聚合物驱采出污水有效回注方法探讨

通过室内实验研究金属铁锈对聚合物黏度的影响、污水中二价铁离子对聚合物黏度的影响、污水中三价铁离子对聚合物黏度的影响,通过在采出污水中加入污水处理剂、曝氧、加入一定比例清水的方式,能够提高采出污水配置或者稀释聚合物溶液的黏度。进行聚合物溶液的合理配置,实现采出污水有效回注,是降低环境污染的有效方法。     

聚合物驱注入液黏度稳定剂研究进展

油田采出水中影响聚合物溶液黏度的主要因素有金属离子、还原性物质、细菌等,次要影响因素有pH值、溶解氧、含油量、悬浮固体、残余聚合物、残余化学剂等。针对以上影响因素,可通过投加适宜的化学剂来消除影响,从而控制聚合物溶液的黏度损失。根据作用机理,目前常用的黏度稳定剂可分为水质改性型和黏度稳定型两种,对造成黏度损失的主要因素可投加水质改性型药剂、对溶解氧等问题可投加黏度稳定型药剂来降低黏度损失。此外,不同单剂组合的复配可通过协同作用有效地提高药剂效果,复合型药剂的应用前景将更为广阔。     

含硫低浊度采油污水絮凝处理技术的研究

中原油田明二污属含硫低浊度污水,处理后水主要用于回注。文章通过pH调节剂的优选、除硫剂优选并与絮凝药剂联合,对明二污含硫低浊度污水进行了絮凝处理。结果表明:当pH值为7.5、2#絮凝剂加量为50mg/L、有机絮凝剂加量为0.5mg/L、除硫剂加量为20mg/L时,处理后水中的悬浮物、总铁和含油量分别达到1.9mg/L、0.43mg/L和0mg/L;SRB、TGB均为102个/mL;腐蚀速率及结垢量分别降到0.062mm/a和1.9mg/L;污泥产生量降低到0.23～0.26mg/L;在90℃时的结垢量由地层水的23.3mg/L降低到1.9mg/L,处理后的水达到中原油田回注水的水质标准,并且水质稳定。     

聚合物溶液黏度影响因素分析及控制对策

文章分析了聚合物溶液性质、配制水源水质和机械剪切对聚合物溶液黏度的影响。分别用辽河油田欢三联软化清水和软化污水配制聚合物母液,用水驱污水和二元驱污水配制目的液,并测定目的液黏度;在相同搅拌时间下,测定不同转速对母液黏度的影响。结果表明：“软化清水＋水驱污水”配制的目的液 黏度最大,“软化污水＋二元驱污水”配制的目的液黏度最小,且在目的液中增加表面活性剂,对目的液黏度基本无影响;搅拌时间相同时,转速越小母液黏度越大。提出控制聚合物黏度的主要方法,一是筛选出适合油藏特性的聚合物类型,并通过改变聚合物分子结构增强其抗剪切和抗盐性能;二是选择合理的化学驱污水 处理工艺,降低不利因素对配制液黏度的影响;三是优化从配制、注入到运行操作的全过程工艺方案,保证聚 合物的充分熟化及聚合物溶液的流态稳定、改变双螺带搅拌器的运行方式和内部结构可以提高母液的熟化效率。     

电化学在三元复合驱采出水深度处理中的应用

采用电化学法对三元复合驱采出水常规工艺砂滤出水进行脱稳降黏处理,利用电絮凝催化氧化模块,实现高压脉冲电絮凝—微波紫外超声反应区—电催化氧化的联合作用,将悬浮固体降至5mg/L以下,聚合物降至50mg/L以下,含油量、COD及黏度均有大幅降低,为后续超滤膜、电渗析等深度处理工艺提供有利的进水条件,为配聚、外排提供技术支持。     

吉林油田稠油热采污水处理絮凝剂实验研究＊

在含油污水水质分析的基础上,采用烧杯实验和分光光度法研究絮凝剂的絮凝效果。筛选出以无机絮凝剂硫酸铝与两性高分子聚合物CE-3090的复配体系,同时研究了影响絮凝效果的因素并探究了其影响机理。结果表明:在温度为40℃,pH为7.72,170 r/min时高速搅拌1 min,然后50 r/min低速搅拌5 min,硫酸铝的加量为90 mg/L、CE-3090的加量为0.5 mg/L,絮凝沉降30 min后其絮凝效果较好。实验证明:该复配处理剂处理含油污水后,含油量和杂质含量都达到了SY/T 5329-94《碎屑岩油藏注水水质推荐指标及分析方法》油田污水回注的要求。     

生化处理沙漠油田高盐含油污水

文章研究了含油污水生化处理装置在某油田13~#站井区的试验情况。采用驯化培养的"某油田13#站高效优势菌种"对石油类物质具有良好的降解性能、盐度适应范围广。利用该菌种对油田外排污水进行二级生化处理,结果表明:处理后污水COD低于100mg/L;石油类浓度低于10mg/L;挥发酚浓度低于0.5mg/L。含油污水生化处理装置可处理含油高于500mg/L,矿化度高于20 000mg/L,进水量高于4.0m~3/h的油田污水。研究表明利用微生物工艺处理高盐、高矿化度油田污水技术可行,工艺可靠,具有推广应用的价值。     

油田污水膜法处理工艺优化及膜污染分析

利用扫描电镜、原子力显微镜、能谱分析等对油田采出水膜污染的机理进行研究,确定了污水中的有机污染物是导致膜污染的主要因素.通过优化预处理,控制膜污染,形成以生物接触氧化为核心的预处理与膜过滤相集成的油田污水资源化处理工艺.现场试验结果表明：预处理后污水COD67.3～92.6mg/L,浊度〈0.5NTU,悬浮物〈1.0mg/L,含油〈1.0mg/L,保障了膜过滤系统的稳定运行.膜过滤产水达到油田锅炉用水和配制聚合物用水标准.     

风城油田超稠油采出水处理工艺及应用

风城油田超稠油采出水具有"含砂高、黏度高、密度高"的特点,大量不易分离的粉砂和泥质附在油中,其乳化稳定性强,处理难度大;沉降脱水罐来水含油量10 000 mg/L,悬浮物500 mg/L,高含油及悬浮物对采出水处理系统影响及冲击较大。采用"两级除油+混凝反应+两级过滤"工艺对超稠油采出水进行处理,处理后净化水含油量≤2 mg/L,悬浮物≤2 mg/L,污水处理合格率100%,污水回用率100%,回用油田注汽锅炉。实现了污水的循环利用,节约清水费用2 463.75万元,可充分利用高温采出水热能,年均节约天然气用量约5 475×10~4 Nm~3,节约天然气费用5 365.5万元。     

含油污水回用处理新工艺研究

研究了一种处理回用含油污水的新工艺,二期炼油污水深度处理中试研究表明,以炼油企业二级处理达标排放污水为处理对象,在使用该工艺处理水量为0.5m3/h、水力停留时间为1.49h 以及污水中COD、氨氮、石油类的浓度变化分别为44.07～102.13 mg/L、28.37～50.01 mg/L、4.10～6.77 mg/L时,平均去除率分别达到94%、96.1%、91.9%,其排出水质符合循环水补充水的水质要求。对该工艺进行了5.5h抗冲击实验,结果表明其抗冲击能力优良。     

Bioproduction of ferric sulfate used during heavy metals removal from sewage sludge

Toxic metals removal from wastewater sewage sludge can be achieved through microbial processes involving Acidithiobacillus ferrooxidans. The oxidation of ferrous ions by A. ferrooxidans, cultured in sewage sludge filtrate, was studied in both batch and continuous flow stirred tank reactors. Sewage sludge filtrate containing natural nutrients (phosphorus and nitrogen) was recovered as effluent following the dehydration of a primary and secondary sludge mixture. Batch and continuous flow stirred tank reactor tests demonstrated that A. ferrooxidans were able to grow and completely oxidize ferrous iron in a culture medium containing more than 80% (v v(-1)) sewage sludge filtrate with 10 g Fe(II) L(-1) added. Toxic levels were reached when total organic carbon in the sewage sludge filtrate exceeded 250 mg L(-1). The ferric iron solution produced in the sludge filtrate by A. ferrooxidans was used to solubilize heavy metals in primary and secondary sludge. The solubilization of Cu, Cr, and Zn yielded 71, 49, and 80%, respectively. This is comparable with the yield percentages obtained using a FeCl(3) solution. The cost of treating wastewater sewage sludge by bioproducing a ferric ion solution from sewage sludge is three times less expensive than the conventional method requiring a commercial ferric chloride solution.     

Soil property control of biogeochemical processes beneath two subtropical stormwater infiltration basins

Substantially different biogeochemical processes affecting nitrogen fate and transport were observed beneath two stormwater infiltration basins in north-central Florida. Differences are related to soil textural properties that deeply link hydroclimatic conditions with soil moisture variations in a humid, subtropical climate. During 2008, shallow groundwater beneath the basin with predominantly clayey soils (median, 41% silt+clay) exhibited decreases in dissolved oxygen from 3.8 to 0.1 mg L and decreases in nitrate nitrogen (NO-N) from 2.7 mg L to <0.016 mg L, followed by manganese and iron reduction, sulfate reduction, and methanogenesis. In contrast, beneath the basin with predominantly sandy soils (median, 2% silt+clay), aerobic conditions persisted from 2007 through 2009 (dissolved oxygen, 5.0-7.8 mg L), resulting in NO-N of 1.3 to 3.3 mg L in shallow groundwater. Enrichment of δN and δO of NO combined with water chemistry data indicates denitrification beneath the clayey basin and relatively conservative NO transport beneath the sandy basin. Soil-extractable NO-N was significantly lower and the copper-containing nitrite reductase gene density was significantly higher beneath the clayey basin. Differences in moisture retention capacity between fine- and coarse-textured soils resulted in median volumetric gas-phase contents of 0.04 beneath the clayey basin and 0.19 beneath the sandy basin, inhibiting surface/subsurface oxygen exchange beneath the clayey basin. Results can inform development of soil amendments to maintain elevated moisture content in shallow soils of stormwater infiltration basins, which can be incorporated in improved best management practices to mitigate NO impacts.     

Nutrient conversions by photosynthetic bacteria in a concentrated animal feeding operation lagoon system

A diurnal examination was conducted to determine the effect of photosynthetic bacteria on nutrient conversions in a two-stage concentrated animal feeding operation (CAFO) lagoon system in west-central Oklahoma. Changes in nutrients, microbial populations, and physical parameters were examined at three depths (0, 1.5, and 3.0 m) every 3 h over a 36-h period. The south lagoon (SL) was anaerobic (dissolved oxygen [DO] = 0.09 +/- 0.12 mg/L) while the north lagoon (NL) was facultative (DO ranged from 4.0-0.1 mg/L over 36-h period). Negative sulfide-sulfate (-0.85) and bacteriochlorophyll a (bchl a)-sulfate (-0.83) correlations, as well as positive bchl a-sulfide (0.87) and light intensity (I)-bchl a (0.89) correlations revealed that the SL was dominated by sulfur conversions driven by the photosynthetic purple sulfur bacteria (PSB). The correlation data was supported by diurnal trends for sulfate, sulfide, and bchl a. Both nitrogen and sulfur conversions played a role in the NL; however, nitrogen conversions appeared to dominate this system because of the activity of cyanobacteria. This was shown by positive chlorophyll a (chl a)-I (0.91) and chl a-nitrate (0.98) correlations and the negative correlation between ammonium and nitrite (-0.88). Correlation data was further supported by diurnal trends observed for chl a, DO, and ammonium. For both lagoons, the dominant photosynthetic microbial species determined which nutrient conversion processes were most important.     

Physico-chemical characteristics of well waters in four urban centers in Southern Nigeria

An ensemble of thirty physico-chemical characteristics was used to assess the quality of well waters in four urban centers in southern Nigeria: Lagos, Benin City, Warri, and Ekpoma. The characteristics investigated include pH; color; turbidity; salinity; electrical conductivity, EC; total dissolved solids, TDS; total suspended solids, TSS; dissolved oxygen, DO; total hydrocarbon, THC; biochemical oxygen demand, BOD; chemical oxygen demand, COD; and nitrate, nitrite, ammonia, sulfate, and phosphate concentrations. Also monitored were the concentrations of sodium, calcium, potassium, magnesium, chloride, bicarbonate, iron, lead, copper, manganese, zinc, chromium, nickel, and cadmium. The results obtained were compared with World Health Organization, WHO, and Nigerian Federal Ministry of Environment, FME, drinking water standards. The results show that with the well water obtained from Lagos, turbidity, 11.80 NTU; pH, 5.68; EC, 1065.55 μS/cm; TDS, 539.00 mg/L; concentrations of iron, 1.83 mg/L; manganese, 0.14 mg/L; and lead, 1.35 mg/L did not meet the WHO standards. In Warri, pH, 5.19; concentrations of lead, 1.35 mg/L; and chromium, 0.10 mg/L in the well water were above the WHO desirable limits. The results also indicated that the well water from Benin City contained concentrations of chromium, 0.18 mg/L; and lead, 0.20 mg/L that exceeded the recommended WHO limits. In Ekpoma, the pH, 6.00; concentrations of chromium, 0.15 mg/L; and lead, 0.44 mg/L were higher than the desirable limits of WHO. Generally, the assessments revealed that the waters were good and fit for drinking and other domestic application without serious threat to public health.     

Bayesian approach to estimating margin of safety for total maximum daily load development

A Bayesian-updating approach is presented to the estimation of total uncertainty-based Margin of Safety (MOS) for Total Maximum Daily Load (TMDL) calculations. Probability distributions are presented to construct the likelihood function, the prior probability distribution, and the posterior (total uncertainty) probability distribution. The Bayesian-updating approach is demonstrated through a case study for the Lower Amite River, Louisiana. The posterior probability distribution-based on the Bayesian approach updates the standard deviation of summer dissolved oxygen in the Amite River from 1.88 mg/L to 2.10 mg/L when the total uncertainty is considered. Results from the Bayesian-updating approach are compared with two conventional methods. The dissolved oxygen reserve based on a conventional margin of safety of 20% is estimated to be 45,682.26 kg/Day. The second conventional method, where we consider the standard deviation of 1.88 mg/L, produces a dissolved oxygen reserve of 40,516.09 kg/Day. The Bayesian approach yields the dissolved oxygen reserve of 38,614.43 kg/Day with the first level (μ-σ) of MOS, producing a deficit of 5606.65 kg/Day in dissolved oxygen. The dissolved oxygen reserve deficit increases to 23,895.13 kg/Day when the second level (μ-2σ) of MOS is used, which escalated to 42,383.52 kg/Day when the highest level (μ-3σ) of MOS is used. While the total uncertainty-based Bayesian approach is demonstrated for a TMDL development on the Amite River, the overall approach could be applied in any river system with similar available data.     

低温捕集/热解吸气相色谱法分析废气中挥发性硫化物

采用低温捕集/热解吸/火焰光度检测填充柱气相色谱法可分析废气中挥发性硫化物。标准气浓度为2.80g/L～38.10g/L时,硫化氢、甲硫醇、乙硫醇、甲硫醚和二甲二硫的平均回收率及相对标准偏差分别为92.1%～106.8%及0.5%～6.0%,采样体积为1.0L时,上述挥发性硫化物的最低检出浓度为0.08ng/L～0.65ng/L。该分析测定了炼油厂某些污染源和催化燃烧脱硫中试装置废气中挥发性硫化物组成,验证了方法的适用性。     

多项膜生物反应器在含盐废水处理中的应用

文章介绍了哈尔滨石化公司应用多项膜生物反应器处理炼化企业含盐废水。影响膜生物反应器的主要运行参数有电导率、溶解氧、COD,电导率适宜范围是3000～5000μS/cm,大于6000μS/cm微生物受到抑制,低于2000μS/cm时,去除率显著下降;一级好氧单元溶解氧适宜范围4.2～7.0mg/L或2.0～3.0mg/L,分别是好氧微生物和兼性微生物占据优势;当进水COD低于500mg/L,出水可稳定达到GB8978-1996《污水综合排放标准》二级标准(COD≤120mg/L)。     

掺杂型二氧化钛纳米管光催化降解甲基橙研究

利用本实验室制备的N-F原子掺杂二氧化钛纳米管作催化剂,在可见光区对甲基橙(MO)进行光催化降解实验。在催化剂用量固定为3cm2时考察了不同初始浓度、pH值、溶解氧(DO)等对降解率的影响。结果表明,在可见光区该催化剂具有较高的光催化活性;当溶液DO为19.2mg/L、pH值为3、初始浓度为10mg/L、反应时间300min时,降解率可达82.3%。     

水样中亚铁及总铁含量连续测定方法探讨

文章研究了在同一样品溶液中连续测定亚铁和总铁的分析方法,对同一标准样品溶液和实际样品进行了单独测定亚铁和总铁含量的实验,同时在完成亚铁含量测定后加入试剂,进行了总铁含量的连续测定,并对实验数据进行相对误差分析。结果表明:单独和连续测定的总铁含量数据无显著性差异,方法切实可行。