

开敞空间可燃气云爆炸冲击波超压及灾害动力响应研究评述

为了进一步梳理和分析开敞空间可燃云爆炸冲击波超压传播规律及灾害动力响应方面的各项研究成果,推进可燃气体爆炸安全防控,减少人员伤亡和经济损失。在分析现有研究的基础上,总结开敞空间可燃气云爆炸冲击波超压传播规律及灾害动力响应研究等方面存在的不足,提出开敞空间多元混合气体爆炸冲击波超压传播规律研究、多影响参数下可燃气云爆炸冲击波超压传播规律定量分析、基于可燃气云爆炸冲击波超压作用下的承载体动力响应等未来研究的关键技术问题。     

障碍物布置对气体爆炸压力场的影响效果研究

为研究可燃气体爆炸压力场受障碍物布置的影响情况,运用流体动力学软件AutoReaGas建立不同阻塞程度和不同结构（平面、立体）的障碍物爆炸模型,模拟分析不同布置情况对气体爆炸压力场的影响程度和规律。研究表明:改变障碍物的阻塞程度和结构（平面、立体）都会影响可燃气体的爆炸超压峰值。同种障碍物结构下,随着阻塞率的增加,气体爆炸压力的增加程度在一定范围内呈现出先增大后减小的变化情况;相同阻塞率下,立体障碍物对爆炸压力场产生的影响明显大于平面障碍物。研究立体障碍物与平面障碍物对加速燃烧的影响情况旨在为工业生产过程中的实际应用提供理论依据和基础,为防控气体爆炸灾害提供一定参考借鉴作用。     

多元可燃气体爆炸极限理论预测模型研究*

为准确掌握和预测多元可燃气体的爆炸极限,开展2种多元可燃气体爆炸极限的理论预测模型研究。第1种模型针对“多种可燃气体+多种惰性气体”在空气中或氧气中混合,基于求解可燃气体绝热火焰温度的总比热特性方法以及化学平衡反应中的贫燃料(富氧)反应,提出该多元可燃气体的爆炸下限预测模型;第2种模型针对“可燃气体+惰性气体+氧气”混合,基于热平衡方程及混合气体的各组分浓度、淬灭电势及燃烧潜热,提出该多元可燃气体的爆炸极限预测模型。结果表明:在预测多元可燃气体的爆炸极限时,第1种模型具有较广泛的应用性,且表现出较高的准确度;第2种模型具有使用简单的特点,且扩展了LCR（勒夏特列原理）的应用范围。     

LES – DFSD modelling of vented hydrogen explosions in a small-scale combustion chamber

Accidental explosions are a plausible danger to the chemical process industries. In the event of a gas explosion, any obstacles placed within the path of the flame generate turbulence, which accelerates the transient flame and raises explosion overpressure, posing a safety hazard. This paper presents numerical studies using an in-house computational fluid dynamics (CFD) model for lean premixed hydrogen/air flame propagations with an equivalence ratio of 0.7. A laboratory-scale combustion chamber is used with repeated solid obstacles. The transient compressible large eddy simulation (LES) modelling technique combined with a dynamic flame surface density (DFSD) combustion model is used to carry out the numerical simulations in three-dimensional space. The study presented uses eight different baffle configurations with two solid obstructions, which have area blockage ratios of 0.24 and 0.5. The flame speed, maximum rate of pressure-rise as well as peak overpressure magnitude and timing are presented and discussed. Numerical results are validated against available published experimental data. It is concluded that, increasing the solid obstacle area blockage ratio and the number of consecutive baffles results in a raised maximum rate of pressure rise, higher peak explosion overpressure and faster flame propagation. Future model development would require more experimental data, probably in a more congested configuration.     

有障碍物开敞空间可燃气云爆炸超压场的数值模拟

利用计算流体动力学软件AutoReaGas定量研究障碍物、障碍物阻塞比对开敞空间可燃气云爆炸超压场的影响以及爆燃超压随测点距离变化的分布规律。研究结果表明:当有障碍物存在时,爆炸峰值超压会显著增加,且峰值超压随着障碍物阻塞比的增加而增加。对于有障碍物条件下开敞空间的丙烷气云爆炸,无论是气云内部还是气云外部,随着距爆心距离的增加,峰值超压都有减小的趋势。     

Effects of premixed methane concentration on distribution of flame region and hazard effects in a tube and a tunnel gas explosion

Study of flame distribution laws and the hazard effects in a tunnel gas explosion accident is of great importance for safety issue. However, it has not yet been fully explored. The object of present work is mainly to study the effects of premixed gas concentration on the distribution law of the flame region and the hazard effects involving methane-air explosion in a tube and a tunnel based on experimental and numerical results. The experiments were conducted in a tube with one end closed and the other open. The tube was partially filled with premixed methane-air mixture with six different premixed methane concentrations. Major simulation works were performed in a full-scale tunnel with a length of 1000 m. The first 56 m of the tunnel were occupied by methane–air mixture. Results show that the flame region is always longer than the original gas region in any case. Concentration has significant effects on the flame region distribution and the explosion behaviors. In the tube, peak overpressures and maximum rates of overpressure rise (dp/dt)_max for mixtures with lower and higher concentrations are great lower than that for mixtures close to stoichiometric concentration. Due to the gas diffusion effect, not the stoichiometric mixture but the mixture with a slightly higher concentration of 11% gets the highest peak overpressure and the shock wave speed along the tube. In the full-scale tunnel, for fuel lean and stoichiometric mixture, the maximum peak combustion rates is achieved before arriving at the boundary of the original methane accumulation region, while for fuel rich mixture, the maximum value appears beyond the region. It is also found that the flame region for the case of stoichiometric mixture is the shortest as 72 m since the higher explosion intensity shortens the gas diffusion time. The case for concentration of 13% can reach up to a longest value of 128 m for longer diffusion time and the abundant fuel. The “serious injury and death” zone caused by shock wave may reach up to 3–8 times of the length of the original methane occupied region, which is the widest damage region.     

CO2-超细水雾对瓦斯/煤尘爆炸抑制特性研究

为了解CO2-超细水雾对瓦斯/煤尘爆炸抑制特性，用自行搭建的实验系统，从超压、火焰传播速度和火焰结构3个方面研究了CO2-超细水雾形成的气液两相介质对9.5%瓦斯/煤尘复合体系爆炸的抑爆效果、影响因素与原因。研究结果表明:随着CO2体积分数和超细水雾质量浓度的增加，爆炸火焰最大传播速度、爆炸超压峰值均出现明显下降，火焰到达泄爆口时间显著延迟；尤其当CO2体积分数达到14%与超细水雾的共同抑爆效果凸显，瓦斯/煤尘复合体系爆炸超压的“震荡平台”消失，同时火焰结构呈现“整体孔隙化”。所得结论为煤矿井下高效防爆抑爆技术进行了完善和增强。     

Experimental study on unconfined methane explosion: Explosion characteristics and overpressure prediction method

Explosion accidents have become the main threat for the high-efficiency use of cleaner gas energy sources, such as natural gas. During an explosion, obstacle causing flame acceleration is the main reason for the increase of the explosion overpressure, which still remains to be fully understood. In this research, field experiments were conducted in a 1 m³ cubic frame apparatus to investigate the effect of built-in obstacles on unconfined methane explosion. Cage-like obstacles were constructed using square steel rods with different cross section size. The results demonstrated that the flame could get accelerated due to the hydrodynamic instability and obstacle-induced turbulence, which enhanced the explosion overpressure. In the near field, the overpressure wave travelled slower and the maximum overpressure could almost keep constant. Reducing the cross section size, or increasing the obstacle height or the obstacle number per layer could determine the rise of the maximum overpressure, the maximum pressure rising rate and the overpressure impulse. For uniformly constructed obstacles, self-similar theory was chosen to measure the influence of the hydrodynamic instability, and a parameter β was adopted to measure the flame acceleration caused by obstacle-induced turbulence, the value of which was 2 in this research. Based on the acoustic theory, an overpressure prediction model was proposed and the predicted results agreed with the measured values better than previous models, such as TNT equivalency model and TNO multi-energy model.     

输气管道高后果区蒸气云爆炸超压预测方法探究

为准确预测输气管道高后果区在发生蒸气云爆炸事故时的超压分布情况,对国内外运用较为广泛的蒸气云爆炸超压预测经验模型和数值模拟方法进行调研,并分别应用其对某输气管道全尺寸泄漏燃爆实验进行超压预测,结合实验数据和输气管道高后果区管理现状进行方法准确性和工程适用性分析。研究结果表明：基于等效TNT假设的Henrych模型、Mills模型和等效TNT当量数值模拟方法均不适合准确预测蒸气云爆炸超压,TNO多能法和混合气体数值模拟方法所预测的结果较为接近实验结果。TNO多能法使用简便且推广性强,但主观性较大,易高估或低估爆炸后果;混合气体数值模拟方法操作繁琐且推广性差,但分析结果精度较高。在对高后果区进行安全管控时,可结合TNO多能法与混合气体数值模拟方法同时对管道工况进行评估,确定TNO多能法的爆源强度等级,继而推广使用TNO多能法。该研究结果可在较大程度上保证评估的准确性并节约成本。     

Effect of separation distance on gas dispersion and vapor cloud explosion in a storage tank farm determined using computational fluid dynamics

Storage tank separation distance, which considerably affects forestalling and mitigating accident consequences, is principally determined by thermal radiation modeling and meeting industry safety requirements. However, little is known about the influence of separation distance on gas dispersion or gas explosion, which are the most destructive types of accidents in industrial settings. This study evaluated the effect of separation distance on gas dispersion and vapor cloud explosion in a storage tank farm. Experiments were conducted using Flame Acceleration Simulator, an advanced computational fluid dynamics software program. Codes governing the design of separation distances in China and the United States were compared. A series of geometrical models of storage tanks with various separation distances were established. Overall, increasing separation distance led to a substantial reduction in vapor cloud volume and size in most cases. Notably, a 1.0 storage diameter separation distance appeared to be optimal. In terms of vapor cloud explosion, a greater separation distance had a marked effect on mitigating overpressure in gas explosions. Therefore, separation distance merited consideration in the design of storage tanks to prevent gas dispersion and explosion.     

基于FLACS的海上钻探平台井喷爆炸事故后果模拟分析*

为研究海上钻探平台井喷燃爆事故后果,运用FLACS软件对某深海钻探平台井喷爆炸事故进行模拟,研究在不同事故场景下气云爆炸发展过程及平台荷载分布规律,讨论井喷速率、风向、点火位置等对爆炸超压的影响。研究结果表明:随泄漏速率增加,爆炸强度和爆炸范围均增大,爆炸严重程度不仅与井喷速率密切相关,同时也受平台结构影响;点火位置会对爆炸超压产生影响,在可燃气体与空气混合气体比例为化学理论当量比处点燃气体,生活区承受的爆炸超压最大;在设施及建构筑物分布较为密集、拥塞度较高的地方产生的爆炸超压更大。研究结果可为可为平台的阻隔防爆性能设计与应急响应提供指导。     

大尺度障碍物与泄爆面对天然气内爆炸的协同作用规律研究

为阐释民用建筑内部大尺度物品与门窗等泄爆面对天然气爆炸灾害的协同作用机制，基于典型厨房空间布局及内部物品特征，借助计算流体动力学技术研究了不同泄爆面开启压力和不同大尺度障碍物体积阻塞率条件下天然气内爆炸火焰速度、爆炸超压的分布规律。研究结果表明:大尺度障碍物与泄爆面对室内天然气爆炸过程具有显著的协同作用，共同促进火焰速度与爆炸超压的显著增长，并缩短峰值超压到达时间；大尺度障碍物的存在虽然显著降低了室内天然气的体积，但从增加房间内湍流源和相对长径比的角度进一步促进了泄爆效应；大尺度障碍物与泄爆面协同作用下，室内火焰速度呈现明显的阶段性特征，并在泄爆面附近发生波动。研究结论可为民用建筑物内气体爆炸事故调查分析和灾害评估提供科学依据。     

空间阻塞对室内燃气泄漏爆炸影响研究

以餐饮企业的熟食操作间为例建立物理模型,通过CFD方法模拟不同空间阻塞度下天然气泄漏爆炸情形。研究结果表明:阻塞率在99.95%~100%时,燃气浓度呈现反抛物线式上升。空间阻塞率在99.982%时（开敞面积1 m2）,泄漏1 200 s,熟食操作间燃气浓度值可达6%;空间阻塞率在99.955%（开敞面积2.5 m2）~100%时,燃气爆炸后熟食操作间内产生的超压最大值均大于30 kPa;当空间阻塞率在99.991%（开敞面积0.5 m2）~100%时,设定工况下爆炸超压随空间阻塞率呈指数式增加。研究认为,空间阻塞率在99.95%以上,燃气泄漏极易形成可燃蒸汽云,发生爆炸产生冲击波超压能够毁坏建筑物,在生产和生活中,对于有燃气使用的空间,应尽可能降低空间阻塞率,以避免可能的燃气泄漏形成危险域和爆炸形成过高冲击波超压。     

Experimental study on the feasibility of explosion suppression by vacuum chambers

In view of the invalidity of suppression and isolation apparatus for gas explosion, a closed vacuum chamber structure for explosion suppression with a fragile plane was designed on the base of the suction of vacuum. Using methane as combustible gas, a series of experiments on gas explosion were carried out to check the feasibility of the vacuum chamber suppressing explosion by changing methane concentration and geometric structure of the vacuum chamber. When the vacuum chamber was not connected to the tunnel, detonation would happen in the tunnel at methane volume fraction from 9.3% to 11.5%, with flame propagation velocity exceeding 2000 m/s, maximum peak value overpressure reaching 0.7 MPa, and specific impulse of shock wave running up to 20 kPa s. When the vacuum chamber with 5/34 of the tunnel volume was connected to the flank of the tunnel, gas explosion of the same concentration would greatly weaken with flame propagation velocity declining to about 200 m/s, the quenching distance decreasing to 3/4 of the tunnel length, maximum peak value overpressure running down to 0.1-0.15 MPa and specific impulse of shock wave below 0.9 kPa s. The closer the position accessed to the ignition end, the greater explosion intensity weakened. There was no significant difference between larger section and smaller vacuum chambers in degree of maximum peak value overpressure and specific impulse declining, except that quenching fire effect of the former was superior to the latter. The distance of fire quenching could be improved by increasing the number of the vacuum chambers.     

典型三床RTO设备燃爆危险性数值模拟研究*

为研究苯、甲苯、二甲苯混合废气在三床蓄热式废气焚烧炉内部的燃烧过程,基于FLUENT软件建立典型的三床蓄热式废气焚烧炉的物理模型和数值模型,重点分析进气风量和混合可燃气体-空气摩尔占比对其内部压力变化规律的影响,以期可为其安全设计提供借鉴。研究结果表明:燃烧室内的温度变化与燃烧速度变化保持一致,可通过监测RTO燃烧室内的温度来定性评估气体燃烧速度,随着进气风量的增加,混合废气燃烧速度先升高后下降后再升高;从能源损耗和安全生产2个方面综合考虑,得出RTO运行的最佳进气风量为15 000 m3/h到30 000 m3/h,最佳的混合可燃气体-空气摩尔占比为0.15~0.2,这与RTO实际工况相符合,解释RTO装置内废气积聚导致爆炸事故的原因,燃烧过程中压力出现2次峰值超压,实际生产中需在2个时间节点多加防范。     

综合管廊燃气舱燃气爆炸冲击波传播特征研究*

为研究综合管廊燃气舱燃气爆炸冲击波的传播特征,采用数值模拟方法研究首次超压峰值和首次流速峰值的变化规律,建立首次流速峰值与首次超压峰值和填充长度的耦合关系,分析不同填充长度情况下燃气爆炸后的超压和水平流速的变化规律。结果表明:燃气爆炸后,燃气舱内存在多个超压峰值,峰值间存在明显的时间差。冲击波到达各测点的时间与燃气填充长度成反比关系。水平流速曲线随着时间的变化以0为基点上下振荡,存在正向峰值和反向峰值。随着燃气填充长度的增加,流速下降趋势变快。首次超压峰值随传播距离的增加先增大后减小再增大,随着填充长度的增加,产生超压峰值最大值的位置由接近填充长度结束的位置转移到燃气舱封闭端。首次流速峰值随传播距离的增加先增大后减小。首次流速峰值与首次超压峰值呈现正比关系,通过拟合得到流速峰值与超压峰值及填充长度的耦合关系。研究结果可为燃气舱燃气爆炸后的流速分布研究以及燃气舱防火分区的设计提供参考。     

障碍物对油气-空气混合气体泄压爆炸火焰传播特性影响

为了研究障碍物对油气泄压爆炸火焰传播特性的影响规律,进行了不同数量障碍物工况下的对比实验,并利用纹影仪和高速摄影仪记录了火焰传播过程,针对障碍物对火焰形态、火焰锋面位置及火焰传播速度的影响规律进行了研究,结果表明:圆柱体障碍物会导致油气泄压爆炸火焰形态产生褶皱和弯曲变形,诱导层流火焰向湍流火焰转变,加速火焰的传播,对油气泄压爆炸火焰的初始传播形态有显著影响;随着障碍物数量的增多,火焰锋面传播距离点火端的最大距离增大,但到达最远距离的时间减少;障碍物能够增强火焰的传播速度,尤其对障碍物下游火焰影响最为显著,随着障碍物数量的增多,火焰传播的最大速度也随之增大,但达到最大火焰传播速度的时间却随之减少;障碍物的存在增大了油气泄压爆炸过程外部爆炸压力,并且随着障碍物数量的增多,外部爆炸压力峰值增长幅度增大。