BUILDUP,WASHOFF, AND EVENT MEAN CONCENTRATIONS1

ABSTRACT: Most watershed water quality simulation models require the user to specify pollutant buildup and washoff rate parameters for pollutants, by land use. Buildup and washoff rates are difficult to measure directly, and only limited guidance and few observed data are available from the literature. Many studies, however, report storm event mean concentrations (EMCs). These EMCs must arise as a result of the buildup and washoff processes, but typically represent the net contribution from a variety of pervious and impervious surfaces. This paper explores the relationship between EMCs and buildup/washoff parameters. An assumption of the mathematical form of the buildup/washoff relationship gives an algebraic expression for the EMC consistent with model assumptions. This yields techniques to separate observed EMCs into contributions from different land uses and from pervious and impervious surfaces. Given this relationship, numerical optimization may be used to estimate site specific values of buildup and washoff parameters from observed storm EMCs for use in modeling. Use of this approach helps ensure that model parameters are consistent with observed data, providing a rational starting point for final model calibration. Several site examples demonstrate use of the method.     

ALAWAT: A spatially allocated watershed model for approximating stream,sediment, and pollutant flows in Hawaii,USA

The Ala Wai Canal Watershed Model (ALAWAT) is a planning-level watershed model for approximating direct runoff, streamflow, sediment loads, and loads for up to five pollutants. ALAWAT uses raster GIS data layers including land use, SCS soil hydrologic groups, annual rainfall, and subwatershed delineations as direct model parameter inputs and can use daily total rainfall from up to ten rain gauges and streamflow from up to ten stream gauges. ALAWAT uses a daily time step and can simulate flows for up to ten-year periods and for up to 50 subwatersheds. Pollutant loads are approximated using a user-defined combination of rating curve relationships, mean event concentrations, and loading/washoff parameters for specific subwatersheds, land uses, and times of year. Using ALAWAT, annual average streamflow and baseflow relationships and urban suspended sediment loads were approximated for the Ala Wai Canal watershed (about 10,400 acres) on the island of Oahu, Hawaii. Annual average urban suspended sediments were approximated using two methods: mean event concentrations and pollutant loading and washoff. Parameters for the pollutant loading and washoff method were then modified to simulate the effect of various street sweeping intervals on sediment loads.     

POLLUTANT LOADS IN URBAN STORMWATER: REVIEW OF METHODS FOR PLANNING-LEVEL ESTIMATES1

ABSTRACT: A review of methods for planning-level estimates of pollutant loads in urban stormwater focuses on transfer of charac. teristic runoff quality data to unmonitored sites, runoff monitoring, and simulation models. Load estimation by transfer of runoff quality data is the least expensive, but the accuracy of estimates is unknown. Runoff monitoring methods provide best estimates of existing loads, but cannot be used to predict load changes resulting from runoff controls, or other changes of the urban system. Simulation models require extensive calibration for reliable application. Models with optional formulations of pollutant build up, washoff, and transport can be better calibrated and the selection of options should be based on a statistical analysis of calibration data. Calibrated simulation models can be used for evaluation of control alternatives.     

A MODELING APPROACH FOR STORM WATER QUANTITY AND QUALITY CONTROL VIA DETENTION BASINS1

ABSTRACT: Storm water detention basins have historically been employed for quantity (i.e., flooding) control only. However, recently it has been suggested that these basins may also provide a practical means of storm water quality control. This paper presents the formulation of a mathematical modeling approach which may be used by professionals to simultaneously design detention basins for the dual purpose of storm water quantity and quality control. Model simulations demonstrate that for a given basin, pollutant removal increases as storm frequency increases. The importance of particle size distribution and settling velocity for net pollutant removal is illustrated, The design procedure is demonstrated, and pollutant loading diagrams for estimating pollutant removal as a function of storm size are developed.     

ACCUMULATION OF AS,NI, CU,AND PB IN RETENTION AND RECHARGE BASINS SOILS FROM URBAN RUNOFF1

ABSTRACT: The accumulation of arsenic, nickel, copper, and lead in the soil profile was determined beneath five urban storm-water retention/recharge basins used by the Fresno Metropolitan Flood Control District, California. Soils were sampled from the surface to the first zone of saturation and compared with soils from an adjacent un-contaminated control site. These elements were found to be accumulating in the first few centimeters of basin soil and are important to the effectiveness of a specific best management practice, i.e., the retention and recharge of urban storm water. Study basins in use since 1962, 1965, and 1969 had lead contents in the 0–2 cm soil depth interval‘of 570, 670, and 1400 mg Pb/kg soil, respectively. The median indigenous soil lead concentration was 4.6 mg/kg soil. The practice of removing excess flood runoff water from two basins by pumping apparently is a factor in reducing the accumulation rate of these elements in the surface soils of the basins.     

MANAGEMENT OF FLOOD CONTROL SUMPS AND POLLUTANT TRANSPORT1

ABSTRACT: Levee sump systems are used by many riverine communities for temporary storage of urban wet weather flows. The hydrologic performance and transport of stormwater pollutants in sump systems, however, have not been systematically studied. The objective of this paper is to present a case study to demonstrate development and application of a procedure for assessing the hydraulic performance of flood control sumps in an urban watershed. Two sumps of highly variable physical and hydraulic characteristics were selected for analysis. A hydrologic modeling package was used to estimate the flow hydrograph for each outfall as part of the flow balance for the sump. To validate these results, a water balance was used to estimate the total runoff using sump operational data. The hydrologic model calculations provide a satisfactory estimate of the total runoff and its time‐distribution to the sump. The model was then used to estimate pollutant loads to the sump and to the river. Although flow of stormwater through a sump system is regulated solely by flood‐control requirements, these sumps may function as sedimentation basins that provide purification of stormwater. A sample calculation of removals of several conventional pollutants in the target sumps using a mass balance approach is presented.     

Dry Weather Water Quality Loadings in Arid,Urban Watersheds of the Los Angeles Basin,California, USA1

Abstract: Dry weather runoff in arid, urban watersheds may consist entirely of treated wastewater effluent and/or urban nonpoint source runoff, which can be a source of bacteria, nutrients, and metals to receiving waters. Most studies of urban runoff focus on stormwater, and few have evaluated the relative contribution and sources of dry weather pollutant loading for a range of constituents across multiple watersheds. This study assessed dry weather loading of nutrients, metals, and bacteria in six urban watersheds in the Los Angeles region of southern California to estimate relative sources of each constituent class and the proportion of total annual load that can be attributed to dry weather discharge. In each watershed, flow and water quality were sampled from storm drain and treated wastewater inputs, as well as from in‐stream locations during at least two time periods. Data were used to calculate mean concentrations and loads for various sources. Dry weather loads were compared with modeled wet weather loads under a range of annual rainfall volumes to estimate the relative contribution of dry weather load. Mean storm drain flows were comparable between all watersheds, and in all cases, approximately 20% of the flowing storm drains accounted for 80% of the daily volume. Wastewater reclamation plants (WRP) were the main source of nutrients, storm drains accounted for almost all the bacteria, and metals sources varied by constituent. In‐stream concentrations reflected major sources, for example nutrient concentrations were highest downstream of WRP discharges, while in‐stream metals concentrations were highest downstream of the storm drains with high metals loads. Comparison of wet vs. dry weather loading indicates that dry weather loading can be a significant source of metals, ranging from less than 20% during wet years to greater than 50% during dry years.     

WATER QUALITY BENEATH URBAN RUNOFF WATER MANAGEMENT BASINS1

ABSTRACT: The chemical impact of urban runoff water on water quality beneath five retention/recharge basins was investigated as part of the US EPA's Nationwide Urban Runoff Program in Fresno, California. Soil water percolating through alluvium soils and the ground water at the top of the water table were sampled with ceramic/Teflon vacuum water extractors at depths up to 26 m during the two-year investigation. Inorganic and organic pollutants are present in the runoff water delivered to the basins. No significant contamination of percolating soil water or ground water underlying any of the five retention/recharge basins has occurred for constituents monitored in the study. The oldest basins was constructed in 1962. The concentration of selected trace elements in the ground water samples was similar to the levels reported in the regional ground water. None of the pesticides or other organic priority pollutants, for which water samples were analyzed, was s̊ detected except diazinon which was found in trace amounts (0.3 μg/L or less) in only three soil water samples. These results are important to the continued conservation of storm water and the development of a best management practice for storm-water management using retention/recharge basins in a semi-arid climate.     

The Influence of Urban Density and Drainage Infrastructure on the Concentrations and Loads of Pollutants in Small Streams

Effective water quality management of streams in urbanized basins requires identification of the elements of urbanization that contribute most to pollutant concentrations and loads. Drainage connection (the proportion of impervious area directly connected to streams by pipes or lined drains) is proposed as a variable explaining variance in the generally weak relationships between pollutant concentrations and imperviousness. Fifteen small streams draining independent subbasins east of Melbourne, Australia, were sampled for a suite of water quality variables. Geometric mean concentrations of all variables were calculated separately for baseflow and storm events, and these, together with estimates of runoff derived from a rainfall-runoff model, were used to estimate mean annual loads. Patterns of concentrations among the streams were assessed against patterns of imperviousness, drainage connection, unsealed (unpaved) road density, elevation, longitude (all of which were intercorrelated), septic tank density, and basin area. Baseflow and storm event concentrations of dissolved organic carbon (DOC), filterable reactive phosphorus (FRP), total phosphorus (TP) and ammonium, along with electrical conductivity (EC), all increased with imperviousness and its correlates. Hierarchical partitioning showed that DOC, EC, FRP, and storm event TP were independently correlated with drainage connection more strongly than could be explained by chance. Neither pH nor total suspended solids concentrations were strongly correlated with any basin variable. Oxidized and total nitrogen concentrations were most strongly explained by septic tank density. Loads of all variables were strongly correlated with imperviousness and connection. Priority should be given to low-impact urban design, which primarily involves reducing drainage connection, to minimize urbanization-related pollutant impacts on streams.     

Modeling Watershed‐Scale Impacts of Stormwater Management with Traditional versus Low Impact Development Design

Stormwater runoff and associated pollutants from urban areas in the greater Chesapeake Bay Watershed (CBW) impair local streams and downstream ecosystems, despite urbanized land comprising only 7% of the CBW area. More recently, stormwater best management practices (BMPs) have been implemented in a low impact development (LID) manner to treat stormwater runoff closer to its source. This approach included the development of a novel BMP model to compare traditional and LID design, pioneering the use of comprehensively digitized storm sewer infrastructure and BMP design connectivity with spatial patterns in a geographic information system at the watershed scale. The goal was to compare total watershed pollutant removal efficiency in two study watersheds with differing spatial patterns of BMP design (traditional and LID), by quantifying the improved water quality benefit of LID BMP design. An estimate of uncertainty was included in the modeling framework by using ranges for BMP pollutant removal efficiencies that were based on the literature. Our model, using Monte Carlo analysis, predicted that the LID watershed removed approximately 78 kg more nitrogen, 3 kg more phosphorus, and 1,592 kg more sediment per square kilometer as compared with the traditional watershed on an annual basis. Our research provides planners a valuable model to prioritize watersheds for BMP design based on model results or in optimizing BMP selection.     

Modeling the relationship between development and storm water and nutrient runoff

The EPA Storm Water Management Model was used to model the effects of urban and agricultural development on storm water runoff from uplands bordering a Louisiana swamp forest. Using this model, we examined the effects of changing land use patterns. By 1995 it is projected that urban land on the uplands bordering the swamp will increase by 321 percent, primarily at the expense of land currently in agriculture. Simulation results indicate that urbanization will cause storm water runoff rates to be up to 4.2 times greater in 1995 than in 1975. Nutrient runoff will increase 28 percent for nitrogen (N) and 16 percent for phosphorus (P) during the same period. The environmental effects of these changes in the receiving swamp forest are examined.     

成都市某区暴雨径流过程模拟分析

为提高城市雨洪管理的效率,最大限度地减少暴雨洪水带来的危害,针对城市防洪排涝的需要,在分析成都市某区降雨径流规律后,建立了该区暴雨径流模拟的数学模型,有助于采取相应措施充分利用雨洪资源。通过对雨洪过程模拟验证表明,模型适合该区域的实际情况,具有一定的合理性和可靠性。     

DESIGN OF A DIVERSION SYSTEM TO MANAGE THE FIRST FLUSH1

ABSTRACT: To manage the first flush of storm runoff in urbanized areas, a diversion box and detention basin system has been proposed for a new storm sewer system or for retrofitting an existing system. A software package for a personal computer has been developed to facilitate the analysis and design of the system. Hydrographs and pollutographs are generated at the inlet and outlet of the diversion box and the detention basin. The peak outflow and peak pollutant concentrations are compared with the allowable outflow and pollutant concentration for urban stormwater quantity and quality management. The model is developed for both analysis and design purposes.     

Runoff Curve Numbers at the Agricultural Field‐Scale and Implications for Continuous Simulation Modeling

This study used monitoring in the waterways of agricultural fields to understand the use of the runoff curve number (CN) in continuous simulation models. The CN has a long history as a design tool for estimating runoff volumes for large, single storms on small watersheds, but its use in continuous simulation models to describe runoff from smaller storms and relatively small areas is more recent and controversial. We examined 788 nonwinter rainfall events on four agricultural fields over five years (2004‐2008) during which runoff was generated in 87 events. The largest 20 runoff events on each field generated approximately 90% of the total runoff volume. The runoff event CNs showed an inverse correlation with storm depth that could not consistently be explained by previous precipitation. We review how small areas of higher runoff generation within larger areas will systematically increase the apparent CN of the larger area as the storm size decreases. If this variation is not incorporated into a model explicitly, continuous simulation modelers must understand that when source areas are aggregated or when runoff generation is spatially variable, the overall CN is not unique when smaller storms are included in the calibration set.     

PLANNING OF URBAN BEST MANAGEMENT PRACTICES1

ABSTRACT: A “user-friendly” computer program has been developed for application in personal computers for preliminary design, evaluation, and cost effectiveness analysis of various best management practice (BMP) measures to control stormwater quantity and quality. The algorithms utilize the SCS TR-55 method for calculating runoff hydrographs for a single storm event and a first order pollutant washoff equation to generate pollutographs. Sensitivity analyses based on different policy scenarios is performed on a hypothetical watershed for the purpose of illustration. Three types of BMP measures, namely detention ponds (dry, wet, and extended wet ponds), infiltration trenches, and porous pavements are considered. It is found that the extended wet ponds have the best cost effective performance of the measures evaluated.     

Management of Urban Road Runoff Containing PAHs: Probabilistic Modeling and Its Application in Beijing,China1

Abstract: Pollutant loading from storm runoff is considered to be an important component of nonpoint source pollution in urban areas. In developing countries, because of the accelerated urbanization and motorization, storm runoff pollution has become a challenge for improving aquatic environmental quality. An effective storm runoff management plan needs to be developed, and questions concerning how much and which proportion of a storm should be treated need to be answered. In this study, a model is developed to determine the fraction of storm runoff that needs to be treated to meet the discharge standard within a given probability. The model considers that the pollutants can be mobilized during the early stage of a storm. The model is applied to a field study of polycyclic aromatic hydrocarbons (PAHs) in road runoff in Beijing, China. In this case, the probability that the PAH load will be mobilized with suspended sediments by the earlier portion of the flush is 73%. Given the high PAH loading in the study area and the referenced discharge standard, the probability that the entire runoff should be captured and treated is 94%. Thus, urban planners need to consider treatment systems for the majority of the storms in this area, whether the PAH load is in the first flush or not. This methodology can be applied to other regions where PAH loads may result in different management outcomes.     

Variation of Nitrogen Concentrations in Stormpipe Discharge in a Residential Watershed1

Abstract: Use of lawn chemicals in residential areas may contribute nonpoint source (NPS) pollutants, such as nutrients, pesticides, and herbicides to streams. We conducted a 2‐year screening study of discharge in stormwater pipes in the Wissahickon Valley Watershed (suburban Philadelphia) using nitrogen as an indicator of lawn chemical use. Stormwater samples representing first flush and composite runoff were collected approximately twice a month using automatic samplers triggered by rise in water level during storms. The runoff collected by the stormpipes was from neighborhoods with 15‐100 residences, and from 2 to 18 ha (5‐45 acres). Several factors were examined to evaluate the effects on nitrate concentration. These factors included time of sampling (season), number of homes, total area, size of the storm, and time since last storm. Nitrate levels were generally less than 5 mg/l, but still above background in typical undeveloped areas. Concentrations were slightly higher in the first summer than during a drought in the second year, but the difference was not statistically significant. There was a positive correlation between size of the neighborhood (capture area) and peak concentration of nitrate. Storm characteristics (size of storm and time since last storm) did not correlate with nitrate concentrations. The variation in both space and time suggests that a more local control may be a factor. Although individual lawn chemical applications were not monitored, they may influence the timing of increased loading. Furthermore, the variability indicates that quarterly monitoring will not capture discharge characteristics of storm basins.     

STORM WATER MANAGEMENT: THE CONCEPT AND ITS APPLICATION1

ABSTRACT: Storm water management is a concept being applied in many urban areas to deal with the increasing problems of storm runoff control and flood damage prevention. This paper introduces the concept and describes the recently completed storm water management program in Columbus, Georgia. Columbus has spent five years and over $200,000 in the development of their problem which includes several basic elements: soils inventory and analysis, hydrologic data collection, sediment and erosion control ordinance, storm water management handbook, urban flood simulation model, interdepartment coordination study, drainage problem categorization study, and a pilot basin study. The results of the pilot basin study are presented including example output from the urban simulation model. The computer output illustrates both the hydrologic-hydraulic and economic capabilities of the model.     

Evaluation of seasonal scale first flush pollutant loading and implications for urban runoff management

This study investigated how the occurrence and magnitude of first flush events in stormwater may influence the effective management of urban runoff pollution. To facilitate the understanding of the first flush phenomenon on a seasonal scale, the City of San Jose, CA carried out an investigation between May 1997 and April 2000 to characterize concentrations of pollutants in local waterbodies during eight storm events. The purpose of the investigation was twofold: (1) To determine if concentrations of specific constituents in stormwater runoff are elevated during the first substantial storm of the wet season, and (2) To identify the physical and environmental conditions surrounding such events. Concentration data for total and dissolved metals, pesticides, polyaromatic hydrocarbons, anions, total suspended solids, total organic carbon, conductivity, gasoline and diesel, and volatile and semi-volatile organics were collected at over 25 sites. Monitoring data analysis focused on identifying physical and environmental conditions yielding increased levels of pollutants during the first substantial storms of the rainy season compared to other storm events. Quantitative analysis focused on metals and anions because most observations for other constituents were below detectable levels. The results suggest that first flush phenomena did not occur consistently throughout most of the stations investigated. The results further suggest that there are specific combinations of site and storm conditions that result in a first flush effect with respect to dissolved metals. Based on the results of this and related investigations, implications for urban runoff management are discussed. For example, if dissolved metals are of principal concern, it may be worthwhile to optimize existing control strategies to minimize pollutant loading from storms that are preceded by an extended dry period.     

CALIBRATION OF STORM LOADS IN THE SOUTH PRONG WATERSHED,FLORIDA, USING BASINS/HSPF1

ABSTRACT: The South Prong watershed is a major tributary system of the Sebastian River and adjacent Indian River Lagoon. Continued urbanization of the Sebastian River drainage basin and other watersheds of the Indian River Lagoon is expected to increase runoff and nonpoint source pollutant loads. The St. Johns River Water Management District developed watershed simulation models to estimate potential impacts on the ecological systems of receiving waters and to assist planners in devising strategies to prevent further degradation of water resources. In the South Prong system, a storm water sampling program was carried out to calibrate the water quality components of the watershed model for total suspended solids (TSS), total phosphorous (TP), and total nitrogen (TN). During the period of May to November 1999, water quality and flow data were collected at three locations within the watershed. Two of the sampling stations were located at the downstream end of major watercourses. The third station was located at the watershed outlet. Five storm events were sampled and measured at each station. Sampling was conducted at appropriate intervals to represent the rising limb, peak, and recession limb of each storm event. The simulations were handled by HSPF (Hydrologic Simulation Program‐Fortran). Results include calibration of the hydrology and calibration of the individual storm loads. The hydrologic calibration was continuous over the period 1994 through 1999. Simulated storm runoff, storm loads, and event mean concentrations were compared with their corresponding observed values. The hydrologic calibration showed good results. The outcome of the individual storm calibrations was mixed. Overall, however, the simulated storm loads agreed reasonably well with measured loads for a majority of the storms.