二氧化氯预氧化对藻类絮体形态的影响

针对高含藻高含盐杨埕水库原水藻类特征,采用聚合氯化铝(PAC)、硫酸铝(AS)、聚合硫酸铁(PFS)和氯化铁(FC)4种混凝剂进行混凝除藻试验,用图像法对藻类絮体的分形维数进行测定,分析混凝剂种类及投量、二氧化氯投加量等因素对混凝除藻效果及藻类絮体形态的影响。结果表明,杨埕水库夏季藻类种属相对较为单一,以小型色球藻、微小平裂藻、不整齐蓝纤维藻为优势藻类;4种混凝剂的除藻性能优劣依次为:AS>PAC>PFS>AC。在AS最佳投加量(以Al2SO4计)70 mg/L下,藻类的去除率为85.3%。此时,杨埕水库夏季藻类以藻类絮体分形维数值为1.54,形成的絮体密实且沉降性好。以AS为混凝剂,投加量为70 mg/L下,二氧化氯投加量为0.8 mg/L时助凝效果最好,藻类的去除率比单独投加AS时提高了6.3%,藻类絮体分形维数值为1.71,形成的藻类絮体更加密实。二氧化氯过量投加无益于藻类去除。     

利用小角度激光光散射研究阳离子有机高分子絮凝剂的絮体粒径和絮体结构

利用小角度激光光散射在线监测技术研究了不同阳离子有机高分子絮凝剂对带负电荷的高岭土颗粒体系的絮凝动力学和絮体结构.对于高电荷密度的聚二甲基二烯丙基氯化铵(PDADMAC),由于分子量低其初始絮凝反应速度较慢,最终形成的絮体也较小.絮凝过程中,其絮体结构发生重组和排列,分形维数从1.83升高到2.09,所形成的絮体密实.对于低电荷密度的2种阳离子聚丙烯酰胺(CPAM),因其分子量大投药量高,絮凝反应速度较快;但其絮体的分形维数较小且在絮凝反应中基本保持不变,形成的絮体结构开放和松散.基于有机高分子对高岭土体系浊度和zeta电位的影响,结合絮凝动力学和絮体结构分析,结果表明,PDADMAC絮凝机理是电中和作用,而随着分子量的增加和电荷密度的降低,CPAM则主要通过吸附架桥作用产生絮凝.     

絮凝条件对絮体分形结构的影响

在85kg/m³的含沙高浊水中投加阳离子高分子聚合物,借助图像分析技术与沉降技术分析探讨了不同絮凝条件下泥沙絮凝形态学参数:絮体粒径、絮体有效质量密度、絮体自由沉速、浑液面沉速与上清液余浊等的变化规律.利用表征参数“分维”定量控制不同絮凝条件(如搅拌速率、搅拌时间、高分子浓度等)对含沙高浊水絮体结构分形特性的影响.实验证明,不合适的絮凝条件将导致絮体分形构造疏松脆弱,分维值低.絮凝条件合适时(快速絮凝强度为:r₁=300r/min,t₁=10s;慢速絮凝强度:r₂=120r/min,t₂=180s;CP浓度:0.1%),絮体分形结构处于最佳状态.该状态下的絮体具有粒径较大、沉速快、有效质量密度高、粒度分布均匀,分维值最高(D₃=2.16)的特点.而且,由静沉实验测得浑液面沉速高,上清液余浊也低.泥沙絮体分形结构达最佳时的混凝性能、沉降性能与结构密实性均较理想.     

超滤的预处理工艺对比研究:化学混凝与电絮凝

对比研究了化学混凝(chemical coagulation,CC)与电絮凝(electrocoagulation,EC)作为超滤膜分离的预处理工艺,在死端过滤条件下与超滤膜的作用机制以及对膜污染的减缓效果.主要研究了Al3+投加量对膜通量、絮体性质(粒径、强度系数、恢复系数、分形维数)、以及滤饼层性质的影响.结果表明,EC作为预处理时,生成的絮体强度大且结构紧实,在膜表面堆积形成的滤饼层具有疏松多孔、亲水性强的性质;而CC作为预处理时,生成的絮体强度低且比较松散,在膜过滤过程中容易被压力压碎压实,导致滤饼层比较密实、亲水性低.因此,EC作为预处理工艺对膜污染的减缓效果好,在运行过程中可以保持较高的膜通量,膜通量较CC高约5.57%.     

加载絮体形态对短流程超滤膜污染影响效应

以聚硫酸铁（PFS）为混凝剂,微砂为载体颗粒,系统考察了采用加载絮凝-超滤联用工艺净化含高岭土、腐植酸和锑[Sb（Ⅲ）]的模拟原水过程中,不同PFS和微砂投加量条件下加载絮体形态特性以及其对超滤膜通量衰减、膜污染可逆性和宏观出水水质等的影响,并分析了膜污染机理.结果表明,PFS投加量对絮体形态及膜滤效能和膜污染影响显著,且投加量过少或过多均会产生不利影响,以30mg/L为宜;与不投加微砂的工况相比,加入微砂更易于形成大而结构较为松散的絮体,可有效削弱不可逆膜污染,并获得较为稳定的超滤出水水质;超滤末端膜比通量与絮体平均粒径呈良好的正相关性（R²=0.8774）,但因加载絮凝体系中引起分形维数变大的不同类型颗粒（包括小粒径范围絮体和未被加载絮体捕获的微砂）对超滤净水过程产生的影响各异,致使膜通量与分形维数的负相关性较差（R²=0.5760）.     

聚合硫酸铁混凝消除水中有机氯的研究

采用聚合硫酸铁(PFS)絮凝剂对水中有机氯农药(OCPs)进行强化混凝处理,并运用响应曲面法(RSM)优化分析了影响OCPs去除率的混凝条件,如pH值、原水浊度、混凝剂投加量和OCPs的初始浓度诸因素.结果表明,各影响因素交互作用显著,最佳混凝条件组合为:pH=5.0、原水浊度=150NTU、PFS投加量为12mg/L、OCPs初始浓度为200ng/L,在此条件下,PFS絮凝剂可有效去除水中OCPs,经模型验证实验得到最佳条件下去除率α-HCH为82.23%、β-HCH为71.15%、γ-HCH为77.28%、δ-HCH为86.27%、 p,p’-DDE为93.78%,与RSM预测值基本相同.结合絮体分形维数和Zeta电位对混凝效果的机理进行了探讨,表明各因素均达到了最佳水平.     

混凝-膜过滤中滤饼层对双酚A的去除强化作用研究

以聚合氯化铝(PAC)和氯化铁(FeCl3)为混凝剂,分析了双酚A(BPA)在1g/L高岭土溶液混凝过程中的特征.并借助循环错流过滤强化污染层累积的方法,评价产生滤饼层的微滤(MF)膜对BPA的截留效果.结果表明:清洁的微滤膜过滤BPA溶液在短时间内达到截留吸附饱和,之后其对BPA的吸附截留作用显著降低;混凝絮体混合液经膜过滤时产生的污染层有利于BPA的去除,且单独混凝对BPA去除率最高的混凝剂投加量下进行膜过滤时的阻力较小.PAC混凝—膜过滤后BPA去除率比单独混凝提高了34.30%;FeCl3混凝—膜过滤后BPA去除率比单独混凝提高了28.38%.初始BPA浓度对混凝-膜过滤去除率有一定影响,BPA浓度为100μg/L时,比BPA浓度为5mg/L时采用2种混凝-微滤膜过滤方式去除率均有提高.     

聚合硫酸铁(PFS)混凝腐殖酸(HA)的过程中典型操作因素的影响研究

针对聚合硫酸铁（PFS）混凝-沉淀去除腐殖酸（HA）水样的过程,通过测定典型操作因素（PFS投加量、原水pH和搅拌方式）下微絮体的zeta电位、上清液的浊度、UV254、pH值及电导率和絮体沉降体积变化,探讨了这些因素对该过程的影响.结果表明：在原水pH=6.00时,PFS混凝HA的主要机制为电中和作用,搅拌方式对PFS的最佳投加范围没有明显的影响,但单一搅拌方式下HA的去除效果更好;在原水pH=8.00时,吸附络合-卷扫絮凝成为主要的混凝机制,复合搅拌方式下PFS的最佳投加量范围大于单一搅拌方式,且前者的HA去除效果更好.整体而言,几种混凝条件下PFS最佳投药量对应的微絮体zeta电位均在-12.00mV左右;原水pH=6.00时PFS混凝-沉淀去除HA的效果比原水pH=8.00时的好,且前者形成的PFS-HA沉淀絮体体积较小,但单一搅拌方式下絮体结构的重组过程并不是影响絮体体积的主要因素.复合搅拌方式中开始阶段的高强度搅拌有助于PFS组分在HA水样中的分散而有利于其电中和作用的发挥,但对PFS的水解过程影响不大.     

Phosphorus recovery from wastewater by struvite crystallization：Property of aggregates

Struvite crystallization is a promising method to remove and recover phosphorus from wastewater to ease both the scarcity of phosphorus rock resources and water eutrophication worldwide. To date, although various kinds of reactor systems have been developed, supporting methods are required to control the struvite fines flushing out of the reactors. As an intrinsic property, aggregation is normally disregarded in the struvite crystallization process, although it is the key factor in final particle size and therefore guarantees phosphorus recovery efficiency. The present study developed a method to analyze the characteristics of struvite aggregates using fractal geometry, and the influence of operational parameters on struvite aggregation was evaluated. Due to its typical orthorhombic molecular structure, struvite particles are prone to crystallize into needle or rod shapes, and aggregate at the corners or edges of crystals. The determined fractal dimension(Dpf) of struvite aggregates was 1.52–1.31, with the corresponding range of equivalent diameter(d0.5) at 295.9–85.4 μm. Aggregates formed in relatively low phosphorus concentrations(3.0–5.0 mmol/L) and mildly alkaline conditions(pH 9.0–9.5) displayed relatively compact structures, large aggregate sizes and high aggregation strength. Increasing pH values led to continuous decrease of aggregate sizes, while the variation of Dpfwas insignificant. As to the aggregate evolution, fast growth in a short time followed by a long steady stage was observed.     

铝、铁、钛3种金属盐基混凝剂调理污泥的性能比较

以铝盐、铁盐和钛盐混凝剂为研究对象,重点比较了3种混凝剂的污泥调理性能.通过测定调理前后污泥比阻、胞外聚合物中蛋白质和多糖的含量变化,结合三维荧光光谱与分子量变化分析及调理前后污泥尺寸大小与颗粒表面形貌变化,系统比较了它们对污泥的调理性能,并揭示了调理机制.3种无机混凝剂的污泥调理能力依次为:聚合氯化铝(PAC)、钛凝胶混凝剂(TXC)、聚合硫酸铁(PFS);调理后,污泥胞外聚合物中蛋白质和多糖含量明显降低;PFS和TXC对有机物的结合能力要强于PAC,疏松结合的胞外聚合物中多糖含量是影响污泥脱水性能的关键因素;调理过程中3种混凝剂所形成污泥颗粒的大小顺序为:TXCPFSPAC,所形成污泥颗粒的大小并非影响污泥脱水性能的关键因素,无机混凝剂电中和能力和与有机物的络合能力共同影响无机混凝剂的污泥调理性能.本研究为污泥调理混凝剂的选取提供了实验和理论依据.     

引入分形维数的混凝动力学方程数值求解

运用Smoluchowskj基本原理,建立了引入絮凝体分形维数的混凝动力学模型.该模型在絮凝过程中考虑了不同时刻形成的絮凝体中引入的初始颗粒数目和空隙率,并以此来推求不同时刻形成的絮凝体所对应的分形维数.采用有限差分法对建立的混凝动力学模型进行了数值计算.结果表明,初始颗粒的结构特征和碰撞效率是影响絮凝体粒径分布的主要因素.初始颗粒的分形维数和碰撞效率越大,絮凝体粒径分布越宽泛,大尺寸的颗粒所占的份额越多.同时计算结果表明,絮凝体的分形维数有随其粒径增大而逐渐降低的趋势,其原因是絮凝体的成长粒径与絮凝体中所包含的初始颗粒增长速度不成比例.以腐殖酸为混凝对象,采用硫酸铝作为混凝剂进行混凝实验,并以其初始絮凝条件作为数值计算初始条件,研究表明数值计算分析结果和模拟结果吻合较好.     

The influence of particle size and concentration combined with pH on coagulation mechanisms

In order to evaluate the influence of particle size and particle concentration on the coagulation process, two kinds of particle suspensions, nanoparticles and microparticles,were employed to investigate the effect of particle size on coagulation mechanisms with varying coagulation parameters. Results showed that it is easier for nanoparticles to cause self-aggregation because of Brownian motion, while interception and sedimentation are the mainly physical processes affecting particle transport for microparticles, so they are more stable and disperse more easily. The particle size distribution and particle concentration had distinct influence on the coagulation mechanisms. Under neutral conditions, as the amount of coagulant increased, the coagulation mechanism for nanoparticles changed from charge neutralization to sweep flocculation and the nanoparticles became destabilized, re-stabilized and again destabilized. For microparticles, although the coagulation mechanism was the same as that of nanoparticles, the increased rate of aluminum hydroxide precipitation exceeded the adsorption of incipiently formed soluble alum species, resulting in the disappearance of the re-stabilization zone. Under acidic conditions, Brownian motion dominates for nanoparticles at low particle concentrations, while sweep flocculation is predominant at high particle concentrations. As for microparticles, charge neutralization and sweep flocculation are the mechanisms for low and high particle concentrations respectively.Under alkaline condition, although the mechanisms for both nano-and microparticles are the same, the morphology of flocs and the kinetics of floc formation are different. At low particle concentrations, nanoparticles have larger growth rate and final size of flocs, while at high particle concentrations, nanoparticles have higher fractal dimension and recovery factors.     

Coagulation behavior and floc properties of compound bioflocculant-polyaluminum chloride dual-coagulants and polymeric aluminum in low temperature surface water treatment

This study was intended to compare coagulation behavior and floc properties of two dualcoagulants polyaluminum chloride–compound bioflocculant(PAC–CBF)(PAC dose first) and compound bioflocculant–polyaluminum chloride(CBF–PAC)(CBF dose first) with those of PAC alone in low temperature drinking water treatment. Results showed that dualcoagulants could improve DOC removal efficiency from 30% up to 34%. Moreover, CBF contributed to the increase of floc size and growth rate, especially those of PAC–CBF were almost twice bigger than those of PAC. However, dual-coagulants formed looser and weaker flocs with lower breakage factors in which fractal dimension of PAC–CBF flocs was low which indicates a looser floc structure. The floc recovery ability was in the following order:PAC–CBF PAC alone CBF–PAC. The flocculation mechanism of PAC was charge neutralization and enmeshment, meanwhile the negatively charged CBF added absorption and bridging effect.     

黄土台塬土地利用方式对土壤水稳性团聚体稳定性影响

论文以黄土台塬不同土地利用方式为对象,采用几何平均直径（GMD）、平均重量直径（MWD）、分形维数（D）、破坏率（PAD）、峰凸系数（C_E）和偏倚系数（C_S）对其土壤>0.25 mm团聚体进行分析,探讨土地利用方式转变对土壤团聚体水稳性的影响及其最佳评价指标的选择。结果表明：不同利用方式土壤团聚体含量、GMD及MWD均表现为耕地<乔灌混交林地<乔木林地<天然草地<灌木林地;林和草的种植有利于促进土壤较大粒径团聚体的形成,其土壤1~5 mm粒级团聚体占>0.25 mm团聚体总量比重显著（53.90%~80.20%）,结构非均匀性明显（灌木林地和天然草地土壤尤为突出）;而耕地土壤0.25~1 mm粒级团聚体占>0.25 mm团聚体总量比重较大（约81%）,结构呈均匀性;林地和草地土壤剖面由上而下团聚体优势粒径逐渐变小,结构差异逐渐减弱,该趋势灌木林地和天然草地较为缓慢,而耕地在整个剖面上均呈优势粒径较小,结构均一;GMD和C_S可较好地衡量整个剖面土壤团聚体水稳性,而PAD可更好地描述0~20 cm深度。     

活性污泥的理化性质与絮凝调理投药量的关系

采用烧杯试验研究了活性污泥理化性质与絮凝调理投药量的关系,分析了活性污泥离心上清液黏度及其中胶体的Zeta电位和表面电荷密度、污泥絮体的粒度、分形维数和强度等理化性质指标随调理絮凝剂(CPAM,CZ-8698)投药量的变化规律,探讨了这些指标在确定絮凝调理最佳投药量方面的差异.结果表明,CZ-8698的投药量对污泥的脱水性能和理化性质均可产生明显的影响,基于毛细吸水时间(CST)、污泥比阻(SRF)确定的活性污泥絮凝调理的最佳投药量范围为4.28～7.13g.kg-1,对应的CST与SRF值分别为(12.62±1.39)s、0.56×1012m.kg-1.在此最佳投药量区间,污泥离心上清液中胶体的Zeta电位与表面电荷密度均由负值变为正值,污泥絮体的分形维数分别为1.09(一维)和1.51(二维),其表面不规则程度最低、结构较为密实;污泥絮体的粒径随着絮凝剂投药量的增加持续增大到mm尺度,但其强度在投药量高于4.60 g.kg-1以后逐渐趋于稳定.此外,当絮凝剂投药量低于上述最佳范围时,污泥离心上清液的黏度已经达到了最小值(1.24±0.04)mPa.s.     

混凝-接触氧化处理印染废水的试验研究

对混凝-生物接触氧化法处理印染废水进行研究。混凝部分试验研究了聚合氯化铝(PAC)、聚合硫酸铁(PFS)、氯化铁(FC)3种混凝剂对印染废水的处理效果。结果表明:PAC的处理效果最好,并确定了混凝的最佳pH值和投加量。在生物接触氧化试验部分,主要考察了水力停留时间和曝气量对COD去除率的影响,确定了最佳工艺参数。经试验,脱色率和COD去除率分别达95.68%和95.23%。     

高浓度悬浊液絮体分形结构的发展变化研究

以黄河泥沙为代表的高浓度悬浊液架桥絮凝实验研究表明,絮体结构具有分形特性.絮体的分形构造在从疏松多孔、开放的分枝状DLCA构造逐步演变到密实的最佳RLCA构造后,又开始呈现疏松脆弱结构的特征.絮体的最佳分形结构只能保持一段时间.絮体分形结构的发展变化规律可用参数"分维"来表征.利用"分维"作为定量控制工具以获取沉降性能与脱水性能良好的理想絮体构造.絮体分形结构还受含沙量、搅拌强度、搅拌时间等因素的影响.      

三种常见混凝机理为主导条件下絮体特性研究

以模拟低浊微污染水为原水,硫酸铝[Al2 (SO4)3]为混凝剂,考察了3种常见混凝机理(电性中和、吸附架桥和网捕卷扫)为主导条件下絮体的成长过程、二维边界分形维数(Dpf)和比表面积及其与混凝效果的相关性.结果表明:吸附架桥为主导机理下絮体最大增长速率S (0.951)最快,达到稳定后絮凝指数FI最大(3.7%),二维边界分形维数Dpf最大(1.587),絮体呈块状且絮体间出现孔状间隙,比表面积介于网捕卷扫和电性中和之间[网捕卷扫(83.646m2/g)>吸附架桥(98.808m2/g)>电性中和(116.046m2/g)];FI值、S及Dpf变化与浊度去除率相关性较好,其相关系数分别达0.979、0.982和0.963,同时比表面积大的絮体吸附容量大,有机物的去除率高.     

混凝絮凝体的分形与沉降特性实验研究

在混凝絮凝体的分形与沉降特性实验研究中,通过自行设计的絮凝体混凝、沉降、观测功能的一体装置,求出了在不同混凝工况下所形成混凝絮凝体的分形维数和沉降速度,并分析了相应的变化趋势和原因。     

Mechanism of calcium mitigating membrane fouling in submerged membrane bioreactors

Two parallel membrane bioreactors (MBRs) were operated under different calcium dosages (168.5, 27 mg/L) to gain a better understanding of the mechanism of retarding membrane fouling by adding calcium. The results showed that the particle size of sludge flocs increased and the particle size distribution tended to be narrow at the optimum dosage (168.5 mg/L). Calcium was effective in decreasing loosely bound extracellular polymeric substances (LB-EPS) in microbial flocs and soluble microbial products (SMP) in the supernatant at the dosage of 168.5 mg/L by strengthening the neutralization and bridging of EPS with flocs. Furthermore, the amount of COD_S and COD_C decreased in both the mixed liquor and the fouling cake layer on the membrane surface. In order to compare the filtration characteristics of cake layers from the MBRs with the two calcium dosages, the specific cake resistance and the compressibility coefficient were measured. The specific cake resistance from the MBR with optimum dosage (168.5 mg/L) was distinctly lower than that with low dosage (27 mg/L). The compressibility coefficient of the cake layers under two dosages were respectively attained as 0.65, 0.91. Scanning electron microscopy (SEM) and three-dimensional confocal scanning laser microscope analysis (CLSM) images were utilized to observe the gel layer directly.