Biodiesel production from vegetable oil and waste animal fats in a pilot plant

In this study, corn oil as vegetable oil, chicken fat and fleshing oil as animal fats were used to produce methyl ester in a biodiesel pilot plant. The FFA level of the corn oil was below 1% while those of animal fats were too high to produce biodiesel via base catalyst. Therefore, it was needed to perform pretreatment reaction for the animal fats. For this aim, sulfuric acid was used as catalyst and methanol was used as alcohol in the pretreatment reactions. After reducing the FFA level of the animal fats to less than 1%, the transesterification reaction was completed with alkaline catalyst. Due to low FFA content of corn oil, it was directly subjected to transesterification. Potassium hydroxide was used as catalyst and methanol was used as alcohol for transesterification reactions. The fuel properties of methyl esters produced in the biodiesel pilot plant were characterized and compared to EN 14214 and ASTM D6751 biodiesel standards. According to the results, ester yield values of animal fat methyl esters were slightly lower than that of the corn oil methyl ester (COME). The production cost of COME was higher than those of animal fat methyl esters due to being high cost biodiesel feedstock. The fuel properties of produced methyl esters were close to each other. Especially, the sulfur content and cold flow properties of the COME were lower than those of animal fat methyl esters. The measured fuel properties of all produced methyl esters met ASTM D6751 (S500) biodiesel fuel standards.     

Biodiesel from lignocellulosic biomass – Prospects and challenges

Biodiesel can be a potential alternative to petroleum diesel, but its high production cost has impeded its commercialization in most parts of the world. One of the main drivers for the generation and use of biodiesel is energy security, because this fuel can be produced from locally available resources, thereby reducing the dependence on imported oil. Many countries are now trying to produce biodiesel from plant or vegetable oils. However, the consumption of large amounts of vegetable oils for biodiesel production could result in a shortage in edible oils and cause food prices to soar. Alternatively, the use of animal fat, used frying oils, and waste oils from restaurants as feedstock could be a good strategy to reduce the cost. However, these limited resources might not meet the increasing demand for clean, renewable fuels. Therefore, recent research has been focused the use of residual materials as renewable feedstock in order to lower the cost of producing biodiesel. Microbial oils or single cell oils (SCOs), produced by oleaginous microorganisms have been studied as promising alternatives to vegetable or seed oils. Various types of agro-industrial residues have been suggested as prospective nutritional sources for microbial cultures. Since the most abundant residue from agricultural crops is lignocellulosic biomass (LCB), this byproduct has been given top-priority consideration as a source of biomass for producing biodiesel. But the biological transformation of lignocellulosic materials is complicated due to their crystalline structure. So, pretreatment is required before they can be converted into fermentable sugar. This article compares and scrutinizes the extent to which various microbes can accumulate high levels of lipids as functions of the starting materials and the fermentation conditions. Also, the obstacles associated with the use of LCB are described, along with a potentially viable approach for overcoming the obstacles that currently preclude the commercial production of biodiesel from agricultural biomass.     

Transesterification reaction of the fat originated from solid waste of the leather industry

The leather industry is an industry which generates a large amount of solid and liquid wastes. Most of the solid wastes originate from the pre-tanning processes while half of it comes from the fleshing step. Raw fleshing wastes which mainly consist of protein and fat have almost no recovery option and the disposal is costly. This study outlines the possibility of using the fleshing waste as an oil source for transesterification reaction. The effect of oil/alcohol molar ratio, the amount of catalyst and temperature on ester production was individually investigated and optimum reaction conditions were determined. The fuel properties of the ester product were also studied according to the EN 14214 standard. Cold filter plugging point and oxidation stability have to be improved in order to use the ester product as an alternative fuel candidate. Besides, this product can be used as a feedstock in lubricant production or cosmetic industry.     

Biodiesel production from waste frying oils and its quality control

The use of biodiesel as fuel from alternative sources has increased considerably over recent years, affording numerous environmental benefits. Biodiesel an alternative fuel for diesel engines is produced from renewable sources such as vegetable oils or animal fats. However, the high costs implicated in marketing biodiesel constitute a major obstacle. To this regard therefore, the use of waste frying oils (WFO) should produce a marked reduction in the cost of biodiesel due to the ready availability of WFO at a relatively low price.In the present study waste frying oils collected from several McDonald’s restaurants in Istanbul, were used to produce biodiesel. Biodiesel from WFO was prepared by means of three different transesterification processes: a one-step base-catalyzed, a two-step base-catalyzed and a two-step acid-catalyzed transesterification followed by base transesterification. No detailed previous studies providing information for a two-step acid-catalyzed transesterification followed by a base (CH₃ONa) transesterification are present in literature. Each reaction was allowed to take place with and without tetrahydrofuran added as a co-solvent. Following production, three different procedures; washing with distilled water, dry wash with magnesol and using ion-exchange resin were applied to purify biodiesel and the best outcome determined. The biodiesel obtained to verify compliance with the European Standard 14214 (EN 14214), which also corresponds to Turkish Biodiesel Standards.     

Thermal valorization of post-consumer film waste in a bubbling bed gasifier

The use of plastic bags and film packaging is very frequent in manifold sectors and film waste is usually present in different sources of municipal and industrial wastes. A significant part of it is not suitable for mechanical recycling but could be safely transformed into a valuable gas by means of thermal valorization. In this research, the gasification of film wastes has been experimentally investigated through experiments in a fluidized bed reactor of two reference polymers, polyethylene and polypropylene, and actual post-consumer film waste. After a complete experimental characterization of the three materials, several gasification experiments have been performed to analyze the influence of the fuel and of equivalence ratio on gas production and composition, on tar generation and on efficiency. The experiments prove that film waste and analogue polymer derived wastes can be successfully gasified in a fluidized bed reactor, yielding a gas with a higher heating value in a range from 3.6 to 5.6 MJ/m³ and cold gas efficiencies up to 60%.     

Environmental and economic analyses of waste disposal options for traditional markets in Indonesia

Waste from traditional markets in Indonesia is the second largest stream of municipal solid waste after household waste. It has a higher organic fraction and may have greater potential to be managed on a business scale compared to household wastes. The attributed reason is that in general the wastes generated from traditional markets are more uniform, more concentrated and less hazardous than waste from other sources. This paper presents the results of environmental and economic assessments to compare the options available for traditional market waste disposal in Indonesia. The options compared were composting in labour intensive plants, composting in a centralised plant that utilised a simple wheel loader, centralised biogas production and landfill for electricity production. The current open dumping practice was included as the baseline case. A life cycle assessment (LCA) was used for environmental analysis. All options compared have lower environmental impacts than the current practice of open dumping. The biogas production option has the lowest environmental impacts. A cost-benefit analysis, which considered greenhouse gas savings, was used for the economic assessment. It was found that composting at a centralised plant is the most economically feasible option under the present Indonesian conditions. The approach reported in this study could be applied for 'a pre-feasibility first cut comparison' that includes environmental aspects in a decision-making framework for developing countries even though European emission factors were used.     

Analyzing alternative bio-waste feedstocks for potential biodiesel production using time domain (TD)-NMR

Production of biodiesel is currently limited due to lack of economically beneficial feedstocks. Suitability of municipal wastewater sludge and olive mill waste as feedstocks for biodiesel production was evaluated. The various bio-waste sources were analyzed for their oil content and fatty acid composition using conventional analyses complemented with time domain (TD)-NMR analysis. TD-NMR, a rapid non-destructive method newly applied in this field, yielded good correlations with conventional methods. Overall biodiesel yields obtained by TD-NMR analysis were 7.05% and 9.18% (dry wt) for olive mill pomace and liquid wastes, and 11.92%, 7.07%, and 4.65% (dry wt) for primary, secondary, and anaerobically stabilized sludge, respectively. Fatty acid analysis indicated fundamental suitability of these agro-industrial waste resources for biodiesel production. Evaluation of bio-waste materials by TD-NMR revealed the potential of this tool to identify waste-oil sources cost effectively and quickly, supporting expansion of a sustainable biodiesel industry in Israel and other regions.     

酶法合成生物柴油的研究进展

生物柴油是一种清洁可再生的生物能源,是石油燃料的理想替代物。酶法合成生物柴油具有提取简单、反应条件温和、醇用量小、甘油易回收和无废物产生等优点。综述了脂肪酶与固定化脂肪酶、全细胞生物催化剂在生物柴油生产中应用的新进展,并对我国生物柴油产业的发展提出了建议。     

Leather Insole with Acupressure Effect: New Perspectives

Some wastes contain many reusable substances of high value. Solid leather waste is one such potential waste which can be converted into value added products. This study attempts to prepare leather insoles with acupressure effect from finished leather wastes and used leather wastes. Leather with acupressure effect (LAE) was fabricated using regenerated leather. LAE was characterized physico-chemically using Fourier transform infrared spectroscopy, thermo gravimetric analysis and scanning electron microscopy. Foot pressure measurements were done using LAE insoles on healthy individuals. Results proved that LAE insoles were able to increase the foot pressure of the wearer and thereby created an acupressure effect in them. Wearing of footwear with LAE insoles were beneficial compared to regular insoles. LAE possessed the required mechanical properties for insole production and it was also biodegradable in nature. The study proves that these composites could be successfully used for the production of cost-effective leather goods and therapeutic footwear. Production of useful byproducts from wastes is income generating and at the same time reduces environmental pollution and a feasible technology for waste recycling has been proved in this study.     

废铜催化剂的综合利用

研究了以湿法回收利用废铜催化剂中的铜、锌制取氧化亚铜和氧化锌的原理以及最佳工艺条件。该工艺可同槽进行浸取、蒸氨、还原、中和水解等操作,生产成本低,产品质量好,工艺过程中无三废排放,具有很好的综合效益。     

Feasibility study for thermal treatment of solid tire wastes in Bangladesh by using pyrolysis technology

In this study on the basis of lab data and available resources in Bangladesh, feasibility study has been carried out for pyrolysis process converting solid tire wastes into pyrolysis oils, solid char and gases. The process considered for detailed analysis was fixed-bed fire-tube heating pyrolysis reactor system. The comparative techno-economic assessment was carried out in US$ for three different sizes plants: medium commercial scale (144 tons/day), small commercial scale (36 tons/day), pilot scale (3.6 tons/day). The assessment showed that medium commercial scale plant was economically feasible, with the lowest unit production cost than small commercial and pilot scale plants for the production of crude pyrolysis oil that could be used as boiler fuel oil and for the production of upgraded liquid-products.     

Proximate composition of household waste and applicability of waste management technologies by source separation in Hanoi,Vietnam

The organic fraction of municipal solid wastes in Southeast Asia, which has a high moisture content, accounts for a large proportion of total waste. Local governments need to pay adequate attention to the composition of wastes to determine alternative waste management technologies. This study proposed the use of a triangle diagram to describe changes in proximate composition and rates of successful source separation of municipal solid waste and to identify technical challenges about alternative waste management technologies such as incineration, composting, and refuse-derived fuel production based on physical and proximate composition analysis of household waste sampled in Hanoi, Vietnam, as a case study. The analysis indicated the effectiveness of different types of source separation as well as different levels of successful achievement of source separation as an adjustment mechanism for the proximate composition of waste. Proper categorization of wastes for source separation is necessary for the appropriate use of alternative waste management technologies. The results showed that, at a source separation rate of just greater than 0.52 in a three-way separation scheme, the waste separated as combustible waste would be suitable for incineration with energy recovery. Based on well-designed schemes of source separation, alternative waste management technologies can be applied.     

Perspectives for pilot scale study of RDF in Istanbul,Turkey

Municipal solid waste (MSW) is one of the most important environmental problems arising from rapid urbanization and industrialization. The use of alternative fuels in rotary kilns of cement plants is very important for reducing cost, saving fossil fuels and also eliminating waste materials, accumulated during production or after using these materials. Cement industries has an important potential for supplying preferable solutions to the waste management. Energy recovery from waste is also important for the reduction of CO₂ emissions.This paper presents an investigation of the development of refuse derived fuel (RDF) materials from non-recycling wastes and the determination of its potential use as an alternative fuel in cement production in Istanbul, Turkey. RDF produced from MSW was analyzed and its effects on cement production process were examined. For this purpose, the produced RDF was mixed with the main fuel (LPG) in ratios of 0%, 5%, 10%, 15% and 20%. Then chemical and mineralogical analyses of the produced clinker were carried out. It is believed that successful results of this study will be a good example for municipalities and cement industries in order to achieve both economic and environmental benefits.     

Enrichment of elements in industrial waste incineration bottom ashes obtained from three different types of incinerators,as studied by ICP-AES and ICP-MS

The elemental composition of the industrial waste incineration bottom ash (IWIBA) samples collected from three different types of incinerator with different kinds of wastes were compared. The major-to-ultratrace elements in the IWIBA samples were determined by inductively coupled plasma atomic emission spectrometry (ICP-AES) and inductively coupled plasma mass spectrometry (ICP-MS). As a result, ca. 40 elements in the concentration range from milligrams per gram to submicrograms per gram could be determined with relative standard deviations of less than 5%. The IWIBA sample from petrochemical wastes contained lower concentrations of the elements, because fewer mineral constituents were contained in the input waste materials. On the contrary, the elemental concentrations in the IWIBA sample from industrial solid wastes provided the highest values for most elements, while the elemental compositions of the IWIBA sample from food wastes were similar to those of municipal solid waste incineration bottom ash. In addition, it was found from the analytical results that the levels of various heavy metals such as Cr, Mn, Fe, Ni, Cu, As, Zr, Mo, Sb, Ba, and Pb were higher in the IWIBA samples than in municipal solid waste incineration bottom ash. The enrichment factors of the elements in the IWIBA samples were estimated from the analytical results to compare the elemental distributions in incineration bottom ashes in relation to their mining influence factors, which are the indices for human use of the elements.     

Characterization of char derived from various types of solid wastes from the standpoint of fuel recovery and pretreatment before landfilling

Carbonization is a kind of pyrolysis process to produce char from organic materials under an inert atmosphere. In this work, chars derived from various solid wastes were characterized from the standpoint of fuel recovery and pretreatment of waste before landfilling. Sixteen kinds of municipal and industrial solid wastes such as residential combustible wastes, non-combustible wastes, bulky wastes, construction and demolition wastes, auto shredder residue, and sludges were carbonized at 500 degrees C for 1h under nitrogen atmosphere. In order to evaluate the quality of char as fuel, proximate analysis and heating value were examined. The composition of raw waste had a significant influence on the quality of produced char. The higher the ratio of woody biomass in waste, the higher heating value of char produced. Moreover, an equation to estimate heating value of char was developed by using the weight fraction of fixed carbon and volatile matter in char. De-ashing and chlorine removal were performed to improve the quality of char. The pulverization and sieving method seems to be effective for separation of incombustibles such as metal rather than ash. Most char met a 0.5 wt% chlorine criterion for utilization as fuel in a shaft blast furnace after it was subjected to repeated water-washing. Carbonization could remove a considerable amount of organic matter from raw waste. In addition, the leaching of heavy metals such as chrome, cadmium, and lead appears to be significantly suppressed by carbonization regardless of the type of raw waste. From these results, carbonization could be considered as a pretreatment method for waste before landfilling, as well as for fuel recovery.     

Bio-drying and size sorting of municipal solid waste with high water content for improving energy recovery

Bio-drying can enhance the sortability and heating value of municipal solid waste (MSW), consequently improving energy recovery. Bio-drying followed by size sorting was adopted for MSW with high water content to improve its combustibility and reduce potential environmental pollution during the follow-up incineration. The effects of bio-drying and waste particle size on heating values, acid gas and heavy metal emission potential were investigated. The results show that, the water content of MSW decreased from 73.0% to 48.3% after bio-drying, whereas its lower heating value (LHV) increased by 157%. The heavy metal concentrations increased by around 60% due to the loss of dry materials mainly resulting from biodegradation of food residues. The bio-dried waste fractions with particle size higher than 45 mm were mainly composed of plastics and papers, and were preferable for the production of refuse derived fuel (RDF) in view of higher LHV as well as lower heavy metal concentration and emission. However, due to the higher chlorine content and HCl emission potential, attention should be paid to acid gas and dioxin pollution control. Although LHVs of the waste fractions with size <45 mm increased by around 2× after bio-drying, they were still below the quality standards for RDF and much higher heavy metal pollution potential was observed. Different incineration strategies could be adopted for different particle size fractions of MSW, regarding to their combustibility and pollution property.     

Simulation of a waste incineration process with flue-gas cleaning and heat recovery sections using Aspen Plus

In the present paper, the modeling of a dual-purpose plant for the production of electrical and thermal energy from the heat treatment of solid wastes is presented. Particularly, the process has been modeled by using the Aspen Plus Shell, with the aim of performing a study about the applicability of this software in the simulation of a solid waste incineration process, which involves complex gas-solid reactions where the solids are referred to as "non-conventional". The model is developed to analyze and quantify the expected benefits associated with refuse derived fuel (RDF) thermal utilization; thus attention is focused on the performance of the energy recovery section.     

Incineration of healthcare wastes: management of atmospheric emissions through waste segregation

The amount of atmospheric pollutants emitted through the incineration of healthcare wastes can be estimated using emission factors. Emission factors have been published without including sufficient information about the types of wastes incinerated. This paper reports the first emission factors estimated for the incineration of wastes segregated into different types according to the Portuguese legislation. One controlled-air incinerator without air pollution control devices was used in the research. The main objectives of the study were: (i) to estimate the emission factors for particulate matter, dioxins, heavy metals and gaseous pollutants, according to the type of waste incinerated; (ii) to evaluate the quality of atmospheric emissions; and (iii) to define a methodology for the management of atmospheric emissions, evaluating the influence of type of waste incinerated and of the segregation method used on the emitted amounts. It was concluded that: (i) when emission factors are not associated with the type of incinerated mixture, the utility of the emission factors is highly doubtful; (ii) without appropriate equipment to control atmospheric pollution, incineration emissions exceed legal limits, neglecting the protection of human health (the legal limit for pollutant concentrations could only be met for NO(x), all other concentrations were higher than the maximum allowed: dioxins, 93-710 times; Hg, 1.3-226 times; CO, 11-24 times; SO(2), 2-5 times; and HCl, 9-200 times); (iii) rigorous segregation methodologies must be used to minimize atmospheric emissions, and incinerate only those wastes that should be incinerated according to the law. A rigorous segregation program can result in a reduction of the amount of waste that should be incinerated by 80%. A reduction in the quantity of waste incinerated results in a reduction on the amounts of pollutants emitted: particulate matter, 98%; dioxins, 99.5%; As, Cd, Cr, Mn and Ni, respectively, 90%, 92%, 84%, 77% and 92%; Hg and Pb, practically eliminated; SO(2) and NO(x), 93%; and CO and HCl, more than 99%.     

Leaching behaviour of hazardous demolition waste

Demolition wastes are generally disposed of in unlined landfills for inert waste. However, demolition wastes are not just inert wastes. Indeed, a small fraction of demolition waste contains components that are hazardous to human health and the environment, e.g., lead-based paint, mercury-contained in fluorescent lamps, treated wood, and asbestos. The objective of this study is to evaluate the release potential of pollutants contained in these hazardous components when they are mixed with inert wastes in unlined landfills. After identification of the different building products which can contain hazardous elements and which can be potentially pollutant in landfill scenario, we performed leaching tests using three different lysimeters: one lysimeter containing only inert wastes and two lysimeters containing inert wastes mixed with hazardous demolition wastes. The leachates from these lysimeters were analysed (heavy metals, chlorides, sulphates fluoride, DOC (Dissolved Organic Carbon), phenol index, and PAH). Finally, we compared concentrations and cumulative releases of elements in leachates with the limits values of European regulation for the acceptance of inert wastes at landfill. Results indicate that limit values are exceeded for some elements. We also performed a percolation column test with only demolition hazardous wastes to evaluate the specific contribution of these wastes in the observed releases.     

Resource-recovery processes from animal waste as best available technology

Along with the world population increase, meat requirement has been also increasing; thus, massive livestock manure has been released leading to problems due to surplus nutrients. To overcome this situation, we should consider availing some nutrient removal or reuse technology. The commonest way to recover resources from livestock manure is by producing liquid fertilizer and compost. However, some technologies are required to make it easier and safer for transportation and handling of manure fertilizer due to various problems such as poor fertilization quality with low maturity, emission of odor, nutrient loss, and disharmony due to fluctuating seasonal and regional supplies and demands. In this study, available technologies for resource recovery from animal wastes were introduced with economic benefits, and an integrated system was proposed including energy flow. The system consisted of anaerobic digestion or microbial fuel cell, struvite precipitation for P recovery, nitrogen enrichment by mechanical vapor compression distillation, and incineration processes (optional). Consequently, the energy output from the system could be sufficient for operating the entire system without the need for extra energy input.