NO2 and SO2 dispersion modeling and relative roles of emission sources over Map Ta Phut industrial area, Thailand

Map Ta Phut industrial area (MA) is the largest industrial complex in Thailand. There has been concern about many air pollutants over this area. Air quality management for the area is known to be difficult, due to lack of understanding of how emissions from different sources or sectors (e.g., industrial, power plant, transportation, and residential) contribute to air quality degradation in the area. In this study, a dispersion study of NO2 and SO2 was conducted using the AERMOD model. The area-specific emission inventories of NOx and SO2 were prepared, including both stack and nonstack sources, and divided into 11 emission groups. Annual simulations were performed for the year 2006. Modeled concentrations were evaluated with observations. Underestimation of both pollutants was Jbund, and stack emission estimates were scaled to improve the modeled results before quantifying relative roles of individual emission groups to ambient concentration overfour selected impacted areas (two are residential and the others are highly industrialized). Two concentration measures (i.e., annual average area-wide concentration or AC, and area-wide robust highest concentration or AR) were used to aggregately represent mean and high-end concentrations Jbfor each individual area, respectively. For AC-NO2, on-road mobile emissions were found to be the largest contributor in the two residential areas (36-38% of total AC-NO2), while petrochemical-industry emissions play the most important role in the two industrialized areas (34-51%). For AR-NO2, biomass burning has the most influence in all impacted areas (>90%) exceptJor one residential area where on-road mobile is the largest (75%). For AC-SO2, the petrochemical industry contributes most in all impacted areas (38-56%). For AR-SO2, the results vary. Since the petrochemical industry was often identified as the major contributor despite not being the largest emitter, air quality workers should pay special attention to this emission group when managing air quality for the MA.     

Assessment of contribution of SO2 and NO2 from different sources in Jamshedpur region, India

Contribution of pollution from different types of sources in Jamshedpur, the steel city of India, has been estimated in winter 1993 using two approaches in order to delineate and prioritize air quality management strategies for the development of region in an environmental friendly manner. The first approach mainly aims at preparation of a comprehensive emission inventory and estimation of spatial distribution of pollution loads in terms of SO₂ and NO₂ from different types of industrial, domestic and vehicular sources in the region. The results indicate that industrial sources account for 77% and 68% of the total emissions of SO₂ and NO₂, respectively, in the region, whereas vehicular emissions contributed to about 28% of the total NO₂ emissions. In the second approach, contribution of these sources to ambient air quality levels to which the people are exposed to, was assessed through air pollution dispersion modelling. Ambient concentration levels of SO₂ and NO₂ have been predicted in winter season using the ISCST3 model. The analysis indicates that emissions from industrial sources are responsible for more than 50% of the total SO₂ and NO₂ concentration levels. Vehicular activities contributed to about 40% of NO₂ pollution and domestic fuel combustion contributed to about 38% of SO₂ pollution. Predicted 24-h concentrations were compared with measured concentrations at 11 ambient air monitoring stations and good agreement was noted between the two values. In-depth zone-wise analysis of the above indicates that for effective air quality management, industrial source emissions should be given highest priority, followed by vehicular and domestic sources in Jamshedpur region.     

A highly resolved temporal and spatial air pollutant emission inventory for the Pearl River Delta region, China and its uncertainty assessment

A highly resolved temporal and spatial Pearl River Delta (PRD) regional emission inventory for the year 2006 was developed with the use of best available domestic emission factors and activity data. The inventory covers major emission sources in the region and a bottom–up approach was adopted to compile the inventory for those sources where possible. The results show that the estimates for SO₂, NO_x, CO, PM₁₀, PM_2.5 and VOC emissions in the PRD region for the year 2006 are 711.4 kt, 891.9 kt, 3840.6 kt, 418.4 kt, 204.6 kt, and 1180.1 kt, respectively. About 91.4% of SO₂ emissions were from power plant and industrial sources, and 87.2% of NO_x emissions were from power plant and mobile sources. The industrial, mobile and power plant sources are major contributors to PM₁₀ and PM_2.5 emissions, accounting for 97.7% of the total PM₁₀ and 97.2% of PM_2.5 emissions, respectively. Mobile, biogenic and VOC product-related sources are responsible for 90.5% of the total VOC emissions. The emissions are spatially allocated onto grid cells with a resolution of 3 km × 3 km, showing that anthropogenic air pollutant emissions are mainly distributed over PRD central-southern city cluster areas. The preliminary temporal profiles were established for the power plant, industrial and on-road mobile sources. There is relatively low uncertainty in SO₂ emission estimates with a range of −16% to +21% from power plant sources, medium to high uncertainty for the NO_x emissions, and high uncertainties in the VOC, PM_2.5, PM₁₀ and CO emissions.     

Spatial surrogates for the disaggregation of CORINAIR emission inventories

CORINAIR atmospheric emission inventories are frequently used input data for air quality models with a domain situated in Europe. In CORINAIR emission inventories, sources are broken down over 11 major source categories. This paper presents spatial surrogates for the disaggregation of CORINAIR atmospheric emission inventories for input of air pollutants and particulate matter to grid or polygon based air quality model domains inside Europe. The basis for the disaggregation model was the CLC2000 land cover data to which statistical weights were added. Weights were population census data for residential emissions, employment statistics for agricultural and industrial area emissions, livestock statistics for ammonia emissions and annual aircraft movements for emissions realized by air transport. Additional road and off-road network information was used to disaggregate emissions realized by traffic. A comparison of top down produced emission estimates with spatially resolved national emission data for The Netherlands and the United Kingdom gave confidence in the present spatial surrogates as a tool for the top down production of atmospheric emission maps. Explained variance at a spatial resolution of 5 km was >70% for CO, NMVOC and NO_x, >60% for PM10 and almost 50% for SO₂.     

Estimating Long-Term Ground Level Concentrations of SO2 from Short-Term Peak Data

Maximum concentrations of sulfur dioxide vary approximately inversely as the square root of the averaging time for periods up to a year, a much longer time period than those reported in previously published studies. This finding is based on analyses of SO₂ and tracer gas concentrations measured in the vicinities of a test stack, a petrochemical complex, and eight power plants. Therefore, for a given set of emission conditions, long-term concentrations of SO₂ and other conservative pollutants emitted by well-defined sources can be rapidly estimated from maximum short-term concentrations, and vice versa. The scatter in the data corresponds to an estimation error of about a factor of three for averaging time conversions of one day to one year. This is approximately the same error associated with conventional calculations. Therefore, the use of averaging time conversions is justified as a rapid screening technique to estimate compliance with ambient air quality standards.     

Shock Wave Cleaning of Air Filters

The trends in and relationships between ambient air concentrations of sulfur dioxide and sulfate aerosols at 48 urban sites and 27 nonurban sites throughout the U.S. between 1963 and 1972 have been analyzed. The substantial decreases in ambient SO₂ concentrations measured at urban sites in the eastern and midwestern U.S. are consistent with the corresponding reductions in local SO₂ emissions, but these decreases have been accompanied by only modest decreases in ambient sulfate concentrations. Large differences in the amounts of SO₂ emitted within individual air quality control regions are associated with much smaller differences in the corresponding ambient sulfate concentrations. Substantial changes in the patterns of SO₂ emissions between air quality regions result in essentially no differences between ambient sulfate concentrations in those air quality regions. Comparisons of several air quality regions in the eastern and western U.S. with similar SO₂ emission levels and patterns of emissions clearly demonstrates the higher ambient sulfate concentration levels in eastern air quality control regions. Relationships between SO₂, sulfates, and vanadium concentrations at eastern nonurban U.S. sites cannot be explained by local emission sources. These various observed results can be best explained by long distance sulfur oxide transport with chemical conversion of SO₂ to sulfates occurring over ranges of hundreds of kilometers. This conclusion has been suggested earlier and the present analysis strongly supports previous discussions. An impact of long range transport of sulfates is to emphasize the need for Consistent strategies for reduction of sulfur oxides throughout large geographical regions. Additions of large capacities involving elevated sources in mid-continental or western regions could result in significant increases in sulfate concentrations well downwind of such sources. Some of the types of research activities required to quantitate crucial experimental parameters are discussed.     

Estimating Future NO2 Levels in the Greater Los Angeles Area by Source–Type Contribution

Two indicator pollutants, carbon monoxide (CO) for mobile source influence and sulfur dioxide (SO₂) for stationary source influence, were used to estimate source-type contributions to ambient NO₂ levels in a base year and to predict NO₂ concentrations in a future year. For a specific source-receptor pair, the so-called influence coefficient of each of three source categories (mobile sources, power plants, and other stationary sources) was determined empirically from concurrent measurements of CO and SO₂ concentrations at the receptor site and CO and SO₂ emissions from each source category in the source area. Those coefficients, which are considered time invariant, were used in conjunction with the base year and future year NO _x emission values to estimate source-type contribution to ambient NO₂ levels at seven study sites selected from the Greater Los Angeles area for both the base year period, 1974 through 1976, and the future goal year of 1987 in which the air quality standards for NO₂ are to be attained. The estimated NO₂ air quality at the seven sites is found to meet the national annual standard of 5 pphm and over 99.9% of total hours, the California 1-hr NO₂ standard of 25 pphm in 1987. The estimated power plant contributions to ambient NO₂ levels are found to be considerably smaller than those to total NO _x emissions in the area. Providing that reasonably complete air quality and emissions data are available, the present analysis method may prove to be a useful tool in evaluating source contributions to both short-term peak and long-term average NO₂ concentrations for use in control strategy development.     

PAH air pollution at a Portuguese urban area: carcinogenic risks and sources identification

This study aimed to characterize air pollution and the associated carcinogenic risks of polycyclic aromatic hydrocarbon (PAHs) at an urban site, to identify possible emission sources of PAHs using several statistical methodologies, and to analyze the influence of other air pollutants and meteorological variables on PAH concentrations.The air quality and meteorological data were collected in Oporto, the second largest city of Portugal. Eighteen PAHs (the 16 PAHs considered by United States Environment Protection Agency (USEPA) as priority pollutants, dibenzo[a,l]pyrene, and benzo[j]fluoranthene) were collected daily for 24 h in air (gas phase and in particles) during 40 consecutive days in November and December 2008 by constant low-flow samplers and using polytetrafluoroethylene (PTFE) membrane filters for particulate (PM₁₀ and PM_2.5 bound) PAHs and pre-cleaned polyurethane foam plugs for gaseous compounds. The other monitored air pollutants were SO₂, PM₁₀, NO₂, CO, and O₃; the meteorological variables were temperature, relative humidity, wind speed, total precipitation, and solar radiation. Benzo[a]pyrene reached a mean concentration of 2.02 ng?m^?3, surpassing the EU annual limit value. The target carcinogenic risks were equal than the health-based guideline level set by USEPA (10^?6) at the studied site, with the cancer risks of eight PAHs reaching senior levels of 9.98?×?10^?7 in PM₁₀ and 1.06?×?10^?6 in air. The applied statistical methods, correlation matrix, cluster analysis, and principal component analysis, were in agreement in the grouping of the PAHs. The groups were formed according to their chemical structure (number of rings), phase distribution, and emission sources. PAH diagnostic ratios were also calculated to evaluate the main emission sources. Diesel vehicular emissions were the major source of PAHs at the studied site. Besides that source, emissions from residential heating and oil refinery were identified to contribute to PAH levels at the respective area. Additionally, principal component regression indicated that SO₂, NO₂, PM₁₀, CO, and solar radiation had positive correlation with PAHs concentrations, while O₃, temperature, relative humidity, and wind speed were negatively correlated.     

Fine Particulate Matter Emissions Inventories: Comparisons of Emissions Estimates with Observations from Recent Field Programs

Abstract

Emissions inventories of fine particulate matter (PM_2.5) were compared with estimates of emissions based on data emerging from U.S. Environment Protection Agency Particulate Matter Supersites and other field programs. Six source categories for PM_2.5 emissions were reviewed: on-road mobile sources, nonroad mobile sources, cooking, biomass combustion, fugitive dust, and stationary sources. Ammonia emissions from all of the source categories were also examined. Regional emissions inventories of PM in the exhaust from on-road and nonroad sources were generally consistent with ambient observations, though uncertainties in some emission factors were twice as large as the emission factors. In contrast, emissions inventories of road dust were up to an order of magnitude larger than ambient observations, and estimated brake wear and tire dust emissions were half as large as ambient observations in urban areas. Although comprehensive nationwide emissions inventories of PM_2.5 from cooking sources and biomass burning are not yet available, observational data in urban areas suggest that cooking sources account for approximately 5–20% of total primary emissions (excluding dust), and biomass burning sources are highly dependent on region. Finally, relatively few observational data were available to assess the accuracy of emission estimates for stationary sources. Overall, the uncertainties in primary emissions for PM_2.5 are substantial. Similar uncertainties exist for ammonia emissions. Because of these uncertainties, the design of PM_2.5 control strategies should be based on inventories that have been refined by a combination of bottom-up and top-down methods.     

Emissions Variability Processor (EMVAP): Design,evaluation, and application

Emissions of pollutants such as SO₂ and NOx from external combustion sources can vary widely depending on fuel sulfur content, load, and transient conditions such as startup, shutdown, and maintenance/malfunction. While monitoring will automatically reflect variability from both emissions and meteorological influences, dispersion modeling has been typically conducted with a single constant peak emission rate. To respond to the need to account for emissions variability in addressing probabilistic 1-hr ambient air quality standards for SO₂ and NO₂, we have developed a statistical technique, the Emissions Variability Processor (EMVAP), which can account for emissions variability in dispersion modeling through Monte Carlo sampling from a specified frequency distribution of emission rates. Based upon initial AERMOD modeling of from 1 to 5 years of actual meteorological conditions, EMVAP is used as a postprocessor to AERMOD to simulate hundreds or even thousands of years of concentration predictions. This procedure uses emissions varied hourly with a Monte Carlo sampling process that is based upon the user-specified emissions distribution, from which a probabilistic estimate can be obtained of the controlling concentration. EMVAP can also accommodate an advanced Tier 2 NO₂ modeling technique that uses a varying ambient ratio method approach to determine the fraction of total oxides of nitrogen that are in the form of nitrogen dioxide. For the case of the 1-hr National Ambient Air Quality Standards (NAAQS, established for SO₂ and NO₂), a “critical value” can be defined as the highest hourly emission rate that would be simulated to satisfy the standard using air dispersion models assuming constant emissions throughout the simulation. The critical value can be used as the starting point for a procedure like EMVAP that evaluates the impact of emissions variability and uses this information to determine an appropriate value to use for a longer term (e.g., 30-day) average emission rate that would still provide protection for the NAAQS under consideration. This paper reports on the design of EMVAP and its evaluation on several field databases that demonstrate that EMVAP produces a suitably modest overestimation of design concentrations. We also provide an example of an EMVAP application that involves a case in which a new emission limitation needs to be considered for a hypothetical emission unit that has infrequent higher-than-normal SO₂ emissions.

ImplicationsEmissions of pollutants from combustion sources can vary widely depending on fuel sulfur content, load, and transient conditions such as startup and shutdown. While monitoring will automatically reflect this variability on measured concentrations, dispersion modeling is typically conducted with a single peak emission rate assumed to occur continuously. To realistically account for emissions variability in addressing probabilistic 1-hr ambient air quality standards for SO₂ and NO₂, the authors have developed a statistical technique, the Emissions Variability Processor (EMVAP), which can account for emissions variability in dispersion modeling through Monte Carlo sampling from a specified frequency distribution of emission rates.     

Trends,temporal and spatial characteristics,and uncertainties in biomass burning emissions in the Pearl River Delta,China

Multi-year inventories of biomass burning emissions were established in the Pearl River Delta (PRD) region for the period 2003–2007 based on the collected activity data and emission factors. The results indicated that emissions of sulfur dioxide (SO₂), nitrogen oxide (NO_x), ammonia (NH₃), methane (CH₄), organic carbon (OC), non-methane volatile organic compounds (NMVOC), carbon monoxide (CO), and fine particulate matter (PM_2.5) presented clear declining trends. Domestic biofuel burning was the major contributor, accounting for more than 60% of the total emissions. The preliminary temporal profiles were established with MODIS fire count information, showing that higher emissions were observed in winter (from November to March) than other seasons. The emissions were spatially allocated into grid cells with a resolution of 3 km × 3  km, using GIS-based land use data as spatial surrogates. Large amount of emissions were observed mostly in the less developed areas in the PRD region. The uncertainties in biomass burning emission estimates were quantified using Monte Carlo simulation; the results showed that there were higher uncertainties in organic carbon (OC) and elemental carbon (EC) emission estimates, ranging from ?71% to 133% and ?70% to 128%, and relatively lower uncertainties in SO₂, NO_x and CO emission estimates. The key uncertainty sources of the developed inventory included emission factors and parameters used for estimating biomass burning amounts.     

Retrospective assessment of air quality management practices in Taiwan

In 1995, Taiwan's Environmental Protection Administration (EPA/TW) instituted a policy of levying emission taxes on polluters in order to combat the rampant national issue of pollution. Since that time, pollution control strategies, tightening exhaust emission standards for industry, improvements in fuel quality, and new stricter vehicle emission standards, etc., have been implemented. This study evaluates the effectiveness of these measures and examines the improvement of Taiwan's air quality. In this paper, we conduct a detailed analysis of change in the concentrations of pollutants (SO₂, NO_x and particulate matter [PM]) between two three-year periods (from 1996 to1998 and from 2000 to 2002). The pollution levels were generally lower in the latter period. Concentrations at 14 EPA/TW stations in central Taiwan were simulated and source apportionment analyses in three of Central Taiwan's largest cities were conducted using a trajectory transfer-coefficient air quality model. Correlation coefficients (r) between simulations and observations for the monthly means of the concentrations of SO₂, NO_x, PM_2.5 and PM₁₀ during the study periods at the 14 stations are 0.56, 0.63, 0.70 and 0.31, respectively. The sulfur control policy greatly reduced SO₂ concentration island-wide, a stringent emission standard put into place for gasoline vehicles reduced NO_x concentration along highways, and an emissions tax placed on construction sites, as well as a regular program for road-dust sweeping, reduced primary particulate matter. Among all of the pollution abatement policies implemented, the most effective method for reducing PM_2.5 concentrations in the three largest cities involved the reduction of fine ammonium sulfate aerosols from point sources (56–63% of net PM_2.5 reduction). The next largest reduction was attributed to a diminishment in primary PM_2.5 emanating from point sources (27–56% of net PM_2.5 reduction). Secondary particulate matter, especially sulfate, was reduced from distances up to 150 km leeward of major pollution point sources such as Taichung Power Plant.     

Estimates of Ground Level TSP,S02 and HCI for a Municipal Waste Incinerator to be Located at Tynes Bay—Bermuda

The computer model Industrial Source Complex Short Term (ISCST) was used to study the stack emissions from a refuse Incinerator proposed for the island of Bermuda. The model predicts that the highest ground level pollutant concentrations will occur near Prospect, 800 m to 1000 m due south of the stack. We installed a portable laboratory and instruments at Prospect to begin making air quality baseline measurements. By comparing the model’s estimates of the incinerator contribution to the background levels measured at the site we predict that stack emissions will not cause an Increase In TSP or SO₂. The incinerator will be a significant source of HCI to Bermuda air with ambient levels approaching air quality guidelines.     

Reducing Opacity by Optimizing Maintenance and Operating Practices

Titus Generating Station, owned and operated by the Metropolitan Edison Company, a subsidiary of the General Public Utilities Corporation, is located in the Reading Air Basin as defined in the Pennsylvania State Law applicable to air resources. Titus Station consists of three boilers which provide steam to generate 240 megawatts of electricity. The station consumes about 600,000 tons of western Pennsylvania bituminous coal each year. Because of its location in an air basin, the operation of Titus Station in compliance with visible and SO₂ emissions standards has been under close scrutiny since 1972. Since that date, Titus Station has operated under various consent orders, variances, and temporary operating permits as Issued by the Pennsylvania Department of Environmental Resources. During this period, efforts were made in all areas of station operation and maintenance to bring Titus Station emissions into compliance, including; Increase of precipitator collector area, revision of coal specifications, closer scrutiny of coal deliveries, implementation of comprehensive precipitator maintenance practices, revision of boiler operating procedures, installation of stack monitoring equipment, and revision of SO₂ emissions regulations. These efforts resulted in continuous compliance with SO₂ regulations and nearly complete compliance with opacity regulations.     

Association of the mutagenicity of airborne particles with the direct emission from combustion processes investigated in Osaka, Japan

The association of the direct-acting mutagenicity of soluble organic fraction of airborne particles toward Salmonella typhimurium YG1024 strain with the direct emission was investigated at a roadside and at a residential area in Osaka, Japan. The direct-acting mutagenicity was evaluated as mutagenic activity per unit volume of ambient air (rev m⁻³) and/or that per airborne particulate weight collected on a filter (rev mg⁻¹). The annual or diurnal changes of the mutagenicity of airborne particles at the residential site showed similar patterns to those of some gaseous pollutants such as NO₂ and SO₂, which were emitted from combustion processes. This result indicates that the mutagenicity is mainly attributable to the primary emissions. From the analysis of the relationship between the wind sector and the mutagenic intensity, rev m⁻³ and rev mg⁻¹ values were strongly affected by the emissions from the fixed sources and from the mobile sources, respectively. The rev m⁻³ value and concentration of 1-nitropyrene (1-NP) in unit per m³ at the roadside were a factor of 2.6 and 2.8 higher than those at the residential site, respectively, but the rev mg⁻¹ value and concentration of 1-NP in unit per mg at the roadside were substantially comparable to those at the residential area. These observations suggest that the characteristics of the airborne particles can be attributed to the automotive emissions even at the suburban area.     

Application of a Lagrangian particle model to assess the impact of harbour,industrial and urban activities on air quality in the Taranto area,Italy

This paper evaluates the relative impact on air quality of harbour emissions, with respect to other emission sources located in the same area. The impact assessment study was conducted in the city of Taranto, Italy. This area was considered as representative of a typical Mediterranean harbour region, where shipping, industries and urban activities co-exist at a short distance, producing an ideal case to study the interaction among these different sources. Chemical and meteorological field campaigns were carried out to provide data to this study. An emission inventory has been developed taking into account industrial sources, traffic, domestic heating, fugitive and harbour emissions. A 3D Lagrangian particle dispersion model (SPRAY) has then been applied to the study area using reconstructed meteorological fields calculated by the diagnostic meteorological model MINERVE. 3D short term hourly concentrations have been computed for both all and specific sources. Industrial activities are found to be the main contributor to SO₂. Industry and traffic emissions are mainly responsible for NO_x simulated concentrations. CO concentrations are found to be mainly related to traffic emissions, while primary PM₁₀ simulated concentrations tend to be linked to industrial and fugitive emissions. Contributions of harbour activities to the seasonal average concentrations of SO₂ and NO_x are predicted to be up to 5 and 30 μg m⁻³, respectively to be compared to a overall peak values of 60 μg m⁻³ for SO₂ and 70 μg m⁻³ for NO_x. At selected urban monitoring stations, SO₂ and NO_x average source contributions are predicted to be both of about 9% from harbour activities, while 87% and 41% respectively of total concentrations are predicted to be of industrial origin.     

Control of Ozone Precursors in a Complex Industrial Terrain by Using Multiscale-Nested Air Quality Models with Fine Spatial Resolution (1 km2)

Abstract

The location of the northeastern Iberian Peninsula (NEIP) in the northwestern Mediterranean basin, the presence of the Pyrenees mountain range (with altitudes >3000 m), and the influence of the Mediterranean Sea and the large valley canalization of Ebro river induce an extremely complicated structure for the dispersion of photochemical pollutants. Air pollution studies in very complex terrains such as the NEIP require high-resolution modeling for resolving the very complex dynamics of flows. To deal with the influence of larger-scale transport, however, high-resolution models have to be nested in larger models to generate appropriate initial and boundary conditions for the finer resolution domains. This article shows the results obtained through the utilization of the MM5-EMICAT2000-CMAQ multiscale-nested air quality model relating the sensitivity regimes for ozone (O₃)-nitrogen oxides (NO_x)-volatile organic compounds (VOCs) in an area of high geographical complexity, like the industrial area of Tarragona, located in the NEIP. The model was applied with fine temporal (one-hour) and spatial resolution (cells of 24 km, 2 km, and 1 km) to represent the chemistry and transport of tropospheric O₃ and other photochemical species with respect to different hypothetical scenarios of emission controls and to quantify the influence of different emission sources in the area. Results indicate that O₃ chemistry in the industrial domain of Tarragona is strongly sensitive to VOCs; the higher percentages of reduction for ground-level O₃ are achieved when reducing by 25% the emissions of industrial VOCs. On the contrary, reductions in the industrial emissions of NO_x contribute to a strong increase in hourly peak levels of O₃. At the same time, the contribution of on-road traffic and biogenic emissions to ground-level O₃ concentrations in the area is negligible with respect to the pervasive weight of industrial sources. This analysis provides an assessment of the effectiveness of different policies for the control of emission of precursors by comparing the modeled results for different scenarios.     

Authors’ Reply

Emissions from oil-fired residential heating equipment can be reduced by improved steady running and cyclic efficiencies. Techniques which reduce the heating demand (thermostat cut-back) or reduce envelope losses (chimney damper) lead to reductions in SO₂ and NO emissions proportional to the fuel saving. Higher savings in CO and particulates result from cyclic modification. Reductions in nozzle size lead to an increase in unit cycle duration, reducing the off-cycle losses, with emissions reduced similarly. Changing the thermostat anticipator yields little reduction in fuel, SO₂ or NO, but significantly reduces CO and particulate emissions, by decreasing the number of cycles. Improved burner performance, with combustion at low excess air, offers the largest fuel savings, with commensurate reductions in SO₂ and NO, and greater reductions in CO and particulates.     

The change in O3, SO2 and NO2 concentrations in Lithuania

Due to the dynamic nature of the atmosphere, substantial amounts of gaseous and particulate pollutants are transported to the areas distant from their sources. In order to determine the regional concentration levels of atmospheric pollutants in Lithuania, concentrations of gaseous O₃, SO₂, NO₂ and other pollutants have been measured at the Preila background station (55°20′ N and 21°00′ E, 5 m a.s.l.) since 1981. The long-term concentration data set enabled us to get temporal trends, both on a seasonal and longer time scale, to identify source areas of pollutants and to relate them to the emission data. Based on the data obtained, the different tendencies in the pollutant concentration changes were revealed. Positive trends for ozone (of 2.9% per year during 1983–2000) and a distinct negative trend for both sulphur dioxide (of 3.8% per year during 1981–2000) and nitrogen dioxide (of 3.8% per year during 1983–2000) were found. The air mass back-trajectory analysis was used to assess the source region of air pollutants transported to Lithuania. The pollutant concentration levels were compared with their emission changes in Europe and Lithuania. The general trends in SO₂ as well as in NO₂ concentrations observed are consistent with changes in SO₂ and NO₂ emissions in Europe and Lithuania.     

Locating the Offender

Abstract

The Coordinating Research Council held its thirteenth Vehicle Emissions Workshop in April 2003, when results of the most recent on-road vehicle emissions research were presented. Ongoing work from researchers who are engaged in improving understanding of the contribution of mobile sources to ambient air quality and emission inventories is summarized here. Participants in the workshop discussed efforts to improve mobile source emission models, the role of on-board diagnostic systems in inspection and maintenance programs, light- and heavy-duty vehicle emissions measurements, on- and off-road emissions measurements, effects of fuels and lubricating oils on emissions, as well as topics for future research.