The impact of CO2 capture in the power and heat sector on the emission of SO2, NOx,particulate matter,volatile organic compounds and NH3 in the European Union

This study quantifies the trade-offs and synergies between climate and air quality policy objectives for the European power and heat (P&H) sector. An overview is presented of the expected performance data of CO₂ capture systems implemented at P&H plants, and the expected emission of key air pollutants, being: SO₂, NO_X, NH₃, volatile organic compounds (VOCs) and particulate matter (PM). The CO₂ capture systems investigated include: post-combustion, oxyfuel combustion and pre-combustion capture.For all capture systems it was found that SO₂, NO_x and PM emissions are expected to be reduced or remain equal per unit of primary energy input compared to power plants without CO₂ capture. Increase in primary energy input as a result of the energy penalty for CO₂ capture may for some technologies and substances result in a net increase of emissions per kWh output. The emission of ammonia may increase by a factor of up to 45 per unit of primary energy input for post-combustion technologies. No data are available about the emission of VOCs from CO₂ capture technologies.A simple model was developed and applied to analyse the impact of CO₂ capture in the European P&H sector on the emission level of key air pollutants in 2030. Four scenarios were developed: one without CO₂ capture and three with one dominantly implemented CO₂ capture system, varying between: post-combustion, oxyfuel combustion and pre-combustion.The results showed a reduction in GHG emissions for the scenarios with CO₂ capture compared to the baseline scenario between 12% and 20% in the EU 27 region in 2030. NO_x emissions were 15% higher in the P&H sector in a scenario with predominantly post-combustion and lower when oxyfuel combustion (?16%) or pre-combustion (?20%) were implemented on a large scale. Large scale implementation of the post-combustion technology in 2030 may also result in significantly higher, i.e. increase by a factor of 28, NH₃ emissions compared to scenarios with other CO₂ capture options or without capture. SO₂ emissions were very low for all scenarios that include large scale implementation of CO₂ capture in 2030, i.e. a reduction varying between 27% and 41%. Particulate Matter emissions were found to be lower in the scenarios with CO₂ capture. The scenario with implementation of the oxyfuel technology showed the lowest PM emissions followed by the scenario with a significant share allocated to pre-combustion, respectively ?59% and ?31%. The scenario with post-combustion capture resulted in PM emissions varying between 35% reduction and 26% increase.     

Toward verifying fossil fuel CO2 emissions with the CMAQ model: Motivation,model description and initial simulation

Motivated by the question of whether and how a state-of-the-art regional chemical transport model (CTM) can facilitate characterization of CO₂ spatiotemporal variability and verify CO₂ fossil-fuel emissions, we for the first time applied the Community Multiscale Air Quality (CMAQ) model to simulate CO₂. This paper presents methods, input data, and initial results for CO₂ simulation using CMAQ over the contiguous United States in October 2007. Modeling experiments have been performed to understand the roles of fossil-fuel emissions, biosphere–atmosphere exchange, and meteorology in regulating the spatial distribution of CO₂ near the surface over the contiguous United States. Three sets of net ecosystem exchange (NEE) fluxes were used as input to assess the impact of uncertainty of NEE on CO₂ concentrations simulated by CMAQ. Observational data from six tall tower sites across the country were used to evaluate model performance. In particular, at the Boulder Atmospheric Observatory (BAO), a tall tower site that receives urban emissions from Denver, CO, the CMAQ model using hourly varying, high-resolution CO₂ fossil-fuel emissions from the Vulcan inventory and CarbonTracker optimized NEE reproduced the observed diurnal profile of CO₂ reasonably well but with a low bias in the early morning. The spatial distribution of CO₂ was found to correlate with NOx, SO₂, and CO, because of their similar fossil-fuel emission sources and common transport processes. These initial results from CMAQ demonstrate the potential of using a regional CTM to help interpret CO₂ observations and understand CO₂ variability in space and time. The ability to simulate a full suite of air pollutants in CMAQ will also facilitate investigations of their use as tracers for CO₂ source attribution. This work serves as a proof of concept and the foundation for more comprehensive examinations of CO₂ spatiotemporal variability and various uncertainties in the future.

Implications: Atmospheric CO₂ has long been modeled and studied on continental to global scales to understand the global carbon cycle. This work demonstrates the potential of modeling and studying CO₂ variability at fine spatiotemporal scales with CMAQ, which has been applied extensively, to study traditionally regulated air pollutants. The abundant observational records of these air pollutants and successful experience in studying and reducing their emissions may be useful for verifying CO₂ emissions. Although there remains much more to further investigate, this work opens up a discussion on whether and how to study CO₂ as an air pollutant.     

Rapid measurement of emissions from military aircraft turbine engines by downstream extractive sampling of aircraft on the ground: Results for C-130 and F-15 aircraft

Aircraft emissions affect air quality on scales from local to global. More than 20% of the jet fuel used in the U.S. is consumed by military aircraft, and emissions from this source are facing increasingly stringent environmental regulations, so improved methods for quickly and accurately determining emissions from existing and new engines are needed. This paper reports results of a study to advance the methods used for detailed characterization of military aircraft emissions, and provides emission factors for two aircraft: the F-15 fighter and the C-130 cargo plane. The measurements involved outdoor ground-level sampling downstream behind operational military aircraft. This permits rapid change-out of the aircraft so that engines can be tested quickly on operational aircraft. Measurements were made at throttle settings from idle to afterburner using a simple extractive probe in the dilute exhaust. Emission factors determined using this approach agree very well with those from the traditional method of extractive sampling at the exhaust exit. Emission factors are reported for CO₂, CO, NO, NO_x, and more than 60 hazardous and/or reactive organic gases. Particle size, mass and composition also were measured and are being reported separately. Comparison of the emissions of nine hazardous air pollutants from these two engines with emissions from nine other aircraft engines is discussed.     

Hazardous air pollutant emissions from gas-fired combustion sources: emissions and the effects of design and fuel type

Air emissions from gas-fired combustion devices such as boilers, process heaters, gas turbines and stationary reciprocating engines contain hazardous air pollutants (HAPs) subjected to consideration under the federal clean air act (CAA). This work presents a recently completed major research project to develop an understanding of HAP emissions from gas-fired boilers and process heaters and new HAP emission factors based on field emission tests of gas-fired external combustion devices used in the petroleum industry. The effect of combustion system design and operating parameters on HAP emissions determined by both field and research tests are discussed. Data from field tests of gas-fired petroleum industry boilers and heaters generally show very low emission levels of organic HAPs. A comparison of the emission data for boilers and process heaters, including units with and without various forms of NOx emission controls, showed no significant difference in organic HAP emission characteristics due to process or burner design. This conclusion is also supported by the results of research tests with different burner designs. Based on field tests of units fired with natural gas and various petroleum industry process gases and research tests in which gas composition was intentionally varied, organic HAP emissions were not determined to be significantly affected by the gas composition. Research data indicate that elevated organic HAP emission levels are found only under extreme operating conditions (starved air or high excess air combustion) associated with poor combustion.     

Emission factors of atmospheric and climatic pollutants from crop residues burning

Biomass burning is a common agricultural practice, because it allows elimination of postharvesting residues; nevertheless, it involves an inefficient combustion process that generates atmospheric pollutants emission, which has implications on health and climate change. This work focuses on the estimation of emission factors (EFs) of PM_2.5, PM₁₀, organic carbon (OC), elemental carbon (EC), carbon monoxide (CO), carbon dioxide (CO₂), and methane (CH₄) of residues from burning alfalfa, barley, beans, cotton, maize, rice, sorghum, and wheat in Mexico. Chemical characteristics of the residues were determined to establish their relationship with EFs, as well as with the modified combustion efficiency (MCE). Essays were carried out in an open combustion chamber with isokinetic sampling, following modified EPA 201-A method. EFs did not present statistical differences among different varieties of the same crop, but were statistically different among different crops, showing that generic values of EFs for all the agricultural residues can introduce significant uncertainties when used for climatic and atmospheric pollutant inventories. EFs of PM_2.5 ranged from 1.19 to 11.30 g kg^?1, and of PM₁₀ from 1.77 to 21.56 g kg^?1. EFs of EC correlated with lignin content, whereas EFs of OC correlated inversely with carbon content. EFs of EC and OC in PM_2.5 ranged from 0.15 to 0.41 g kg^?1 and from 0.33 to 5.29 g kg^?1, respectively, and in PM₁₀, from 0.17 to 0.43 g kg^?1 and from 0.54 to 11.06 g kg^?1. CO₂ represented the largest gaseous emissions volume with 1053.35–1850.82 g kg^?1, whereas the lowest was CH₄ with 1.61–5.59 g kg^?1. CO ranged from 28.85 to 155.71 g kg^?1, correlating inversely with carbon content and MCE. EFs were used to calculate emissions from eight agricultural residues burning in the country during 2016, to know the potential mitigation of climatic and atmospheric pollutants, provided this practice was banned.

Implications: The emission factors of particles, short-lived climatic pollutants, and atmospheric pollutants from the crop residues burning of eight agricultural wastes crops, determined in this study using a standardized method, provides better knowledge of the emissions of those species in Latin America and other developing countries, and can be used as inputs in air quality models and climatic studies. The EFs will allow the development of more accurate inventories of aerosols and gaseous pollutants, which will lead to the design of effective mitigation strategies and planning processes for sustainable agriculture.     

Autonomous mobile platform for monitoring air emissions from industrial and municipal wastewater ponds

Significant amounts of volatile organic compounds and greenhouse gases are generated from wastewater lagoons and tailings ponds in Alberta, Canada. Accurate measurements of these air pollutants and greenhouse gases are needed to support management and regulatory decisions. A mobile platform was developed to measure air emissions from tailings pond in the oil sands region of Alberta. The mobile platform was tested in 2015 in a municipal wastewater treatment lagoon. With a flux chamber and a CO₂/CH₄ sensor on board, the mobile platform was able to measure CO₂ and CH₄ emissions over two days at two different locations in the pond. Flux emission rates of CO₂ and CH₄ that were measured over the study period suggest the presence of aerobic and anaerobic zones in the wastewater treatment lagoon. The study demonstrated the capabilities of the mobile platform in measuring fugitive air emissions and identified the potential for the applications in air and water quality monitoring programs.

Implications: The Mobile Platform demonstrated in this study has the ability to measure greenhouse gas (GHG) emissions from fugitive sources such as municipal wastewater lagoons. This technology can be used to measure emission fluxes from tailings ponds with better detection of spatial and temporal variations of fugitive emissions. Additional air and water sampling equipment could be added to the mobile platform for a broad range of air and water quality studies in the oil sands region of Alberta.     

Emissions Variability Processor (EMVAP): Design,evaluation, and application

Emissions of pollutants such as SO₂ and NOx from external combustion sources can vary widely depending on fuel sulfur content, load, and transient conditions such as startup, shutdown, and maintenance/malfunction. While monitoring will automatically reflect variability from both emissions and meteorological influences, dispersion modeling has been typically conducted with a single constant peak emission rate. To respond to the need to account for emissions variability in addressing probabilistic 1-hr ambient air quality standards for SO₂ and NO₂, we have developed a statistical technique, the Emissions Variability Processor (EMVAP), which can account for emissions variability in dispersion modeling through Monte Carlo sampling from a specified frequency distribution of emission rates. Based upon initial AERMOD modeling of from 1 to 5 years of actual meteorological conditions, EMVAP is used as a postprocessor to AERMOD to simulate hundreds or even thousands of years of concentration predictions. This procedure uses emissions varied hourly with a Monte Carlo sampling process that is based upon the user-specified emissions distribution, from which a probabilistic estimate can be obtained of the controlling concentration. EMVAP can also accommodate an advanced Tier 2 NO₂ modeling technique that uses a varying ambient ratio method approach to determine the fraction of total oxides of nitrogen that are in the form of nitrogen dioxide. For the case of the 1-hr National Ambient Air Quality Standards (NAAQS, established for SO₂ and NO₂), a “critical value” can be defined as the highest hourly emission rate that would be simulated to satisfy the standard using air dispersion models assuming constant emissions throughout the simulation. The critical value can be used as the starting point for a procedure like EMVAP that evaluates the impact of emissions variability and uses this information to determine an appropriate value to use for a longer term (e.g., 30-day) average emission rate that would still provide protection for the NAAQS under consideration. This paper reports on the design of EMVAP and its evaluation on several field databases that demonstrate that EMVAP produces a suitably modest overestimation of design concentrations. We also provide an example of an EMVAP application that involves a case in which a new emission limitation needs to be considered for a hypothetical emission unit that has infrequent higher-than-normal SO₂ emissions.

ImplicationsEmissions of pollutants from combustion sources can vary widely depending on fuel sulfur content, load, and transient conditions such as startup and shutdown. While monitoring will automatically reflect this variability on measured concentrations, dispersion modeling is typically conducted with a single peak emission rate assumed to occur continuously. To realistically account for emissions variability in addressing probabilistic 1-hr ambient air quality standards for SO₂ and NO₂, the authors have developed a statistical technique, the Emissions Variability Processor (EMVAP), which can account for emissions variability in dispersion modeling through Monte Carlo sampling from a specified frequency distribution of emission rates.     

Environmental Impact of Residential Wood Combustion Emissions and its Implications

Currently available information suggests a substantial environmental impact from residential wood combustion emissions. Air pollution from this source is widespread and increasing. Current ambient measurements, surveys, and model predictions indicate winter respirable (<2 μm) emissions from residential wood combustion can easily exceed all other sources. Both the chemical potency and deliverability of the emissions from this source are of concern. The emissions are almost entirely in the inhalable size range and contain toxic and priority pollutants, carcinogens, co-carcinogens, cilia toxic, mucus coagulating agents, and other respiratory irritants such as phenols, aldehydes, etc. This source is contributing substantially to the nonattainment of current particulate, carbon monoxide, and hydrocarbon ambient air quality standards and will almost certainly have a significant impact on potential future standards such as inhalable particulates, visibility, and other chemically specific standards. Emission from this growing source is likely to require additional expenditures by industry for air pollution control equipment in nonattainment areas.     

Trend of vehicle emission levels until 2020 – Prognosis based on current vehicle measurements and future emission legislation

The paper describes the incorporation of actual emission measurements and future emission standards into the emission model ‘NEMO’ (Network Emission Model). This model is then applied to make predictions on vehicle emission levels on basis of the Austrian fleet composition until 2020. The output is compared to the results based on the most common emission tool for the calculation of vehicle emissions in Central Europe – the recent version (2.1) of the ‘Handbook Emission Factors for Road Transport’. The discussion is focused on NO_x and particulate matter (PM), since these pollutants are considered to be the most critical for the local air quality level.The NO_x emission levels of recent modern diesel vehicle generations observed in several real world driving conditions were observed to be clearly higher than demanded in the type approval procedure. Due to the growing number of modern diesel engine concepts equipped with coated catalytic exhaust after treatment, the fraction of NO₂ of the total tailpipe NO_x emissions is predicted to continue to increase in the next few years. Bearing in mind the upcoming tightening of the NO₂ air quality limits and the steady increase of traffic volumes, excesses of the NO₂ air quality limits at roadside locations have to be expected to an increasing extent for the beginning of the next decade. The issue of particle emissions originated from the diesel engine combustion process can be regarded as being technically solved due to the extensive introduction of diesel particle filters in the vehicle fleet if these systems will prove a high efficiency over the entire vehicle life in real world operation conditions. However, PM emissions from road transport will continue to be in the focus of public attention due to particle emissions caused by dust re-suspension and abrasion processes.     

Current and future emission estimates of exhaust gases and particles from shipping at the largest port in Korea

The emissions of exhaust gases (NO _x , SO₂, VOCs, and CO₂) and particles (e.g., PM) from ships traversing Busan Port in Korea were estimated over three different years (the years 2006, 2008, and 2009). This analysis was performed according to the ship operational modes (“at sea,” “maneuvering,” and “in port”) and ship types based on an activity-based method. The ship emissions for current (base year 2009) and future scenarios (years 2020 and 2050) were also compared. The annual emissions of SO₂, VOCs, PM, and CO₂ were highest (9.6?×?10³, 374, 1.2?×?10³, and 5.6?×?10⁵ ton year^?1, respectively) in 2008. In contrast, the annual NO _x emissions were highest (11.7?×?10³ ton year^?1) in 2006 due mainly to the high NO _x emission factor. The emissions of air pollutants for each ship operational mode differed considerably, with the largest emission observed in “in port” mode. In addition, the largest fraction (approximately 45–67 %) of the emissions of all air pollutants during the study period was emitted from container ships. The future ship emissions of most pollutants (except for SO₂ and PM) in 2020 and 2050 are estimated to be 1.4–1.8 and 4.7–6.1 times higher than those in 2009 (base year), respectively.     

Characteristics of gaseous pollutants from biofuel-stoves in rural China

The research team analyzed the emission characteristics of gaseous pollutants, including volatile organic compounds (VOCs), from biomass combustion in improved stoves in rural China. The research included measurements from five biofuels and two stove types in the months of January, April, and September. The measurements were conducted according to U.S. EPA Method 25 using a collection system with a cooling device and two-level filters. CO, CO₂, NO_x, CH₄ and THC analyzers were used for in-field, real-time emission measurements. The emission data indicate that gaseous pollutants were emitted at higher concentrations in the early combustion stage and lower concentrations in the later stage. CH₄ and THC, as well as CO and CO₂, presented positive relationships during the whole entire combustion process for all tests. The chemical profiles of flue gas samples were analyzed by GC/MS and GC/FID/ECD. Aromatics, carbonyls, and alkenes & alkynes dominated the VOC emissions, respectively accounting for 37%, 33%, and 23% of total VOC emissions by volume. Benzene was the most abundant VOC species, consisting of 17.3 ± 8.1% of VOCs, followed by propylene (11.3 ± 3.5%), acetone (10.8 ± 8.2%), toluene (7.3 ± 5.7%) and acetaldehyde (6.5 ± 7.3%). Carbon mass balance approach was applied to calculate CO, CO₂, CH₄, NO_x, and VOC species emission factors. This analysis includes a discussion of the differences among VOC emission factors of different biofuel-stove combinations.     

Carbon dioxide and methane emissions from the scale model of open dairy lots

To investigate the impacts of major factors on carbon loss via gaseous emissions, carbon dioxide (CO₂) and methane (CH₄) emissions from the ground of open dairy lots were tested by a scale model experiment at various air temperatures (15, 25, and 35 °C), surface velocities (0.4, 0.7, 1.0, and 1.2 m sec^?1), and floor types (unpaved soil floor and brick-paved floor) in controlled laboratory conditions using the wind tunnel method. Generally, CO₂ and CH₄ emissions were significantly enhanced with the increase of air temperature and velocity (P < 0.05). Floor type had different effects on the CO₂ and CH₄ emissions, which were also affected by air temperature and soil characteristics of the floor. Although different patterns were observed on CH₄ emission from the soil and brick floors at different air temperature-velocity combinations, statistical analysis showed no significant difference in CH₄ emissions from different floors (P > 0.05). For CO₂, similar emissions were found from the soil and brick floors at 15 and 25 °C, whereas higher rates were detected from the brick floor at 35 °C (P < 0.05). Results showed that CH₄ emission from the scale model was exponentially related to CO₂ flux, which might be helpful in CH₄ emission estimation from manure management.

Implications: Gaseous emissions from the open lots are largely dependent on outdoor climate, floor systems, and management practices, which are quite different from those indoors. This study assessed the effects of floor types and air velocities on CO₂ and CH₄ emissions from the open dairy lots at various temperatures by a wind tunnel. It provided some valuable information for decision-making and further studies on gaseous emissions from open lots.     

Needed: A National R&D Effort To Develop Individual Air Pollution Monitor Instrumentation

The results from the regional air quality analysis for the Four Corners Study are discussed in this paper. This study was one of five regional studies conducted for the National Commission on Air Quality. Potential regional air quality impacts were evaluated through the year 1995 for alternative energy scenarios under current and alternative regulatory policies. The alternative regulatory policies include emission fees, technology standards, emission ceilings, and prevention of significant deterioration class elimination. The alternatives were compared in terms of their impacts on regional visibility and on the ambient concentrations of SO₂, SO₄, and primary fine particulates. The fate of the pollutants was estimated. The alternative regulatory policies were quite different with respect to their control of SO_X emissions and their impacts on regional visibility. Sources located outside of the study region were estimated to have a major impact on regional air quality within the study region.     

Total life cycle emissions of post-Panamax containerships powered by conventional fuel or natural gas

This study proposes an easy-to-apply method, the Total Life Cycle Emission Model (TLCEM), to calculate the total emissions from shipping and help ship management groups assess the impact on emissions caused by their capital investment or operation decisions. Using TLCEM, we present the total emissions of air pollutants and greenhouse gases (GHGs) during the 25-yr life cycle of 10 post-Panamax containerships under slow steaming conditions. The life cycle consists of steel production, shipbuilding, crude oil extraction and transportation, fuel refining, bunkering, and ship operation. We calculate total emissions from containerships and compare the effect of emission reduction by using various fuels. The results can be used to differentiate the emissions from various processes and to assess the effectiveness of various reduction approaches. Critical pollutants and GHGs emitted from each process are calculated. If the containerships use heavy fuel oil (HFO), emissions of CO₂ total 2.79 million tonnes (Mt), accounting for 95.37% of total emissions, followed by NO_x and SO_x emissions,which account for 2.25% and 1.30%, respectively.The most significant emissions are from the operation of the ship and originate from the main engine (ME).When fuel is switched to 100% natural gas (NG), SO_x, PM₁₀, and CO₂ emissions show remarkable reductions of 98.60%, 99.06%, and 21.70%, respectively. Determining the emission factor of each process is critical for estimating the total emissions. The estimated emission factors were compared with the values adopted by the International Maritime Organization (IMO).The proposed TLCEM may contribute to more accurate estimates of total life cycle emissions from global shipping.

Implications: We propose a total life cycle emissions model for 10 post-Panamax container ships. Using heavy fuel oil, emissions of CO₂ total 2.79 Mt, accounting for approximately 95% of emissions, followed by NO_x and SO_x emissions. Using 100% natural gas, SO_x, PM₁₀, and CO₂ emissions reduce by 98.6%, 99.1%, and 21.7%, respectively. NO_x emissions increase by 1.14% when running a dual fuel engine at low load in natural gas mode.     

Potential Air Emission Impacts of Cellulosic Ethanol Production at Seven Demonstration Refineries in the United States

Abstract

This paper reports on the estimated potential air emissions, as found in air permits and supporting documentation, for seven of the first group of precommercial or “demonstration” cellulosic ethanol refineries (7CEDF) currently operating or planning to operate in the United States in the near future. These seven refineries are designed to produce from 330,000 to 100 million gal of ethanol per year. The overall average estimated air emission rates for criteria, hazardous, and greenhouse gas pollutants at the 7CEDF are shown here in terms of tons per year and pounds per gallon of ethanol produced. Water use rates estimated for the cellulosic ethanol refineries are also noted. The air emissions are then compared with similar estimates from a U.S. cellulosic ethanol pilot plant, a commercial Canadian cellulosic ethanol refinery, four commercial U.S. corn ethanol refineries, and U.S. petroleum refineries producing gasoline. The U.S. Environmental Protection Agency (EPA) air pollution rules that may apply to cellulosic ethanol refineries are also discussed. Using the lowest estimated emission rates from these cellulosic ethanol demonstration facilities to project air emissions, EPA’s major source thresholds for criteria and hazardous air pollutants might not be exceeded by cellulosic ethanol refineries that produce as high as 25 million gal per year of ethanol (95 ML). Emissions are expected to decrease at cellulosic ethanol refineries as the process matures and becomes more commercially viable.     

The influence of air–fuel ratio on engine performance and pollutant emission of an SI engine using ethanol–gasoline-blended fuels

Ethanol–gasoline-blended fuel was tested in a conventional engine under various air–fuel equivalence ratios (λ) for its performance and emissions. The amount of fuel injection was adjusted manually by an open-loop control system using a CONSULT controller. It was found that without changing throttle opening and injection strategy, λ could be extended to a leaner condition as ethanol content increased. The results of engine performance tests showed that torque output would increase slightly at small throttle valve opening when ethanol–gasoline-blended fuel was used. It was also shown that CO and HC emissions were reduced with the increase of ethanol content in the blended fuel, which resulted from oxygen enrichment. At an air–fuel equivalence ratio slightly larger than one, the smallest amounts of CO and HC and the largest amounts of CO₂ resulted. It was noted that under the lean combustion condition, CO₂ emission was controlled by air–fuel equivalence ratio; while under the rich combustion condition, CO₂ emission is offset by CO emission. It was also found that CO₂ emission per unit horse power output for blended fuel was similar or less than that for gasoline fuel. From the experimental data, the optimal ethanol content in the gasoline and air–fuel equivalence ratio in terms of engine performance and air pollution was found.     

Analysis and modelling of the pollutant emissions from European cars regarding the driving characteristics and test cycles

Within the European research project ARTEMIS, significant works have been conducted to analyse the hot emissions of pollutant from the passenger cars regarding the driving cycles and to propose modelling approaches taking into account large but heterogeneous datasets recorded in Europe. The review and analysis of a large range of test cycles enabled first the building-up of a set of contrasted cycles specifically designed for characterizing the influence of the driving conditions. These cycles were used for the measurement of the pollutants emission rates from nine passenger cars on a chassis dynamometer.Emissions measured on 30 vehicles tested on cycles adapted to their motorization (i.e., cycles for high- or low-powered cars, inducing thus a significant difference in the dynamic) were also considered for analysing the influence of the cycles and of the kinematic parameters on the hot emission rates of the regulated pollutants (CO, HC, NO_x, CO₂, PM). An analyses of variance demonstrated the preponderance of the driving type (urban, rural road, motorway), of the vehicle category (fuel, emission standard) and emitting status (high/normal emitter) and thus the pertinence of analysing and modelling separately the corresponding emissions. It also demonstrated that Urban driving led systematically to high diesel emission rates and to high CO₂, HC and NO_x emissions from petrol cars. Congested driving implied high CO₂ (diesel and petrol) and high diesel NO_x emission. On motorway, the very high speeds generated high CO₂, while unsteady speeds induced diesel NO_x and petrol CO over-emissions. A search for pertinent kinematic parameters showed that urban diesel emissions were mostly sensitive to stops and speed parameters, while petrol emissions were rather sensitive to acceleration parameters. On the motorway, diesel NO_x and CO₂ emissions rates increased with the speed variability and occurrence of high speeds, while CO₂ and CO over-emission from petrol cars were linked to the occurrence of strong acceleration at high speeds.A modelling approach based on partial least square regression was tested, which demonstrates its ability to discriminate satisfactorily the emissions according to dynamic related parameters and in particular when considering the two-dimensionnal distribution of instantaneous speed and acceleration.Finally, a strategy was proposed to analyse the large but heterogeneous set of hot emission data collected within the ARTEMIS project. The approach consisted in analysing the similarity of the numerous cycles as regards their kinematic, grouping them into reference test patterns through an automatic clustering, and then computing reference emissions for these patterns. These principles enabled the development of a method to compute the emissions at a low spatial scale, i.e. the so-called traffic situation approach, which was implemented in the European Artemis model for estimating the cars’ pollutant emissions.     

Transport impacts on atmosphere and climate: Shipping

Emissions of exhaust gases and particles from oceangoing ships are a significant and growing contributor to the total emissions from the transportation sector. We present an assessment of the contribution of gaseous and particulate emissions from oceangoing shipping to anthropogenic emissions and air quality. We also assess the degradation in human health and climate change created by these emissions. Regulating ship emissions requires comprehensive knowledge of current fuel consumption and emissions, understanding of their impact on atmospheric composition and climate, and projections of potential future evolutions and mitigation options. Nearly 70% of ship emissions occur within 400 km of coastlines, causing air quality problems through the formation of ground-level ozone, sulphur emissions and particulate matter in coastal areas and harbours with heavy traffic. Furthermore, ozone and aerosol precursor emissions as well as their derivative species from ships may be transported in the atmosphere over several hundreds of kilometres, and thus contribute to air quality problems further inland, even though they are emitted at sea. In addition, ship emissions impact climate. Recent studies indicate that the cooling due to altered clouds far outweighs the warming effects from greenhouse gases such as carbon dioxide (CO₂) or ozone from shipping, overall causing a negative present-day radiative forcing (RF). Current efforts to reduce sulphur and other pollutants from shipping may modify this. However, given the short residence time of sulphate compared to CO₂, the climate response from sulphate is of the order decades while that of CO₂ is centuries. The climatic trade-off between positive and negative radiative forcing is still a topic of scientific research, but from what is currently known, a simple cancellation of global mean forcing components is potentially inappropriate and a more comprehensive assessment metric is required. The CO₂ equivalent emissions using the global temperature change potential (GTP) metric indicate that after 50 years the net global mean effect of current emissions is close to zero through cancellation of warming by CO₂ and cooling by sulphate and nitrogen oxides.     

Local Arctic air pollution: Sources and impacts

Local emissions of Arctic air pollutants and their impacts on climate, ecosystems and health are poorly understood. Future increases due to Arctic warming or economic drivers may put additional pressures on the fragile Arctic environment already affected by mid-latitude air pollution. Aircraft data were collected, for the first time, downwind of shipping and petroleum extraction facilities in the European Arctic. Data analysis reveals discrepancies compared to commonly used emission inventories, highlighting missing emissions (e.g. drilling rigs) and the intermittent nature of certain emissions (e.g. flaring, shipping). Present-day shipping/petroleum extraction emissions already appear to be impacting pollutant (ozone, aerosols) levels along the Norwegian coast and are estimated to cool and warm the Arctic climate, respectively. Future increases in shipping may lead to short-term (long-term) warming (cooling) due to reduced sulphur (CO₂) emissions, and be detrimental to regional air quality (ozone). Further quantification of local Arctic emission impacts is needed.     

Codependencies of Reactive Air Toxic and Criteria Pollutants on Emission Reductions

Abstract

It is important to understand the effects of emission controls on concentrations of ozone, fine particulate matter (PM_2.5), and hazardous air pollutants (HAPs) simultaneously, to evaluate the full range of health, ecosystem, and economic effects. Until recently, the capability to simultaneously evaluate interrelated atmospheric pollutants (“one atmosphere” analysis) was unavailable to air quality managers. In this work, we use an air quality model to examine the potential effect of three emission reductions on concentrations of ozone, PM_2.5, and four important HAPs (formaldehyde, acetaldehyde, acrolein, and benzene) over a domain centered on Philadelphia for 12-day episodes in July and January 2001. Although NO_x controls are predicted to benefit PM_2.5 concentrations and sometimes benefit ozone, they have only a small effect on formaldehyde, slightly increase acetaldehyde and acrolein, and have no effect on benzene in the July episode. Concentrations of all pollutants except benzene increase slightly with NO_x controls in the January simulation. Volatile organic compound controls alone are found to have a small effect on ozone and PM_2.5, a less than linear effect on decreasing aldehydes, and an approximately linear effect on acrolein and benzene in summer, but a slightly larger than linear effect on aldehydes and acrolein in winter. These simulations indicate the difficulty in assessing how toxic air pollutants might respond to emission reductions aimed at decreasing criteria pollutants such as ozone and PM_2.5.