Utilization of textile effluent wastewater treatment plant sludge as brick material

In the present work, the feasibility of using sludge generated in wastewater treatment plants of textile industry as a partial replacement for clay in the conventional brick manufacturing process is examined. Physico-chemical properties of the sludge and clay were studied. The characteristics of bricks with replacement of sludge (0–50 %) with an increment of 3 % were determined. All the brick samples satisfied the requirements of Indian Standards norms in terms of weight loss on ignition. The bricks with sludge up to 15 % satisfied the prescribed norms for compressive strength and water absorption. Results also showed that the brick weight loss on ignition was mainly attributed to the organic matter content in the sludge being burnt off during the firing process. The characteristics of bricks such as efflorescence, density and weight loss on ignition for bricks with replacement of clayey soil with textile sludge up to 15 % also satisfied the requirements of the Indian Standard. Thus, textile sludge up to 15 % can be effectively added to make brick material.     

Effects of using arsenic–iron sludge wastes in brick making

The arsenic–iron sludge generated in most of the treatment systems around the world is discharged into the nearest watercourse, which leads to accumulative rise of arsenic and iron concentrations in water. In this study, attempts were made to use the arsenic–iron sludge in making bricks and to analyze the corresponding effects on brick properties. The water treatment plant sludge is extremely close to brick clay in chemical composition. So, the sludge could be a potential substitute for brick clay. This study involved the addition of sludge with ratios 3%, 6%, 9% and 12% of the total weight of sludge–clay mixture. The physical and chemical properties of the produced bricks were then determined and evaluated and compared to control brick made entirely from clay. Results of different tests indicated that the sludge proportion and firing temperature were the two key factors in determining the quality of bricks. The compressive strength of 3%, 6%, 9% and 12% sludge containing brick samples were found to be 14.1 MPa, 15.1 MPa, 9.4 MPa and 7.1 MPa, respectively. These results indicate that the compressive strength of prepared bricks initially increased and then decreased with the increase of sludge proportion. Leaching characteristics of burnt bricks were determined with the variation of pH at a constant temperature. The optimum amount of sludge that could be mixed with clay to produce good bonding of clay–sludge bricks was found to be 6% (safely maximum) by weight.     

Incorporation of sewage sludge in clay brick and its characterization.

This study reports the use of sewage sludge generated from sewage treatment plant (STP) as raw material in a clay brick-making process. The physico-chemical and mineralogical characterization of the sewage sludge and clay were carried out in order to identify the major technological constraints and to define the sludge pretreatment requirements if necessary. Moreover, the effects on processing conditions and/or on changes of typical final characteristics are also evaluated. Bricks were produced with sewage sludge additions ranging from 10 to 40% by dry weight. The texture and finishing of the surface of sludge-amended clay bricks were rather poor. As for the physical and chemical properties, bricks with a sludge content of up to 40 wt.% were capable of meeting the relevant technical standards. However, bricks with more than 30 wt.% sludge addition are not recommended for use since they are brittle and easily broken even when handled gently. A tendency for a general degradation of brick properties with sludge additions was observed due to its refractory nature. Therefore, sludge bricks of this nature are only suitable for use as common bricks, which are normally not exposed to view, because of poor surface finishing.     

Utilization of municipal solid waste incineration (MSWI) fly ash in ceramic brick: product characterization and environmental toxicity

In this study, municipal solid waste incineration (MSWI) fly ash was used as a blending in making ceramic brick based on its characterization and an orthogonal test was performed to determine the optimal mixture ratio of the materials. Besides, the fired bricks made in accordance with the optimal mixture ratio were characterized for performance, phase transformation, microstructure, leaching toxicity of the heavy metals in accordance with GB/T 2542-92 (Detection methods for bricks analysis, China) and by means of XRD, SEM and leaching toxicity analysis. It was found that the optimal mixture ratio of materials (MSWI fly ash:red ceramic clay:feldspar:gang sand) was 20:60:10:10 by mass, and the optimal sintering temperature was 950 °C. Leaching results of heavy metals from sintered bricks were reduced considerably in comparison with those from green bricks prior to sintering process. The results as a whole suggested that utilization of MSWI fly ash in ceramic brick constituted a potential means of adding value.     

Recycling of cathode ray tube panel glasses as aggregates of concrete blocks and clay bricks

While the cathode ray tube (CRT) funnel containing lead could be transported to a smelting facility to recover lead, which could be an available option in domestic, a proper technology to recycle a CRT panel must be developed. Thus, it was suggested that CRT panel glass be used as aggregates of concrete blocks and clay bricks. Samples of blocks and bricks were fabricated with CRT powders and tested to measure their strength and absorption rate to determine their qualities, and environmental soundness was determined by measuring the leaching rate of hazardous metals. For concrete blocks, CRT panel glass powders incorporated as aggregates up to 40 % replacing stone powder was proposed as the proper condition for manufacturing blocks. Around 2 % of CRT panel incorporated into clay brick to substitute Kaoline was suggested to fabricate the best quality of clay brick. Results of leaching test met the criteria with much less concentration of hazardous metals, even lead compound containing in the CRT funnel. To conclude, the use of CRT panel powder after crushing it to the proper size as an aggregate of concrete blocks or clay bricks could be one of the appropriate alternatives to recycle for CRT glass waste being generated drastically in a short term.     

Recovery of municipal waste incineration bottom ash and water treatment sludge to water permeable pavement materials

Water treatment plant sludge and municipal solid waste incinerator bottom ash are non-hazardous residues, and they can be reprocessed to produce useful materials for city public works. In this study, an effort was endeavored to investigate the properties of water permeable bricks made of water treatment sludge and bottom ash without involving an artificial aggregate step. The water treatment plant sludge was dried and ground, and the bottom ash was subjected to magnetic separation to remove ferrous metals. Both sludge and bottom ash were ground and sieved to a size of <2mm. Different contents of water treatment sludge (70-95% by weight) were mixed with bottom ash and the blocks were molded under a pressure of 110 kg/cm2. Thereafter, the molded blocks were sintered at temperatures of 900-1200 degrees C for 60-360 min. The compressive strength, permeability and water absorption rate of the sintered brick were examined and compared to relevant standards. The amount of bottom ash added in the mixture with water treatment sludge affects both the compressive strength and the permeability of the sintered bricks. The two effects are antonymous as higher bottom ash content will develop a beehive configuration and have more voids in the brick. It is concluded that a 20% weight content of bottom ash under a sintering condition of 1150 degrees C for 360 min can generate a brick with a compressive strength of 256 kg/cm2, a water absorption ratio of 2.78% and a permeability of 0.016 cm/s.     

Effects of recycled glass substitution on the physical and mechanical properties of clay bricks

In this study, wasted glasses from structural glass walls up to 45 wt.% were added into clay mixtures in brick manufacturing process. Physical and mechanical properties of clay bricks were investigated as functions of the wasted glass content and the firing temperature. The results indicated that with proper amount of wasted glasses and firing temperature, clay bricks with suitable physical and mechanical properties could be obtained. The compressive strength as high as 26–41 MPa and water absorption as low as 2–3% were achieved for bricks containing 15–30 wt.% of glass content and fired at 1100 °C. When the glass waste content was 45 wt.%, apparent porosity and water absorption was rapidly increased.     

Stabilization/solidification of ashes in clays used in the manufacturing of ceramic bricks.

This paper presents the results of the lixiviation of metals from different mixtures of fly and bottom ashes that have been stabilized and solidified in clays used in the manufacture of bricks. The ashes used for this study were obtained from a Hoffmann-type brick furnace adapted for the incineration of municipal solid waste during the manufacturing of ceramic bricks. The ashes were stabilized in clay in different proportions of clay:ash mix (99:1, 95:5, 90:10, 80:20 and 60:40). Such mixes were used to manufacture bricks that were calcined at a temperature ranging from 50 to 1100 degrees C. The clay, ashes and manufactured bricks were characterized using X-ray diffraction, fluorescent X-ray, thermogravimetry, differential thermal analysis, atomic absorption spectroscopy and scanning electronic microscopy. In addition, toxicity characteristic leaching procedure lixiviation tests were performed according to the EPA 1311 method for the determination of heavy metals. The results showed an affinity between clay and ash, and also that the bricks manufactured with these mixtures present low lixiviation levels. The tests also showed the highest decrease in the concentration of arsenic, nickel, chromium, zinc and silver for 99:1 mixtures. The 95:5 mixture was found to be the most favourable for the stabilization (greater concentration decrease) of lead and cadmium. Selenium was the metal with the lowest concentration change whereas arsenic, nickel, chromium, zinc and cadmium showed the greatest concentration change in all mixtures, with the exception of cadmium in the mixture 99:1.     

Brick production with dredged harbour sediments. An industrial-scale experiment

A volume of 600.000 m3 harbour sediments is annually dredged out of the harbour basin of Bremen to maintain a certain water depth. Because of its perpetual availability, homogeneity and mineralogical, petrographic and chemical composition, the sediment is regarded as a suitable raw material for brick production. A pilot experiment was conducted at a full-scale industrial brickworks. During production, the environmental standards concerning waste-water treatment and the quality of exhausted gas were sufficiently fulfilled. Bricks specified as "building bricks" were produced according to German industrial standards. The parameters pH-value and grain size were varied in leaching tests performed on the bricks as both parameters are likely to change in the course of the brick's life cycle. The leaching data showed that As was stabilised and heavy metals were immobilised in a way that the bricks were not (hazardous to soil or groundwater) neither by their use, for example, in masonry, nor afterwards, when they will be deposited as mineral demolition mass.     

Chemical and microbiological stability of waste sludge from paper industry intended for brick production.

Due to its chemical composition, waste sludge generated in the paper industry may be used as a raw material for brick production. Brick manufacture is limited to the warmer months of the year whereas sludge is produced continuously by different effluent treatment devices. Therefore, it has to be stored until further processing. For this reason, it is essential that it is not subject to significant chemical and microbiological decomposition during storage. In the experiment, sludge from a tissue paper mill was tested for its stability. It was stored for several weeks during winter and summer periods in a pile, 2 m in height, in an open but covered store. Different leachable organic and inorganic compounds indicating possible ongoing deterioration processes, as well as pH value, redox potential, temperature, humidity and dry matter content were evaluated weekly in water extracts of homogenized sludge samples. According to the test results, the material may be considered to be chemically and microbiologically stable as there was practically no emission of odorous and toxic compounds such as H2S, NH3 and butyric acid despite prolonged storage times and elevated environmental temperatures. All the microbial species identified in the sludge during storage belong to the typical microflora of the environment.     

Recycling of electrolytic manganese solid waste in autoclaved bricks preparation in China

China has played a dominant role in global electrolytic manganese metal (EMM) production, accounting for over 98 % of the total world capacity since 2008. However, with the rapid development of the EMM industry and depletion of mineral ores, electrolytic manganese solid waste (EMSW) is piling up, so more large-scale landfills are needed. The environmental problems generated by EMSW pose severe threats to soil and ground water, and have become the hot issues in society. The aim is to consume and recycle EMSW, and the primary route is to make autoclaved bricks. However, less attention has been given to the procedure and strength-forming mechanism of EMSW bricks, not to mention the production line of the brick. On the basis of physical and chemical property analysis, the pretreatment process of EMSW was indispensable to solidify/stabilize the heavy metals, such as Mn, Zn, Cd, Pb, etc.. This paper expatiated on the procedure of making EMSW autoclaved bricks, analyzed in detail the strength formed by different cementitious materials with cement properties, and introduced the practical engineering of EMSW autoclaved bricks. The results showed that the pretreatment process with quicklime was effective in solidifying/stabilizing the heavy metals. The compressive strength of EMSW bricks reached 10.05 MPa when quicklime 9 % (w/w) added. Cement may be an ideal cementitious material to create EMSW bricks of high strength in experiments and on the production line. Quicklime and cement used simultaneously produced a lower strength than that when adding cement alone because the gypsum from EMSW and an alkali could generate deleterious effects, e.g., expansion or burst. In the production line of EMSW bricks, an appropriate mix proportion to make high-quality autoclaved bricks was determined: EMSW 30–40 %, cement 10–20 %, and aggregates 40–60 %. The low content of heavy metals tested by toxicity leaching may deduce that the EMSW autoclaved bricks have low environmental risk. However, long-term environmental risk evaluation will be needed, requiring more tests and leaching modeling. Employing EMSW to make high-quality autoclaved bricks may be a promising waste-to-resource strategy.     

Effects of cement on redistribution of trace metals and dissolution of organics in sewage sludge and its inorganic waste-amended products

The suitability of using cement-stabilized sludge products as artificial soils in earth works was evaluated. The sludge products investigated were cemented sludge, cement-treated clay-amended sludge (SS+MC), and cement-treated copper slag-amended sludge (SS+CS). The leachability of lead (Pb), zinc (Zn), copper (Cu), and chromium (Cr) were assessed using the sequential extraction technique, toxicity characteristic leaching procedure (TCLP), NEN 7341 availability test, and column leaching test. The results indicated that Zn leachability was reduced in all the cement-stabilized sludge products. In contrast, Cu was transferred from the organic fraction to the readily leachable phases in the cement-stabilized sludge products and therefore exhibited increased leachability. The increased Cu leachability could be attributed to dissolution of humic substances in the sludge as a result of elevated pH. Good correlation between dissolved organic carbon (DOC) and heavy metal leaching from the cement-stabilized sludge products was observed in the column leaching experiment. Even with a cement percentage as small as 12.5%, calcium silicate hydrate (C-S-H) was formed in the SS+MC and SS+CS products. Inclusion of the marine clay in the SS+MC products could reduce the leaching potentials of Zn, and this was the great advantage of the marine clay over the copper slag for sludge amendment.     

Reuse of textile effluent treatment plant sludge in building materials

This study examines the potential reuse of textile effluent treatment plant (ETP) sludge in building materials. The physico-chemical and engineering properties of a composite textile sludge sample from the southern part of India have been studied. The tests were conducted as per Bureau of Indian Standards (BIS) specification codes to evaluate the suitability of the sludge for structural and non-structural application by partial replacement of up to 30% of cement. The cement-sludge samples failed to meet the required strength for structural applications. The strength and other properties met the Bureau of Indian Standards for non-structural materials such as flooring tiles, solid and pavement blocks, and bricks. Results generally meet most ASTM standards for non-structural materials, except that the sludge-amended bricks do not meet the Grade NW brick standard. It is concluded that the substitution of textile ETP sludge for cement, up to a maximum of 30%, may be possible in the manufacturing of non-structural building materials. Detailed leachability and economic feasibility studies need to be carried out as the next step of research.     

Towards zero industrial waste: Utilisation of brick dust waste in sustainable construction

Laboratory investigations were carried out to establish the potential utilisation of brick dust (BD) in construction. The dust is a waste material from the cutting of fired clay bricks. Currently, the disposal of the dust is a problem to the brick fabrication company, and hence an environmental pollution concern. The dust was stabilised either used on its own or in combination with Pulverised Fuel Ash (PFA), a by-product material from coal combustion. The traditional stabilisers of lime and/or Portland Cement (PC) were used as controls. The main aim was to use a sustainable stabiliser material, where these stabilisers were partially replaced with Ground Granulated Blastfurnace Slag (GGBS), a by-product material from steel manufacture. Compacted cylinder test specimens were made at typical stabiliser contents and moist cured for up to 56 days prior to testing for compressive and California Bearing Ratio (CBR) strength tests, and to linear expansion during moist curing and subsequent soaking in water. The results obtained showed that partial substitution of the dust with PFA resulted in stronger material compared to using it on its own. The blended stabilisers achieved better performance. These results suggest technological, economic as well as environmental advantages of using the brick dust and similar industrial by-products to achieve sustainable infrastructure development with near zero industrial waste.     

氯化铵浸取法回收盐泥中的镁

以盐泥为原料,采用氯化铵浸取回收盐泥中的Mg²⁺,以浸取液和回收的氨反应制取氢氧化镁产品。考察了盐泥浆液固含量、浸取时间、物料比（氯化铵与盐泥中氢氧化镁的摩尔比）等工艺条件对Mg²⁺浸取率的影响,并以比表面积为考察指标进行正交实验,确定氢氧化镁的最佳制备条件。实验结果表明：在盐泥浆液固含量为248 g/L、浸取时间为100 min、物料比为2.3的条件下,Mg²⁺浸取率为75.0%;在n（MgCl₂）:n（NH₄Cl）=0.5、氨水浓度3 mol/L、氨水滴加速率 0.8 mL/min、反应温度 90 ℃的最佳条件下,制备的氢氧化镁的比表面积为17.87 m²/g,粒径约为3 μm。该工艺简单可行,为盐泥的综合利用提供了新的思路。     

Effect of organic residues addition on the technological properties of clay bricks

The objective of this study is to investigate the utilization potential of several organic residues in clay bricks. Sawdust, tobacco residues, and grass are widespread by-products of industrial and agricultural processes in Turkey. These residue materials have long cellulose fibres. Sawdust and tobacco residues generally are used as fuel, and the grass is utilized for agricultural purposes. The insulation capacity of brick increases with the increasing porosity of the clay body. Combustible, organic types of pore-forming additives are most frequently used for this purpose. For this reason, increasing amounts of organic residues (0%, 2.5%, 5% and 10% in wt.) were mixed with raw brick-clay. All samples were fired at 900 degrees C. Effects on shaping, plasticity, density, and mechanical properties were investigated. The organic residue additions were found to be effective for pore-forming in the clay body with the clay maintaining acceptable mechanical properties. It was observed that the fibrous nature of the residues did not create extrusion problems. However, higher residue addition required a higher water content to ensure the right plasticity. As a result, sawdust, tobacco residues, and grass can be utilized in an environmentally safe way as organic pore-forming agents in brick-clay.     

Degradation of chlorinated dioxin in denitrifying activated sludge from leachate treatment plant of a landfill

The degradation rate of dioxins added to the activated sludge from a leachate treatment plant of a landfill under denitrification conditions was estimated using six bioreactors. Over 99% of the added dioxins (600ng) were degraded within 7 days. Furthermore, continuous cultivation was carried out for 1 month. The activated sludge degraded 600ng of dioxins (that is, all of the added dioxins) placed in each reactor every 7 days, and this activity was maintained for 35 days. Under aerobic conditions with this sludge, the dioxins were not degraded in 7 days, but 90% of the 600ng of dioxins was degraded in 35 days. The high level of activity observed in the present study may only occur under anaerobic conditions, especially under denitrifying conditions.     

Use of wastes derived from earthquakes for the production of concrete masonry partition wall blocks

Utilization of construction and demolition (C&D) wastes as recycled aggregates in the production of concrete and concrete products have attracted much attention in recent years. However, the presence of large quantities of crushed clay brick in some the C&D waste streams (e.g. waste derived collapsed masonry buildings after an earthquake) renders the recycled aggregates unsuitable for high grade use. One possibility is to make use of the low grade recycled aggregates for concrete block production. In this paper, we report the results of a comprehensive study to assess the feasibility of using crushed clay brick as coarse and fine aggregates in concrete masonry block production. The effects of the content of crushed coarse and fine clay brick aggregates (CBA) on the mechanical properties of non-structural concrete block were quantified. From the experimental test results, it was observed that incorporating the crushed clay brick aggregates had a significant influence on the properties of blocks. The hardened density and drying shrinkage of the block specimens decreased with an increase in CBA content. The use of CBA increased the water absorption of block specimens. The results suggested that the amount of crushed clay brick to be used in concrete masonry blocks should be controlled at less than 25% (coarse aggregate) and within 50-75% for fine aggregates.     

Recycling and recovery routes for incinerated sewage sludge ash (ISSA): A review

The drivers for increasing incineration of sewage sludge and the characteristics of the resulting incinerated sewage sludge ash (ISSA) are reviewed. It is estimated that approximately 1.7 million tonnes of ISSA are produced annually world-wide and is likely to increase in the future. Although most ISSA is currently landfilled, various options have been investigated that allow recycling and beneficial resource recovery. These include the use of ISSA as a substitute for clay in sintered bricks, tiles and pavers, and as a raw material for the manufacture of lightweight aggregate. ISSA has also been used to form high density glass–ceramics. Significant research has investigated the potential use of ISSA in blended cements for use in mortars and concrete, and as a raw material for the production of Portland cement. However, all these applications represent a loss of the valuable phosphate content in ISSA, which is typically comparable to that of a low grade phosphate ore. ISSA has significant potential to be used as a secondary source of phosphate for the production of fertilisers and phosphoric acid. Resource efficient approaches to recycling will increasingly require phosphate recovery from ISSA, with the remaining residual fraction also considered a useful material, and therefore further research is required in this area.     

酸浸出法回收冶金污泥中的有价金属

采用二次酸浸出的方法回收镍钴湿法冶金工业污泥中的有价金属。先采用水和硫酸作为浸出剂浸出Mg和Na,最佳工艺条件为浸出液的pH 7.5、浸出时间5 min、浸出剂体积与干污泥质量的比(ω)为10 mL/g。再采用硫酸作为浸出剂、焦亚硫酸钠作为还原剂进行二次酸浸,在硫酸与污泥质量比为1.3、焦亚硫酸钠与污泥质量比为0.3、ω为5 mL/g、浸出温度85℃、浸出时间20 min的最佳工艺条件下,Co、Ni、Cu、Mn和Zn的浸出率分别达92.45%、93.48%、89.52%、97.78%和94.79%。经XRD表征,浸出后污泥中未见原污泥中的矿物相,说明原污泥中的矿物几乎全部被溶解。