放射性浓缩液桶内干燥过程数学模型及动态仿真

为实现放射性浓缩液最大程度减容,设计了桶内干燥系统,基于物料衡算与热量衡算,建立了干燥过程动态数学模型,考察了不同的工艺条件对系统总体运行参数的影响,预测了桶内物料质量、含盐率、理论料面高度、温度、蒸发速率等关键参数随时间的变化规律。结果表明:干燥总时长随加热功率、浓缩液含盐率、浓缩液温度、最终干燥盐分湿含率以及第一阶段单次加料体积的增大而减小;干燥初期,新物料的加入对桶内含盐率有较为显著的降低作用;提高干燥强度将降低料面高度,间接降低热能有效利用率;在典型的工艺条件下,桶内干燥系统理论干燥总时长为281.19h,平均蒸发速率为3.43kg/h,平均处理能力为4.05L/h。为桶内干燥系统设计及试验提供理论指导。     

POTENTIAL,ACTUAL, AND EQUILIBRIUM EVAPOTRANSPIRATION IN A WHEAT FIELD 1

ABSTRACT: This paper examines the relationship between both potential (E*) and nonpotential evapotranspiration and equilibrium evapotranspiration (EQ) in an irrigated wheat field in southcentral Alberta, Canada. The control exercised by surface wetness and root reservoir moisture content in determining the value of the Priestley-Taylor constant a is explored. Also investigated is the relationship between a and the vapor flux fraction ET/(R-G) where ET is the actual evapotranspiration, R the net radiation, and G the soil heat flux. It is shown that evapotranspiration occurred at the potential rate (E*) when the available soil moisture (ASM) within the root zone was ≥3 percent. a varied from 0.84 for a dry soil to 1.49 for a saturated soil. The mean a for E* was 1.24. Surface wetness sustained evapotranspiration at the potential rate when such wetting exceeded 2mm d^?1 following a period of prolonged drawdown of soil moisture, α and ET/(R-G) were positively correlated and this correlation strengthened with increasing soil moisture for constant values of the energy partitioning factor s+γ/s where s is the slope of the saturation humidity-temperature curve and γ is the psychrometric constant. ET=EQ when ETI(R-G) lay within the range of 0.59 to 0.82 corresponding to Bowen ratio (β) values of 0.22 and 0.69, respectively.     

EVAPOTRANSPIRATION AND CANOPY RESISTANCE AT AN UNDEVELOPED PRAIRIE IN A HUMID SUBTROPICAL CLIMATE1

ABSTRACT: Reliable estimates of evapotranspiration from areas of wildland vegetation are needed for many types of water-resource investigations. However, little is known about surface fluxes from many areally important vegetation types, and relatively few comparisons have been made to examine how well evapotranspiration models can predict evapotranspiration for soil-, climate-, or vegetation-types that differ from those under which the models have been calibrated. In this investigation at a prairie site in west-central Florida, latent heat flux (λE) computed from the energy balance and alternatively by eddy covariance during a 15-month period differed by 4 percent and 7 percent on hourly and daily time scales, respectively. Annual evapotranspiration computed from the energy balance and by eddy covariance were 978 and 944 mm, respectively. An hourly Penman-Monteith (PM) evapotranspiration model with stomatal control predicated on water-vapor-pressure deficit at canopy level, incoming solar radiation intensity, and soil water deficit was developed and calibrated using surface fluxes from eddy covariance. Model-predicted λE agreed closely with λE computed from the energy balance except when moisture from dew or precipitation covered vegetation surfaces. Finally, an hourly PM model developed for an Amazonian pasture predicted λE for the Florida prairie with unexpected reliability. Additional comparisons of PM-type models that have been developed for differing types of short vegetation could aid in assessing interchangeability of such models.     

ESTIMATION OF REGIONAL EVAPOTRANSPIRATION FROM ARID AND SEMI-ARID SURFACES1

ABSTRACT: Evapotranspiration (ET) from oasis and Gobi surfaces in the Heihe River region of China was estimated by Kotoda (1986) and Advection-Aridity (Brutsaert and Stricker, 1979) models. The ET estimates were compared with eddy-correlation ET estimates. The ET estimated by both models are in good agreement with ET obtained by means of eddy-correlation method for the oasis surface while underestimating ET as compared to the eddy-correlation method. For the Gobi surface, the models yielded obviously overestimates of evapotranspiration. In order to estimate evapotranspiration from arid surfaces, the Kotoda model was modified by introducing the surface moisture availability parameter a from Barton (1979). The modified Kotoda model yielded ET estimates that were very close to that from the eddy-correlation method for the Gobi surface. The modified Kotoda model was used to estimate evapotranspiration from the Heihe River watershed, an area with complicated topography and land use, and the results compared with those from a water balance method. A sensitivity analysis of the modified model was performed. The results show that the modified Kotoda model can reflect the relationship between the actual evapotranspiration and the main controlling factors on it for both wet and arid surfaces reasonably. From this study, it can be concluded that the modified Kotoda model is applicable fro the estimation of regional evapotranspiration from areas with complicated topography and land use.     

EVAPOTRANSPIRATION MEASUREMENT AND ESTIMATION OF THREE WETLAND ENVIRONMENTS IN THE UPPER ST. JOHNS RIVER BASIN,FLORIDA1

ABSTRACT: Accurate estimates of evapotranspiration from areas dominated by wetland vegetation are needed in the water budget of the Upper St. Johns River Basin. However, local data on evapotranspiration rates, especially in wetland environments, were lacking in the project area. In response to this need, the St. Johns River Water Management District collected evapotranspiration field data in Fort Drum Marsh Conservation Area over the period 1996 through 1999. Three large lysimeters were installed to measure the evapotranspiration from different wetland environments: sawgrass (Cladium jamaicense), cattail (Typha domingensis), and open water. In addition, pan evaporation was measured with a standard class “A” pan. Concurrently, meteorological data including rainfall, solar radiation, wind speed, relative humidity, air temperature, and atmospheric pressure were collected. By comparing computed evapotranspiration rates with those measured in the lysimeters, parameters in the Penman‐Monteith, the Priestley‐Taylor, and Reference‐ET methods, and evaporation pan coefficients were estimated for monthly and seasonal cycles. The results from the data collected in this study show that mean monthly evapotranspiration rates, computed by the different methods, are relatively close. From a practical point of view, results indicate that the evaporation pan can be used equally well as the more complex and data‐intensive methods. This paper presents the measured evapotranspiration rates, evaporation pan coefficients, and the estimated parameter values for three different methods to compute evapotranspiration in the project area. Since local data on evaporation are often scarce or lacking, this information may be useful to watershed hydrologists for practical application in other project regions.     

ESTIMATING AVERAGE MONTHLY LAKE EVAPORATION IN THE NORTHEAST UNITED STATES1

ABSTRACT: A methodology to estimate the average monthly lake evaporation, E(τ), (month τ=1,12) for fresh water bodies located in the northeast United States is presented. The approach combines analysis of at‐site, lake‐specific vertical water temperature profile data and a previously developed regional air temperature based model approximation of the widely accepted modified Penman energy budget estimate of mean monthly potential evaporation, E_p(τ) (mm/day). The paper presents procedures to develop site‐specific estimates of E_p(τ) and to convert water temperature data to average monthly conductive heat flux, G(τ). With monthly estimates of G(τ), the average monthly potential evaporation, E_p(τ), is then convertible to estimates of the average monthly lake evaporation, E(τ). This new method permits a good estimate of site‐specific lake evaporation rates without the data and computational requirements of the Penman energy budget procedure nor the comparatively expensive, time consuming field eddy correlation approach.     

ESTIMATING EVAPORATION FROM UTAH'S GREAT SALT LAKE USING THERMAL INFRARED SATELLITE IMAGERY1

ABSTRACT: Water surface temperatures can be obtained from satellite thermal remote sensing. Landsat and other satellites sense emitted thermal infrared radiation on a regular basis over much of the earth's surface. Evaporation is accomplished by the net transport of mass from the water surface to the atmosphere. The evaporative transfer predominantly determines the water surface temperature. Hence, there should be good correlations between evaporation and surface temperatures. Previous investigations on Utah Lake with satellite-derived temperatures and pan- and model-derived evaporation values have produced good correlations. However, more study was required with additional satellite data and evaporation measurements for saltwater conditions. The applicability of this method for estimating evaporation on Utah's Great Salt Lake was of particular interest at this time because of the unprecedented rise of this terminal lake. Satellite thermal data and evaporation data from four different years were obtained for the Great Salt Lake and the surrounding region. More than 350 correlation and linear regression analyses were performed on the temperature and evaporation data. The lake salt concentrations were also factored into the analyses in several different ways. The correlation results were generally very good and a methodology for using satellite-derived water surface temperatures along with salt concentrations was developed to estimate evaporation.     

SELECTION OF APPROPRIATE EVAPORATION ESTIMATION TECHNIQUE FOR CONTINUOUS MODELING1

ABSTRACT: The importance of evaporation in hydrologic modeling has been investigated by analysis of water budget at various scales and application of a water management model at plot scale. The data at all scales indicate that evaporation constitutes a major hydrological output. Accurate determination of watershed evapotranspiration depends upon appropriate accounting for the various components of evapotranspiration and their areal and temporal variability. An application of a water management model has revealed that the ranking of the sensitivity of input parameters depends upon the method of determination of evapotranspiration.     

Automated Calibration of the METRIC‐Landsat Evapotranspiration Process

A remaining challenge to applying satellite‐based energy‐balance algorithms for operational estimation of evapotranspiration (ET) is the calibration of the energy‐balance model. Customized calibration for each image date is generally required to overcome biases associated with radiometric accuracy of the image, uncertainties in aerodynamic features of the landscape, background thermal conditions, and model assumptions. The CIMEC process (calibration using inverse modeling at extreme conditions) is an endpoint calibration procedure where near extreme conditions in the image are identified where the ET can be estimated and assigned. In the Mapping EvapoTranspiration at high Resolution with Internalized Calibration (METRIC?) energy‐balance model, two endpoints represent the dry and wet ends of the ET spectrum. Generally, user‐intervention is required to select locations in the image to produce best accuracy. To bring the METRIC and similar processes into the domain of less experienced operators, a consistent, reproducible, and dependable statistics‐based procedure is introduced where relationships between vegetation amount and surface temperature are used to identify a subpopulation of locations (pixels) in an image that may best represent the calibration endpoints. This article describes the background and logic for the statistical approach, how the statistics were developed, area of interest requirements and assumptions, adjustment for dry conditions in desert climates, and implementation in a common image processing environment (ERDAS Imagine).     

THE APPLICABILITY OF MORTON'S AND PENMAN'S EVAPOTRANSPIRATION ESTIMATES IN RAINFALL-RUNOFF MODELING1

ABSTRACT: Estimates of the upper constraint on actual evapotranspiration are required as input data in the majority of rainfall-runoff models. This paper compares and discusses the applicability of Penman's potential evapotranspiration estimates and Morton's wet environment evapotranspiration estimates in rainfall-runoff modeling applications. Morton's wet environment evapotranspiration depends only on the atmospheric variables and is the estimate of evapotranspiration that would occur when water supply is not limiting. It is a conceptually more correct representation of the upper constraint on actual evapotranspiration compared to Penman's potential evapotranspiration which is dependent on the water supply to the soil-plant surfaces. Although Penman's potential evapotranspiration and Morton's wet environment evapotranspiration are two different quantities, comparison of the two estimates using data from different climatic regions throughout Australia indicate that they provide similar magnitudes of the upper limit of actual evapotranspiration at moderate climatic conditions when reliable estimates are required in rainfall-runoff models. The two estimates can therefore be used interchangeably in rainfall-runoff modeling applications.     

Using nighttime light data to estimate water evaporation inside buildings in China's urban areas

Urbanization has a great impact on urban evapotranspiration. Water evaporation inside buildings is an important part of urban water vapor resources and a crucial core of urban hydrological processes. The systematic studies on building water evaporation (BWE) are mostly the method of experimental monitoring. This study proposed a new method to simulate and estimate water evaporation flux inside buildings in urban areas. Based on the nighttime light data and urban per capita gross domestic product (GDP), a new modeling system was built to simulate the total BWE. Building area was calculated using the nighttime light data. And the BWE coefficient D_f was estimated according to the important indicator of economic development per capita GDP value. Then the water evaporation inside urban buildings and the spatial distribution of water evaporation inside buildings in typical cities could be obtained. The results showed that the total amount of water evaporation inside buildings in China's urban areas was 24.5 billion m³. Among the 31 provincial capitals in China, Shanghai had the largest BWE of 1.08 billion m³. The minimum water evaporation of buildings in Lhasa was 20.0 million m³. Studies of BWE can assess urban water budgets, support on-demand allocation of water resources, and provide a fundamental understanding of the relationship between water resources and energy heat island effects in urban areas.     

低温试验系统中露点温度控制的节能技术

本文通过对低温系统露点温度控制技术的分析,指出该控制模式存在的不足,提出采用露点模式和时间程序模式相结合的露点节能控制模式对空气的干燥度和使用工况进行监控,从而实现对低湿度干燥空气的露点温度的智能监控.同时对两种控制模式耗能进行比较,指出露点节能控制模式明显优于单纯的时间程序控制模式,为低温系统露点控制提供了新的测控手段.     

DEFINING WATERSHED-SCALE EVAPORATION USING A NORMALIZED DIFFERENCE VEGETATION INDEX1

Monthly composites of the Normalized Difference Vegetation Indices (NDVI), derived from the National Oceanic and Atmospheric Administration's (NOAA) Advanced Very High Resolution Radiometer (AVILRR), were transformed linearly into monthly evaporation rates and compared with detailed hydrologic-model simulation results for five watersheds across the United States. Model-simulated monthly evaporation values showed high correlations (mean R²= .77) with NDVI-derived evaporation estimates. These latter estimates, used in a classical water balance model, resulted in equally accurate simulations of monthly runoff than when the model was run to estimate monthly evaporation via soil moisture accounting. Comparison of NDVI-derived evaporation estimates with pan data showed promise for transforming NDVI values into evaporation estimates under both wet and water-limiting conditions without resorting to the application of any kind of calibrated hydrologic models.     

SIMULATED RELATIONSHIPS BETWEEN SPECTRAL REFLECTANCE,THERMAL EMISSIONS,AND EVAPOTRANSPIRATION OF A SOYBEAN CANOPY1

ABSTRACT: A canopy reflectance model is incorporated into a routine for simulating water and energy flows in the soil-plant-atmosphere system. The reflectance model is structured tocalculate canopy albedo throughout each simulation period and to determine spectral reflectances at a specified time during the day. Spectral vegetation indices are then calculated from the reflectances and related to the evapotranspiration and thermal response of the canopy. The canopy reflectance model is also used to establish the photo-sytheticaily active radiation load at various depths in the canopy. Stomatal resistances are calculated using these radiation values and integrated to give the minimum canopy resistance. Actual canopy resistance is obtained by adjusting minimum canopy resistance for environmental stresses such as leaf water potential and leaf temperature. Using data for a soybean canopy, canopy evapotranspiration and temperatures are simulated for a range of leaf area index values and compared with the corresponding spectral vegetation indices. The resuits indicate that the normalized difference spectral index has an inverse linear relationship with canopy temperature, concurring with results obtained from satellite observations. The possibility of using a spectral vegetation index and thermal observations together to parameterize surface moisture availability for evapotranspiration is considered.     

On the Relationship Between Mean and Variance of Soil Moisture Fields1

Abstract: The objective of this work was to explain an apparent contradiction in the literature related to the relationship between mean and variance (or standard deviation) of soil moisture fields. Some studies found an increase in soil moisture variance with decreasing mean soil moisture, while others showed a decrease. The evidence of maximum variance in the mid‐range of mean soil moisture was also reported in the literature. In this paper, we focus on the effects of spatial variability of soil texture on the relationship between variance and mean of soil moisture during soil dry‐down processes. Soil texture influences soil moisture mean and variance through its direct effects on evaporation and drainage, which are two main factors controlling soil drying. A differential equation describing soil moisture dry down is proposed and studied. Our study shows that as mean soil moisture is greater than a threshold, variance increases with decreasing mean soil moisture. If mean soil moisture is less than the threshold, variance decreases with decreasing mean soil moisture. The threshold depends on soil texture and is between the field capacity and the wilting point. The soil moisture dry‐down equation is also applied to explain the apparent contradiction with regard to the relationship between mean and variance of soil moisture fields reported in the literature.     

Evaluating the impact of green roof evapotranspiration on annual building energy performance

The performance of the building envelope predominantly determines the ultimate energy performance throughout the lifecycle of a building. A sustainable alternative to enhance roof performance while limiting heat flux through a roof is integrating passive techniques such as green roof. Particularly, green roof performance is sensitive to local climate. The main objective of this study was to evaluate the evapotranspiration effect of an extensive green roof on annual energy consumption of an office building in relation to the humid continental climate of Republic of Korea. The dynamic behavior of green roof and building energy performance were investigated through a parametric simulation method using green roof module in EnergyPlus coupled with jEPlus. Structural data of the reference building and ASHARE 90.1-2007 operational schedules were used as inputs for baseline building model while inputs for the green roof module were based on experimental data sets. Due to the influence of the humid conditions and local wind current on the evapotranspiration process, it was generally found that high leaf area index (LAI) reduced cooling energy demand and somewhat reduced heating energy demand as well; corresponding to the highest daily evapotranspiration fluxes of 4.79 mm day^?1 in summer and 1.80 mm day^?1 in winter. Increasing LAI from 20% to 100% cover increased evapotranspiration flux by 10.4% in summer and 80.2% in winter. Thus to minimize energy losses in winter, foliage cover must be carefully considered. Within limitations specified, the overall annual building energy consumption deceased by 90.9 GJ (3.7%).     

MODELING THE BUILDUP AND WASHOFF OF POLLUTANTS ON URBAN WATERSHEDS1

ABSTRACT: A model for urban stormwater quality was developed in this study. The basis for the model is the process by which pollutants build up on the watershed surface. For the wet climate of the study site, it was assumed that there exists an interval of time over which the pollutant buildup equals the pollutant washoff (no accumulation of pollutant). The buildup model was represented by a linear function of the antecedent dry time. The buildup function was then linked with a pollutant washoff model represented by a power function of the storm runoff volume. Various time intervals for no net accumulation were tested to calibrate the model. The model was calibrated to observed data for two small urban basins in Baton Rouge, Louisiana, and model results were used to analyze the behavior of phosphorus concentrations in storm runoff from these basins over a long period of time.     

Differences in Evaporation Between a Floating Pan and Class A Pan on Land1

Abstract: Research was conducted to develop a method for obtaining floating pan evaporation rates in a small (less than 10,000 m²) wetland, lagoon, or pond. Floating pan and land pan evaporation data were collected from March 1 to August 31, 2005, at a small natural wetland located in the alluvium of the Canadian River near Norman, Oklahoma, at the U.S. Geological Survey Norman Landfill Toxic Substances Hydrology Research Site. Floating pan evaporation rates were compared with evaporation rates from a nearby standard Class A evaporation pan on land. Floating pan evaporation rates were significantly less than land pan evaporation rates for the entire period and on a monthly basis. Results indicated that the use of a floating evaporation pan in a small free‐water surface better simulates actual physical conditions on the water surface that control evaporation. Floating pan to land pan ratios were 0.82 for March, 0.87 for April, 0.85 for May, 0.85 for June, 0.79 for July, and 0.69 for August.     

SOIL WATER CHARACTERISTICS OF TWO SOIL CATENAS IN ILLINOIS: IMPLICATIONS FOR IRRIGATION1

ABSTRACT: Soil water was monitored by neutron scattering in six soils, three each within two drainage catenas in east-central Illinois, over a 15-month time span. The prairie soils have formed in: (1) 76–152 cm of silt loam, eolian sediments (bess) over glacial till (Catlin-Flanagan-Drummer catena), and (2) bess greater than 152 cm in thickness (Tama-Ipava-Sable catena). We characterized the water content of these soils over the total time span and for wet and dry climatic subsets, as an aid to potential irrigation decisions. Soils of the thin bess, C-F-D catena dried out to lower water contents and had greater soil water variability than did the thick bess soils. Under wet conditions, soil water contents in the two catenas were quite similar. Alleviation of surface and subsurface drying via irrigation would thus be more advantageous to yields on the C-F-D soils than on the T-I-S soils.     

A CONCEPTUAL FRAMEWORK FOR EVALUATING AGRICULTURAL WATER CONSERVATION POTENTIALS1

ABSTRACT: This paper defines types of water losses in irrigated agriculture and outlines potentials for water conservation. Recoverable water “losses” (seepage, leakage, and spillage during storage and conveyance, and surface runoff and deep percolation during irrigation) and irrecoverable losses (evaporation from water and soil surfaces and transpiration from plants) are described and illustrated. Some conservation terms are defined, particularly the distinction between on-farm irrigation efficiency and areawide efficiency. Briefly reviewed are agricultural water conservation technologies and their applicability. The biggest untapped potential for water conservation may be a reduction in irrecoverable losses, especially evapotranspiration. The advantages and disadvantages of reducing recoverable and irrecoverable water losses are described, including possible effects on ground water, energy, salinity, crops, wildlife, and in-stream uses. Such information may be useful in several policy and management issues, e.g., ground water overdraft and possible constraints on crops and sites to be irrigated.