Optimization of the O3/H2O2 process with response surface methodology for pretreatment of mother liquor of gas field wastewater

• Real ML-GFW with high salinity and high organics was degraded by O₃/H₂O₂ process. • Successful optimization of operation conditions was attained using RSM based on CCD. • Single-factor experiments in advance ensured optimal experimental conditions. • The satisfactory removal efficiency of TOC was achieved in spite of high salinity. • The initial pH plays the most significant role in the degradation of ML-GFW. The present study reports the use of the O₃/H₂O₂ process in the pretreatment of the mother liquor of gas field wastewater (ML-GFW), obtained from the multi-effect distillation treatment of the gas field wastewater. The range of optimal operation conditions was obtained by single-factor experiments. Response surface methodology (RSM) based on the central composite design (CCD) was used for the optimization procedure. A regression model with Total organic carbon (TOC) removal efficiency as the response value was established (R² = 0.9865). The three key factors were arranged according to their significance as: pH>H₂O₂ dosage>ozone flow rate. The model predicted that the best operation conditions could be obtained at a pH of 10.9, an ozone flow rate of 0.8 L/min, and H₂O₂ dosage of 6.2 mL. The dosing ratio of ozone was calculated to be 9.84 mg O₃/mg TOC. The maximum removal efficiency predicted was 75.9%, while the measured value was 72.3%. The relative deviation was found to be in an acceptable range. The ozone utilization and free radical quenching experiments showed that the addition of H₂O₂ promoted the decomposition of ozone to produce hydroxyl radicals (·OH). This also improved the ozone utilization efficiency. Gas chromatography-mass spectrometry (GC-MS) analysis showed that most of the organic matters in ML-GFW were degraded, while some residuals needed further treatment. This study provided the data and the necessary technical supports for further research on the treatment of ML-GFW.     

Rapid and long-effective removal of broad-spectrum pollutants from aqueous system by ZVI/oxidants

• The coupling of oxidants with ZVI overcome the impedance of ZVI passive layer. • ZVI/oxidants system achieved fast and long-effective removal of contaminants. • Multiple mechanisms are involved in contaminants removal by ZVI/oxidant system. • ZVI/Oxidants did not change the reducing property of ORP in the fixed-bed system. Zero-valent iron (ZVI) technology has recently gained significant interest in the efficient sequestration of a wide variety of contaminants. However, surface passivation of ZVI because of its intrinsic passive layer would lead to the inferior reactivity of ZVI and its lower efficacy in contaminant removal. Therefore, to activate the ZVI surface cheaply, continuously, and efficiently is an important challenge that ZVI technology must overcome before its wide-scale application. To date, several physical and chemical approaches have been extensively applied to increase the reactivity of the ZVI surface toward the elimination of broad-spectrum pollutants. Nevertheless, these techniques have several limitations such as low efficacy, narrow working pH, eco-toxicity, and high installation cost. The objective of this mini-review paper is to identify the critical role of oxygen in determining the reactivity of ZVI toward contaminant removal. Subsequently, the effect of three typical oxidants (H₂O₂, KMnO₄, and NaClO) on broad-spectrum contaminants removal by ZVI has been documented and discussed. The reaction mechanism and sequestration efficacies of the ZVI/oxidant system were evaluated and reviewed. The technical basis of the ZVI/oxidant approach is based on the half-reaction of the cathodic reduction of the oxidants. The oxidants commonly used in the water treatment industry, i.e., NaClO, O₃, and H₂O₂, can be served as an ideal coupling electron receptor. With the combination of these oxidants, the surface corrosion of ZVI can be continuously driven. The ZVI/oxidants technology has been compared with other conventional technologies and conclusions have been drawn.     

Toward better understanding vacuum ultraviolet–iodide induced photolysis via hydrogen peroxide formation,iodine species change,and difluoroacetic acid degradation

• UV/VUV/I^– induces substantial H₂O₂ and IO₃^– formation, but UV/I^– does not. • Increasing DO level in water enhances H₂O₂ and iodate productions. • Increasing pH decreases H₂O₂ and iodate formation and also photo-oxidation. • The redox potentials of UV/VUV/I^– and UV/VUV changes with pH changes. • The treatability of the UV/VUV/I^– process was stronger than UV/VUV at pH 11.0. Recently, a photochemical process induced by ultraviolet (UV), vacuum UV (VUV), and iodide (I^–) has gained attention for its robust potential for contaminant degradation. However, the mechanisms behind this process remain unclear because both oxidizing and reducing reactants are likely generated. To better understand this process, this study examined the evolutions of hydrogen peroxide (H₂O₂) and iodine species (i.e., iodide, iodate, and triiodide) during the UV/VUV/I^– process under varying pH and dissolved oxygen (DO) conditions. Results show that increasing DO in water enhanced H₂O₂ and iodate production, suggesting that high DO favors the formation of oxidizing species. In contrast, increasing pH (from 6.0 to 11.0) resulted in lower H₂O₂ and iodate formation, indicating that there was a decrease of oxidative capacity for the UV/VUV/I^– process. In addition, difluoroacetic acid (DFAA) was used as an exemplar contaminant to verify above observations. Although its degradation kinetics did not follow a constant trend as pH increases, the relative importance of mineralization appeared declining, suggesting that there was a redox transition from an oxidizing environment to a reducing environment as pH rises. The treatability of the UV/VUV/I^– process was stronger than UV/VUV under pH of 11.0, while UV/VUV process presented a better performance at pH lower than 11.0.     

Evaluation of the technoeconomic feasibility of electrochemical hydrogen peroxide production for decentralized water treatment

• Gas diffusion electrode (GDE) is a suitable setup for practical water treatment. • Electrochemical H₂O₂ production is an economically competitive technology. • High current efficiency of H₂O₂ production was obtained with GDE at 5–400 mA/cm². • GDE maintained high stability for H₂O₂ production for ~1000 h. • Electro-generation of H₂O₂ enhances ibuprofen removal in an E-peroxone process. This study evaluated the feasibility of electrochemical hydrogen peroxide (H₂O₂) production with gas diffusion electrode (GDE) for decentralized water treatment. Carbon black-polytetrafluoroethylene GDEs were prepared and tested in a continuous flow electrochemical cell for H₂O₂ production from oxygen reduction. Results showed that because of the effective oxygen transfer in GDEs, the electrode maintained high apparent current efficiencies (ACEs,>80%) for H₂O₂ production over a wide current density range of 5–400 mA/cm², and H₂O₂ production rates as high as ~202 mg/h/cm² could be obtained. Long-term stability test showed that the GDE maintained high ACEs (>85%) and low energy consumption (<10 kWh/kg H₂O₂) for H₂O₂ production for 42 d (~1000 h). However, the ACEs then decreased to ~70% in the following 4 days because water flooding of GDE pores considerably impeded oxygen transport at the late stage of the trial. Based on an electrode lifetime of 46 days, the overall cost for H₂O₂ production was estimated to be ~0.88 $/kg H₂O₂, including an electricity cost of 0.61 $/kg and an electrode capital cost of 0.27 $/kg. With a 9 cm² GDE and 40 mA/cm² current density, ~2–4 mg/L of H₂O₂ could be produced on site for the electro-peroxone treatment of a 1.2 m³/d groundwater flow, which considerably enhanced ibuprofen abatement compared with ozonation alone (~43%–59% vs. 7%). These findings suggest that electrochemical H₂O₂ production with GDEs holds great promise for the development of compact treatment technologies for decentralized water treatment at a household and community level.     

Zero-valent manganese nanoparticles coupled with different strong oxidants for thallium removal from wastewater

• Nano zero-valent manganese (nZVMn, Mn⁰) is synthesized via borohydrides reduction. • Mn⁰ combined with persulfate/hypochlorite is effective for Tl removal at pH 6-12. • Mn⁰ can activate persulfate to form hydroxyl and sulfate radicals. • Oxidation-induced precipitation and surface complexation contribute to Tl removal. • Combined Mn⁰-oxidants process is promising in the environmental field. Nano zero-valent manganese (nZVMn, Mn⁰) was prepared through a borohydride reduction method and coupled with different oxidants (persulfate (S₂O₈²⁻), hypochlorite (ClO⁻), or hydrogen peroxide (H₂O₂)) to remove thallium (Tl) from wastewater. The surface of Mn⁰ was readily oxidized to form a core-shell composite (MnO_x@Mn⁰), which consists of Mn⁰ as the inner core and MnO_x (MnO, Mn₂O₃, and Mn₃O₄) as the outer layer. When Mn⁰ was added alone, effective Tl(I) removal was achieved at high pH levels (>12). The Mn⁰-H₂O₂ system was only effective in Tl(I) removal at high pH (>12), while the Mn⁰-S₂O₈²⁻ or Mn⁰-ClO⁻ system had excellent Tl(I) removal (>96%) over a broad pH range (4–12). The Mn⁰-S₂O₈²⁻ oxidation system provided the best resistance to interference from an external organic matrix. The isotherm of Tl(I) removal through the Mn⁰-S₂O₈²⁻ system followed the Freundlich model. The Mn⁰ nanomaterials can activate persulfate to produce sulfate radicals and hydroxyl radicals. Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy suggested that oxidation-induced precipitation, surface adsorption, and electrostatic attraction are the main mechanisms for Tl(I) removal resulting from the combination of Mn⁰ and oxidants. Mn⁰ coupled with S₂O₈²⁻/ClO⁻ is a novel and effective technique for Tl(I) removal, and its application in other fields is worthy of further investigation.     

Enhanced catalytic oxidation of 2,4-dichlorophenol via singlet oxygen dominated peroxymonosulfate activation on CoOOH@Bi2O3 composite

• Bi₂O₃ cannot directly activate PMS. • Bi₂O₃ loading increased the specific surface area and conductivity of CoOOH. • Larger specific surface area provided more active sites for PMS activation. • Faster electron transfer rate promoted the generation of reactive oxygen species. • ¹O₂ was identified as dominant ROS in the CoOOH@Bi₂O₃/PMS system. Cobalt oxyhydroxide (CoOOH) has been turned out to be a high-efficiency catalyst for peroxymonosulfate (PMS) activation. In this study, CoOOH was loaded on bismuth oxide (Bi₂O₃) using a facile chemical precipitation process to improve its catalytic activity and stability. The result showed that the catalytic performance on the 2,4-dichlorophenol (2,4-DCP) degradation was significantly enhanced with only 11 wt% Bi₂O₃ loading. The degradation rate in the CoOOH@Bi₂O₃/PMS system (0.2011 min⁻¹) was nearly 6.0 times higher than that in the CoOOH/PMS system (0.0337 min⁻¹). Furthermore, CoOOH@Bi₂O₃ displayed better stability with less Co ions leaching (16.4% lower than CoOOH) in the PMS system. These phenomena were attributed to the Bi₂O₃ loading which significantly increased the conductivity and specific surface area of the CoOOH@Bi₂O₃ composite. Faster electron transfer facilitated the redox reaction of Co (III) / Co (II) and thus was more favorable for reactive oxygen species (ROS) generation. Meanwhile, larger specific surface area furnished more active sites for PMS activation. More importantly, there were both non-radical (¹O₂) and radicals (SO₄⁻•, O₂⁻•, and OH•) in the CoOOH@Bi₂O₃/PMS system and ¹O₂ was the dominant one. In general, this study provided a simple and practical strategy to enhance the catalytic activity and stability of cobalt oxyhydroxide in the PMS system.     

Enhanced triallyl isocyanurate (TAIC) degradation through application of an O3/UV process: Performance optimization and degradation pathways

• UV/O₃ process had higher TAIC mineralization rate than O₃ process. • Four possible degradation pathways were proposed during TAIC degradation. • pH impacted oxidation processes with pH of 9 achieving maximum efficiency. • CO₃^2– negatively impacted TAIC degradation while HCO₃^– not. • Cl^– can be radicals scavenger only at high concentration (over 500 mg/L Cl^–). Triallyl isocyanurate (TAIC, C₁₂H₁₅N₃O₃) has featured in wastewater treatment as a refractory organic compound due to the significant production capability and negative environmental impact. TAIC degradation was enhanced when an ozone(O₃)/ultraviolet(UV) process was applied compared with the application of an independent O₃ process. Although 99% of TAIC could be degraded in 5 min during both processes, the O₃/UV process had a 70%mineralization rate that was much higher than that of the independent O₃ process (9%) in 30 min. Four possible degradation pathways were proposed based on the organic compounds of intermediate products identified during TAIC degradation through the application of independent O₃ and O₃/UV processes. pH impacted both the direct and indirect oxidation processes. Acidic and alkaline conditions preferred direct and indirect reactions respectively, with a pH of 9 achieving maximum Total Organic Carbon (TOC) removal. Both CO₃^2– and HCO₃^– decreased TOC removal, however only CO₃^2– negatively impacted TAIC degradation. Effects of Cl^– as a radical scavenger became more marked only at high concentrations (over 500 mg/L Cl^–). Particulate and suspended matter could hinder the transmission of ultraviolet light and reduce the production of HO· accordingly.     

Enhanced carbon tetrachloride degradation by hydroxylamine in ferrous ion activated calcium peroxide in the presence of formic acid

• Complete CT degradation was achieved by employing HA to CP/Fe(II)/FA process. • Quantitative detection of Fe(II) regeneration and HO• production was investigated. • Benzoic acid outcompeted FA for the reaction with HO•. • CO₂•⁻ was the dominant reductive radical for CT removal. • Effects of solution matrix on CT removal were conducted. Hydroxyl radicals (HO•) show low reactivity with perchlorinated hydrocarbons, such as carbon tetrachloride (CT), in conventional Fenton reactions, therefore, the generation of reductive radicals has attracted increasing attention. This study investigated the enhancement of CT degradation by the synergistic effects of hydroxylamine (HA) and formic acid (FA) (initial [CT] = 0.13 mmol/L) in a Fe(II) activated calcium peroxide (CP) Fenton process. CT degradation increased from 56.6% to 99.9% with the addition of 0.78 mmol/L HA to the CP/Fe(II)/FA/CT process in a molar ratio of 12/6/12/1. The results also showed that the presence of HA enhanced the regeneration of Fe(II) from Fe(III), and the production of HO• increased one-fold when employing benzoic acid as the HO• probe. Additionally, FA slightly improves the production of HO•. A study of the mechanism confirmed that the carbon dioxide radical (CO₂•⁻), a strong reductant generated by the reaction between FA and HO•, was the dominant radical responsible for CT degradation. Almost complete CT dechlorination was achieved in the process. The presence of humic acid and chloride ion slightly decreased CT removal, while high doses of bicarbonate and high pH inhibited CT degradation. This study helps us to better understand the synergistic roles of FA and HA for HO• and CO₂•⁻ generation and the removal of perchlorinated hydrocarbons in modified Fenton systems.     

Degradation of refractory organics in concentrated leachate by the Fenton process: Central composite design for process optimization

• 90% total COD, 95.3% inert COD and 97.2% UV₂₅₄ were removed. • High R² values (over 95%) for all responses were obtained with CCD. • Operational cost was calculated to be 0.238 €/g COD_removed for total COD removal. • Fenton oxidation was highly-efficient method for inert COD removal. • BOD₅/COD ratio of leachate concentrate raised from 0.04 to 0.4. The primary aim of this study is inert COD removal from leachate nanofiltration concentrate because of its high concentration of resistant organic pollutants. Within this framework, this study focuses on the treatability of leachate nanofiltration concentrate through Fenton oxidation and optimization of process parameters to reach the maximum pollutant removal by using response surface methodology (RSM). Initial pH, Fe²⁺ concentration, H₂O₂/Fe²⁺ molar ratio and oxidation time are selected as the independent variables, whereas total COD, color, inert COD and UV₂₅₄ removal are selected as the responses. According to the ANOVA results, the R² values of all responses are found to be over 95%. Under the optimum conditions determined by the model (pH: 3.99, Fe²⁺: 150 mmol/L, H₂O₂/Fe²⁺: 3.27 and oxidation time: 84.8 min), the maximum COD removal efficiency is determined as 91.4% by the model. The color, inert COD and UV₂₅₄ removal efficiencies are determined to be 99.9%, 97.2% and 99.5%, respectively, by the model, whereas the total COD, color, inert COD and UV₂₅₄ removal efficiencies are found respectively to be 90%, 96.5%, 95.3% and 97.2%, experimentally under the optimum operating conditions. The Fenton process improves the biodegradability of the leachate NF concentrate, increasing the BOD₅/COD ratio from the value of 0.04 to the value of 0.4. The operational cost of the process is calculated to be 0.238 €/g COD_removed. The results indicate that the Fenton oxidation process is an efficient and economical technology in improvement of the biological degradability of leachate nanofiltration concentrate and in removal of resistant organic pollutants.     

Catalytic oxidation of CO over Pt/Fe3O4 catalysts: Tuning O2 activation and CO adsorption

• Strong metal-support interaction exists on Pt/Fe₃O₄ catalysts. • Pt metal particles facilitate the formation of oxygen vacancies on Fe₃O₄. • Fe₃O₄ supports enhance the strength of CO adsorption on Pt metal particles. The self-inhibition behavior due to CO poisoning on Pt metal particles strongly impairs the performance of CO oxidation. It is an effective method to use reducible metal oxides for supporting Pt metal particles to avoid self-inhibition and to improve catalytic performance. In this work, we used in situ reductions of chloroplatinic acid on commercial Fe₃O₄ powder to prepare heterogeneous-structured Pt/Fe₃O₄ catalysts in the solution of ethylene glycol. The heterogeneous Pt/Fe₃O₄ catalysts achieved a better catalytic performance of CO oxidation compared with the Fe₃O₄ powder. The temperatures of 50% and 90% CO conversion were achieved above 260°C and 290°C at Pt/Fe₃O₄, respectively. However, they are accomplished on Fe₃O₄ at temperatures higher than 310°C. XRD, XPS, and H₂-TPR results confirmed that the metallic Pt atoms have a strong synergistic interaction with the Fe₃O₄ supports. TGA results and transient DRIFTS results proved that the Pt metal particles facilitate the release of lattice oxygen and the formation of oxygen vacancies on Fe₃O₄. The combined results of O₂-TPD and DRIFTS indicated that the activation step of oxygen molecules at surface oxygen vacancies could potentially be the rate-determining step of the catalytic CO oxidation at Pt/Fe₃O₄ catalysts. The reaction pathway involves a Pt-assisted Mars-van Krevelen (MvK) mechanism.     

A review of measurement methods for peracetic acid (PAA)

• Physical and chemical properties and application of peracetic acid solution. • Determination method of high concentration peracetic acid. • Determination method of residual peracetic acid (low concentration). Peroxyacetic acid has been widely used in food, medical, and synthetic chemical fields for the past several decades. Recently, peroxyacetic acid has gradually become an effective alternative disinfectant in wastewater disinfection and has strong redox capacity for removing micro-pollutants from drinking water. However, commercial peroxyacetic acid solutions are primarily multi-component mixtures of peroxyacetic acid, acetic acid, hydrogen peroxide, and water. During the process of water treatment, peroxyacetic acid and hydrogen peroxide (H₂O₂) often coexist, which limits further investigation on the properties of peroxyacetic acid. Therefore, analytical methods need to achieve a certain level of selectivity, particularly when peroxyacetic acid and hydrogen peroxide coexist. This review summarizes the measurement and detection methods of peroxyacetic acid, comparing the principle, adaptability, and relative merits of these methods.     

Simultaneous removal of NOx and chlorobenzene on V2O5/TiO2 granular catalyst: Kinetic study and performance prediction

• A V₂O₅/TiO₂ granular catalyst for simultaneous removal of NO and chlorobenzene. • Catalyst synthesized by vanadyl acetylacetonate showed good activity and stability. • The kinetic model was established and the synergetic activity was predicted. • Both chlorobenzene oxidation and SCR of NO follow pseudo-first-order kinetics. • The work is of much value to design of multi-pollutants emission control system. The synergetic abatement of multi-pollutants is one of the development trends of flue gas pollution control technology, which is still in the initial stage and facing many challenges. We developed a V₂O₅/TiO₂ granular catalyst and established the kinetic model for the simultaneous removal of NO and chlorobenzene (i.e., an important precursor of dioxins). The granular catalyst synthesized using vanadyl acetylacetonate precursor showed good synergistic catalytic performance and stability. Although the SCR reaction of NO and the oxidation reaction of chlorobenzene mutually inhibited, the reaction order of each reaction was not considerably affected, and the pseudo-first-order reaction kinetics was still followed. The performance prediction of this work is of much value to the understanding and reasonable design of a catalytic system for multi-pollutants (i.e., NO and dioxins) emission control.     

Evolution of humic substances in polymerization of polyphenol and amino acid based on non-destructive characterization

• Humification evolution was identified with non-destructive characterization method. • Humification process from precursors to fulvic and humic acid was confirmed. • MnO₂ alone had limited oxidation ability to form HA. • MnO₂ played a key role as a catalyst to transform FA to HA in the presence of O₂. • MnO₂ could affect the structure of the humification products. Abiotic humification is important in the formation and evolution of organic matter in soil and compost maturing processes. However, the roles of metal oxides in abiotic humification reactions under micro-aerobic remain ambiguous. The aim of this study was to use non-destructive measurement methods to investigate the role of MnO₂ in the evolution of humic substances (HSs) during oxidative polymerization of polyphenol-amino acid. Our results suggested a synergistic effect between MnO₂ and O₂ in promoting the polymerization reaction and identified that MnO₂ alone had a limited ability in accelerating the transformation of fulvic acid (FA) to humic acid (HA), whereas O₂ was the key factor in the process. Two-dimensional correlation spectroscopy (2D-COS) showed that the evolution in the UV-vis spectra followed the order of 475–525 nm>300–400 nm>240–280 nm in the humification process, indicating the formation of simple organic matter followed by FA and then HA. ¹³C nuclear magnetic resonance (¹³C NMR) analysis revealed that the products under both air and N₂ conditions in the presence of MnO₂ had greater amounts of aromatic-C than in the absence of MnO₂, demonstrating that MnO₂ affected the structure of the humification products. The results of this study provided new insights into the theory of abiotic humification.     

Assessing combined toxic effects of tetracycline and P25 titanium dioxide nanoparticles using Allium cepa bioassay

• UVA pre-irradiation to TiO₂ NPs enhanced its toxicity toward plant A. cepa. • UVA TiO₂ NPs increased intracellular ROS, resulting in more cell damage. • Cell death enhanced cell permeability and increased uptake of NPs. • Being highly toxic (EC₅₀ = 0.097 µmol/L), TC did not increase ROS generation. • Even at a low dose, TC enhanced the toxic potential of TiO₂ NPs significantly. Usage of titanium dioxide nanoparticles (TiO₂ NPs) and tetracycline (TC) has increased significantly in the present era. This leads to their release and accumulation in the environment. Both the compounds, individually, can have adverse toxic effects on the plants. Their binary mixtures can increase this degree of damage. The present study aimed to evaluate the toxicity of both the contaminants in individual and binary mixtures in Allium cepa. Further, the toxicity of TiO₂ NPs upon UVA pre-irradiation was also measured. Results showed that UVA pre-irradiated NPs (UVA-TiO₂ NPs) had a significant decrease in cell viability than their non-irradiated counterparts (NI-TiO₂), denoting an increase in photocatalytic activity upon UVA pre-irradiation. Very low concentrations of TC (EC₁₀ = 0.016 µmol/L) mixed with TiO₂ NPs significantly increased the toxicity for both UVA-TiO₂ and NI-TiO₂ NPs. Intracellular ROS generation was significantly high for UVA-TiO₂ NPs. However, TC did not have any effects on ROS production. Both the compounds exhibited genotoxic potential in A. cepa. Different chromosomal abnormalities like anaphase bridges, telophase bridges, laggard chromosomes, binucleate cells, etc. were observed. The binary mixture of UVA-TiO₂ NPs and TC showed the highest chromosomal aberrations (64.0%±1.26%) than the mixture with NI-TiO₂ or the individual contaminants. This decreased significantly after recovery (46.8%±1.92%), denoting the self-repair processes. This study proved that UVA-TiO₂ NPs were more toxic and could be enhanced further when mixed with a sub-lethal concentration of TC. This work will help to assess the risk of both compounds in the environment.     

Mechanism of dichloromethane disproportionation over mesoporous TiO2 under low temperature

• Mechanism of DCM disproportionation over mesoporous TiO₂ was studied. • DCM was completely eliminated at 350℃ under 1 vol.% humidity. • Anatase (001) was the key for disproportionation. • A competitive oxidation route co-existed with disproportionation. • Disproportionation was favored at low temperature. Mesoporous TiO₂ was synthesized via nonhydrolytic template-mediated sol-gel route. Catalytic degradation performance upon dichloromethane over as-prepared mesoporous TiO₂, pure anatase and rutile were investigated respectively. Disproportionation took place over as-made mesoporous TiO₂ and pure anatase under the presence of water. The mechanism of disproportionation was studied by in situ FTIR. The interaction between chloromethoxy species and bridge coordinated methylenes was the key step of disproportionation. Formate species and methoxy groups would be formed and further turned into carbon monoxide and methyl chloride. Anatase (001) played an important role for disproportionation in that water could be dissociated into surface hydroxyl groups on such structure. As a result, the consumed hydroxyl groups would be replenished. In addition, there was another competitive oxidation route governed by free hydroxyl radicals. In this route, chloromethoxy groups would be oxidized into formate species by hydroxyl radicals transfering from the surface of TiO₂. The latter route would be more favorable at higher temperature.     

PM-support interfacial effect and oxygen mobility in Pt,Pd or Rh-loaded (Ce,Zr,La)O2 catalysts

• Pt/CZL exhibits the optimum catalytic performance for HC and NO_x elimination. • The strong PM-Ce interaction favors the oxygen mobility and DOSC. • Pd/CZL shows higher catalytic activity for CO conversion due to more O_latt species. • Great oxygen mobility at high temperature broadens the dynamic operation window. • The relationship between DOSC and catalytic performance is revealed. The physicochemical properties of Pt-, Pd- and Rh- loaded (Ce,Zr,La)O₂ (shorted for CZL) catalysts before/after aging treatment were systematically characterized by various techniques to illustrate the relationship of the dynamic oxygen storage/release capacity and redox ability with their catalytic performances for HC, NO_x and CO conversions. Pt/CZL catalyst exhibits the optimum catalytic performance for HC and NO_x elimination, which mainly contribute to its excellent redox ability and dynamic oxygen storage/release capacity (DOSC) at lower temperature due to the stronger PM (precious metals)-support interaction. However, the worse stability of Pt-O-Ce species and volatile Pt oxides easily result in the dramatical decline in catalytic activity after aging. Pd/CZL shows higher catalytic activity for CO conversion by reason of more O_latt species as the active oxygen for CO oxidation reaction. Rh/CZL catalyst displays the widest dynamic operation window for NO_x elimination as a result of greater oxygen mobility at high temperature, and the ability to retain more Rh-O-Ce species after calcined at 1100°C effectively restrains sintering of active RhO_x species, improving the thermal stability of Rh/CZL catalyst.     

Visible-light-driven heterostructured g-C3N4/Bi-TiO2 floating photocatalyst with enhanced charge carrier separation for photocatalytic inactivation of Microcystis aeruginosa

• Bi doping in TiO₂ enhanced the separation of photo-generated electron-hole. • The performance of photocatalytic degradation of MC-LR was improved. • Coexisting substances have no influence on algal removal performance. • The key reactive oxygen species were h⁺ and ^•OH in the photocatalytic process. The increase in occurrence and severity of cyanobacteria blooms is causing increasing concern; moreover, human and animal health is affected by the toxic effects of Microcystin-LR released into the water. In this paper, a floating photocatalyst for the photocatalytic inactivation of the harmful algae Microcystis aeruginosa (M. aeruginosa) was prepared using a simple sol-gel method, i.e., coating g-C₃N₄ coupled with Bi-doped TiO₂ on Al₂O₃-modified expanded perlite (CBTA for short). The impact of different molar ratios of Bi/Ti on CBTA was considered. The results indicated that Bi doping in TiO₂ inhibited photogenerated electron-hole pair recombination. With 6 h of visible light illumination, 75.9% of M. aeruginosa (initial concentration= 2.7 × 10⁶ cells/L) and 83.7% of Microcystin-LR (initial concentration= 100 μg/L) could be removed with the addition of 2 g/L CBTA-1% (i.e., Bi/Ti molar ratio= 1%). The key reactive oxygen species (ROSs) in the photocatalytic inactivation process are h⁺ and ^•OH. The induction of the Bi⁴⁺/Bi³⁺ species by the incorporation of Bi could narrow the bandgap of TiO₂, trap electrons, and enhance the stability of CBTA-1% in the solutions with coexisting environmental substances.     

A pulsed switching peroxi-coagulation process to control hydroxyl radical production and to enhance 2,4-Dichlorophenoxyacetic acid degradation

• A new pulsed switching peroxi-coagulation (PSPC) system was developed. • The EC_T for 2,4-D removal in the PSPC was lower than that in the EF. • The iron consumption for 2,4-D removal in the PSPC was lower than that in the PC. The aim of this study was to develop a new pulsed switching peroxi-coagulation system to control hydroxyl radical (?OH) production and to enhance 2,4-Dichlorophenoxyacetic acid (2,4-D) degradation. The system was constructed with a sacrifice iron anode, a Pt anode, and a gas diffusion cathode. Production of H₂O₂ and Fe²⁺ was controlled separately by time delayers with different pulsed switching frequencies. Under current densities of 5.0 mA/cm² (H₂O₂) and 0.5 mA/cm² (Fe²⁺), the ?OH production was optimized with the pulsed switching frequency of 1.0 s (H₂O₂):0.3 s (Fe²⁺) and the ratio of H₂O₂ to Fe²⁺ molar concentrations of 6.6. Under the optimal condition, 2,4-D with an initial concentration of 500 mg/L was completely removed in the system within 240 min. The energy consumption for the 2,4-D removal in the system was much lower than that in the electro-Fenton process (68±6 vs. 136±10 kWh/kg TOC). The iron consumption in the system was ~20 times as low as that in the peroxi-coagulation process (196±20 vs. 3940±400 mg/L) within 240 min. The system should be a promising peroxi-coagulation method for organic pollutants removal in wastewater.     

Hydroxyl radical intensified Cu2O NPs/H2O2 process in ceramic membrane reactor for degradation on DMAc wastewater from polymeric membrane manufacturer

• Cu₂O NPs/H₂O₂ Fenton process was intensified by membrane dispersion. • DMAc removal was enhanced to 98% for initial DMAc of 14000 mg/L. • Analyzed time-resolved degradation pathway of DMAc under ·OH attack. High-concentration industrial wastewater containing N,N-dimethylacetamide (DMAc) from polymeric membrane manufacturer was degraded in Cu₂O NPs/H₂O₂ Fenton process. In the membrane-assisted Fenton process DMAc removal rate was up to 98% with 120 min which was increased by 23% over the batch reactor. It was found that ·OH quench time was extended by 20 min and the maximum ·OH productivity was notably 88.7% higher at 40 min. The degradation reaction rate constant was enhanced by 2.2 times with membrane dispersion (k = 0.0349 min⁻¹). DMAc initial concentration (C₀) and H₂O₂ flux (J_p) had major influence on mass transfer and kinetics, meanwhile, membrane pore size (r_p) and length (L_m) also affected the reaction rate. The intensified radical yield, fast mass transfer and nanoparticles high activity all contributed to improve pollutant degradation efficiency. Time-resolved DMAc degradation pathway was analyzed as hydroxylation, demethylation and oxidation leading to the final products of CO₂, H₂O and NO₃⁻ (rather than NH₃ from biodegradation). Continuous process was operated in the dual-membrane configuration with in situ reaction and separation. After five cycling tests, DMAc removal was all above 95% for the initial [DMAc]₀ = 14,000 mg/L in wastewater and stability of the catalyst and the membrane maintained well.     

Enhancement of the electrocatalytic oxidation of antibiotic wastewater over the conductive black carbon-PbO2 electrode prepared using novel green approach

• A novel conductive carbon black modified lead dioxide electrode is synthesized. • The modified PbO₂ electrode exhibits enhanced electrochemical performances. • BBD method could predict optimal experiment conditions accurately and reliably. • The modified electrode possesses outstanding reusability and safety. The secondary pollution caused by modification of an electrode due to doping of harmful materials has long been a big concern. In this study, an environmentally friendly material, conductive carbon black, was adopted for modification of lead dioxide electrode (PbO₂). It was observed that the as-prepared conductive carbon black modified electrode (C-PbO₂) exhibited an enhanced electrocatalytical performance and more stable structure than a pristine PbO₂ electrode, and the removal efficiency of metronidazole (MNZ) and COD by a 1.0% C-PbO₂ electrode at optimal conditions was increased by 24.66% and 7.01%, respectively. Results revealed that the electrochemical degradation of MNZ wastewater followed pseudo-first-order kinetics. This intimates that the presence of conductive carbon black could improve the current efficiency, promote the generation of hydroxyl radicals, and accelerate the removal of MNZ through oxidation. In addition, MNZ degradation pathways through a C-PbO₂ electrode were proposed based on the identified intermediates. To promote the electrode to treat antibiotic wastewater, optimal experimental conditions were predicted through the Box-Behnken design (BBD) method. The results of this study suggest that a C-PbO₂ electrode may represent a promising functional material to pretreat antibiotic wastewaters.