PM<Subscript>10</Subscript> and Ultrafine Particles Counts In-Vehicle and On-Road in the Athens Area

This work presents the first results of a study concerning on-road and in-vehicle exposure to particulate matter in the area of Athens. PM₁₀ concentration measurements were conducted by TSI DustTrak, while driving along routes with different characteristics of traffic density, during September 2003–March 2004. Concurrent measurements of the ultrafine particles (UFPs) number concentration were also conducted, by condensation particle counter during part of the days. Pedestrian exposure to PM₁₀ and UFPs was also studied through stationary measurements on the kerbside of selected roads on November 2003 and February 2004. A major avenue, a heavy-trafficked road across a children hospital and two central roads, one in a residential and one in a commercial area were selected for measurement. The results indicate that every day commuters are exposed to significant concentration levels. Higher exposures were observed in heavy-trafficked areas and during rush hours. Mean PM₁₀ in-vehicle and on-road concentrations ranged from 30–320 μg/m³ and 70–285 μg/m³, respectively. The ultrafine particles number concentrations were in the range of 5.0 × 10⁴–17.3 × 10⁴ particles/cm³ in-vehicle and 3.1 × 10⁴–7.3 × 10⁴ particles/cm³ on the kerbside of a central residential road. Both PM₁₀ and UFPs concentrations presented repeated short-term peak exposures. The results clearly point out the importance of the road microenvironment (in-vehicle and on kerbside) for population exposure in urban areas.     

Dynamic studies on lead volatilization from CaO–SiO2–Al2O3 molten slag under N2–CO–CO2, N2–HCl and N2–H2S gas atmospheres

Dynamic studies on the volatilization of lead from CaO–SiO₂–Al₂O₃ molten slags were conducted in a lab-scale melting furnace from 1623 to 1773 K under different mixed gas atmospheres of CO 0.05–0.3 atm to CO₂ 0–0.3 atm to N₂ (balance), HCl 1.7 × 10^?3–6.7 × 10^?3 atm to N₂ (balance), and H₂S 3.0 × 10^?4 to 1.7 × 10^?3 atm to N₂ (balance). The slag samples consisted of the mixed powders of 20–50 wt% CaO, 30–60 wt% SiO₂, and 10–40 wt% Al₂O₃, containing 2000 ppm PbO.Results showed that the rates of volatilization of lead from the CaO–SiO₂–Al₂O₃ molten slags under the N₂–CO–CO₂, N₂–HCl, and N₂–H₂S gas atmospheres were higher than those under the simulated air (N₂–O₂), which increased with CO, HCl, and H₂S partial pressures. At \(p_{{HCl}}\)  =  \(p_{H_{2}S}\)  = 1.7 × 10^?3 atm, the apparent rate constants for the volatilization of lead under the N₂–H₂S and N₂–HCl gas atmospheres were nearly equal, which increased with a rise in temperature. Results also showed that the rate of volatilization of lead from the molten slag decreased drastically with the increasing viscosity of the molten slag, in the viscosity range lower than 3 Pa s. Consequently, the volatilization of lead from the CaO–SiO₂–Al₂O₃ molten slag was significantly influenced by CO, HCl, and H₂S partial pressures and by the viscosity of the molten slag.     

Indoor Air Quality Assessment of Elementary Schools in Curitiba, Brazil

The promotion of good indoor air quality in schools is of particular public concern for two main reasons: (1) school-age children spend at least 30% of their time inside classrooms and (2) indoor air quality in urban areas is substantially influenced by the outdoor pollutants, exposing tenants to potentially toxic substances. Two schools in Curitiba, Brazil, were selected to characterize the gaseous compounds indoor and outdoor of the classrooms. The concentrations of benzene, toluene, ethylbenzene, and the isomers xylenes (BTEX); NO₂; SO₂; O₃; acetic acid (HAc); and formic acid (HFor) were assessed using passive diffusion tubes. BTEX were analyzed by gas chromatography–ion trap mass spectrometry and other collected gasses by ion chromatography. The concentration of NO₂ varied between 9.5 and 23?µg m^?3, whereas SO₂ showed an interval from 0.1 to 4.8?µg m^?3. Within the schools, BTEX concentrations were predominant. Formic and acetic acids inside the classrooms revealed intermediate concentrations of 1.5?µg m^?3 and 1.2?µg m^?3, respectively.     

Preliminary environmental impact assessment of PFOS waste treatment in a lab-scale batch subcritical water decomposition operation

Life cycle assessment (LCA) was carried out by SimaPro 7.3 to study the environmental impact of a lab-scale batch subcritical water decomposition operation for a kilogram of Perfluorooctane sulfonic acid (PFOS) waste treatment in this study, a proven process for the decomposition of PFOS pollutants with high concentration. This LCA focuses on not only the main environmental factors from emissions of toxic pollutants, but also the influence from technical characteristics of the iron-induced subcritical water technology including energy and substances consumption during the subcritical water decomposition treatment process. The IMPACT 2002+ environmental model was used to evaluate the 15 midpoint and 4 end-point environmental damages. It was found that the energy consumption to sustain the high temperature (350 °C) and high pressure (23 MPa) in the subcritical water process contributes 99.8 % of the damages. The total negative impact of the SCWD process for 1 kg of PFOS waste treatment to human health, ecological quality, climate change and resources amounts to 1.11 × 10^?3, 8.43 × 10^?5, 9.76 × 10^?4, 9.05 × 10^?4 Pt, respectively. And the improvement of energy efficiency and catalytic effectiveness are two important factors to reduce the environmental impact from the SCWD process for the treatment of PFOS waste.     

Comparison of three ornamental plants for phytoextraction potential of chromium removal from tannery sludge

Based on pre-experimentation, three ornamental plants, Mirabilis jalapa, Impatiens Balsamin (I. Balsamin) and Tagetes erecta L., were selected as target plants to study the phytoextraction of chromium (Cr) in tannery sludge irrigated with four treatments according to Cr concentration gradient [Control (CK); 20.50 × 10³ mg kg^?1 (T1); 51.25 × 10³ mg kg^?1 (T2); 102.50 × 10³ mg kg^?1 (T3)]. Results of pot experiments showed that the biomass of Mirabilis jalapa and Tagetes erecta L. had no significant differences among the four treatments, while I. Balsamin showed a decline trend in the biomass with the increase of Cr concentration, probably due to some extent to the poisoning effect of Cr under treatment T2 or T3. Mirabilis jalapa accumulated Cr concentration, with 408.97, 124.97, 630.16 and 57.30 mg kg^?1 in its roots, stems, leaves and inflorescence, respectively. The translocation factor and the bioaccumulation coefficient of Mirabilis jalapa are each greater than 1, indicating that Mirabilis jalapa has the strong ability to tolerate and enrich Cr by biological processes. Comparing accumulation properties of the three ornamental plants, in the amount and allocation, Mirabilis jalapa showed the highest phytoextraction efficiency and could grow well at the high Cr concentration. Our experiments suggest that Mirabilis jalapa is the expected flower species for Cr removal from tannery sludge.     

Biodegradability of Epoxidized Soybean Oil Based Thermosets in Compost Soil Environment

In this study, bio-thermoset from epoxidized soybean oil (ESO) was prepared in the presence of methylhexahydrophthalic anhydride curing agent and 2-ethyl-4-methylimidazole catalyst. The crosslink densities of the synthesized ESO are ranged from 0.109 × 10^?3 to 0.308 × 10^?3 mol/cm³. The ESO bio-thermosets were exposed to the soil-burial test for 8 months. Weight change and morphology of the degraded ESO specimens were assessed. It was found that the weight loss of ESO was governed by the materials compositions, crosslink density and the soil-burial exposure time. The 3 mm thickness ESO bio-thermosets with crosslink density of 0.109 × 10^?3 mol/cm³ had fully biodegraded after soil-burial for 6 months. In addition, 16S rDNA sequencing was carried out to identify the soil microorganisms. It was suggested that Comamonas sp., Bacillus sp., Streptomyces sp. and Acinetobacter sp. are the possible soil microbes that degrade the ESO bio-thermosets in the compost soil environment.     

Kinetic Analysis of the Temperature Effect on Polyhydroxyalkanoate Production by <Emphasis Type="Italic">Haloferax mediterranei</Emphasis> in Synthetic Molasses Wastewater

Haloferax mediterranei is an extremely halophilic archaeon that is able to synthesize polyhydroxyalkanoate (PHA) in high salt environment with low sterility demand. In this study, a mathematical model was validated and calibrated for describing the kinetic behavior of H. mediterranei at 15, 20, 25, and 35 °C in synthetic molasses wastewater. Results showed that the production of PHA by H. mediterranei, ranging from 390 to 620 mg h^?1 L^?1, was strongly dependent on the temperature. The specific growth rate (µ _max), specific substrate utilization rate (q _max), and specific decay rate (k _d) of H. mediterranei increased with temperature following Arrhenius equation prediction. The estimated activation energy was 58.31, 25.59, and 22.38 kJ mol^?1 for the process of cell growth, substrate utilization, and cell decay of H. mediterranei, respectively. The high temperature triggered the increased PHA storage even without nitrogen limitation. Thus, working at high temperatures seems a good strategy for improving the PHA productivity of H. mediterranei.     

Synthesis of Gum Acacia Capped Polyaniline-Based Nanocomposite Hydrogel for the Removal of Methylene Blue Dye

In this research work, a novel gum acacia capped polyaniline-based nanocomposite hydrogel (GPA NCHs) was developed and evaluated for the adsorptive removal of cationic methylene blue dye (MB) from aqueous solutions. Firstly, Gum acacia (GA) capped Polyaniline (PANI) dispersion was synthesized by using dispersion polymerization. Then, a water-swellable hydrogel network consisting of GA-PANI and acrylamide (AM) was obtained by using N,N′ -methylene-bisacrylamide (MBA) as a cross-linker, and ammonium persulphate/N,N,N′,N′-tetramethylethylenediamine (APS/TMEDA) as an initiating system. The developed materials were characterized by UV–visible, FTIR, XRD, SEM–EDX and TEM techniques. The microscopy studies revealed that GA-PANI nanoparticles have a granular morphological surface with an average size of?~?40–100 nm. Removal of MB dye from aqueous system was performed by adsorption studies in batch equilibrium mode with different dosage of GA-PANI, MB concentration, pH and temperatures. The adsorption data revealed that the absorption capacity of GPA NCHs highly depends on the dosage of GA-PANI, pH and concentration of the MB dye. The maximum percentage of MB removal onto GPA 1.0 NCHs was found to be 89% at pH 10 with a dye concentration of 10 mg L^?1. The equilibrium adsorption data were also analyzed by different models to understand the adsorption process. The results revealed that the adsorption process followed the pseudo-second-order kinetics and it fit well in Langmuir and Freundlich adsorption isotherms with a maximum adsorption capacity of 35.41 mg g^?1. These studies demonstrate that the GPA NCHs could be a promising adsorbent material for the removal of MB dye from contaminated aqueous systems.

     

An Original Halo-Alkaline Protease from <Emphasis Type="Italic">Bacillus halodurans</Emphasis> Strain US193: Biochemical Characterization and Potential Use as Bio-Additive in Detergents

Over a hundred of halophilic/halotolerant microorganisms were screened for alkaline protease production. The bacterium showing the highest enzyme production was characterized and identified as Bacillus halodurans US193 on the basis of 16S rRNA gene analysis. It was alkalophilic, thermophilic and halotolerant since it grew optimally at pH 9.7 and 50?°C with tolerance of up to 125 g NaCl l^?1. The alkaline protease was purified 4.9 times with about 40186.1 U/mg as specific activity. It exhibited optimal activity at pH 10, 70?°C and 0.25 M NaCl with perfect stability at wide ranges of pH (6–12), temperatures (30–60?°C) and NaCl concentrations (0–2 M). The serine alkaline protease maintained high stability in the presence of Cu²⁺, Mg²⁺, Ba²⁺ and Ca²⁺ ions, various organic solvents [50% (v/v)] and ionic and non ionic detergent additives. In addition, it was more compatible with various commercialized detergents than other reported detergent proteases, and was very efficient in blood stain removal. These findings let B. halodurans US193 alkaline protease be an ideal candidate for many industrial processes at harsh conditions, especially as a bio-additive in detergent industry.     

Citric Acid and Vitamin C as Coupling Agents for the Surface Coating of ZrO<Subscript>2</Subscript> Nanoparticles and Their Behavior on the Optical,Mechanical, and Thermal Properties of Poly(vinyl alcohol) Nanocomposite Films

A series of bio-nanocomposites (BNC)s were fabricated through solution casting method. At first, the surfaces of ZrO₂ NPs were functionalized with citric acid and Vitamin C as green modifier agents. Then, PVA as polymer matrix was embedded with different contents (4, 8 and 12 wt%) of modified ZrO₂ (m-ZrO₂) NPs with the aim of ultrasonic irradiation process. The resulting BNCs were studied by various techniques. Thermal stability of obtained BNCs was enhanced after NPs’ addition to the PVA matrix. Optical activity of these new BNCs makes them potential candidate for UV shielding material. Lastly, the tensile strengths of the BNCs were increased in comparison to the pure PVA.     

Investigative studies for inert transformation of toxic chrysotile tailing

In an attempt to find ways to reduce consumption of natural raw material and recycle chrysotile tailing waste (CTW), cordierite ceramics were produced using CTW, kaolin tailing waste (KTW) and waste alumina. Before synthesizing the cordierite ceramics, the inert transformation of CTW was investigated via a thermal treatment. Experimental results indicated that CTW was converted into nonhazardous forsterite and enstatite at temperatures above 1000 °C. The characterizations of the synthesized cordierite ceramics were examined using thermal analyses, X-ray diffraction (XRD), morphological structure analyses, compressive strength measurement, coefficient of thermal expansion (CTE) and toxicity characteristic leaching procedure (TCLP). Thermal analyses indicated that significant weight loss below 900 °C was the release of structural water and gases. XRD indicated that the cordierite became the main crystalline phase at 1350 °C. Compressive strength test indicated that compressive strength of the cordierite ceramics was 260 MPa, and CTE of cordierite ceramics was 2.4 × 10^?6 °C^?1. This technology for the of utilization of CTW and KTW could be used to produce industrial cordierite ceramics, in accordance with the concepts of sustainable development.     

Tailor Made Thin Film Composite Membranes: Potentiality Towards Removal of Hydroquinone from Water

The study investigated the use of thin film composite membrane (TFC) as a potential candidate for hydroquinone removal from water. Thin film composite membranes were prepared by polyamide coating on Polysulfone asymmetric membrane. FTIR study was performed to verify the Polysulfone as well as polyamide functionality. TFC membrane was characterized by contact angle, zeta potential, scanning electron microscopy studies. The salt rejection trend was seen from 500 to 1000 mg/L. The membrane is marked by permeability co-efficient B based on solution diffusion studies. The value is 0.98 × 10^?6 m/s for NaCl solution at 1.4 MPa. The separation performance was 88.87% for 5 mg/L hydroquinone at 1.4 MPa. The separation was little bit lowered in acid medium because of the nature of the membrane and feed solute chemistry. The ‘pore swelling’ and ‘salting out’ influenced hydroquinone separation in the presence of NaCl. The hydroquinone separation was 80.63% in 1000 mg/L NaCl solution. In acidic pH, NaCl separation was influenced much more compared to hydroquinone. The separation is influenced by field water matrix.     

Enzyme-Assisted Extraction and Pb<Superscript>2+</Superscript> Biosorption of Polysaccharide from <Emphasis Type="Italic">Cordyceps militaris</Emphasis>

The enzyme assisted extraction conditions of polysaccharide from Cordyceps militaris mycelia were firstly investigated by kinetics analysis and the optimal operating was found to be: extraction temperature 40 °C; solid-solvent ratio 1:20; extraction pH 4.0; cellulase concentration 2.0%. The polysaccharide extraction yield was 5.99% under these optimized conditions. Furthermore, a fundamental investigation of the biosorption of Pb²⁺ from aqueous solution by the C. militaris polysaccharide was performed under batch conditions. The suitable pH (5.0), polysaccharide concentration (0.20 g L^?1), initial Pb²⁺ concentration (300 mg L^?1) and contact time (40 min) were outlined to enhance Pb²⁺ biosorption from aqueous medium. The Langmuir isotherm model and pseudo first order kinetic model fitted well to the data of Pb²⁺ biosorption, suggesting the biosorption of Pb²⁺ onto C. militaris polysaccharide was monolayer biosorption and physical adsorption might be the rate-limiting step that controlled the adsorption process. FTIR analysis showed that the main functional groups of C. militaris polysaccharide involved in adsorption process were carbonyl, carboxyl, and hydroxyl groups.     

Sunflower stalk, an agricultural waste, as an adsorbent for the removal of lead and cadmium from aqueous solutions

Sunflower residue, an agricultural waste material for the removal of lead (Pb) and cadmium (Cd) from aqueous solutions were investigated using a batch method. Adsorbent was prepared by washing sunflower residue with deionized water until the effluent was colorless. Batch mode experiments were carried out as a function of solution pH, adsorbent dosage, initial concentration and contact time. The results indicated that the adsorbent showed good sorption potential and maximum metal removal was observed at pH 5. Within 150 min of operation about 97 and 87 % of Pb and Cd ions were removed from the solutions, respectively. Lead and Cd sorption curves were well fitted to the modified two-site Langmuir model. The adsorption capacities for Pb and Cd at optimum conditions were 182 and 70 mg g^?1, respectively. The kinetics of Pb and Cd adsorption from aqueous solutions were analyzed by fitting the experimental data to a pseudo-second-order kinetic model and the rate constant was found to be 8.42 × 10^?2 and 8.95 × 10^?2 g mg^?1 min^?1 for Cd and Pb, respectively. The results revealed that sunflower can adsorb considerable amount of Pb and Cd ions and thus could be an economical method for the removal of Pb and Cd from aqueous systems.     

Effect of aeration rate and moisture content on the emissions of selected VOCs during municipal solid waste composting

The influence of the industrial control composting conditions (aeration 0.005–0.300?L_air?kg^?1 and moisture 40–70?%) of municipal solid waste on the composition of the selected compound emitted (limonene, β-pinene, 2-butanone, undecane, phenol, toluene, dimethyl sulfide, dimethyl disulfide) was studied. The highest emissions of volatile organic compounds (VOCs) were observed in the early stages of the processes. At the end of the process, low concentrations of the emitted compounds were found. Aeration rate had a strong effect on emissions. High aeration rate (0.300?L_air?kg^?1?min^?1) caused normally high emissions of all selected compounds whereas low aeration rates (0.05?L_air?kg^?1?min^?1) could cause anaerobiosis problems and generation of organic sulphur compounds. We observed that the effect of the moisture upon the emitted concentrations varied depending on the studied compound.     

Preparation and characterization of high surface area activated carbon from pine wood sawdust by fast activation with H<Subscript>3</Subscript>PO<Subscript>4</Subscript> in a spouted bed

Activated carbons were produced from waste pine wood sawdust using fast activation with H₃PO₄ in a spouted bed. In this study, activation temperature was set as 800 °C, and activation time ranged from 1 to 15 min. Experimental results show that sawdust impregnated with higher mass ratio of H₃PO₄ would be agglomerated in spouted bed, and difficult to fluidize. Therefore, an amount of quartz sand was added to assist for good fluidization. Fluidization of particle can improve the BET surface area or micropore volume of activated carbons. High BET surface area activated carbons can be obtained with activation time of only 1–5 min by combining the fluidization and H₃PO₄ fast activation. The obtained activated carbons contained developed pore structure and abundant surface functional groups (carboxyl, carbonyl and P-containing groups) by SEM–EDS, FTIR and XPS techniques. The particles of impregnation ratio of 1:1 can achieve fluidization without adding the quartz sand, which was convenient for experimental operation and even industrial production, and the BET surface area can reach more than 1000 m²/g in activation time of only 5 min.     

Recycling nickel from spent catalyst of Phu My fertilizer plant as a precursor for exhaust gas treatment catalysts preparation

In this study, a very promising way of treating and recycling spent nickel catalysts of fertilizer plants in Vietnam was proposed. Firstly, nickel was recovered from spent catalyst using HNO₃—leaching process. Results show that nickel recovery of over 90% with a purity of over 90% can be achieved with HNO₃ 2.1–2.5 M at 100?°C in 75 min. The residue after leaching is not considered as a hazardous waste according to the Vietnamese regulations. Then, the leachate solution was used as a precursor to prepare a model catalyst for exhaust gas (CO, HC, NO_x) treatment. In comparison with the catalyst prepared from the commercial nickel nitrate solution, the catalyst synthesized from recovered nickel exhibits similar properties and activities. The influence of Ni loading of Ni/alumina catalyst as well as the modification of active phase by some metals addition (Mn, Ba, Ce) was also investigated. It is feasible to modify active phase by transition metals such as Mn, Ba, and Ce for complete oxidation of CO and HC at 270?°C and a reduction of NO_x below 350?°C at high volumetric flow condition (GHSV?=?110.000 h^?1).     

TSP,PM<Subscript>10</Subscript> and health risk assessment for heavy metals (Cr,Ni, Cu,Zn, Cd,Pb) in the ambience of the production line for waste cathode ray tube recycling

Recently, a typical semi-automatic recycling line is proved to be a feasible method for resource recovery of raw material of waste CRTs. However, there are no relevant studies about health risk assessment of the particles and heavy metals diffused from this physical recycling process for CRTs. In this study, TSP, PM₁₀ and heavy metals (Cr, Ni, Cu, Zn, Cd and Pb) in the ambience of the workshop have been evaluated. The mean concentrations of TSP and PM₁₀ in the workshop were 481.5 and 316.9 μg/m³, respectively. Meanwhile, it can be seen that Zn (8.1 and 7.9 μg/m³, respectively) was the most enriched metal in TSP and PM₁₀, followed by Pb (3.2 and 3.0 μg/m³, respectively). Health risk assessment showed that the total hazard index was 3.29, exceeding the danger threshold. The health risk of different metals was Cr > Cd > Ni. In short, the research results show that mechanical–physical process for e-waste recycling do exist the pollutant mission. So the effective measures should be taken to reduce the harm of pollutants on the workers’ health.     

Magnetic Cr(VI) Ion Imprinted Polymer for the Fast Selective Adsorption of Cr(VI) from Aqueous Solution

In this study, a novel magnetic Cr(VI) ion imprinted polymer (Cr(VI)-MIIP) was successfully synthesized and used as a selective sorbent for the adsorption of Cr(VI) ions from aqueous solution. It can be synthesized through the combination of an imprinting polymer and magnetic nanoparticles. The high selectivity achieved using MIIP is due to the specific recognition cavities for Cr(VI) ions created in Cr(VI)-MIIP. Also, the magnetic properties that could be obtained using magnetic nanoparticles, helps to separate adsorbent with an external magnetic field without either additional centrifugation or filtration procedures. The magnetic Fe₃O₄ nanoparticles (MNPs) were synthesized using an improved co-precipitation method and modified with tetraethylorthosilicate (TEOS) before imprinting. The magnetic Cr(VI) ion imprinted polymer was prepared through precipitation copolymerization of 4-vinylpyridine as the complexing monomer, 2-hydroxyethyl methacrylate as a co-monomer, the Cr⁶⁺ anion as a template, and ethylene glycol dimethacrylate (EGDMA) as a cross-linker in the presence of modified magnetite nanoparticles. This novel synthesized sorbent was characterized using different techniques. Batch adsorption experiments were performed to evaluate the adsorption conditions, selectivity, and reusability. The results showed that the maximum adsorption capacity was 39.3 mg g^?1, which was observed at pH 3 and at 25?°C. The equilibrium time was 20 min, and the amount of adsorbent which gave the maximum adsorption capacity was 1.7 g L^?1. Isotherm studies showed that the adsorption equilibrium data were fitted well with the Langmuir adsorption isotherm model and the theoretical maximum adsorption capacity was 44.86 mg g^?1. The selectivity studies indicated that the synthesized sorbent had a high single selectivity sorption for the Cr(VI) ions in the presence of competing ions. Thermodynamic studies revealed that the adsorption process was exothermic (\(\Delta H\)?<?0) and spontaneous (\(\Delta G\)?<?0). In addition, the spent MIIP can be regenerated up to five cycles without a significant decrease in adsorption capacity.     

Stability of Aqueous Suspensions of Medium-Chain-Length Poly-3-Hydroxyalkanoate Particles

Although poly-3-hydroxyalkanoates (PHAs) and particularily medium-chain-length (mcl)-PHAs are likely to find industrial applications in a latex form, very few studies have examined their behavior in aqueous suspension and none have examined the dense suspensions required commercially. For this reason, the stability of mcl-PHA latexes containing saturated aliphatic (65 mol% 3-hydroxynonanoate, PHN), and for the first time, with vinyl (PHNU) or carboxylated side chains was examined. At 4 g L^?1 with no stabilizing agent, PHNU nanoparticles (199.4 ± 3.6 nm) were significantly smaller than those of PHN (211.5 ± 6.4 nm) while carboxylated PHN nanoparticles (76.1 ± 6.4 nm) were substantially smaller than those of either PHN or PHNU with particles stable for more than 110 days. Increasing the PHN concentration to 10 g L^?1 also resulted in stable latexes but with larger particles (410.8 ± 5.2 nm). Adjusting the pH of the suspending medium (water) before addition of the polymer (dissolved in acetone) resulted in much smaller PHN particles at pH = 11.3 (134 ± 2 nm) than at pH = 4.3 (312 ± 8 nm) at a 4 g L^?1 final polymer concentration. Zeta potentials of PHN suspensions decreased with pH, likely due to the carboxyl end groups. Above a pH of 4.0, adjusting the pH after particle formation had little effect. NaCl addition could be used to agglomerate and ultimately precipitate the particles. Stabilizers such as surfactants will likely be required to produce denser mcl-PHA latexes with suitable particle size for certain applications such as coatings and toner production.