Optimization of thermophilic anaerobic-aerobic treatment system for Palm Oil Mill Effluent (POME)

Optimization of an integrated anaerobic-aerobic bioreactor (IAAB) treatment system for the reduction of organic matter (Chemical Oxygen Demand (COD), Biochemical Oxygen Demand (BOD) and Total Suspended Solids (TSS) concentrations) in Palm Oil Mill Effluent (POME) to legal standards with high methane yield was performed for the first time under thermophilic condition (50°C–55°C) by using response surface methodology (RSM). The experiments were conducted based on a central composite rotatable design (CCRD) with three independent operating variables, organic loading rates in anaerobic compartment (OLR_an) and mixed liquor volatile suspended solids (MLVSS) concentration in anaerobic (MLVSS_an) and aerobic compartments (MLVSS_a). The optimum conditions for the POME treatment were determined as OLR_an of 15.6 g COD·L^-1·d^-1, MLVSS_an of 43100 mg·L^-1, and MLVSS_a of 18600 mg·L^-1, where high aerobic COD, BOD and TSS removal efficiencies of 96.3%, 97.9%, and 98.5% were achieved with treated BOD of 56 mg·L^-1 and TSS of 28 mg·L^-1 meeting the discharge standard. This optimization study successfully achieved a reduction of 42% in the BOD concentrations of the final treated effluent at a 48% higher OLR_an as compared to the previous works. Besides, thermophilic IAAB system scores better feasibility and higher effectiveness as compared to the optimized mesophilic system. This is due to its higher ability to handle high OLR with higher overall treatment efficiencies (more than 99.6%), methane yield (0.31 L CH₄·g^-1 COD_removed) and purity of methane (67.5%). Hence, these advantages ascertain the applicability of thermophilic IAAB in the POME treatment or even in other high-strength wastewaters treatment.     

Enhanced dewatering characteristics of waste activated sludge with Fenton pretreatment: effectiveness and statistical optimization

In this work, the enhanced dewaterabing characteristics of waste activated sludge using Fenton pretreatment was investigated in terms of effectiveness and statistical optimization. Response surface method （RSM） and central composite design （CCD） were applied to evaluate and optimize the effectiveness of important operational parameters, i.e., H202 concentrations, Fe2＋ concentrations and initial pH values. A significant quadratic polynomial model was obtained （R2= 0.9189） with capillary suction time （CST） reduction efficiency as the response. Numerical optimization based on desirability function was carried out. The optimum values for H202, Fe2, and initial pH were found to be 178 mg-g-1 VSS （volatile suspended solids）, 211mg.gI VSS and 3.8, respectively, at which CST reduction efficiency of 98.25% could be achieved. This complied well with those predicted by the established polynomial model. The results indicate that Fenton pretreatment is an effective technique for advanced waste activated sludge dewatering. The enhancement of sludge dewaterability by Fenton＇s reagent lies in the migration of sludge bound water due to the disintegration of sludge flocs and microbial cells lysis.     

Performance of an ANAMMOX reactor treating wastewater generated by antibiotic and starch production processes

A pilot-scale anaerobic ammonia oxidation (ANAMMOX) reactor was used to treat mixed wastewater resulting from a chlortetracycline and starch production process. The results, collected over the course of 272 days, show that the ratio of influent ammonium to nitrite, pH, and temperature can all affect the efficiency of nitrogen removal. The ratio of influent ammonium to nitrite was maintained at about 1:1 at a concentration below 200 mg·L^-1 for both influent ammonium and nitrite. The total nitrogen (TN) loading rate was 0.15–0.30 kgN·m^-3·d^-1, pH remained at 7.8–8.5, and temperature was recorded at 33±1°C. The rate of removal of ammonia, nitrite, and TN were over 90%, 90%, and 80%, and the effluent ammonium, nitrite and TN concentrations were below 50, 30, and 100 mg·L^-1.     

Migration of manganese and iron during the adsorption-regeneration cycles for arsenic removal

Fe-Mn binary oxide incorporated into porous diatomite (FMBO-diatomite) was prepared in situ and regenerated in a fixed-bed column for arsenite [As(III)] and arsenate [As(V)] removal. Four consecutive adsorption cycles were operated under the following conditions: Initial arsenic concentration of 0.1 mg·L^-1, empty bed contact time of 5 min, and pH 7.0. About 3000, 3300, 3800, and 4500 bed volumes of eligible effluent (arsenic concentration≤0.01 mg·L^-1) were obtained in four As(III) adsorption cycles; while about 2000, 2300, 2500, and 3100 bed volumes of eligible effluent were obtained in four As(V) adsorption cycles. The dissection results of FMBO-diatomite fixed-bed exhibited that small amounts of manganese and iron were transferred from the top of the fixed-bed to the bottom of the fixed-bed during As(III) removal process. Compared to the extremely low concentration of iron (<0.01 mg·L^-1), the fluctuation concentration of Mn²⁺ in effluent of the As(III) removal column was in a range of 0.01–0.08 mg·L^-1. The release of manganese suggested that manganese oxides played an important role in As(III) oxidation. Determined with the US EPA toxicity characteristic leaching procedure (TCLP), the leaching risk of As(III) on exhausted FMBO-diatomite was lower than that of As(V).     

氨基化氧化石墨烯(AGO)的制备及其对六价铬的吸附机制

以乙二胺盐酸盐(EDH)为改性剂改性氧化石墨烯(GO),水热法制备氨基化氧化石墨烯(Amino-functionalized;graphene;oxide,AGO).SEM、XRD、FTIR和Zeta电位表征分析发现,AGO表面含有羟基、羧基及氨基基团,Zeta电位为pH=10.14.以水中低浓度六价铬Cr(Ⅵ)为污染物,探讨了乙二胺盐酸盐(EDH)用量、pH、AGO用量、Cr(Ⅵ)初始浓度以及常见干扰离子对AGO吸附Cr(Ⅵ)影响.结果表明,在pH=6.0、7-AGO用量为0.8;mg·L^-1和Cr(Ⅵ)初始浓度为2.0;mg·L^-1,7-AGO对Cr(Ⅵ)去除率可达95.1%;SO₄^2-会明显抑制AGO对Cr(Ⅵ)的吸附.AGO对Cr(Ⅵ)的吸附过程符合二级动力学模型,吸附机制主要为静电作用.     

Influence of aeration intensity on the performance of A/O-type sequencing batch MBR system treating azo dye wastewater

Among the numerous parameters affecting the membrane bioreactor (MBR) performance, the aeration intensity is one of the most important factors. In the present investigation, an anoxic/aerobic-type (A/O-type) sequencing batch MBR system, added anoxic process as a pretreatment to improve the biodegradability of azo dye wastewater, was investigated under different aeration intensities and the impact of the aeration intensity on effluent quantity, sludge properties, extracellular polymeric substances (EPS) amount generated as well as the change of permeation flux were examined. Neither lower nor higher aeration intensities could improve A/O-type sequencing batch MBR performances. The results showed 0.15 m³·h^-1 aeration intensity was promising for treatment of azo dye wastewater under the conditions examined. Under this aeration intensity, chemical oxygen demand (COD), ammonium nitrogen and color removal as well as membrane flux amounted to 97.8%, 96.5%, 98.7% and 6.21 L·m^-2·h^-1, respectively. The effluent quality, with 25.0 mg·L^-1COD, 0.84 mg·L^-1 ammonium nitrogen and 8 chroma, could directly meet the reuse standard in China. In the meantime, the sludge relative hydrophobicity, the bound EPS, soluble EPS and EPS amounts contained in the membrane fouling layer were 70.3%, 52.0 mg·g^-1VSS, 38.8 mg·g^-1VSS and 90.8 mg·g^-1VSS, respectively, which showed close relationships to both pollutant removals and membrane flux.     

Removal of fluoride from water using titanium-based adsorbents

Three adsorbents including TiO₂, Ti-Ce, and Ti-La hybrid oxides were prepared to remove fluoride from aqueous solution. The Ti-Ce and Ti-La hybrid adsorbents obtained by the hydrolysis-precipitation method had much higher sorption capacity for fluoride than the TiO₂ adsorbent prepared through hydrolysis. Rare earth (Ce and La) oxides and TiO₂ exhibited a synergistic effect in the hybrid adsorbents for fluoride sorption. The sorption equilibrium of fluoride on the three adsorbents was achieved within 4 h, and the pseudo-second-order model described the sorption kinetics well. The sorption isotherms fitted the Langmuir model well, and the adsorption capacities of fluoride on the Ti-Ce and Ti-La adsorbents were about 9.6 and 15.1 mg·g^-1, respectively, at the equilibrium fluoride concentration of 1.0 mg·L^-1, much higher than the 1.7 mg·g^-1 on the TiO₂. The sorption capacities of fluoride on the three adsorbents decreased significantly when the solution pH increased from 3 to 9.5. The electrostatic interaction played an important role in fluoride removal by the three adsorbents, and Fourier transform infrared (FTIR) analysis indicated that the hydroxyl groups on the adsorbent surface were involved in fluoride adsorption.     

低碳氮比废水好氧颗粒污泥系统稳定性及微生物种群多样性研究

低碳氮比(C/N)废水处理是含氮废水处理中的难题之一.本实验在C/N为4:1和2:1(COD和NH₄⁺-N浓度分别为400 mg·L^-1和100 mg·L^-1,400 mg·L^-1和200 mg·L^-1)条件下,考察好氧颗粒污泥系统对低碳氮比废水的处理效果、长期运行稳定性,研究C/N对好氧颗粒微生物结构变化的影响.研究结果表明,在C/N为4:1的废水中接种活性污泥培养好氧颗粒污泥,形成的颗粒沉降性能良好,MLSS为4.94 g·L^-1,SVI30为40 mL·g^-1,COD去除率90%以上,氨氮去除率接近100%.降低碳氮比,即C/N为2:1后,好氧颗粒的物理及硝化性能无明显变化,MLSS为11.38 g·L^-1,SVI₃₀/SVI₅维持在1左右,COD去除率大于85%,氨氮去除率98%.碳氮比降低使颗粒微生物多样性减少,其中陶厄氏菌受影响较小,而硝化功能菌出现更替:噬氢菌、食酸菌、里德拜特氏菌消失,鞘氨醇单胞菌、束缚杆菌等成为优势菌种.实验表明,该低碳氮比条件下好氧颗粒污泥系统能够稳定运行,且具有优良的处理性能.     

硝酸钙投加频次对污泥生物调理效果的影响

在接种了反硝化菌的剩余污泥中投加硝酸钙药剂,利用反硝化菌消耗NO₃^-进行反硝化作用去除污泥中易生物降解的有机物,利用Ca²⁺的中和、架桥作用,改善污泥的脱水性能.固定NO₃^-总投加浓度为100 mg·g^-1 TS,在6 d的时间内,按1次、2次、3次、6次的投加频次向污泥中投加硝酸钙.结果表明,1次投加对污泥脱水性能的提升最显著,较对照组而言,污泥CST降低了65.0%,SRF降低了73.2%,污泥脱水性能明显改善;投加硝酸钙后,污泥胞外聚合物中蛋白质含量大幅降低,S层、L层蛋白质分别从13.47 mg·L^-1、11.66 mg·L^-1降低至0.52 mg·L^-1、1.43 mg·L^-1;投加硝酸钙的污泥Zeta电位更趋于电中性.研究还发现,一次性投加硝酸钙产生了更多NO₂^-,有利于污泥结合水,即微生物细胞质的释放.释放出的有机碳被反硝化菌用作碳源,又增强了反硝化效果,从而促进了污泥EPS的破坏与降解,从而改善了污泥的脱水性能.     

Validation of polymer-based nano-iron oxide in further phosphorus removal from bioeffluent: laboratory and scaledup study

The efficient removal of phosphorous from water is an important but challenging task. In this study, we validated the applicability of a new commercially available nanocomposite adsorbent, i.e., a polymer-based hydrated ferric oxide nanocomposite (HFO-201), for the further removal of phosphorous from the bioeffluent discharged from a municipal wastewater treatment plant, and the operating parameters such as the flow rate, temperature and composition of the regenerants were optimized. Laboratory-scale results indicate that phosphorous in real bioeffluent can be effectively removed from 0.92 mg·L^-1 to<0.5 mg·L^-1 (or even<0.1 mg·L^-1 as desired) by the new adsorbent at a flow rate of 50 bed volume (BV) per hour and treatable volume of 3500–4000 BV per run. Phosphorous removal is independent of the ambient temperature in the range of 15°C–40°C. Moreover, the exhausted HFO-201 can be regenerated by a 2% NaOH+ 5% NaCl binary solution for repeated use without significant capacity loss. A scaled-up study further indicated that even though the initial total phosphorus (TP) was as high as 2 mg·L^-1, it could be reduced to<0.5 mg·L^-1, with a working capacity of 4.4–4.8 g·L^-1 HFO-201. In general, HFO-201 adsorption is a choice method for the efficient removal of phosphate from biotreated waste effluent.     

Adsorption property of direct fast black onto acid-thermal modified sepiolite and optimization of adsorption conditions using Box-Behnken response surface methodology

The adsorption of direct fast black onto acid-thermal modified sepiolite was investigated. Batch adsorption experiments were performed to evaluate the influences of experimental parameters such as initial dye concentration, initial solution pH and adsorbent dosage on the adsorption process. The three-factor and three-level Box-Behnken response surface methodology (RSM) was utilized for modeling and optimization of the adsorption conditions for direct fast black onto the acid-thermal modified sepiolite. The raw sepiolite was converted to acid-thermal modified sepiolite, and changes in the fourier transform infrared spectrum (FTIR) adsorption bands of the sample were noted at 3435 cm^-1 and 1427 cm^-1. The zeolitic water disappeared and the purity of sepiolite was improved by acid-thermal modification. The decolorization rate of direct fast black adsorbed increased from 68.2% to 98.9% on acid-thermal modified sepiolite as the initial solution pH decreased from 10 to 2. When the adsorbent dosage reached to 2.5 g·L^-1, 2.0 g·L^-1, 1.5 g·L^-1 and 1.0 g·L^-1, the decolorization rate was 90.3%, 86.7%, 61.0% and 29.8%, respectively. When initial dye concentration increased from 25 to 200 mg·L^-1, the decolorization rate decreased from 91.9% to 60.0%. The RSM results showed that the interaction between adsorbent dosage and pH to be a significant factor. The optimum conditions were as follows: the adsorbent dosage 1.99 g·L^-1, pH 4.22, and reaction time 5.2 h. Under these conditions, the decolorization rate was 95.1%. The three dimensional fluorescence spectra of direct fast black before and after treatment showed that the direct fast black was almost all adsorbed by the acid-thermal modified sepiolite.     

Effects of humic acid on residual Al control in drinking water treatment plants with orthophosphate addition

This study aimed to investigate the effects of humic acid (HA) on residual Al control in drinking water facilities that used orthophosphate addition. The results showed that adding orthophosphate was an effective method for residual Al control for the raw water without HA. When orthophosphate was added at 1.0 min before the addition of poly aluminum chloride (PACl), the concentrations of soluble aluminum (Sol-Al) and total aluminum (Tot-Al) residue were 0.08 and 0.086 mg·L^-1, respectively; both were reduced by 46% compared with the control experiment. The presence of HA would notably increase the residual Al concentration. For the raw water with 5 mg·L^-1 of HA, the concentrations of Sol-Al and Tot-Al increased from 0.136 and 0.174 mg·L^-1 to 0.172 and 0.272 mg·L^-1, respectively. For water with a HA concentration above 5 mg·L^-1, orthophosphate was ineffective in the control of residual Al, though there were still parts of orthophosphate were removed in coagulation. The amounts of Al removal were positively correlated with the solids freshly formed in coagulation. Similar to the raw water without HA, the best Al control was obtained with orthophosphate salt added at 1.0 min before PACl. HA concentrations in the raw water, solution pH, and the orthophosphate dosage suitable for residual Al control by orthophosphate precipitation were also investigated.     

Removal of toxic chromium(VI) from aqueous solution by activated carbon using Casuarina equisetifolia

Highly activated carbon from the seed husk of Casuarina Casuarinas equisetifolia, a worldwide famous plant, have been prepared and tested for the removal of toxic Cr(VI) from its aqueous solution. The adsorbent was investigated for influences of initial chromium concentration (75, 100, 125, and 150 mg l^-1), pH, contact time, and quantity of carbon on removal of Cr(VI) from aqueous solution at room temperature (25±2 °C). The adsorption kinetic of Cr(VI) was studied, and the rates of sorption were found to conform to pseudo-second-order kinetics with a good correlation (R²≥0.99). The Langmuir and Freundlich models fit the isotherm data well. Furthermore, the Gibbs free energy was obtained for each system and was found to be-5.29 kJ mol^-1 for removal of Cr(IV). The negative value of Δ G° indicates the feasibility and spontaneous nature of adsorption. The results indicate that acidic pH (1.05) supported the adsorption of Cr(IV) on activated carbon. The maximum adsorption capacity of Cr(VI) on activated carbon was about 172.4 mg g^-1 at pH 1.05.     

新型溴系阻燃剂环境污染现状研究进展

新型溴系阻燃剂(NBFRs,novel brominated flame retardants)作为传统溴系阻燃剂的替代品已广泛应用于电子产品、纺织品、家具等商品中,随着这些商品的生产、使用和处置,NBFRs不可避免地释放到环境中,给环境和人体带来潜在的危害.部分NBFRs可通过摄食和呼吸作用进入人体对人体产生一定危害...     

高效液相色谱-串联质谱法同时检测水体中26种药物及个人护理品

通过优化固相萃取条件和高效液相色谱-串联质谱参数,建立了可以同时检测地表水和地下水中26种典型药物及个人护理品(pharmaceuticals and personal care products,PPCPs),包括磺胺类、大环内酯类、喹诺酮类、酰胺醇类、精神类、消炎止痛类以及个人护理品的检测方法.通过将水样pH值调节至7,利用HLB固相萃取柱对水样中PPCPs进行富集,以甲醇和含0.005%甲酸的水溶液作为正离子模式流动相,甲醇和含0.5 mmol·L^-1乙酸铵的水溶液作为负离子模式流动相进行梯度洗脱,采用多反应监测的质谱扫描模式(MRM)分析测定.26种PPCPs的检出限为0.007—1.78 ng·L^-1,定量限为0.02—5.68 ng·L^-1,回收率为52.28%—115.24%.利用该方法检测北京潮白河地表水和地下水中PPCPs的浓度,结果表明,地表水中PPCPs的含量普遍高于地下水,磺胺甲恶唑、舒必利、咖啡因、卡马西平和布洛芬在地表水和地下水中的含量相对较高,检测浓度分别高达147.83、52.48、78.35、166.58、30.63 ng·L^-1.     

Fermentative hydrogen production from beet sugar factory wastewater treatment in a continuous stirred tank reactor using anaerobic mixed consortia

A low pH, ethanol-type fermentation process was evaluated for wastewater treatment and bio-hydrogen production from acidic beet sugar factory wastewater in a continuous stirred tank reactor (CSTR) with an effective volume of 9.6 L by anaerobic mixed cultures in this present study. After inoculating with aerobic activated sludge and operating at organic loading rate (OLR) of 12 kgCOD?m^-3·d^-1, HRT of 8h, and temperature of 35°C for 28 days, the CSTR achieved stable ethanol-type fermentation. When OLR was further increased to 18 kgCOD?m^-3·d^-1 on the 53rd day, ethanol-type fermentation dominant microflora was enhanced. The liquid fermentation products, including volatile fatty acids (VFAs) and ethanol, stabilized at 1493 mg·L^-1 in the bioreactor. Effluent pH, oxidation-reduction potential (ORP), and alkalinity ranged at 4.1–4.5, -250–(-290) mV, and 230–260 mgCaCO₃?L^-1. The specific hydrogen production rate of anaerobic activated sludge was 0.1 L?gMLVSS^-1·d^-1 and the COD removal efficiency was 45%. The experimental results showed that the CSTR system had good operation stability and microbial activity, which led to high substrate conversion rate and hydrogen production ability.     

Electroreduction of hexavalent chromium using a porous titanium flow-through electrode and intelligent prediction based on a back propagation neural network

● Titanium-based flow-through electrode achieved high Cr(VI) reduction efficiency. ● Flow-through pattern enhanced the mass transfer and reduced cathodic polarization. ● BPNN predicted the optimal electroreduction conditions of flow-through cell. Flow-through electrodes have been demonstrated to be effective for electroreduction of Cr(VI), but shortcomings are tedious preparation and short lifetimes. Herein, porous titanium available in the market was studied as a flow-through electrode for Cr(VI) electroreduction. In addition, the intelligent prediction of electrolytic performance based on a back propagation neural network (BPNN) was developed. Voltametric studies revealed that Cr(VI) electroreduction was a diffusion-controlled process. Use of the flow-through mode achieved a high limiting diffusion current as a result of enhanced mass transfer and favorable kinetics. Electroreduction of Cr(VI) in the flow-through system was 1.95 times higher than in a parallel-plate electrode system. When the influent (initial pH 2.0 and 106 mg/L Cr(VI)) was treated at 5.0 V and a flux of 51 L/(h·m²), a reduction efficiency of ~99.9% was obtained without cyclic electrolysis process. Sulfate served as the supporting electrolyte and pH regulator, as reactive CrSO₇²⁻ species were formed as a result of feeding HSO₄⁻. Cr(III) was confirmed as the final product due to the sequential three-electron transport or disproportionation of the intermediate. The developed BPNN model achieved good prediction accuracy with respect to Cr(VI) electroreduction with a high correlation coefficient (R² = 0.943). Additionally, the electroreduction efficiencies for various operating inputs were predicted based on the BPNN model, which demonstrates the evolutionary role of intelligent systems in future electrochemical technologies.     

Preparation of a permanent magnetic hypercrosslinked resin and assessment of its ability to remove organic micropollutants from drinking water

A rapid and effective method based on a novel permanent magnetic hypercrosslinked resin W150 was proposed for the removal of organic micropollutants in drinking water. W150 was prepared by suspension and post-crosslinking reaction and found to possess a high specific surface area of 1149.7 m²·g^-1, a small particle size of 50 μm to 100 μm, and a saturation magnetization as high as 8 emu·g^-1. W150 was used to eliminate nitrofurazone (NFZ) and oxytetracycline (OTC) from drinking water compared with commercial adsorbents XAD-4 and F400D. The adsorption kinetics of NFZ and OTC onto the three adsorbents well fitted the pseudo-second-order equation (r>0.972), and the adsorption isotherms were all well described by the Freundlich equation (r>0.851). Results showed that the reduction in adsorbent size and the enlargement in sorbent pores both accelerated adsorption. Moreover, the effect of particle size on adsorption was more significant than that of pore width. Given that the smallest particle size and the highest specific surface area were possessed by W150, it had the fastest adsorption kinetics and largest adsorption capacity for NFZ (180 mg·g^-1) and OTC (200 mg·g^-1). For the adsorbents with dominant micropores, the sorption of large-sized adsorbates decreased because of the inaccessible micropores. The solution pH and ionic strength also influenced adsorption.     

Selective recovery of Cu2+ and Ni2+ from wastewater using bioelectrochemical system

As the bioelectrochemical system, the microbial fuel cell (MFC) and the microbial electrolysis cell (MEC) were developed to selectively recover Cu²⁺ and Ni²⁺ ions from wastewater. The wastewater was treated in the cathode chambers of the system, in which Cu²⁺ and Ni²⁺ ions were removed by using the MFC and the MEC, respectively. At an initial Cu²⁺ concentration of 500 mg·L^-1, removal efficiencies of Cu²⁺ increased from 97.0%±1.8% to 99.0%±0.3% with the initial Ni²⁺ concentrations from 250 to 1000 mg·L^-1, and maximum power densities increased from 3.1±0.5 to 5.4±0.6 W·m^-3. The Ni²⁺ removal mass in the MEC increased from 6.8±0.2 to 20.5±1.5 mg with the increase of Ni²⁺ concentrations. At an initial Ni²⁺ concentration of 500 mg·L^-1, Cu²⁺ removal efficiencies decreased from 99.1%±0.3% to 74.2%±3.8% with the initial Cu²⁺ concentrations from 250 to 1000 mg·L^-1, and maximum power densities increased from 3.0±0.1 to 6.3±1.2 W·m^-3. Subsequently, the Ni²⁺ removal efficiencies decreased from 96.9%±3.1% to 73.3%±5.4%. The results clearly demonstrated the feasibility of selective recovery of Cu²⁺ and Ni²⁺ from the wastewater using the bioelectrochemical system.     

Upgrade of three municipal wastewater treatment lagoons using a high surface area media

Lagoon-based municipal wastewater treatment plants (WWTPs) are facing difficulties meeting the needs of rapid population growth as well as the more stringent requirements of discharge permits. Three municipal WWTPs were modified using a high surface area media with upgraded fine-bubble aeration systems. Performance data collected showed very promising results in terms of five-day biochemical oxygen demand (BOD₅), ammonia (NH₃) and total suspended solids (TSS) removal. Two-year average ammonia effluents were 4.1 mg·L^-1 for Columbia WWTP, 4 mg·L^-1 for Larchmont WWTP and 2.1 mg·L^-1 for Laurelville WWTP, respectively. Two- year average BOD₅ effluents were 6.8, 4.9 and 2.7 mg·L^-1, and TSS effluents were 15.0, 9.6 and 7.5 mg·L^-1. The systems also showed low fecal coliform (FC) levels in their effluents.