High time-resolved measurements of organic air toxics in different source regimes

High time-resolved (HTR) measurements can provide significant insight into sources and exposures of air pollution. In this study, an automated instrument was developed and deployed to measure hourly concentrations of 18 gas-phase organic air toxics and 6 volatile organic compounds (VOCs) at three sites in and around Pittsburgh, Pennsylvania. The sites represent different source regimes: a site with substantial mobile-source emissions; a residential site adjacent to a heavily industrialized zone; and an urban background site. Despite the close proximity of the sites (less than 13 km apart), the temporal characteristic of outdoor concentrations varied widely. Most of the compounds measured were characterized by short periods of elevated concentrations or plume events, but the duration, magnitude and composition of these events varied from site to site. The HTR data underscored the strong role of emissions from local sources on exposure to most air toxics. Plume events contributed more than 50% of the study average concentrations for all pollutants except chloroform, 1,2-dichloroethane, and carbon tetrachloride. Wind directional dependence of air toxic concentrations revealed that emissions from large industrial facilities affected concentrations at all of the sites. Diurnal patterns and weekend/weekday variations indicated the effects of the mixing layer, point source emissions patterns, and mobile source air toxics (MSATs) on concentrations. Concentrations of many air toxics were temporally correlated, especially MSATs, indicating that they are likely co-emitted. It was also shown that correlations of the HTR data were greater than lower time resolution data (24-h measurements). This difference was most pronounced for the chlorinated pollutants. The stronger correlations in HTR measurements underscore their value for source apportionment studies.     

Screening-level Assessment of Airborne Carcinogen Risks from Uncontrolled Waste Sites

This report presents screening-level estimates of the general level of cancer risks arising from air emission from uncontrolled waste sites. Twenty-five National Priorities List sites were chosen randomly and airborne cancer risks estimated for each site in terms of risk to the maximally exposed individual (MEI risk), average individual risk (AEI risk), and population incidence. The estimates were developed using the EPA Human Exposure Model using assumptions on the rate and toxicity of site emissions.

MEIrisks ranged from 4 × 10^-9 to 1 × 10^-6 with an average of about 5 × 10^-7. AEI risks for individuals residing within four miles of the sites average about 10^-8, declining significantly for individuals residing at longer distances. Population incidence was low at all sites ranging from 2 × 10^-4 to 1 × 10^-2 cancer cases expected within 60 miles of the sites. Due to the uncertainties in this type of analysis and the underlying study assumptions, these results must be viewed with caution. Nonetheless, some preliminary conclusions can be drawn from the analysis, principally that airborne cancer risks from uncontrolled waste sites are likely to be small in most cases, with the greatest concern being maximally exposed individuals rather than the number of cancer cases expected in the exposed population.     

Apportionment of Ambient Primary and Secondary Pollutants during a 2001 Summer Study in Pittsburgh Using U.S. Environmental Protection Agency UNMIX

Abstract

Apportionment of primary and secondary pollutants during the summer 2001 Pittsburgh Air Quality Study (PAQS) is reported. Several sites were included in PAQS, with the main site (the supersite) adjacent to the Carnegie Mellon University campus in Schenley Park. One of the additional sampling sites was located at the National Energy Technology Laboratory, located ～18 km southeast of downtown Pittsburgh. Fine particulate matter (PM_2.5) mass, gas-phase volatile organic material (VOM), particulate semivolatile and nonvolatile organic material (NVOM), and ammonium sulfate were apportioned at the two sites into their primary and secondary contributions using the U.S. Environmental Protection Agency UNMIX 2.3 multivariate receptor modeling and analysis software. A portion of each of these species was identified as originating from gasoline and diesel primary mobile sources. Some of the organic material was formed from local secondary transformation processes, whereas the great majority of the secondary sulfate was associated with regional transformation contributions. The results indicated that the diurnal patterns of secondary gas-phase VOM and particulate semivolatile and NVOM were not correlated with secondary ammonium sulfate contributions but were associated with separate formation pathways. These findings are consistent with the bulk of the secondary ammonium sulfate in the Pittsburgh area being the result of contributions from distant transport and, thus, decoupled from local activity involving organic pollutants in the metropolitan area.     

Concentrations of volatile organic compounds in an industrial area of Korea

We measured and analyzed daily mean concentrations of volatile organic compounds (VOC) at Ulsan industrial and downtown sites from 3 to 8 June 1997. The industrial site is situated at the boundary of a petrochemical complex and the other is at downtown area in Ulsan. At each site, we collected ambient air samples in passivated stainless-steel containers by using constant flow samplers and analyzed them by a GC-FID. At Ulsan industrial site, the concentrations and their daily variations of total VOC were higher than those at the downtown site. The concentrations of oxygenated hydrocarbons were the highest among seven hydrocarbon groups at both sites. The fraction of C₂–C₅ light hydrocarbon concentrations to C₂–C₉ hydrocarbons at Ulsan industrial site was higher than that in other industrial areas. It suggests that fugitive emissions of light hydrocarbons in Ulsan industrial areas might be higher than those of other industrial areas. Under favorable wind conditions, the influence of industrial emissions of VOC on the downtown hydrocarbon levels was observed.     

Apportionment of Ambient Primary and Secondary Fine Particulate Matter during a 2001 Summer Intensive Study at the CMU Supersite and NETL Pittsburgh Site

Abstract

Gaseous and particulate pollutant concentrations associated with five samples per day collected during a July 2001 summer intensive study at the Pittsburgh Carnegie Mellon University (CMU) Supersite were used to apportion fine particulate matter (PM_2.5) into primary and secondary contributions using PMF2. Input to the PMF2 analysis included the concentrations of PM_2.5 nonvolatile and semivolatile organic material, elemental carbon (EC), ammonium sulfate, trace element components, gas-phase organic material, and NO_x, NO₂, and O₃ concentrations. A total of 10 factors were identified. These factors are associated with emissions from various sources and facilities including crustal material, gasoline combustion, diesel combustion, and three nearby sources high in trace metals. In addition, four secondary sources were identified, three of which were associated with secondary products of local emissions and were dominated by organic material and one of which was dominated by secondary ammonium sulfate transported to the CMU site from the west and southwest. The three largest contributors to PM_2.5 were sec ondary transported material (dominated by ammonium sulfate) from the west and southwest (49%), secondary material formed during midday photochemical processes (24%), and gasoline combustion emissions (11%). The other seven sources accounted for the remaining 16% of the PM_2.5. Results obtained at the CMU site were comparable to results previously reported at the National Energy Technology Laboratory (NETL), located approximately 18 km south of downtown Pittsburgh. The major contributor at both sites was material transported from the west and southwest. Some difference in nearby sources could be attributed to meteorology as evaluated by HYSPLIT model back-trajectory calculations. These findings are consistent with the majority of the secondary ammonium sulfate in the Pittsburgh area being the result of contributions from distant transport, and thus decoupled from local activity involving organic pollutants in the metropolitan area. In contrast, the major local secondary sources were dominated by organic material.     

Accumulation of metals,trace elements and semi-volatile organic compounds on exterior window surfaces in Baltimore

Organic films have been found to develop on window surfaces [Diamond et al., Environmental Science and Technology 34 (2000a) 2900]. The film contains organic compounds that are in dynamic equilibrium with the gas-phase in air, and organic and inorganic compounds and elements associated with deposited air particles. In this study, the exterior surfaces of windows were sampled in downtown and suburban Baltimore, Maryland. Higher concentrations of PCBs, PAH, metals and trace elements were found at downtown than a suburban site. PCBs in the films at downtown sites were dominated by penta and hexa homologue groups and PAH signatures resembled that of vehicle emissions. Twenty-six metals and trace elements were separated into two groups according to their enrichment factors (EF). Ag, Hg, Se, Sb and Zn had EF > 100, suggesting anthropogenic sources of these metals in the films; whereas Fe, Ca, Co, Cr and others had EF <10, suggesting a crustal origin. An unusual profile dominated by deca- and nona- PCBs and relatively higher concentrations of Ag, Hg and Zn may be attributable to emissions from a medical waste incinerator. Dry deposition fluxes of selected metals on windows were 1.4-94 times higher on windows with than without films, indicating that the film increases the dry deposition of particles and their associated chemicals. This implies that film development, which is associated with elevated VOC and SOC emissions to urban air, will increase film development that will, in turn, increase the accumulation of other atmospherically deposited constituents such as metals.     

National review of ambient air toxics observations

Ambient air observations of hazardous air pollutant (HAPs), also known as air toxics, derived from routine monitoring networks operated by states, local agencies, and tribes (SLTs), are analyzed to characterize national concentrations and risk across the nation for a representative subset of the 187 designated HAPs. Observations from the National Air Toxics Trend Sites (NATTS) network of 27 stations located in most major urban areas of the contiguous United States have provided a consistent record of HAPs that have been identified as posing the greatest risk since 2003 and have also captured similar concentration patterns of nearly 300 sites operated by SLTs. Relatively high concentration volatile organic compounds (VOCs) such as benzene, formaldehyde, and toluene exhibit the highest annual average concentration levels, typically ranging from 1 to 5 µg/m³. Halogenated (except for methylene chloride) and semivolatile organic compounds (SVOCs) and metals exhibit concentrations typically 2–3 orders of magnitude lower. Formaldehyde is the highest national risk driver based on estimated cancer risk and, nationally, has not exhibited significant changes in concentration, likely associated with the large pool of natural isoprene and formaldehyde emissions. Benzene, toluene, ethylbenzene, and 1,3-butadiene are ubiquitous VOC HAPs with large mobile source contributions that continue to exhibit declining concentrations over the last decade. Common chlorinated organic compounds such as ethylene dichloride and methylene chloride exhibit increasing concentrations. The variety of physical and chemical attributes and measurement technologies across 187 HAPs result in a broad range of method detection limits (MDLs) and cancer risk thresholds that challenge confidence in risk results for low concentration HAPs with MDLs near or greater than risk thresholds. From a national monitoring network perspective, the ability of the HAPs observational database to characterize the multiple pollutant and spatial scale patterns influencing exposure is severely limited and positioned to benefit by leveraging a variety of emerging measurement technologies.

Implications:?Ambient air toxics observation networks have limited ability to characterize the broad suite of hazardous air pollutants (HAPs) that affect exposures across multiple spatial scales. While our networks are best suited to capture major urban-scale signals of ubiquitous volatile organic compound HAPs, incorporation of sensing technologies that address regional and local-scale exposures should be pursued to address major gaps in spatial resolution. Caution should be exercised in interpreting HAPs observations based on data proximity to minimum detection limit and risk thresholds.     

Apportionment of ambient primary and secondary fine particulate matter during a 2001 summer intensive study at the CMU Supersite and NETL Pittsburgh site

Gaseous and particulate pollutant concentrations associated with five samples per day collected during a July 2001 summer intensive study at the Pittsburgh Carnegie Mellon University (CMU) Supersite were used to apportion fine particulate matter (PM2.5) into primary and secondary contributions using PMF2. Input to the PMF2 analysis included the concentrations of PM2.5 nonvolatile and semivolatile organic material, elemental carbon (EC), ammonium sulfate, trace element components, gas-phase organic material, and NO(x), NO2, and O3 concentrations. A total of 10 factors were identified. These factors are associated with emissions from various sources and facilities including crustal material, gasoline combustion, diesel combustion, and three nearby sources high in trace metals. In addition, four secondary sources were identified, three of which were associated with secondary products of local emissions and were dominated by organic material and one of which was dominated by secondary ammonium sulfate transported to the CMU site from the west and southwest. The three largest contributors to PM2.5 were secondary transported material (dominated by ammonium sulfate) from the west and southwest (49%), secondary material formed during midday photochemical processes (24%), and gasoline combustion emissions (11%). The other seven sources accounted for the remaining 16% of the PM2.5. Results obtained at the CMU site were comparable to results previously reported at the National Energy Technology Laboratory (NETL), located approximately 18 km south of downtown Pittsburgh. The major contributor at both sites was material transported from the west and southwest. Some difference in nearby sources could be attributed to meteorology as evaluated by HYSPLIT model back-trajectory calculations. These findings are consistent with the majority of the secondary ammonium sulfate in the Pittsburgh area being the result of contributions from distant transport, and thus decoupled from local activity involving organic pollutants in the metropolitan area. In contrast, the major local secondary sources were dominated by organic material.     

Apportionment of ambient primary and secondary pollutants during a 2001 summer study in Pittsburgh using U.S. Environmental Protection Agency UNMIX

Apportionment of primary and secondary pollutants during the summer 2001 Pittsburgh Air Quality Study (PAQS) is reported. Several sites were included in PAQS, with the main site (the supersite) adjacent to the Carnegie Mellon University campus in Schenley Park. One of the additional sampling sites was located at the National Energy Technology Laboratory, located approximately 18 km southeast of downtown Pittsburgh. Fine particulate matter (PM2.5) mass, gas-phase volatile organic material (VOM), particulate semivolatile and nonvolatile organic material (NVOM), and ammonium sulfate were apportioned at the two sites into their primary and secondary contributions using the U.S. Environmental Protection Agency UNMIX 2.3 multivariate receptor modeling and analysis software. A portion of each of these species was identified as originating from gasoline and diesel primary mobile sources. Some of the organic material was formed from local secondary transformation processes, whereas the great majority of the secondary sulfate was associated with regional transformation contributions. The results indicated that the diurnal patterns of secondary gas-phase VOM and particulate semivolatile and NVOM were not correlated with secondary ammonium sulfate contributions but were associated with separate formation pathways. These findings are consistent with the bulk of the secondary ammonium sulfate in the Pittsburgh area being the result of contributions from distant transport and, thus, decoupled from local activity involving organic pollutants in the metropolitan area.     

Trends in Concentrations of Benzene Soluble Suspended Particulate Fraction and Benzo(a)pyrene

The bacterial mutagenicity of ambient particulate organic matter (POM) was measured for consecutive 3-hour time intervals over a 27-hour period in March 1983 at two sites on opposite sides of the heavily traveled San Diego Freeway (I-405) in West Los Angeles (WLA), California, the diurnal variations in the direct (not requiring S9 metabolic activation) mutagenic burden of airborne particulates and the magnitude of the mutagen doses observed at these sites were similar to those previously observed at a site just east of downtown Los Angeles (ELA). Highs (～150 rev m^?3) and lows (～35 rev m^?3) in mutagen densities occurred over short time intervals (a few hours) probably due to changes in emissions, mixing heights and wind speeds. Offshore air flows which drained the air basin between midnight and 0600 PST resulted in elevated mutagen density levels at the western edge of the Los Angeles Basjn. The incremental burden of direct mutagens in respirable POM attributable to freeway traffic reached 50 rev m^?3 during this study. Consistent with our results for ELA there was diminished response on the Salmonella typhimurium nitroreductase-deficient strain TA98NR vs. TA98 suggesting that nitroarenes contribute significantly to the direct mutagenicity of POM collected at the WLA sites.     

Sources of variability in ambient air toxics monitoring data

Under the Clean Air Act Amendments, the United States Environmental Protection Agency is required to regulate emissions of 188 hazardous air pollutants. The EPA, Office of Air Quality Planning and Standards is currently conducting a National-scale Air Toxics Assessment with a goal to identify air toxics which are of greatest concern, in terms of contribution to population inhalation risk. The results will be used to set priorities for the collection of additional air toxics emissions and monitoring data. Expanded ambient air toxics monitoring will take the form of a national air toxics monitoring network. With all monitoring data, however, comes uncertainty in the form of environmental variability (spatial and temporal) and monitoring error (sample collection and laboratory analysis). With this in mind, existing data from the Urban Air Toxics Monitoring Program (UATMP) were analyzed to obtain a general understanding of these sources of variability and then provide recommendations for managing the data uncertainties of a national network. The results indicate that environmental variability, in particular temporal, comprises most of the overall variability observed in the UATMP data. However, at lower ambient levels (on the order of 0.1–0.5 ppbv or lower) environmental variability tends to dissipate and monitoring error takes over, most notably analytical error. Overall, the results suggest that common techniques in ambient air toxics monitoring for carbonyls and volatile organic compounds may satisfy many of the primary objectives of a national air toxics monitoring network.     

Luncheon Address

ABSTRACT

The U.S. Department of Energy (DOE), through the Federal Energy Technology Center (FETC), manages the largest funded program in the country for developing (1) an understanding of mercury emissions, (2) measurement of these emissions, and (3) control technology (-ies) for these emissions for the U.S. coal-fired electric generating industry. DOE has initiated, or has collaborated with other government and industrial organizations in, these and other efforts relating to mercury and other hazardous air pollutants (HAPs), also known as air toxics. One of DOE's first reports on trace elements in coal was conducted from 1976 through 1978 by researchers at DOE's Pittsburgh Energy Technology Center (PETC, now FETC) and the Pittsburgh Mining Operations of the Department of the Interior's Bureau of Mines. The report was completed less than two years after DOE was formed, and 13 years before Title III of the 1990 Clean Air Act Amendments was enacted (Cavallaro et al., March 1978).     

A method of assessing air toxics concentrations in urban areas using mobile platform measurements

The objective of this paper is to demonstrate an approach to characterize the spatial variability in ambient air concentrations using mobile platform measurements. This approach may be useful for air toxics assessments in Environmental Justice applications, epidemiological studies, and environmental health risk assessments. In this study, we developed and applied a method to characterize air toxics concentrations in urban areas using results of the recently conducted field study in Wilmington, DE. Mobile measurements were collected over a 4- x 4-km area of downtown Wilmington for three components: formaldehyde (representative of volatile organic compounds and also photochemically reactive pollutants), aerosol size distribution (representing fine particulate matter), and water-soluble hexavalent chromium (representative of toxic metals). These measurements were,used to construct spatial and temporal distributions of air toxics in the area that show a very strong temporal variability, both diurnally and seasonally. An analysis of spatial variability indicates that all pollutants varied significantly by location, which suggests potential impact of local sources. From the comparison with measurements at the central monitoring site, we conclude that formaldehyde and fine particulates show a positive correlation with temperature, which could also be the reason that photochemically generated formaldehyde and fine particulates over the study area correlate well with the fine particulate matter measured at the central site.     

Evaluation of Risks from Urban Air Pollutants in the Southeast Chicago Area

Region V of the U.S. Environmental Protection Agency has conducted a comprehensive study of cancer risks from urban exposure to air pollutants in the Southeast Chicago area. This study estimated emissions of a list of 30 air carcinogens from a broad range of nontraditional, as well as traditional, source types. Using dispersion modeling and applying the appropriate unit risk factors and population data, this study estimated the risks at each receptor location and the total number of cancer cases attributable to air pollution in the area.

This analysis estimated that current concentrations would cause 77 cases of cancer over the next 70 years, an average risk of 2.0 × 10^?4. Contributions from different source types and different pollutants were estimated. The total contribution from nontraditional source types was less than 0.3 percent. Although these estimates are highly uncertain, the study does suggest the nature and general magnitude of cancer risks from air pollution in the urban area studied.     

Characteristics and diurnal variations of NMHCs at urban,suburban, and rural sites in the Pearl River Delta and a remote site in South China

The Pearl River Delta (PRD) is one of the most industrialized and urbanized regions in China. With rapid growth of the economy, it is suffering from deteriorating air quality. Non-methane hydrocarbons (NMHCs) were investigated at urban and suburban sites in Guangzhou (GZ), a rural site in PRD and a clean remote site in South China, in April 2005. Additional roadside samples in GZ and Qingxi (QX, a small industrial town in PRD), ambient air samples at the rooftop of a printing factory in QX and exhaust samples from liquefied petroleum gas (LPG)—fueled taxis in GZ were collected to help identify the source signatures of NMHCs. A large fraction of propane (47%) was found in exhaust samples from LPG-fueled taxis in GZ and extremely high levels of toluene (2.0–3.1 ppmv) were found at the rooftop of the printing factory in QX. Vehicular and industrial emissions were the main sources of NMHCs. The effect of vehicular emission on the ambient air varied among the three PRD sites. The impact of industrial emissions was widespread and they contributed greatly to the high levels of aromatic hydrocarbons, especially toluene, at the three PRD sites investigated. Leakage from vehicles fueled by LPG contributed mainly to the high levels of propane and n-butane at the urban GZ site. Ethane and ethyne from long-range transport and isoprene from local biogenic emission were the main contributors to the total hydrocarbons at the remote site. Diurnal variations of NMHCs showed that the contribution from vehicular emissions varied with traffic conditions and were more influenced by fresh emissions at the urban site and by aged air at the suburban and rural sites. Isoprene from biogenic emission contributed largely to the ozone formation potential (OFP) at the remote site. Ethene, toluene and m/p-xylene were the main contributors to the OFP at the three PRD sites.     

Residential Indoor,Outdoor, and Workplace Concentrations of Carbonyl Compounds: Relationships with Personal Exposure Concentrations and Correlation with Sources

Abstract

Personal 48-hr exposures of 15 randomly selected participants as well as microenvironment concentrations in each participant’s residence and workplace were measured for 16 carbonyl compounds during summer–fall 1997 as a part of the Air Pollution Exposure Distributions within Adult Urban Populations in Europe (EXPOLIS) study in Helsinki, Finland. When formaldehyde and acetaldehyde were excluded, geometric mean ambient air concentrations outside each participant’s residence were less than 1 ppb for all target compounds. Geometric mean residential indoor concentrations of carbonyls were systematically higher than geometric mean personal exposures and indoor workplace concentrations. Additionally, residential indoor/outdoor ratios indicated substantial indoor sources for most target compounds. Carbonyls in residential indoor air correlated significantly, suggesting similar mechanisms of entry into indoor environments. Overall, this study demonstrated the important role of non-traffic-related emissions in the personal exposures of participants in Helsinki and that comprehensive apportionment of population risk to air toxics should include exposure concentrations derived from product emissions and chemical formation in indoor air.     

Characterization of Carbonaceous Species of Ambient PM2.5 in Beijing,China

Abstract

One-week integrated fine particulate matter (i.e., particles <2.5 μm in diameter; PM_2.5) samples were collected continuously with a low-flow rate sampler at a downtown site (Chegongzhuang) and a residential site (Tsinghua University) in Beijing between July 1999 and June 2000. The annual average concentrations of organic carbon (OC) and elemental carbon (EC) at the urban site were 23.9 and 8.8 μg m^?3, much higher than those in some cities with serious air pollution. Similar weekly variations of OC and EC concentrations were found for the two sampling sites with higher concentrations in the winter and autumn. The highest weekly variations of OC and EC occurred in the winter, suggesting that combustion sources for space heating were important contributors to carbonaceous particles, along with a significant impact from variable meteorological conditions. High emissions coupled with unfavorable meteorological conditions led to the max weekly carbonaceous concentration the week of November 18–25, 1999. The weekly mass ratios of OC:EC ranged between 2 and 4 for most samples and averaged 2.9, probably suggesting that secondary OC (SOC) is present most weeks. The range of contemporary carbon fraction, based on the C14 analyses of eight samples collected in 2001, is 0.330–0.479. Estimated SOC accounted for ～38% of the total OC at the two sites. Average OC and EC concentrations at Tsinghua University were 25% and 18%, respectively, higher than those at Chegongzhuang, which could be attributed to different local emissions of primary carbonaceous particles and gaseous precursors of SOC, as well as different summer photochemical intensities between the two locations.     

Emission Factors of Air Toxics from Semiconductor Manufacturing in Korea

Abstract

The development of local, accurate emission factors is very important for the estimation of reliable national emissions and air quality management. For that, this study is performed for pollutants released to the atmosphere with source-specific emission tests from the semiconductor manufacturing industry. The semiconductor manufacturing industry is one of the major sources of air toxics or hazardous air pollutants (HAPs); thus, understanding the emission characteristics of the emission source is a very important factor in the development of a control strategy. However, in Korea, there is a general lack of information available on air emissions from the semiconductor industry. The major emission sources of air toxics examined from the semiconductor manufacturing industry were wet chemical stations, coating applications, gaseous operations, photolithography, and miscellaneous devices in the wafer fabrication and semiconductor packaging processes. In this study, analyses of emission characteristics, and the estimations of emission data and factors for air toxics, such as acids, bases, heavy metals, and volatile organic compounds from the semiconductor manufacturing process have been performed. The concentration of hydrogen chloride from the packaging process was the highest among all of the processes. In addition, the emission factor of total volatile organic compounds (TVOCs) for the packaging process was higher than that of the wafer fabrication process. Emission factors estimated in this study were compared with those of Taiwan for evaluation, and they were found to be of similar level in the case of TVOCs and fluorine compounds.     

Assessment of indoor air concentrations of VOCs and their associated health risks in the library of Jawaharlal Nehru University,New Delhi

The present work investigated the levels of total volatile organic compounds (TVOC) and benzene, toluene, ethylbenzene, m/p-xylene, and o-xylene (BTEX) in different microenvironments in the library of Jawaharlal Nehru University in summer and winter during 2011–2012. Carcinogenic and non-carcinogenic health risks due to organic compounds were also evaluated using US Environmental Protection Agency (USEPA) conventional approaches. Real-time monitoring was done for TVOC using a data-logging photo-ionization detector. For BTEX measurements, the National Institute for Occupational Safety and Health (NIOSH) standard method which consists of active sampling of air through activated charcoal, followed by analysis with gas chromatography, was performed. Simultaneously, outdoor measurements for TVOC and BTEX were carried out. Indoor concentrations of TVOC and BTEX (except benzene) were higher as compared to the outdoor for both seasons. Toluene and m/p-xylene were the most abundant organic contaminant observed in this study. Indoor to outdoor (I/O) ratios of BTEX compounds were generally greater than unity and ranged from 0.2 to 8.7 and 0.2 to 4.3 in winter and summer, respectively. Statistical analysis and I/O ratios showed that the dominant pollution sources mainly came from indoors. The observed mean concentrations of TVOC lie within the second group of the Molhave criteria of indoor air quality, indicating a multifactorial exposure range. The estimated lifetime cancer risk (LCR) due to benzene in this study exceeded the value of 1?×?10^?6 recommended by USEPA, and the hazard quotient (HQ) of non-cancer risk came under an acceptable range.     

Quantitative cancer risk assessment and local mortality burden for ambient air pollution in an eastern Mediterranean City

Health risks posed by ambient air pollutants to the urban Lebanese population have not been well characterized. The aim of this study is to assess cancer risk and mortality burden of non-methane hydrocarbons (NMHCs) and particulates (PM) based on two field-sampling campaigns conducted during summer and winter seasons in Beirut. Seventy NMHCs were analyzed by TD-GC-FID. PM_2.5 elemental carbon (EC) components were examined using a Lab OC-EC aerosol Analyzer, and polycyclic aromatic hydrocarbons were analyzed by GC-MS. The US EPA fraction-based approach was used to assess non-cancer hazard and cancer risk for the hydrocarbon mixture, and the UK Committee on Medical Effects of Air Pollutants (COMEAP) guidelines were followed to determine the PM_2.5 attributable mortality burden. The average cumulative cancer risk exceeded the US EPA acceptable level (10⁻⁶) by 40-fold in the summer and 30-fold in the winter. Benzene was found to be the highest contributor to cancer risk (39–43%), followed by 1,3-butadiene (25–29%), both originating from traffic gasoline evaporation and combustion. The EC attributable average mortality fraction was 7.8–10%, while the average attributable number of deaths (AD) and years of life lost (YLL) were found to be 257–327 and 3086–3923, respectively. Our findings provide a baseline for future air monitoring programs, and for interventions aiming at reducing cancer risk in this population.