Traffic generated non-exhaust particulate emissions from concrete pavement: A mass and particle size study for two-wheelers and small cars

This study aimed to understand the non-exhaust (NE) emission of particles from wear of summer tire and concrete pavement, especially for two wheelers and small cars. A fully enclosed laboratory-scale model was fabricated to simulate road tire interaction with a facility to collect particles in different sizes. A road was cast using the M-45 concrete mixture and the centrifugal casting method. It was observed that emission of large particle non exhaust emission (LPNE) as well as PM₁₀ and PM_2.5 increased with increasing load. The LPNE was 3.5 mg tire⁻¹ km⁻¹ for a two wheeler and 6.4 mg tire⁻¹ km⁻¹ for a small car. The LPNE can lead to water pollution through water run-off from the roads. The contribution of the PM₁₀ and PM_2.5 was smaller compared to the LPNE particles (less than 0.1%). About 32 percent of particle mass of PM₁₀ was present below 1 μm. The number as well as mass size distribution for PM₁₀ was observed to be bi-modal with peaks at 0.3 μm and 4–5 μm. The NE emissions did not show any significant trend with change in tire pressure.     

Products and stability of phosphate reactions with lead under freeze-thaw cycling in simple systems

Orthophosphate fixation of metal contaminated soils in environments that undergo freeze-thaw cycles is understudied. Freeze-thaw cycling potentially influences the reaction rate, mineral chemical stability and physical breakdown of particles during fixation. This study determines what products form when phosphate (triple superphosphate [Ca(H₂PO₄)₂] or sodium phosphate [Na₃PO₄]) reacts with lead (PbSO₄ or PbCl₂) in simple chemical systems in vitro, and assesses potential changes in formation during freeze-thaw cycles. Systems were subjected to multiple freeze-thaw cycles from +10 °C to −20 °C and then analysed by X-ray diffractometry. Pyromorphite formed in all systems and was stable over multiple freeze-thaw cycles. Low temperature lead orthophosphate reaction efficiency varied according to both phosphate and lead source; the most time-efficient pyromorphite formation was observed when PbSO₄ and Na₃PO₄ were present together. These findings have implications for the manner in which metal contaminated materials in freezing ground can be treated with phosphate.     

N2O emissions from municipal solid waste landfills with selected infertile cover soils and leachate subsurface irrigation

This study presents the field investigations into the effects of cover soils and leachate subsurface irrigation on N₂O emissions from municipal solid waste landfills. Landfill Site A and Site B, covered with carefully chosen infertile soils, were selected to monitor their diurnal and seasonal variations of N₂O emissions. The annual average N₂O flux was 469 ± 796 μg N₂O-N m⁻² h⁻¹ in Site B with leachate subsurface irrigation, three times that of Site A without leachate irrigation. When an additional soil containing lower contents of carbon and nitrogen was introduced to cover part of Site B, its N₂O fluxes decreased by 1-2 orders of magnitude compared with the left area of Site B. This suggested that carefully selected cover soils could substantially reduce N₂O emissions even under leachate subsurface irrigation. Statistical analysis proved that the availabilities of soil moisture and mineralized nitrogen were the key parameters controlling landfill N₂O emissions.     

Nitrous oxide and methane emission from a flooded rice field as influenced by separate and combined application of herbicides bensulfuron methyl and pretilachlor

Combination of divergent active principles to achieve broad-spectrum control is gaining popularity to manage the weed menace in intensive agriculture. However, such application could have non-target impacts on the soil processes affecting soil ecology and environmental interactions. A field experiment was conducted to investigate the impact of separate and combined applications of herbicides bensulfuron methyl and pretilachlor on the emission of N₂O and CH₄, and related soil and microbial parameters in a flooded alluvial field planted to rice cv Lalat. Single application of the herbicide bensulfuron methyl or pretilachlor resulted in a significant reduction of N₂O and CH₄ emissions while the combination of these two herbicides distinctly increased N₂O and CH₄ emissions. Cumulative N₂O emissions (kg N₂O-N) followed the order of bensulfuron methyl (0.35 kg ha⁻¹) < pretilachlor (0.36 kg ha⁻¹) < control (0.45 kg ha⁻¹) < bensulfuron methyl 0.6% + pretilachlor 6.0% single dose (0.49 kg ha⁻¹) < bensulfuron methyl 0.6% + pretilachlor 6.0% double dose (0.54 kg ha⁻¹). Cumulative CH₄ emissions (kg CH₄), on the other hand, followed the order of bensulfuron methyl (47.89 kg ha⁻¹) < pretilachlor (73.17 kg ha⁻¹) < bensulfuron methyl 0.6% + pretilachlor 6.0% single dose (93.50 kg ha⁻¹) < control (106.54 kg ha⁻¹) < bensulfuron methyl 0.6% + pretilachlor 6.0% double dose (124.67 kg ha⁻¹). The inhibitory effect of separate application of herbicides bensulfuron methyl 0.6% and pretilachlor 6.0% on N₂O emission was linked to lower mineral N, lower denitrifying and nitrifying activity and low denitrifier and nitrifier populations. Inhibitory effect on CH₄ emission, on the contrary, was linked to prevention in the drop of redox potential, lower readily mineralizable carbon (RMC) and microbial biomass carbon (MBC) contents as well as lower methanogenic and higher methanotrophic bacterial population. Admittedly, stimulatory effect of combined application of herbicides bensulfuron methyl 0.6% and pretilachlor 6.0% at double dose on N₂O and CH₄ emission was related to reversal of the identified indicators of inhibition. Results indicate that while individual application of herbicides bensulfuron methyl 0.6% or pretilachlor 6.0% can reduce N₂O and CH₄ emission from flooded soil planted to rice, their combined application at normal dose can keep the emission at a comparatively lower level with significantly higher grain yield as compared to the herbicides applied alone.     

Long-term variation of PM2.5 levels and composition at rural, urban, and roadside sites in Hong Kong: Increasing impact of regional air pollution

Long-term study of air pollution plays a decisive role in formulating and refining pollution control strategies. In this study, two 12-month measurements of PM_2.5 mass and speciation were conducted in 00/01 and 04/05 to determine long-term trend and spatial variations of PM_2.5 mass and chemical composition in Hong Kong. This study covered three sites with different land-use characteristics, namely roadside, urban, and rural environments. The highest annual average PM_2.5 concentration was observed at the roadside site (58.0±2.0 μg m⁻³ (average±2σ) in 00/01 and 53.0±2.7 μg m⁻³ in 04/05), followed by the urban site (33.9±2.5 μg m⁻³ in 00/01 and 39.0±2.0 μg m⁻³ in 04/05), and the rural site (23.7±1.9 μg m⁻³ in 00/01 and 28.4±2.4 μg m⁻³ in 04/05). The lowest PM_2.5 level measured at the rural site was still higher than the United States’ annual average National Ambient Air Quality Standard of 15 μg m⁻³. As expected, seasonal variations of PM_2.5 mass concentration at the three sites were similar: higher in autumn/winter and lower in summer. Comparing PM_2.5 data in 04/05 with those collected in 00/01, a reduction in PM_2.5 mass concentration at the roadside (8.7%) but an increase at the urban (15%) and rural (20%) sites were observed. The reduction of PM_2.5 at the roadside was attributed to the decrease of carbonaceous aerosols (organic carbon and elemental carbon) (>30%), indicating the effective control of motor vehicle emissions over the period. On the other hand, the sulfate concentration at the three sites was consistent regardless of different land-use characteristics in both studies. The lack of spatial variation of sulfate concentrations in PM_2.5 implied its origin of regional contribution. Moreover, over 36% growth in sulfate concentration was found from 00/01 to 04/05, suggesting a significant increase in regional sulfate pollution over the years. More quantitative techniques such as receptor models and chemical transport models are required to assess the temporal variations of source contributions to ambient PM_2.5 mass and chemical speciation in Hong Kong.     

Polychlorinated dibenzo-p-dioxin and dibenzofuran in urban air of an Andean city

Particle-bound polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/Fs) in ambient air were monitored together with particulate matter less than 10 μm (PM₁₀) at three sampling sites of the Andean city of Manizales, Colombia; during September 2009 and July 2010. PCDD/Fs ambient air emissions ranged from 1 fg WHO-TEQ m⁻³ to 52 fg WHO-TEQ m⁻³ in particulate fraction. The PM₁₀ concentrations ranged from 23 μg m⁻³ to 54 μg m⁻³. Concentrations of PM₁₀ and PCDD/Fs in ambient air observed for Manizales - a medium sized city with a population of 380 000 - were comparable to concentrations in larger cities. The highest concentrations of PCDD/Fs and PM₁₀ found in this study were determined at the central zone of the city, characterized by public transportation density, where diesel as principal fuel is used. In addition, hypothetical gas fractions of PCDD/Fs were calculated from theoretical K_p data. Congener profiles of PCDD/Fs exhibited ratios associated with different combustion sources at the different sampling locations, ranging from steel recycling to gasoline and diesel engines. Taking into account particle and gas hypothetical fraction of PCDD/Fs, Manizales exhibited values of PCDD/Fs equivalent to rural and urban-industrial sites in the southeast and center of the city respectively. Poor correlation of PCDDs with PM₁₀ (r = −0.55 and r = 0.52) suggests ambient air PCDDs were derived from various combustion sources. Stronger correlation was observed of PCDFs with PM₁₀. Poor correlation between precipitation and reduced PM₁₀ concentration in ambient air (r = −0.45) suggested low PM₁₀ removal by rainfall.     

Sources and processes affecting concentrations of PM10 and PM2.5 particulate matter in Birmingham (U.K.)

Hourly average concentrations of PM₁₀ and PM_2.5 have been measured simultaneously at a site within Birmingham U.K. between October 1994 and October 1995. Comparison of PM₁₀ and NO_x data with two other sites in the same city shows comparable summer and winter mean concentrations and highly significant inter-site correlations for both hourly and daily mean data. Over a four-month period samples were also collected for chemical analysis of sulphate, nitrate, chloride, ammonium and elemental and organic carbon. Analysis of the data indicates a marked difference between summer and winter periods. In the winter months PM_2.5 comprises about 80% of PM₁₀ and is strongly correlated with NO_x indicating the importance of road traffic as a source. In the summer months, coarse particles (PM₁₀−PM_2.5) account for almost 50% of PM₁₀ and the influence of resuspended surface dusts and soils and of secondary particulate matter is evident. The chemical analysis data are also consistent with three sources dominating the PM₁₀ composition: vehicle exhaust emissions, secondary ammonium salts and resuspended surface dusts. Coarse particles from resuspension showed a positive dependence on windspeed, whilst elemental carbon derived from road traffic exhibited a negative dependence.     

Influence of soil ageing on bioavailability and ecotoxicity of lead carried by process waste metallic ultrafine particles

Ultrafine particulate matters enriched with metals are emitted into the atmosphere by industrial activities and can impact terrestrial and aquatic ecosystems. Thus, this study investigated the environmental effects of process particles from a lead-recycling facility after atmospheric deposition on soils and potential run-off to surface waters. The toxicity of lead-enriched PM for ecosystems was investigated on lettuce and bacteria by (i) germination tests, growth assays, lead transfer to plant tissues determination and (ii) Microtox analysis.The influence of ageing and soil properties on metal transfer and ecotoxicity was studied using three different soils and comparing various aged, spiked or historically long-term polluted soils. Finally, lead availability was assessed by 0.01 M CaCl₂ soil extraction.The results showed that process PM have a toxic effect on lettuce seedling growth and on Vibrio fischeri metabolism. Soil-PM interactions significantly influence PM ecotoxicity and bioavailability; the effect is complex and depends on the duration of ageing. Solubilisation or stabilisation processes with metal speciation changes could be involved. Finally, Microtox and phytotoxicity tests are sensitive and complementary tools for studying process PM ecotoxicity.     

An assessment of indoor air quality in recent Mexican immigrant housing in Commerce City, Colorado

An indoor air quality assessment was conducted on 100 homes of recent Mexican immigrants in Commerce City, Colorado, an urban industrial community north of Denver. Head of households were administered a family health survey, filled out an activity diary, and participated in a home inspection. Carbon monoxide (CO) and carbon dioxide (CO₂) were measured for 24 h inside the main living area and outside of the homes. Harvard Impactors were used to collect 24-h samples of PM_2.5 at the same locations for gravimetric analysis. Dust samples were collected by vacuuming carpeting and flooring at four locations within the home and analyzed by ELISA for seven allergens. Mean indoor and outdoor PM_2.5 levels were 27.2 and 8.5 μg m⁻³, respectively. Indoor PM_2.5 and CO₂ were elevated in homes for which the number of hours with door/window open was zero compared to homes in which the number of hours was high (>15 h). Indoor PM_2.5 levels did not correlate with outdoor levels and tended to increase with number of inhabitants, and results indicate that the source of indoor particles were occupants and their activities, excluding smoking and cooking. Mean indoor CO₂ and CO levels were 1170 and 2.4 ppm, respectively. Carbon monoxide was higher than the 24-h National Ambient Air Quality Standard in 3 of the homes. The predominant allergens were cat (Fel d 1) and mouse (Mus m 1) allergens, found in 20 and 34 homes, respectively.     

Source characterization of ambient fine particles at multiple sites in the Seattle area

To identify major PM_2.5 (particulate matter ≤2.5 μm in aerodynamic diameter) sources with a particular emphasis on the ship engine emissions from a major port, integrated 24 h PM_2.5 speciation data collected between 2000 and 2005 at five United State Environmental Protection Agency's Speciation Trends Network monitoring sites in Seattle, WA were analyzed. Seven to ten PM_2.5 sources were identified through the application of positive matrix factorization (PMF). Secondary particles (12–26% for secondary nitrate; 17–20% for secondary sulfate) and gasoline vehicle emissions (13–31%) made the largest contributions to the PM_2.5 mass concentrations at all of the monitoring sites except for the residential Lake Forest site, where wood smoke contributed the most PM_2.5 mass (31%). Other identified sources include diesel vehicle emissions, airborne soil, residual oil combustion, sea salt, aged sea salt, metal processing, and cement kiln. Residual oil combustion sources identified at multiple monitoring sites point clearly to the Port of Seattle suggesting ship emissions as the source of oil combustion particles. In addition, the relationship between sulfate concentrations and the oil combustion emissions indicated contributions of ship emissions to the local sulfate concentrations. The analysis of spatial variability of PM_2.5 sources shows that the spatial distributions of several PM_2.5 sources were heterogeneous within a given air shed.     

Susceptibility of epigeic earthworm Eisenia fetida to agricultural application of six insecticides

Ecotoxicological risks of agricultural application of six insecticides to soil organisms were evaluated by acute toxicity tests under laboratory condition following OECD guidelines using the epigeic earthworm Eisenia fetida as the test organism. The organochlorine insecticide endosulfan (LC₅₀ - 0.002 mg kg⁻¹) and the carbamate insecticides aldicarb (LC₅₀ - 9.42 mg kg⁻¹) and carbaryl (LC₅₀ - 14.81 mg kg⁻¹) were found ecologically most dangerous because LC₅₀ values of these insecticides were lower than the respective recommended agricultural dose (RAD). Although E. fetida was found highly susceptible to the pyrethroid insecticide cypermethrin (LC₅₀ - 0.054 mg kg⁻¹), the value was higher than its RAD. The organophosphate insecticides chlorpyrifos (LC₅₀ - 28.58 mg kg⁻¹), and monocrotophos (LC₅₀ - 39.75 mg kg⁻¹) were found less toxic and ecologically safe because the LC₅₀ values were much higher than their respective RAD.     

Removal of Rhodamine B under visible irradiation in the presence of Fe⁰, H₂O₂, citrate and aeration at circumneutral pH

A new Vis-Fe⁰-H₂O₂-citrate-O₂ system comprising zero-valent iron, hydrogen peroxide, citrate anion and aeration at circumneutral pH under visible irradiation was studied. 21 μmol L⁻¹ of Rhodamine B (RhB) was chosen as the substrate to be tested. Experiments were conducted under conditions of 2.9 mmol L⁻¹ of H₂O₂, 12.6 g of Fe⁰ and 1.0 mmol L⁻¹ of citrate at pH 7.5. Results showed that, in 1 h reaction, 54% of RhB was removed with corresponding 26% of COD reduced. Meanwhile, the amount of released dissolved irons from Fe⁰ surface was found to be at a very low level as <5.4 μmol L⁻¹. Extinguishing tests with isopropanol suggested that RhB oxidation by hydroxyl radicals was the main process taken place in Vis-Fe⁰-H₂O₂-citrate-O₂ system, which accounted for 75% of substrate removal in 3 h reaction. Control and factor influencing experiments showed that the prohibitive extents of individual factor importance on RhB removal followed a decreasing order of Fe⁰ > H₂O₂ > citrate > Vis > O₂. This study showed an excellent system that could remove refractory organic compounds from water in laboratory researches, and also provided a good idea to reduce secondary contamination by dissolved irons in future investigations.     

Vapor-phase concentrations of PAHs and their derivatives determined in a large city: Correlations with their atmospheric aerosol concentrations

Thirteen PAHs, five nitro-PAHs and two hydroxy-PAHs were determined in 55 vapor-phase samples collected in a suburban area of a large city (Madrid, Spain), from January 2008 to February 2009. The data obtained revealed correlations between the concentrations of these compounds and a series of meteorological factors (e.g., temperature, atmospheric pressure) and physical–chemical factors (e.g., nitrogen and sulfur oxides). As a consequence, seasonal trends were observed in the atmospheric pollutants. A “mean sample” for the 14-month period would contain a total PAH concentration of 13 835 ± 1625 pg m⁻³ and 122 ± 17 pg m⁻³ of nitro-PAHs. When the data were stratified by season, it emerged that a representative sample of the coldest months would contain 18 900 ± 2140 pg m⁻³ of PAHs and 150 ± 97 pg m⁻³ of nitro-PAHs, while in an average sample collected in the warmest months, these values drop to 9293 ± 1178 pg m⁻³ for the PAHs and to 97 ± 13 pg m⁻³ for the nitro-PAHs. Total vapor phase concentrations of PAHs were one order of magnitude higher than concentrations detected in atmospheric aerosol samples collected on the same dates. Total nitro-PAH concentrations were comparable to their aerosol concentrations whereas vapor phase OH-PAHs were below their limits of the detection, indicating these were trapped in airborne particles.     

Photocatalytic removal of organic pollutants in aqueous solution by Bi(4)Nb(x)Ta((1-x))O(8)I

In this work, Bi₄Nb_xTa_(1−x)O₈I photocatalysts have been synthesized by solid state reaction method and characterized by powder X-ray diffraction, scanning electron microscope and UV-Vis near infrared diffuse reflectance spectroscopy. The photocatalytic activity of these photocatalysts was evaluated by the degradation of methyl orange (MO) in aqueous solutions under visible light, UV light and solar irradiation. The effects of catalyst dosage, initial pH and MO concentration on the removal efficiency were studied, and the photocatalytic reaction kinetics of MO degradation as well. The results indicated that Bi₄Nb_xTa_(1−x)O₈I exhibited high photocatalytic activity for the removal of MO in aqueous solutions. For example, the removal efficiency of MO by Bi₄Nb_0.1Ta_0.9O₈I was as high as 92% within 12 h visible light irradiation under the optimal conditions: initial MO concentration of 5-10 mg L⁻¹, catalyst dosage of 6 g L⁻¹ and natural pH (6-8), the MO molecules could be completely degradated by Bi₄Nb_0.1Ta_0.9O₈I within 40 min under UV light irradiation, and the photodegradation efficiency reaches to 60% after 7 h solar irradiation. Furthermore, the photocatalytic degradation of Bisphenol A (BPA) was also investigated under visible light irradiation. It is found that 99% BPA could be mineralized by Bi₄Nb_0.1Ta_0.9O₈I after 16 h visible light irradiation. Through HPLC/MS, BOD, TOC, UV-Vis measurements, we determined possible degradation products of MO and BPA. The results indicated that MO was degradated into products which are easier to be biodegradable and innocuous treated, and BPA could be mineralized completely. Furthermore, the possibility for the photosensitization effect in the degradation process of MO under visible light irradiation has been excluded.     

Particulates and Metallic Elements Monitoring at Two Sampling Sites (Harbor,Airport) in Taiwan

This study characterized the dry deposition flux and dry deposition velocity (Vd) of metallic elements attached on particulate matter. Specifically, large particles (>10 μm), coarse particles (10 μm～2.5 μm), and fine particles (<2.5 μm) were studied at the Gong Ming Junior High School (Taichung Airport) and Taichung Harbor sampling sites in central Taiwan. Ambient air samples were collected to determine total suspended particulate matter (TSP), dry deposition plate (DDP), Vd, coarse particulate matter (PM_2.5–10) and fine particulate matter (PM_2.5), and metallic elements concentrations at the Airport and Taichung Harbor sites between June 17, 2013, and November 14, 2013. The results revealed that the average TSP, DDP, Vd, PM_2.5–10, and PM_2.5 particulate at the Airport were 54.55 (μg/m³), 902.25 (μg/m²-min), 17.11 (m/sec), 0.003 (μg/m³), and 0.010 (μg/m³), respectively; while these values at Taichung Harbor were 63.66 (μg/m³), 539.69 (μg/m²-min), 9.94 (m/sec), 0.003 (μg/m³), and 0.014 (μg/m³), respectively. In addition, the results showed that the average Cu and Pb concentrations were higher than Cr, Ni, and Cd for both the airport and harbor sampling sites. Furthermore, Cr, N, Cu, Cd, and Pb had the highest average concentrations versus those reported for other study areas, with one exception: The results obtained in Kacanik, Kosovo, during 2005. The average metallic elements concentrations order was Cu > Pb > Cr > Ni > Cd.     

Atmospheric transport of urban-derived NH(x): Evidence from nitrogen concentration and delta(15)N in epilithic mosses at Guiyang, SW China

Nitrogen concentration and δ¹⁵N in 175 epilithic moss samples were investigated along four directions from urban to rural sites in Guiyang, SW China. The spatial variations of moss N concentration and δ¹⁵N revealed that atmospheric N deposition is dominated by NH_x-N from two major sources (urban sewage NH₃ and agricultural NH₃), the deposition of urban-derived NH_x followed a point source pattern characterized by an exponential decline with distance from the urban center, while the agricultural-derived NH_x was shown to be a non-point source. The relationship between moss N concentration and distance (y = 1.5e^−0.13x + 1.26) indicated that the maximum transporting distance of urban-derived NH_x averaged 41 km from the urban center, and it could be determined from the relationship between moss δ¹⁵N and distance [y = 2.54 ln(x) − 12.227] that urban-derived NH_x was proportionally lower than agricultural-derived NH_x in N deposition at sites beyond 17.2 km from the urban center. Consequently, the variation of urban-derived NH_x with distance from the urban center could be modeled as y = 56.272e^−0.116x − 0.481 in the Guiyang area.     

Impact of biochar application to a Mediterranean wheat crop on soil microbial activity and greenhouse gas fluxes

Biochar has been recently proposed as a management strategy to improve crop productivity and global warming mitigation. However, the effect of such approach on soil greenhouse gas fluxes is highly uncertain and few data from field experiments are available. In a field trial, cultivated with wheat, biochar was added to the soil (3 or 6 kg m⁻²) in two growing seasons (2008/2009 and 2009/2010) so to monitor the effect of treatments on microbial parameters 3 months and 14 months after char addition. N₂O, CH₄ and CO₂ fluxes were measured in the field during the first year after char addition. Biochar incorporation into the soil increased soil pH (from 5.2 to 6.7) and the rates of net N mineralization, soil microbial respiration and denitrification activity in the first 3 months, but after 14 months treated and control plots did not differ significantly. No changes in total microbial biomass and net nitrification rate were observed. In char treated plots, soil N₂O fluxes were from 26% to 79% lower than N₂O fluxes in control plots, excluding four sampling dates after the last fertilization with urea, when N₂O emissions were higher in char treated plots. However, due to the high spatial variability, the observed differences were rarely significant. No significant differences of CH₄ fluxes and field soil respiration were observed among different treatments, with just few exceptions. Overall the char treatments showed a minimal impact on microbial parameters and GHG fluxes over the first 14 months after biochar incorporation.     

Nano-TiO2 enhances the toxicity of copper in natural water to Daphnia magna

The acute toxicity of engineered nanoparticles (NPs) in aquatic environments at high concentrations has been well-established. This study demonstrates that, at a concentration generally considered to be safe in the environment, nano-TiO₂ remarkably enhanced the toxicity of copper to Daphnia magna by increasing the copper bioaccumulation. Specifically, at 2 mg L⁻¹ nano-TiO₂, the (LC₅₀) of Cu²⁺ concentration observed to kill half the population, decreased from 111 μg L⁻¹ to 42 μg L⁻¹. Correspondingly, the level of metallothionein decreased from 135 μg g⁻¹ wet weight to 99 μg g⁻¹ wet weight at a Cu²⁺ level of 100 μg L⁻¹. The copper was found to be adsorbed onto the nano-TiO₂, and ingested and accumulated in the animals, thereby causing toxic injury. The nano-TiO₂ may compete for free copper ions with sulfhydryl groups, causing the inhibition of the detoxification by metallothioneins.     

Chemical composition of fine particles from incense burning in a large environmental chamber

 This study is aimed to characterize the major chemical compositions of PM_2.5 from incense burning in a large environmental chamber. Chemical analyses, including X-ray fluorescence for elemental species, ion chromatography for water soluble inorganic species (chloride, nitrate, sulfate, sodium, potassium, ammonium) and thermal/optical reflectance analysis for carbon species were carried out for combustion of three incense categories (traditional, aromatic and church incense). The average concentrations from incense burning ranged from 139.8 to 4414.7 μg m⁻³ for organic carbon (OC), and from 22.8 to 74.0 μg m⁻³ for elemental carbon (EC), respectively. The average OC and EC concentrations in PM_2.5 of three incense categories were in the order of church incense>traditional incense>aromatic incense. OC/EC ratios ranged from 7.0 to 39.1 for the traditional incense, with an average of 21.7; from 3.2 to 11.9 for the aromatic incense, with an average of 7.7. The concentrations of Cl⁻, SO₄²⁻, Na⁺ and K⁺ were highly variable. On average, the inorganic ion concentration sequence was traditional incense>church incense>aromatic incense. The profiles for elements were dominated by Na, Cl and K. In general, the major components in PM_2.5 fraction from incense burning are OC (especially OC2, OC3 and OC4), EC and K.