Compost mixture influence of interactive physical parameters on microbial kinetics and substrate fractionation

Composting is a feasible biological treatment for the recycling of wastewater sludge as a soil amendment. The process can be optimized by selecting an initial compost recipe with physical properties that enhance microbial activity. The present study measured the microbial O₂ uptake rate (OUR) in 16 sludge and wood residue mixtures to estimate the kinetics parameters of maximum growth rate μ_m and rate of organic matter hydrolysis K_h, as well as the initial biodegradable organic matter fractions present. The starting mixtures consisted of a wide range of moisture content (MC), waste to bulking agent (BA) ratio (W/BA ratio) and BA particle size, which were placed in a laboratory respirometry apparatus to measure their OUR over 4 weeks. A microbial model based on the activated sludge process was used to calculate the kinetic parameters and was found to adequately reproduced OUR curves over time, except for the lag phase and peak OUR, which was not represented and generally over-estimated, respectively. The maximum growth rate μ_m, was found to have a quadratic relationship with MC and a negative association with BA particle size. As a result, increasing MC up to 50% and using a smaller BA particle size of 8–12 mm was seen to maximize μ_m. The rate of hydrolysis K_h was found to have a linear association with both MC and BA particle size. The model also estimated the initial readily biodegradable organic matter fraction, MB₀, and the slower biodegradable matter requiring hydrolysis, MH₀. The sum of MB₀ and MH₀ was associated with MC, W/BA ratio and the interaction between these two parameters, suggesting that O₂ availability was a key factor in determining the value of these two fractions. The study reinforced the idea that optimization of the physical characteristics of a compost mixture requires a holistic approach.     

Composting anaerobic and aerobic sewage sludges using two proportions of sawdust

Sawdust has been proven to be a good bulking agent for sludge composting; however, studies on the most suitable ratio of sludge:sawdust for sludge composting and on the influence of the sludge nature (aerobic or anaerobic) on the composting reaction rate are scarce. In this study two different sewage sludges (aerobic, AS, and anaerobic, ANS) were composted with wood sawdust (WS) as bulking agent at two different ratios (1:1 and 1:3 sludge:sawdust, v:v). Aerobic sludge piles showed significantly higher microbial activity than those of anaerobic sludge, organic matter mineralization rates being higher in the AS mixtures. The lowest thermophilic temperatures during composting were registered when the anaerobic sludge was mixed with sawdust at 1:1 ratio, suggesting the presence of substances toxic to microorganisms. This mixture also showed the lowest decreases of ammonium during composting. All this matched with the inhibitory effect on the germination of Lepidium sativum seeds of this mixture at the first stages of composting, and with its low values of microbial basal respiration. However, the ANS+WS 1:3 compost developed in a suitable way; the higher proportion of bulking agent in this mixture appeared to have a diluting effect on these toxic compounds. Both the proportions assayed allowed composting to develop adequately in the case of the aerobic sludge mixture, yielding suitable composts for agricultural use. However, the ratio 1:1 seems more suitable because it is more economical than the 1:3 ratio and has a lower dilution effect on the nutritional components of the composts. In the case of the anaerobic sludge with its high electrical conductivity and ammonium content, and likely presence of other toxic and phytotoxic substances, the 1:3 ratio is to be recommended because of the dilution effect.     

Fate of mutagenic chemicals in soil amended with petroleum and wood preserving sludges

A field study using monoliths (lysimeters) of a sandy clay loam soil was conducted to assess the fate of mutagenic chemicals after refinery and wood preserving bottom sediment sludges were land treated. The Ames Salmonella/microsome assay¹ was used to determine the direct (without metabolic activation, −S9) and indirect (with metabolic activation, + S9) mutagenicity of the wastes, unamended soil, waste amended soils, and leachate. Extracts having a mutagenic ratio (MR) (MR= No. colonies from sample extract/No. colonies from DMSO solvent control) of ⩾ 2 were considered positively mutagenic. Extracts of the wood preserving waste sludge without activation were non-mutagenic (MR < 2) but extracts with activation ( + S9) produced very strong indirect mutagenicity (MR = 7.9). After soil incorporation, the waste amended soil produced very strong direct (MR = 8.9) and indirect (MR = 11.9) mutagenicity by day 180 and remained mutagenic (MR = 5.7, −S9; MR = 3.95, + S9) through day 350. The amount of residue in leachate from the wood preserving waste amended lysimeters was significantly greater (P <0.05) than the unamended soil during the first 90 days after waste application, but was not different after 90 days. The leachate residue from wood preserving waste amended lysimeters in the 90–180-day period produced mutagenic responses both with (MR = 2.24 and 2.51) and without (MR = 2.29) activation. Polynuclear aromatic hydrocarbons were the main constituents identified in the leachate residues that produced a mutagenic response. Soil treatment of the refinery sludge reduced its weak indirect mutagenicity before soil incorporation (MR = 2) to non-mutagenic (MR = 1.4) immediately following soil treatment. The MR of the waste amended soil increased to 1.7 by day 180 but by day 350 decreased to a level equal to that observed at day 0 (MR = 1.4). Leachate from the refinery amended lysimeters had significantly greater (P < 0.05) amounts of organic residue than unamended lysimeters 180 to 350 days after waste application. The leachate from one refinery waste amended lysimeter (90–180 days after waste application) produced a mutagenic response (MR = 3.16). The refinery sludge was detoxified shortly after soil treatment, but the wood preserving sludge required > 350 days to detoxify in the soil environment. The possibility exists that mobile mutagenic chemicals may leach into underlying groundwater from the treatment zone of soils amended with refinery and wood preserving sludges.     

Odorous gaseous emissions as influence by process condition for the forced aeration composting of pig slaughterhouse sludge

Compost sustainability requires a better control of its gaseous emissions responsible for several impacts including odours. Indeed, composting odours have stopped the operation of many platforms and prevented the installation of others. Accordingly, present technologies collecting and treating gases emitted from composting are not satisfactory and alternative solutions must be found. Thus, the aim of this paper was to study the influence of composting process conditions on gaseous emissions. Pig slaughterhouse sludge mixed with wood chips was composted under forced aeration in 300 L laboratory reactors. The process conditions studied were: aeration rate of 1.68, 4.03, 6.22, 9.80 and 13.44 L/h/kg of wet sludge; incorporation ratio of 0.55, 0.83 and 1.1 (kg of wet wood chips/kg of wet sludge), and; bulking agent particles size of <10, 10 < 20 and 20 < 30 mm. Out-going gases were sampled every 2 days and their composition was analysed using gas chromatography coupled with mass spectrometry (GC–MS). Fifty-nine compounds were identified and quantified. Dividing the cumulated mass production over 30 days of composting, by odour threshold, 9 compounds were identified as main potential odour contributors: hydrogen sulphide, trimethylamine, ammonia, 2-pentanone, 1-propanol-2-methyl, dimethyl sulphide, dimethyl disulphide, dimethyl trisulphide and acetophenone. Five gaseous compounds were correlated with both aeration rate and bulking agent to waste ratio: hydrogen sulphide, trimethylamine, ammonia, 2-pentanone and 1-propanol-2-methyl. However, dropping the aeration rate and increasing the bulking agent to waste ratio reduced gaseous odour emissions by a factor of 5–10, when the required threshold dilution factor ranged from 10⁵ to 10⁶, to avoid nuisance at peak emission rates. Process influence on emissions of dimethyl sulphide, dimethyl disulphide, dimethyl trisulphide were poorly correlated with both aeration rate and bulking agent to waste ratio as a reaction with hydrogen sulphide was suspected. Acetophenone emissions originated from the wood chips. Olfactory measurements need to be correlated to gaseous emissions for a more accurate odour emission evaluation.     

Microbial oxygen uptake in sludge as influenced by compost physical parameters

The wide range of optimal values reported for the physical parameters of compost mixtures suggest that their interactive relationships should be investigated. The objective of this study was to examine the microbial O₂ uptake rate (OUR) in 16 sludge waste recipes, offering a range of moisture content (MC), waste/bulking agent (W/BA) ratio and BA particle size levels determined using a central composite experimental design. The 3 kg samples were maintained at a constant temperature and aeration rate for 28 days, during which a respirometer recorded O₂ uptake to provide a measure of microbial activity and biodegradability. The cumulative O₂ consumption after 14 and 28 days was found to be significantly influenced by MC, W/BA ratio, BA particle size and the interaction between MC and W/BA ratio (p < 0.05). Using multivariate regression analysis, the experimental data was used to generate a model with good predictive ability for cumulative O₂ consumption after 28 days as a function of the significant physical variables (R² = 0.84). The prediction of O₂ uptake by the model depended highly on the interaction between MC and W/BA ratio. A MC outside of the traditional 50–60% (wet basis) range still resulted in a high level of microbial O₂ uptake as long as the W/BA ratio was adjusted to maintain a suitable O₂ exchange in the sample. The evolution of OUR in the samples was also investigated, uncovering strong associations between short and long-term respirometric indices, such as peak OUR and cumulative O₂ consumption (p < 0.005). Combining peak OUR data with cumulative O₂ consumption after 14 days allowed for accurate predictions of cumulative O₂ after 28 days of aeration (R² = 0.96), implying that future studies need only run trials up to 14 days to evaluate the overall O₂ consumption or biodegradability of similar sludge mixtures.     

Effect of different tannery sludge compost amendment rates on growth,biomass accumulation and yield responses of Capsicum plants

Composting has been recognized as one of the most cost effective and environmentally sound alternatives for organic wastes recycling from long and composted wastes have a potential to substitute inorganic fertilizers. We investigated the potential of composted tannery sludge for ornamental purposes and to examine the effects of two different composts and concentrations on ornamental Capsicum growth. The two composts were produced with tannery sludge and the composition of each compost was: compost₁ of tannery sludge (C₁TS) – tannery sludge + sugarcane straw and cattle manure mixed in the ratio 1:3:1 (v:v:v); compost₂ of tannery sludge (C₂TS) – tannery sludge + “carnauba” straw and cattle manure in the ratio 1:3:1 (v:v:v). Each compost was amended with soil at rates (% v:v) of 0%, 25%, 50%, 75% and 100% (designation hereafter as T₁–T₅, respectively). The number of leaves and fruits were counted, and the stem length was also measured. Chlorophyll content was recorded on three leaves of each harvested plant prior to harvest. Number of leaves and fruits, stem length, dry weight of shoot and roots did not vary significantly between the plants grown in two tannery composts. All the treatments with composted tannery sludge application (T₂–T₅) significantly increased the number of leaves and fruits, stem length and chlorophyll content compared with the control (T₁). The chlorophyll content was higher in plants growing in the C₁TS compared to C₂TS. The results of the present study further suggest that Capsicum may be a good option to be grown on composted tannery amended soil.     

Bioconversion of industrial wastes: paint sludge from automotive manufacturing

The compostability of water-based paint sludge originating from the automotive industry was investigated. Six reactors were operated. Wastewater treatment sludge from the same industry was used as additional substrate, and corncob was used as a bulking agent. The level of paint sludge within the compost mixtures varied between 55 and 85%. All reactors yielded a temperature increase up to thermophilic phase levels (>?40 °C) for a minimum of 5 days, and organic matter and C/N losses were observed. BTEX concentrations decreased during composting. Nickel and tin levels in the final product exceeded the legal compost limits. The calorific value of the compost mixtures increased from 9532 to 18774 kJ/kg at the end of the composting process. It was seen that the process applied in this study can be utilized as a biodrying step before the usage of paint sludge at cement kilns as additional fuel.     

Optimal bulking agent particle size and usage for heat retention and disinfection in domestic wastewater sludge composting

Composting of two types of sludge produced in wastewater treatment plants, raw sludge (RS) and anaerobically digested sludge (ADS), has been systematically studied by means of the experimental design technique. The results have been analyzed using a full factorial experimental design in order to determine the optimal conditions for composting such sludges in terms of bulking agent particle size and bulking agent:sludge volumetric ratio, two of the key parameters to ensure an optimal performance of the composting process. The objective function selected was a simulated death kinetics of Salmonella, which was chosen as a model pathogen microorganism to represent the disinfection of the material. For both types of sludge, optimal values were found at 5mm bulking agent particle size and 1:1 bulking agent:sludge volumetric ratio when a Gaussian function was fitted to the experimental data. Pilot scale experiments using optimal values obtained were successfully undertaken and confirmed a full disinfection of the sludge by means of the composting process. A mathematical model to simulate the disinfection performance of a composting material is presented. The model can be applied to simulate the disinfection performance of a given pathogen.     

Sewage sludge composting: Influence of initial mixtures on organic matter evolution and N availability in the final composts

The influence of bulking agents on organic matter (OM) stability and nitrogen (N) availability in sewage sludge composts was investigated. The same sludge was composted on an industrial plant with different mixtures of bulking agents. The composting process included an active phase and a curing phase, both lasting 6 weeks, separated by the screening of composts. The OM evolution was characterised by carbon (C) and N mass balances in biochemical fractions. The OM stability and N potential availability of final composts were measured during soil incubations. During composting, the C and N losses reached more than 62% of the initial C and more than 45% of the initial N, respectively, due to C mineralisation or N volatilisation and screening. The bulking materials mostly influenced OM evolution during the active phase. They contributed to the mitigation of N losses during the active phase where N immobilisation through active microbial activity was favoured by bulking agents increasing the C:N ratio of the initial mixtures. However, the influence of bulking agents on OM evolution was removed by the screening; this induced the homogenisation of compost characteristics and led to the production of sludge composts with similar organic matter characteristics, C degradability and N availability.     

Effects of Waste Paper Sludge on the Physico-Mechanical Properties of High Density Polyethylene/Wood Flour Composites

The objective of this work was to determine some physical and mechanical properties of the high density polyethylene (HDPE) composites reinforced with various mixtures of the paper sludge and the wood flour, and to evaluate the coupling agent performance. The waste sludge materials originating from two different sources including paper making waste water treatment sludge (PS) and ink-eliminated sludge (IES) were characterized in terms of physico-chemical properties. In the experiment, four levels of paper sludge (20, 30, 40 and 60 wt%), three levels of wood flour (20, 40 and 60 wt%), and two levels of coupling agent (MAPE) content (2 and 3 wt%) were used. The flexural properties of the composites were positively affected by the addition of the sludge. Especially, tensile modulus improved with the increase of paper sludge content. With the addition of MAPE, flexural properties improved considerably compared with control specimens (without any coupling agent). The results showed that the water absorption (WA) and thickness swelling (TS) values of the samples decreased considerably with increasing sludge content in the composite, while they increased with increasing wood flour content. It is to be noted that with incorporation of MAPE in the composite formulation, the compatibility between the wood flour and HDPE was enhanced through esterification, which reduced the WA and TS and improved the mechanical properties. Composites made with IES exhibited superior physico-mechanical properties compared with the PS filled composites. Overall results suggest that the waste paper sludge materials were capable of serving as feasible reinforcing fillers for thermoplastic polymer composites.     

Effect of light Sphagnum peat on odour formation in the early stages of biowaste composting

In the present study, we investigated the effects of two bulking materials, Sphagnum peat and pine wood chips, on the early stages of biowaste composting in two pilot-scale processes. Emphasis was placed on studying the formation conditions of malodorous compost gases in the initial phases of the processes. The results showed that gas emission leaving an open windrow and a closed drum composting system contained elevated concentrations of fermentative microbial metabolites when acid Sphagnum peat (pH 3.2) was used as a bulking material. Moreover, the gas emission of the peat amended drum composter contained a high concentration of odour (up to 450,000 ou m^?3 of air). The highest odour values in the outlet gas of peat amended composts coincided with the elevated concentrations of volatile organic compounds such as acetoin and buthanedion. We conclude that the acidifying qualities of composting substrates or bulking material may intensify odour emission from biowaste composts and prolong the early stages of the composting process.     

Tween 20 and Its Major Free Fatty Acids as Carbon Substrates for the Production of Polyhydroxyalkanoates in Pseudomonas aeruginosa ATCC 27853

The ability of Pseudomonas aeruginosa ATCC 27853 to grow and synthesize polyhydroxyalkanoates (PHAs) using Tween 20 as the sole carbon source was investigated. Tween 20 could support cell growth and PHA production. The polymer produced from Tween 20 was compared with those produced from its major free fatty acids components: lauric (C₁₂), myristic (C₁₄), and palmitic (C₁₆) acids. Gas-chromatographic analysis of methanolyzed samples and ¹³C-Nuclear Magnetic Resonance (NMR) showed that the PHAs obtained are composed of even carbon atoms 3-hydroxyalkanoates ranging from C₆ to C₁₄, with C₈ and C₁₀ as the predominant components. The nature of the carbon sources used had little influence on the composition, but was found to be important in determining the average molecular weight, shorter chain fatty acids yielding higher molecular weight products. Fast Atom Bombardment-Mass Spectrometry (FAB-MS) of partially pyrolyzed samples, coupled to statistical analysis, showed that these PHAs are random copolymers.     

Qualitative and Quantitative Analysis of Lignin Produced from Beech Wood by Different Conditions of the Organosolv Process

Lignins in general have been extensively studied, while beech wood lignin in particular is rarely researched. In the present work, Organosolv isolated lignin from beech wood (OBL) has been characterized. The isolation was done by two methods: (a) by using sulfuric acid at 170 °C and a reaction time of 120 min and (b) at a temperature of 180 °C for 240 min. A range of analytical methods were applied including elemental analysis, FT-IR, UV–Vis, ³¹P NMR, SEC, Pyrolysis-GC/MS and HPLC to gain information about establish the purity, structure, molecular weight, thermal behavior and to determine carbohydrate residues according to the NREL protocol. FT-IR and UV–Vis spectra of OBL revealed expected typical absorptions for lignins. NREL analysis presented a carbohydrate-free lignin fraction which has not been achieved to date. TGA and DSC are used to study the thermal behavior of the isolated lignins and showed a relatively low glass transition temperatures (T_g: 123 °C) and decomposition temperatures of 348 and 381 °C. The pyrograms generated from the pyrolysis–GC/MS at 550 °C consisted mainly of fragments of syringyl, guaiacyl and hydroxyphenyl units, thereby confirming the results of the NMR analysis. Our findings support Organolsolv as an efficient method to isolate pure lignin fractions from beech wood with practical value in industry.     

Gasification characteristics of sewage sludge combined with wood biomass

The gas products from gasification processes have been considered to have some limitations in gas composition and heating value from the previous studies. Gasification characteristics of sewage sludge and wood mixture were investigated using different mixing ratios with the purpose of better quality of gas product suitable for energy/power generation. The gasification experiment was performed by an indirectly heated fluidized bed reactor. As reaction temperature increased from 600 to 900 °C, the yield of gas product increased with higher generation of CO, H₂ and CH₄ by more activated gas conversion reactions. As the equivalence ratio increased from 0.2 to 0.4, composition ratio of CO₂ increased while CO, CH₄, H₂ decreased as expected. Several operating variables including mixing ratio of wood with dried sludge were also tested. From this initial stage of experiment, optimal operating conditions for the bubbling fluidized bed gasifier, could be considered 900 °C in temperature; 0.2 in equivalence ratio and 40 % in wood mixing ratio within test variables range. These results will be more thoroughly investigated for the application to the larger scale pilot system.     

Possible use of sludge ash as filler in natural rubber

Potential use of sludge ash as a filler in NR was studied. In this study, two grades of sludge ash namely SA-300 and SA-700 were prepared by sintering sludge waste obtained from concentrated natural rubber (NR) latex production at 300 and 700 °C, respectively. Properties of NR filled with various contents of SA-300 and SA-700 were then investigated and compared with those of NR filled with precipitated calcium carbonate (CaCO₃). The results reveal that, regardless of the filler type, both scorch time (t _s1) and optimum cure time (t _c90) decrease whereas hardness and modulus increase with increasing filler loading. At a given loading, both SA-300 and SA-700 give shorter scorch time and cure time with higher hardness and modulus than CaCO₃. Due to their higher specific surface area and greater cure activation efficiency, SA-300 and SA-700 provide better reinforcement, i.e., greater tensile strength; tear strength and abrasion resistance than CaCO₃. Taken as a whole, it could be said that the two grades of sludge ash could be utilized as rubber fillers with economic advantage.     

Effect of composting on the Cd,Zn and Mn content and fractionation in feedstock mixtures with wood chips from a short-rotation coppice and bark

Micronutrient content and availability in composts may be affected by the addition of wood chips or tree bark as a bulking agent in the compost feedstock. In the first part of this study, micronutrient levels were assessed in bark and wood of poplar and willow clones in a short-rotation coppice. Large differences between species were observed in bark concentrations for Cd, Zn and Mn. In the second part of the study, we aimed to determine the effect of feedstock composition and composting on Cd, Zn and Mn concentrations and availability. By means of three composting experiments we examined the effect of (a) bark of different tree species, (b) the amount of bark, and (c) the use of bark versus wood chips. In general, compost characteristics such as pH, organic matter and nutrient content varied due to differences in feedstock mixture and composting process. During the composting process, the availability of Cd, Zn and Mn decreased, although the use of willow and poplar bark or wood chips resulted in elevated total Cd, Zn or Mn concentrations in the compost. Cd concentrations in some composts even exceeded legal criteria. Cd and Zn were mainly bound in the reducible fraction extracted with 0.5 M NH₂OH?HCl. A higher acid-extractable fraction for Mn than for Cd and Zn was found. Higher Cd concentrations in the compost due to the use of bark or wood chips did not result in higher risk of Cd leaching. The results of the pH-stat experiment with gradual acidification of composts illustrated that only a strong pH decline in the compost results in higher availability of Cd, Zn and Mn.     

Comprehensive temperature monitoring in an in-vessel forced-aeration static-bed composting process

Comprehensive temperature monitoring was done in an in-vessel forced-aeration static-bed composting process using sewage sludge. The three layers that divided the compost pile horizontally showed different temperature distributions. The temperature of the top layer appeared not to be influenced by the ambient temperature. The temperature of the center area of the top layer was taken to be the representative temperature for evaluating composting start-up performance. The temperature of the bottom layer was strongly influenced by the ambient temperature, and the temperature of the center area of the bottom layer was taken to be the representative temperature for pathogen control as it was the minimum temperature in the reactor. Composting start-up performance was influenced by several factors when the ambient temperature was either below or above 20°C. When the ambient temperature was below 20°C, the time taken to reach 65°C (T ₆₅) was influenced by the temperature of inflowing air, but when the temperature was higher than 20°C, it was influenced by the ratio of sewage sludge to seed compost (F/S). T ₆₅ was least when F/S was 1–2. Received: January 9, 2001 / Accepted: October 10, 2001     

Determination of In Situ Esterification Parameters of Citric Acid-Glycerol Based Polymers for Wood Impregnation

The development of wood treatments is of increasing industrial importance. A novel technique for improving the properties of lodgepole pine and white pine through modification of the microstructure is described. The present investigation is devoted to the synthesis and determination of in situ parameters of citric acid and glycerol based polymers for wood impregnation. This solvent free approach is environmentally friendly and achieved through an esterification condensation reaction under acidic conditions. Crude glycerol and citric acid reactants were cross-linked via a curing process at 160?°C creating a polymer with only water as the byproduct. The ester bonds and crosslinking levels were controlled using different catalysts and citric acid contents and related to the reaction time and temperature. The nature of bonding within the polymers and at the wood cell walls was determined by FT-IR analysis. The thermal properties such as glass transition temperature (T_g) were studied using TGA/DSC and the effect of citric acid content and catalyst type determined. Dimensional stability of impregnated wood samples improved above 50% for each sample with HCl and p-TSA catalysts compared to control samples. FTIR spectra were studied to show the presence of the ester linkages of the polymer in situ at the wood cell walls. Bonding between the polymer and wood macromolecules were observed by scanning electron microscopy and interpreted as evidence of chemical bonds at the wood cells. When prepared using a catalyst, the polymer was intimately incorporated into wood structure significantly improving the substrate dimensional stability. Enhanced stability makes this approach of particular interest for exterior wood products especially as a green renewable option for the wood industry.     

Anaerobic digestion of chicken feather with swine manure or slaughterhouse sludge for biogas production

Biogas production from anaerobic digestion of chicken feathers with swine manure or slaughterhouse sludge was assessed in two separate experiments. Ground feathers without any pre-treatment were added to 42-L digesters inoculated with swine manure or slaughterhouse sludge, representing 37% and 23% of total solids, respectively and incubated at 25 °C in batch mode. Compared to the control without feather addition, total CH₄ production increased by 130% (P < 0.001) and 110% (P = 0.09) in the swine manure and the slaughterhouse sludge digesters, respectively. Mixed liquor NH₄N concentration increased (P < 0.001) from 4.8 and 3.1 g/L at the beginning of the digestion to 6.9 and 3.5 g/L at the end of digestion in the swine manure and the slaughterhouse sludge digesters, respectively. The fraction of proteolytic microorganisms increased (P < 0.001) during the digestion from 12.5% to 14.5% and 11.3% to 13.0% in the swine manure and the slaughterhouse sludge digesters with feather addition, respectively, but decreased in the controls. These results are reflective of feather digestion. Feather addition did not affect CH₄ yields of the swine manure digesters (P = 0.082) and the slaughterhouse sludge digesters (P = 0.21), indicating that feathers can be digested together with swine manure or slaughterhouse sludge without negatively affecting the digestion of swine manure and slaughterhouse sludge.     

Production of well-matured compost from night-soil sludge by an extremely short period of thermophilic composting

The effect of various operational conditions on the decomposition of organic material during the composting of night-soil treatment sludge was quantitatively examined. The optimum composting conditions were found to be a temperature of ca. 60 °C and an initial pH value of 8. Rapid decomposition of organic matter ceased by the sixth day of composting under these optimum conditions, and the final value of the cumulative emission of carbon (E_C), which represents the degree of organic matter decomposition, was less than 40%, indicating that the sludge contained only a small amount of easily degradable organic material. A plant growth assay using Komatsuna (Brassica campestris L. var. rapiferafroug) in a 1/5000a standard cultivation pot was then conducted for the compost at various degrees of organic matter decomposition: the raw composting material, the final compost obtained on day 6, and the 2 intermediate compost products (i.e., E_C = 10% and 20%). It was found that the larger the E_C, the greater the yield of Komatsuna growth. It was also found that 6 days of composting is sufficient to promote Komatsuna growth at the standard loading level, which is equivalent to a 1.5 g N/pot, since the promotion effect was as high as that obtained using chemical fertilizer. It can therefore be concluded that well-matured compost could be obtained in a short period of time (i.e., as early as 6 days), when night-soil sludge is composted under optimum conditions.