A Modified Power Law Representation of the Pasquill-Gifford Dispersion Coefficients

Abstract

To broaden the beneficial reuse of sewage sludge, small amounts of nanomaterial were considered as additives to evaluate influences of nanomaterials on microstructures of sludge cement paste. Paste specimens were manufactured using different mix designs and cured for various ages. Tests such as scanning electron microscope, X-ray diffraction, transmission electron microscope, and mercury intrusion porosimetry were then performed. Results obtained indicated that the quantities of crystallization in hydrates rose with the increased amounts of nanomaterial added. Moreover, nanomaterial additives could make crystallizations denser, pore sizes smaller, and the number of pores decreased. Consequently, the strength of sludge cement paste became better as more amounts of nanomaterial were added.     

Hydration properties of eco-cement pastes from waste sludge ash clinkers

Three types of hydraulic cements have been developed by incorporating sludge ash from a primary sewage treatment plant and a water purification plant, as well as slag from steelworks (ferrate), as a partial replacement for clay, silica, alumina, and iron oxide in raw cement meal. The raw meal for the pre-determined recipes was prepared by heating it to 1400 degrees C for 6 hr in a clinkerization process, using a simulated incinerator and smelter. The major components of ordinary Portland cement, C3S, C2S, C3A, and C4AF, were all found in the clinkers. Of the three types of eco-cements, the eco-cement A paste was most similar to ordinary Portland cement in terms of composition and compressive strength development, while the eco-cement B paste showed early strength development. The differential thermal analysis species analyses indicated that the hydrates in the eco-cement pastes were mainly calcium hydroxide and CSH gels, like those found in ordinary Portland cement paste. Moreover, the degree of hydration, as determined by nuclear magnetic resonance, increased in all eco-cement pastes with an increasing curing age. The results indicate that it indeed is feasible to use sludge ash and ferrate to replace up to 20% of the mineral components of raw materials for cement.     

Hydration Properties of Eco-Cement Pastes from Waste Sludge Ash Clinkers

Abstract

Three types of hydraulic cements have been developed by incorporating sludge ash from a primary sewage treatment plant and a water purification plant, as well as slag from steelworks (ferrate), as a partial replacement for clay, silica, alumina, and iron oxide in raw cement meal. The raw meal for the pre-determined recipes was prepared by heating it to 1400 °C for 6 hr in a clinkerization process, using a simulated incinerator and smelter. The major components of ordinary Portland cement, C₃S, C₂S, C₃A, and C₄AF, were all found in the clinkers. Of the three types of eco-cements, the eco-cement A paste was most similar to ordinary Portland cement in terms of composition and compressive strength development, while the eco-cement B paste showed early strength development. The differential thermal analysis species analyses indicated that the hydrates in the eco-cement pastes were mainly calcium hydroxide and CSH gels, like those found in ordinary Portland cement paste. Moreover, the degree of hydration, as determined by nuclear magnetic resonance, increased in all eco-cement pastes with an increasing curing age. The results indicate that it indeed is feasible to use sludge ash and ferrate to replace up to 20% of the mineral components of raw materials for cement.     

纳米材料对膜生物反应器影响的试验研究

通过向一体式膜生物反应器中投加纳米材料来改变料液性质,预防膜污染和提高膜生物反应器对污染物的去除效率,并利用扫描电镜分析中空纤维膜的表观结构的变化情况,通过红外光谱分析活性污泥性质的变化,以探讨防治膜污染的机理。试验结果表明,纳米材料的投加对COD和NH₃-N的去除无明显影响,提高了TP的去除率,TP去除率达70%。而且投加纳米材料可改变活性污泥的性质和生物膜的表观结构,减缓膜污染。     

基于响应面法的污泥快速固化效能综合影响

针对现有污泥固化技术存在的固化养护时间长、低温条件下固化效能低等问题。研究提出污泥快速（3d）固化技术,采用响应曲面分析方法,重点考察了石灰、组分A、硅酸盐水泥、粉煤灰和温度等5因素对固化效能的综合影响,研究结果表明,石灰、组分A、硅酸盐水泥、粉煤灰和养护温度等因素对3d固化体的无侧限抗压强度和含水率的线性效应显著,石灰和组分A、石灰和养护温度对无侧限抗压强度的交互影响显著,石灰和粉煤灰、组分A和养护温度、硅酸盐水泥和粉煤灰对含水率的交互影响显著;得出了5因素对固化体3d无侧限抗压强度和含水率影响的定量模型,可对污泥快速固化进行优化和预测;并利用XRD和SED对污泥固化块的化学成分和微观结构进行了分析。     

基于响应面法的污泥快速固化效能综合影响简

针对现有污泥固化技术存在的固化养护时间长、低温条件下固化效能低等问题。研究提出污泥快速（3 d）固化技术,采用响应曲面分析方法,重点考察了石灰、组分A、硅酸盐水泥、粉煤灰和温度等5因素对固化效能的综合影响,研究结果表明,石灰、组分A、硅酸盐水泥、粉煤灰和养护温度等因素对3 d固化体的无侧限抗压强度和含水率的线性效应显著,石灰和组分A、石灰和养护温度对无侧限抗压强度的交互影响显著,石灰和粉煤灰、组分A和养护温度、硅酸盐水泥和粉煤灰对含水率的交互影响显著;得出了5因素对固化体3 d无侧限抗压强度和含水率影响的定量模型,可对污泥快速固化进行优化和预测;并利用XRD和SED对污泥固化块的化学成分和微观结构进行了分析。     

固体废弃物对新拌水泥浆体密实度与强度的影响

研究固体废弃物(石灰石粉、粉煤灰、赤泥和矿渣)作掺合料颗粒体系与新拌浆体填充密实性能的关系;分析了在水胶比为0.3时,以上4种固体废弃物以不同比例等质量取代水泥的净浆强度。实验结果表明,石灰石粉、粉煤灰、赤泥作为掺合料,能够改善胶凝材料的颗粒级配,填充新拌水泥浆体中的孔隙,使浆体更为密实,并且对其净浆的强度有利。     

高稳定性污泥蛋白发泡剂的发泡特性及应用研究

以污泥蛋白为实验材料,通过加入不同量的稳定剂GP-1,配制成高稳定性污泥蛋白发泡剂,并对高稳定性污泥蛋白发泡剂的发泡特性和影响因素进行研究。结果表明,以污泥蛋白10 mL、水90 mL、GP-1 0.4 g配方组合为研究对象,所制备的泡沫初始体积为770 mL,泡沫泌水时间大于15 h,泡沫半衰期大于64 h,泡沫综合发泡能力为2.2×10⁶ mL·min,泡沫的最佳搅拌时间为5 min,泡沫的泌水时间和泡沫的半衰期都是随着温度的上升而下降,在pH为3～13时泡沫稳定。经过对高稳定性污泥蛋白发泡剂发泡特性研究以及对水泥的胶凝时间、特性进行比较,研制出污泥蛋白泡沫混凝土发泡剂,并制备污泥蛋白泡沫混凝土块;结果表明,当污泥蛋白泡沫混凝土发泡剂的用量分别为0、6、6.8、7.6、8.4和9.2 mL,水泥为200 g时,制备泡沫混凝土块,其密度由2.07 g/cm³下降到0.34 g/cm³,体积由130 cm³ 上升到755 cm³;在泡沫混凝土块脱模后的第1 d、第7 d、第28 d分别称量他们的重量变化情况,结果表明,泡沫混凝土块第1 d和第7 d无重量变化,第28 d的重量明显减轻。该研究为污泥蛋白研制成为泡沫混凝土发泡剂,并应用于屋面隔热、保温建立前期基础。     

Influence of thermally activated paper sludge on the behaviour of blended cements subjected to saline and non-saline environments

Background, aim and scope  One of the problems to affect Portland cement matrices is low resistance to aggressive agents, due principally to the presence of a high content of portlandite in the hydrated cements. Pozzolanic materials have played an important role in the improving the durability of cement-based materials for decades. This work studies the behaviour of cement mortar matrices blended with 10% calcined paper sludge (source for metakaolinite) and exposed to different environmental conditions (saline and non-saline environments) after 6 and 12 months of exposure. Materials and methods  Two cements were studied: an ordinary Portland cement (CEM 1, 42.5R), acting as reference cement, and a blended cement formulated by mixing 90% (by mass) of CEM 1, 42.5R with 10% (by mass) of paper sludge calcined at 700°C for 2 h. The specimens were exposed 1 year to saline and non-saline environments. All the mineralogy samples were studied through X-ray diffraction and scanning electron microscopy (SEM) equipped with an energy dispersive X-ray analyser. The in-depth study on ionic mobility was performed on samples subjected to natural exposure (coast and tableland) for 6 and 12 months. Results  Portland cement was composed of quartz, calcite, calcium hydroxide and tobermorite gels. The pozzolanic cement (10% calcined paper sludge) is of the same composition but a high calcite concentration and barium carbonate. SEM analysis from coastline show deposits of variable composition. The deposits are identified on the surface of different mineral components. The minerals from tableland are much fractured, i.e. calcite and feldspars. Inside the fractures, the deposits and the ions are located and trapped superficially. Discussion  SEM analysis of control cement Portland and 10% calcined paper sludge shows deposits on quartz and calcite with a very high concentration of Pb, Zn, Cl and barium sulphate. A very porous aspect is due to the presence of the different aggregate types. This porous configuration permits retention of the ion environment. The pozzolanic cement in environments subject to the saline mist favours the retention and transport of ions observed. Something similar also happens with the increase in exposure to outdoor weather. Non-saline samples show temperature changes (ice or thaw cycles). Barium retention is kept on the surface in fracture lines by the gelification processes. In general, it may be inferred that an increase in exposure time increases the diffusion of ions towards test piece interiors. The chemical composition profiles show that the ions present different penetration speeds. Conclusions  The results indicate the better vulnerability of pozzolanic cements from calcined paper sludge in saline and non-saline environments. The cements with a 10% addition of calcined paper sludge favour retention and transport of ion has been observed. Recommendations and perspectives  Today, projects are centred on a new recycling line for industrial waste of this kind, with special attention on its incorporation in cement manufacture as a pozzolanic material, setting the most appropriate activation conditions of the mineralogical compound in this waste (kaolinite and metakaolinite) and taking them as a starting point for this project. The use of pozzolanic cement with 10% addition of calcined paper sludge is a system which favours ionic retention.     

The reuse of biosludge as an adsorbent from a petrochemical wastewater treatment plant

Biosludge was obtained from a petrochemical industry's biological wastewater treatment plant. Zinc chloride (ZnCl2) was used as a sludge activation agent during the pyrolytic process. Scanning electron microscope (SEM) image photographs, element composition, surface functional group, and pore structure were analyzed for the sludge adsorbent characteristics. Results indicated the proper ZnCl2-immersed concentration, pyrolytic temperature, and time could produce adsorbent from the biosludge. The optimal conditions for a larger surface area adsorbent were 3 M ZnCl2-immersed sludge pyrolyzed at 600 degrees C for 30 min and washed with 3 N hydrochloric acid (HCl) solution and distilled water. The predominant pore size of the sludge adsorbent was the mesopore.     

Glazed tiles manufactured from incinerated sewage sludge ash and clay

Sewage sludge incineration is applied extensively in highly populated cities as a final sludge treatment. In this study, incinerated ash was utilized as an additive to clay to manufacture glaze tiles. Four different amounts of ash (0, 15, 30, and 45%) were added, and five glaze concentrations (0.03, 0.06, 0.1, 0.15, and 0.2 g/cm2) were applied on the surface of biscuit tiles to study the effects of ash additive and glaze concentration on properties of fired samples. Sewage sludge was dehydrated and incinerated into ash at 800 degrees C. Subsequently, tile specimens were manufactured and fired at 800 degrees C to make biscuit tiles. Fritted glazes and iron oxide were used as the fundamental glaze and colorant, respectively. Finally, glaze was applied on the surface of biscuit tiles and then fired at 1050 degrees C to sinter them into glazed tile specimens. Tests were performed to analyze properties, including water absorption, firing shrinkage, weight loss on ignition, abrasion resistance, bending resistance, acid-alkali resistance, and aging resistance on specimens of glaze tile. To further understand more about the microstructural behavior of glazed tile specimens, analysis of energy dispersive spectrometer, scanning electron microscopy, and X-ray were carried out in this study.     

A comparison between sludge ash and fly ash on the improvement in soft soil

In this study, the strength of soft cohesive subgrade soil was improved by applying sewage sludge ash as a soil stabilizer. Test results obtained were compared with earlier tests conducted on soil samples treated with fly ash. Five different proportions of sludge ash and fly ash were mixed with soft cohesive soil, and tests such as pH value, compaction, California bearing ratio, unconfined compressive strength (UCS), and triaxial compression were performed to understand soil strength improvement because of the addition of both ashes. Results indicate that pH values increase with extending curing age for soil with sludge ash added. The UCS of sludge ash/soil were 1.4-2 times better than untreated soil. However, compressive strength of sludge ash/soil was 20-30 kPa less than fly ash/soil. The bearing capacities for both fly ash/soil and sludge ash/soil were five to six times and four times, respectively, higher than the original capacity. Moreover, the cohesive parameter of shear strength rose with increased amounts of either ash added. Friction angle, however, decreased with increased amounts of either ash. Consequently, results show that sewage sludge ash can potentially replace fly ash in the improvement of the soft cohesive soil.     

染料废水混凝污泥免烧砖浸出毒性的研究

染料废水混凝污泥处理处置及资源化利用对环境保护和染料生产企业的可持续发展有重要意义。依据《固体废物浸出毒性浸出方法水平振荡法》(HJ 557—2009)和《固体废物浸出毒性浸出方法硫酸硝酸法》(HJ/T 299—2007)对污泥和污泥免烧砖制备浸出液,用分光光度法和化学滴定法测定了浸出液中主要有机污染物(对硝基苯胺、苯胺、间苯二胺和丙烯腈)的含量。结果表明:(1)硅酸盐水泥(样品标记为42.5R、水泥1、水泥2)和铝酸盐水泥(样品标记为CA)对苯胺和间苯二胺的固化效果差别不大;水泥2对对硝基苯胺的固化效果最好;42.5R对丙烯腈的固化效果不如其他3种水泥。(2)对硝基苯胺、苯胺、间苯二胺、丙烯腈经水泥固化后,其浸出毒性均降低。     

厌氧序批式反应器中丝状颗粒污泥的形成

以葡萄糖为基质,研究浮动盖式ASBR中颗粒污泥的形成。实验结果表明,污泥在120 d时完全颗粒化,颗粒污泥具有良好的沉降性能(25 m/h)及良好的产甲烷活性,甲酸、乙酸、丙酸及丁酸最大代谢活性分别达到0.216、0.825、0.237和0.796 g COD/(g VSS.d)。电镜扫描(SEM)发现,整个污泥结构均一,均由丝状菌构成。     

Thermal detoxification of hazardous metal sludge by applied electromagnetic energy

Industrial wastewater sludge was treated by microwave processes to enhance the stabilization of laden copper. The effects of additives, processing time, microwave adsorbents, moisture content, reaction atmosphere, and cooling gas were investigated. The stabilization results were significantly enhanced by metal powder additives, prolonged microwave processing time, proper moisture content, the addition of carbonaceous materials, and a reaction environment with inert gas. It was also found that the moisture content would increase the homogeneity of applied microwave energy, and thus achieve a better overall efficiency between stabilizing agents and copper. The added metal powders may reduce Cu(II) to Cu(0) in the sludge or TCLP. The resulting thermal energy of microwave radiation, and microarcing process and the oxidation heat of Al powder may also assist the transformation of Cu(II) into CuO and CuAl2O4 phases. Part of the sludge was vitrified within inert gas environment when the processing time was longer than 18 min and active carbon dosage was more than 3g. Reduction reactions also occurred in the hybrid microwave processes, leading to the reduction of sulfates and metal ions, and the formation of Cu2S and FeS. Moreover, the microwave radiation can also enhance the feasibility of co-treating of inorganic and organic solid waste.     

The Reuse of Biosludge as an Adsorbent from a Petrochemical Wastewater Treatment Plant

Abstract

Biosludge was obtained from a petrochemical industry’s biological wastewater treatment plant. Zinc chloride (ZnCl₂) was used as a sludge activation agent during the pyrolytic process. Scanning electron microscope (SEM) image photographs, element composition, surface functional group, and pore structure were analyzed for the sludge adsorbent characteristics. Results indicated the proper ZnCl₂-immersed concentration, pyrolytic temperature, and time could produce adsorbent from the bio-sludge. The optimal conditions for a larger surface area adsorbent were 3 M ZnCl₂-immersed sludge pyrolyzed at 600 °C for 30 min and washed with 3 N hydrochloric acid (HCl) solution and distilled water. The predominant pore size of the sludge adsorbent was the mesopore.     

Cement paste column for simultaneous removal of fluoride, phosphate, and nitrate in acidic wastewater

Cement paste, a cured mixture of cement and water, was reported to have considerable capacity for fluoride removal. In this study, heavily mixed fluoric acid wastewater from a semiconductor fabrication plant was applied to a column packed with cement paste granules to evaluate its capacity for the removal of fluoride and three other contaminants, phosphate, nitrate, and sulfate, as well as to investigate the interactions between these contaminants and cement components. The column reduced fluoride to remarkably low levels since fluorite was formed at highly elevated concentrations of calcium and the residual fluoride was further sorbed into the amorphous calcium phosphate that precipitated the entire amount of phosphate until breakthrough. The simultaneous removal of sulfate in the earlier stage was followed by significant removal of nitrate in exchange with the gradual release of sulfate. This behavior was explained by the co-precipitation of sulfate with calcium phosphate or calcium aluminate solids and the subsequent substitution of nitrate for the interlayer sulfate of monosulfate. However, the overall removal capacity of cement paste was reduced due to the high effluent loss of calcium and competition for calcium between fluoride and phosphate.     

Characterization of eco-cement paste produced from waste sludges

In this study, marble sludge, sewage sludge, drinking water treatment plant sludge, and basic oxygen furnace sludge were used as replacements for limestone, sand, clay, and iron slag, respectively, as the raw materials for the production of cement in order to produce eco-cement. It was found that it is feasible to use marble sludge to replace up to 50% of the limestone and also that other materials can serve as total replacements for the raw materials typically used in the production of cement. The major components of Portland cement were all found in eco-cement clinkers. The eco-cement was confirmed to produce calcium hydroxide and calcium silicate hydrates during the hydration process, increasing densification with the curing age. The compressive strength (S_c) and microstructural evaluations conducted at 28 d revealed the usefulness of eco-cement. It was observed that the S_c data correlated linearly with the pore volume (P) data at 28 d. The proposed model equation could be represented as S_c = 178-461P (correlation coefficient, R² = 0.96). Two parameters, the large capillary pore volume and the medium capillary pore volume, were evaluated using multiple regression analysis.     

不同来源污泥接种餐厨垃圾厌氧发酵产氢效果研究

在相同接种配比(接种污泥占餐厨垃圾的质量分数为30%)条件下,研究了4种不同来源污泥(压滤污泥、厌氧污泥、曝气污泥和河底淤泥)添加或不添加缓冲剂时对餐厨垃圾厌氧发酵产氢效果的影响.结果发现,在不添加缓冲剂时.4种污泥接种餐厨垃圾厌氧发酵平均产氢量依次为厌氧污泥>河底淤泥>压滤污泥>曝气污泥,接种厌氧污泥的餐厨垃圾平均产氢量最高,达10.11mL(以每克挥发性固体(VS)计,下同);而添加缓冲剂时.4种污泥接种餐厨垃圾厌氧发酵平均产氢量依次为厌氧污泥>曝气污泥>压滤污泥>河底淤泥,接种厌氧污泥的餐厨垃圾平均产氢量也最高,为33.72 mL,且体系pH得以缓冲.