Characteristics of pipe corrosion scales in untreated water distribution system and effect on water quality in Peshawar,Pakistan

This study investigated the characteristics of iron corrosion scales in pipes at tube well, overhead tank, and consumers’ end in older untreated water distribution system in Peshawar city, Pakistan. Effect of water quality conditions on corrosion scales and that of scales on drinking water quality in such systems was also assessed by undertaking a comparison with new piped distribution systems. The scales were analyzed for chemical composition and morphology using X-ray diffraction (XRD), inductively coupled plasma (ICP), and a scanning electron microscope (SEM), while water quality was examined for physicochemical and biological characteristics. The main crystalline phases of corrosion scales were goethite, magnetite, siderite, and quartz. From tube well to consumers’ end, goethite increased from 36 up to 48%, quartz declined from 22 to 15%, while magnetite fluctuated and siderite disappeared. Elemental composition of scales showed the deposition of Zn, Al, Mn, Cr, Pb, Cu, As, and Cd with Zn (13.9 g/kg) and Al (3.6 g/kg) in highest proportion. The SEM analysis illustrated the presence of microbial communities indicating the formation of biofilms in the corrosion scales. The significant difference (P <?0.05) in levels of dissolved oxygen (DO), Cl^?, SiO₄^4?, electrical conductivity (EC), SO₄^2?, NO₃^?, alkalinity, hardness, and trace metals between old (DS-O) and new piped systems indicated their role in corrosion scale formation/destabilization and the effect of scale dissolution on water quality. In DS-O, EC, Cu, and Mn were significantly higher (P?<?0.05), whereas turbidity, EC, DO, and SiO₄^4? significantly increased from source to consumers’ end implying a higher dissolution of scales and lowered corrosion rates in DS-O to utilize SiO₄^4? and DO for iron oxidation.

     

Cadmium (Cd2+) removal by nano zerovalent iron: surface analysis, effects of solution chemistry and surface complexation modeling

Nano zerovalent iron (nZVI) is an effective remediant for removing various organic and inorganic pollutants from contaminated water sources. Batch experiments were conducted to characterize the nZVI surface and to investigate the effects of various solution properties such as pH, initial cadmium concentration, sorbent dosage, ionic strength, and competitive ions on cadmium removal by nZVI. Energy-dispersive X-ray and X-ray photoelectron spectroscopy results confirmed removal of Cd²⁺ ions by nZVI through adsorption. Cd²⁺ adsorption decreased in the presence of competitive cations in the order: Zn²⁺?>?Co²⁺?>?Mg²⁺?>?Mn²⁺?=?Cu²⁺?>?Ca²⁺?>?Na²⁺?=?K⁺. Higher concentrations of Cl^? significantly decreased the adsorption. Cadmium removal increased with solution pH and reached a maximum at pH 8.0. The effects of various solution properties indicated Cd²⁺ adsorption on nZVI to be a chemisorption (inner-sphere complexation) process. The three surface complexation models (diffuse layer model, constant capacitance model, and triple layer model) fitted well to the adsorption edge experimental data indicating the formation of nZVI–Cd bidentate inner-sphere surface complexes. Our results suggest that nZVI can be effectively used for the removal of cadmium from contaminated water sources with varying chemical conditions.     

Possible particulate nitrite formation and its atmospheric implications inferred from the observations in Seoul,Korea

Simultaneous measurements of gaseous species and fine-mode, particulate inorganic components were performed at the University of Seoul, Seoul in Korea. In the simultaneous measurements, a certain level of nitrous acid (HONO) was observed in the gas-phase, indicating possible heterogeneous HONO production on the surface of the ambient aerosols. On the other hand, high particulate nitrite (NO^2?) concentrations of 1.41(±2.26) μg/m³ were also measured, which sometimes reached 18.54 μg/m³. In contrast, low HONO-to-NO₂ ratios of 0.007(±0.006) were observed in Seoul. This indicates that a significant fraction of HONO is dissolved in atmospheric aerosols. Around the Seoul site, sufficient alkalinity may have been provided to the atmospheric aerosols from the excessive presence of NH₃ in the gas-phase. Due to the alkaline particulate conditions (defined in this study as a particle pH >～3.29), the HONO molecules produced at the surface of the atmospheric aerosols appeared to have been converted into particulate nitrite, thereby preventing their further participation in the atmospheric O₃/NO_y/HO_x photochemical cycles. It was estimated that a minimum average of 65% of HONO was captured by alkaline, anthropogenic, urban particles in the Seoul measurements.     

Photocatalytic degradation of the herbicide pendimethalin using nanoparticles of BaTiO3/TiO2 prepared by gel to crystalline conversion method: A kinetic approach

Photocatalytic degradation of the herbicide, pendimethalin (PM) was investigated with BaTiO₃/TiO₂ UV light system in the presence of peroxide and persulphate species in aqueous medium. The nanoparticles of BaTiO₃ and TiO₂ were obtained by gel to crystallite conversion method. These photo catalysts are characterized by energy dispersive x-ray analysis (EDX), scanning electron microscope (SEM), x-ray diffraction (XRD), and Brunauer-Emmett-Teller (BET) adsorption isotherm and reflectance spectral studies. The quantum yields for TiO₂ and BaTiO₃ for the degradation reactions are 3.166 Einstein m^?2 s^?1 and 2.729 Einstein m^?2 s^?1 and catalytic efficiencies are 6.0444 × 10^?7 mg^?2h^?1L² and 5.403 × 10^?7 mg^?2h^?1L², respectively as calculated from experimental results. BaTiO₃ exhibited comparable photocatalytic efficiency in the degradation of pendimethalin as the most widely used TiO₂ photocatalyst. The persulphate played an important role in enhancing the rate of degradation of pendimethalin when compared to hydrogen peroxide. The degradation process of pendimethalin followed the first-order kinetics and it is in agreement with Langmuir-Hinshelwood model of surface mechanism. The reason for high stability of pendimethalin for UV-degradation even in the presence of catalyst and oxidizing agents were explored. The higher rate of degradation was observed in alkaline medium at pH 11. The degradation process was monitored by spectroscopic techniques such as ultra violet-visible (UV-Vis), infrared (IR) and gas chromatography mass spectroscopy (GC-MS). The major intermediate products identified were: N-propyl-2-nitro-6-amino-3, 4-xylidine, (2, 3-dimethyl-5-nitro-6-hydroxy amine) phenol and N-Propyl-3, 4-dimethyl-2, 6-dinitroaniline by GC-MS analysis and the probable reaction mechanism has been proposed based on these products.     

Formation potentials of bromate and brominated disinfection by-products in bromide-containing water by ozonation

The ozonation involved in drinking water treatment raises issues of water quality security when the raw water contains bromide (Br^?). Br^? ions may be converted to bromate (BrO₃ ^?) during ozonation and some brominated disinfection by-products (Br-DBPs) in the following chlorination. In this study, the effects of ozone (O₃) dosage, contact time, pH, and Br^? and ammonia (NH₃-N) concentrations on the formation of BrO₃ ^? and Br-DBPs have been investigated. The results show that decreasing the initial Br^? concentration is an effective means of controlling the formation of BrO₃ ^?. When the concentration of Br^? was lower than 100 μg/L, by keeping the ratio of O₃ dosage to dissolved organic carbon (DOC) concentration at less than 1, BrO₃ ^? production was effectively suppressed. The concentration of BrO₃ ^? steadily increased with increasing O₃ dosage at high Br^? concentration (>900 μg/L). Additionally, a longer ozonation time increased the concentrations of BrO₃ ^? and total organic bromine (TOBr), while it had less impact on the formation potentials of brominated trihalomethanes (Br-THMFP) and haloacetic acids (Br-HAAFP). Higher pH value and the presence of ammonia may lead to an increase in the formation potential of BrO₃ ^? and Br-DBPs.     

Comparison of modeling with empirical calculation of diffuse and fugitive methane emissions in a Spanish landfill

One of the most significant environmental problems arising from landfills is the emission of methane into the atmosphere. In this study, methane emissions from a currently in-use Spanish landfill were modeled as well as being experimentally measured using a two-step method. The first step involved a qualitative walkover survey to detect where gases were being emitted on the surface of the landfill. The second stage comprised a quantitative analysis of these surface methane emissions at a selected number of points on the landfill surface using a specially designed flux chamber. The statistical analysis of the data obtained was based on the Sichel function and resulted in an average emission rate of 74.9 g·m^?2·day^?1, with 27.8 and 202.1 g·m^?2·day^?1 as the lower and upper limits of the 95% confidence interval, respectively. The total emission for the landfill, with an emitting surface of 335,000 m², is 9.16 × 10³ ton/yr. These values have been compared with those from three different models, with the model results being above the calculated mean emissions measured at the landfill, but below the upper confidence limit at 95%.

Implications: One of the main environmental problems arising from the presence of landfills is the emission of biogas (which mainly contains methane and carbon dioxide) into the atmosphere. Several experimental methods as well as models have been developed to quantify these emissions. In this work, the authors have compared the results obtained using experimental measurements with those provided by some local and international models using the default parameters proposed. The results obtained from the experimental method are in accordance with those provided by the models, although the models could be slightly overestimating these emissions.     

Role of some organic inhibitors on the oxidation of dissolved sulfur dioxide by oxygen in rainwater medium

In August 2012, eight rainwater samples were collected and analyzed for pH and metal ions, viz., iron, copper, and manganese. The pH was within the range 6.84–7.65. The rate of oxidation of dissolved sulfur dioxide was determined using these rainwater samples as reaction medium. Kinetics was defined by the rate law: ?d[S(IV)]/dt = R _o = k _o[S(IV)]], where k _o is the first-order rate constant and R _o is the rate of the reaction. The effect of two volatile organic compounds—ethanol and 2-butanol—was examined and found to inhibit the oxidation as defined by the rate law: k _obs = k _o/(1 + B [Inh]), where k _obs is the first-order rate constant in the presence of the inhibitor, [Inh] is the concentration of the inhibitor, and B is the inhibitor parameter—an empirical constant. In the pH range of collected rainwater samples, the values of first-order rate constants ranged from 3.1?×?10^?5 to 1.5?×?10^?4 s^?1 at 25 °C. The values of inhibition parameter were found to be (5.99?±?3.91?×?10⁴) (ethanol) and (3.95?±?2.36)?×?10⁴ (2-butanol) at 25 °C.     

Effect of Tinospora cordifolia on the reduction of ultraviolet radiation‐induced cytotoxicity and DNA damage in PC12 cells

The safety of Tinospora cordifolia and its potential to protect against ultraviolet radiation‐induced cytotoxicity and DNA damage in PC12 cells were investigated. To evaluate the safety of T. cordifolia, cell viability and agarose gel electrophoresis were carried out using PC12 cells treated with 0 to 100 μg mL^?1 of methanol extract of T. cordifolia. T. cordifolia extracts did not show cytotoxicity ranging 0 to 100 μg mL^?1. In addition, T. cordifolia extracts significantly increased cell viability at 1 ng, 10 ng and 1 μg mL^?1 concentrations in serum‐deprived medium compared to control. To confirm the protective role against UV‐induced damage, PC12 cells alone or in the presence of 10 ng, 100 ng, or 1 μg mL^?1 of T. cordifolia extract were exposed to 250, 270 and 290 nm of UV radiation, which corresponded to doses of 120, 150 and 300 mJ cm^?2, respectively. Treatment with T. cordifolia extracts significantly increased the cell survival rate irradiated at 290 nm. In addition, T. cordifolia extracts significantly reduced cyclobutane pyrimidine dimer formation induced by UV irradiation at all wavelengths. In conclusion, T. cordifolia is not toxic and safe for cells. Our findings can support its application as phototherapy in the medical sector.     

Co-metabolic transformation of the neonicotinoid insecticide imidacloprid by the new soil isolate Pseudoxanthomonas indica CGMCC 6648

A new imidacloprid (IMI) degrading bacterium Z-9 (deposited number CGMCC 6648) was isolated and identified as Pseudoxanthomonas indica by 16S rRNA gene analysis. Two metabolites were identified as olefin and 5-hydroxy IMI by liquid chromatography-mass spectrometry and nuclear magnetic resonance analysis. P. indica CGMCC 6648 degraded 70.1% of IMI (1.22 mmol L^?1) and formed 0.93 mmol L^?1 5-hydroxy IMI and 0.05 mmol L^?1 olefin IMI in 6 days and in the presence of 100 mmol L^?1 glucose. The half-life of IMI degradation was 3.6 days. P. indica CGMCC 6648 transforms IMI via a co-metabolism mechanism and different carbohydrates have significant effects on 5-hydroxy IMI formation, whereas different organic acids have substantial effects on olefin IMI production. Lactose is the best co-substrate for IMI degradation and 5-hydroxy IMI formation with 0.77 mmol L^?1 degraded and 0.67 mmol L^?1 formed in 48 h, respectively. Pyruvate is the best co-substrate for olefin IMI formation with 0.17 mmol L^?1 produced in 96 h for all carbon sources tested. Pyruvate significantly stimulates the conversion of 5-hydroxy IMI to olefin IMI, whereas glucose slightly inhibits this reaction. P. indica CGMCC 6648 rapidly degrades IMI and forms olefin IMI, which may enhance its potential for biodegradation of IMI and increase its insecticidal activity, which can decrease the IMI dosage required.     

Reactive uptake of ozone at simulated leaf surfaces: Implications for ‘non-stomatal’ ozone flux

The reaction of ozone (O₃) with α-pinene has been studied as a function of temperature and relative humidity and in the presence of wax surfaces that simulate a leaf surface. The objective was to determine whether the presence of a wax surface, in which α-pinene could dissolve and form a high surface concentration, would lead to enhanced reaction with O₃. The reaction of O₃ itself with the empty stainless steel reactor and with aluminium and wax surfaces demonstrated an apparent activation energy of around 30 kJ mol^?1 for all the surfaces, similar to that observed in long-term field measurements of O₃ fluxes to vegetation. However, the absolute reaction rate was 14 times greater for aluminium foil and saturated hydrocarbon wax surfaces than for stainless steel, and a further 5 times greater for beeswax than hydrocarbon wax. There was no systematic dependence on either relative or absolute humidity for these surface reactions over the range studied (20–100% RH). Reaction of O₃ with α-pinene occurred at rates close to those predicted for the homogeneous gas-phase reaction, and was similar for both the empty reactor and in the presence of wax surfaces. The hypothesis of enhanced reaction at leaf surfaces caused by enhanced surface concentrations of α-pinene was therefore rejected. Comparison of surface decomposition reactions on different surfaces as reported in the literature with the results obtained here demonstrates that the loss of ozone at the earth's surface by decomposition to molecular oxygen (i.e. without oxidative reaction with a substrate) can account for measured ‘non-stomatal’ deposition velocities of a few mm s^?1. In order to quantify such removal, the effective molecular surface area of the vegetation/soil canopy must be known. Such knowledge, combined with the observed temperature-dependence, provides necessary input to global-scale models of O₃ removal from the troposphere at the earth's surface.     

Ammonia Flux from Open-Lot Dairies: Development of Measurement Methodology and Emission Factors

Abstract

Ammonia emissions contribute to the formation of secondary particulate matter (PM) and violations of the National Ambient Air Quality Standard. Ammonia mass concentration measurements were made in February 1999 upwind and downwind of an open-lot dairy in California, using a combination of active bubbler and passive filter samplers. Ammonia fluxes were calculated from concentrations measured at 2, 4, and 10 m above ground at three locations on the downwind edge of the dairy, using micrometeorological techniques. A new method was developed to interpolate fluxes at six additional locations from ammonia concentrations measured at a single height, providing measurements at sufficient spatial resolution along the downwind border of the dairy to account for the heterogeneity of the source. PM measured up- and downwind of the dairy demonstrated insignificant ammonium particle formation in the immediate vicinity of the dairy and negligible contribution of dissociated ammonium nitrate to measured ammonia concentrations. Ammonium nitrate concentrations measured downwind of the dairy ranged from 26 to 0.26 μg m^?3 and from 2 to 43% of total PM_2.5 mass concentrations. Measured ammonia fluxes showed that liquid manure retention ponds represented relatively minor sources of ammonia in winter on the dairy studied. Ammonia emission factors derived from the measurements ranged from 19 to 143 g head^?1 day^?1, showing an increase with warmer, drier weather and a decrease with increased relative humidity and lower temperatures.     

Monitoring the Multi-Year Carbon Balance of a Subarctic Palsa Mire with Micrometeorological Techniques

This article reports a dataset on 8 years of monitoring carbon fluxes in a subarctic palsa mire based on micrometeorological eddy covariance measurements. The mire is a complex with wet minerotrophic areas and elevated dry palsa as well as intermediate sub-ecosystems. The measurements document primarily the emission originating from the wet parts of the mire dominated by a rather homogenous cover of Eriophorum angustifolium. The CO₂/CH₄ flux measurements performed during the years 2001–2008 showed that the areas represented in the measurements were a relatively stable sink of carbon with an average annual rate of uptake amounting to on average ?46 g C m^?2 y^?1 including an equally stable loss through CH₄ emissions (18–22 g CH₄–C m^?2 y^?1). This consistent carbon sink combined with substantial CH₄ emissions is most likely what is to be expected as the permafrost under palsa mires degrades in response to climate warming.     

The effects and the toxicity increases caused by bicarbonate,chloride, and other water components during the UV/TiO<Subscript>2</Subscript> degradation of oxazaphosphorine drugs

The influences of HCO₃ ^?, Cl^?, and other components on the UV/TiO₂ degradation of the antineoplastic agents ifosfamide (IFO) and cyclophosphamide (CP) were studied in this work. The results indicated that the presence of HCO₃ ^?, Cl^?, NO₃ ^?, and SO₄ ^2? in water bodies resulted in lower degradation efficiencies. The half-lives of IFO and CP were 1.2 and 1.1 min and increased 2.3–7.3 and 3.2–6.3 times, respectively, in the presence of the four anions (initial compound concentration = 100 μg/L, TiO₂ loading =100 mg/L, anion concentration = 1000 mg/L, and pH = 8). Although the presence of HCO₃ ^? in the UV/TiO₂/HCO₃ ^? system resulted in a lower degradation rate and less byproduct formation for IFO and CP, two newly identified byproducts, P11 (M.W. = 197) and P12 (M.W. = 101), were formed and detected, suggesting that additional pathways occurred during the reaction of ?CO₃ ^? in the system. The results also showed that ?CO₃ ^? likely induces a preferred ketonization pathway. Besides the inorganic anions HCO₃ ^?, Cl^?, NO₃ ^?, and SO₄ ^2?, the existence of dissolved organic matter in the water has a significant effect and inhibits CP degradation. Toxicity tests showed that higher toxicity occurred in the presence of HCO₃ ^? or Cl^? during UV/TiO₂ treatment and within 6 h of reaction time, implying that the effects of these two anions should not be ignored when photocatalytic treatment is applied to treat real wastewater.     

Climatology of PM2.5 organic carbon concentrations from a review of ground-based atmospheric measurements by evolved gas analysis

In this work we have compared ground-based measurements of organic carbon (OC) in the fine aerosol (PM2.5) fraction that are reported in peer-reviewed publications as part of both short campaigns and continuous monitoring networks. The comparison provides a quantitative review of global OC measurements for the purpose of establishing the extent to which organic aerosol concentrations are known with sufficient geographic and historical resolution to constrain global climate models. Only North America has sufficient measurements to provide meaningful spatial and temporal trends, although available measurements from China and Japan indicate that the Asian region is the most polluted with OC concentrations of approximately 10 μg m^?3. These measurements have a low spatial resolution, with most sites located in highly urban areas within a small geographic region. OC concentrations in North America are approximately 1 μg m^?3 and are better characterized spatially, temporally, and historically by continuous monitoring networks established decades ago. OC concentration shows a weakly increasing trend in some regions from 1997 to 2006, although in most regions it has remained effectively constant over the last ten years. Eastern U.S. sites show maximum OC in the winter and western U.S. sites show maximum OC in the summer. There is no correlation at U.S. sites between OC concentration and sulfate, nitrate, or ammonium ions, with R² < 0.1 in each case.     

Spectroscopic study of organic coatings on fine particles,exposed to ozone and simulated sunlight

This work intends to quantify the variation in optical properties of aerosol by in-situ spectroscopic monitoring the ozonolysis of a mixture of typical biomass burning compounds. The reaction occurs on silica and glass particles in the presence of simulated sunlight.Fused silica particles (Aerosil) were coated with a thin film of a 1:1 mixure of 4-phenoxyphenol with 4-carboxyphenone as a photosensitizer. UV–VIS spectra of dichloromethane extracts from the particles recorded before and after treatment, show development of a new band after prolonged ozone and light exposure.Changes in optical properties are reported, and variations of spectroscopic features are discussed. We show that the ozone-induced heterogeneous photochemical reaction does produce species absorbing light in the solar spectral range. Further, we demonstrate that the heterogeneous photosensitized reactions at 200 ppb ozone (strongly ozone polluted regions) for a time period of 7 h aging process, can increase light absorption of atmospheric aerosols in the tropospheric actinic window (>290 nm) by 0.4 absorption units ng-C^?1 O₃ ppm^?1 in the region 290–358 nm and by 1.0 absorption units ng-C^?1 O₃ ppm^?1 in the region 360–448 nm.Chemical changes of such surface films were identified by diffuse reflectance infrared Fourier transform spectroscopy of coated glass spheres, and we suggest formation of humic-like substances comparable to those reported in continental aerosol.     

Formation of indoor nitrous acid (HONO) by light-induced NO<Subscript>2</Subscript> heterogeneous reactions with white wall paint

Gaseous nitrogen dioxide (NO₂) represents an oxidant that is present in relatively high concentrations in various indoor settings. Remarkably increased NO₂ levels up to 1.5 ppm are associated with homes using gas stoves. The heterogeneous reactions of NO₂ with adsorbed water on surfaces lead to the generation of nitrous acid (HONO). Here, we present a HONO source induced by heterogeneous reactions of NO₂ with selected indoor paint surfaces in the presence of light (300 nm?<?λ?<?400 nm). We demonstrate that the formation of HONO is much more pronounced at elevated relative humidity. In the presence of light (5.5 W m^?2), an increase of HONO production rate of up to 8.6?·?10⁹ molecules cm^?2 s^?1 was observed at [NO₂]?=?60 ppb and 50 % relative humidity (RH). At higher light intensity of 10.6 (W m^?2), the HONO production rate increased to 2.1?·?10¹⁰ molecules cm^?2 s^?1. A high NO₂ to HONO conversion yield of up to 84 % was observed. This result strongly suggests that a light-driven process of indoor HONO production is operational. This work highlights the potential of paint surfaces to generate HONO within indoor environments by light-induced NO₂ heterogeneous reactions.     

Comparative effects on arsenic uptake between iron (hydro)oxides on root surface and rhizosphere of rice in an alkaline paddy soil

The iron (Fe) (hydro)oxides deposited around rice roots play an important role in arsenic (As) sequestration in paddy soils, but there is no systematic study on the relative importance of Fe (hydro)oxides on root surface and in rhizosphere soil in limiting As bioavailability. Twenty-seven rice genotypes were selected to investigate effects of Fe (hydro)oxides on As uptake by rice in an alkaline paddy soil. Results indicated that the As content was positively correlated with the Fe content on root surface, and most of As (88–97%) was sequestered by poorly crystalline and crystalline Fe (hydro)oxides in the alkaline paddy soil. The As sequestration by Fe (hydro)oxides on root surface (IAS_root 16.8–25.0 mg As/(g Fe)) was much higher than that in rhizosphere (IAS_rhizo 1.4–2.0 mg As/(g Fe)); therefore, in terms of As immobilization, the Fe (hydro)oxides on root surface were more important than that in rhizosphere. However, the As content in brown rice did not have significant correlation with the As content on root surface but was significantly correlated (R²?=?0.43, P?<?0.05) with the partition ratio (PR_As?=?IAS_root/IAS_rhizo) of As sequestration on root surface and in rhizosphere, which suggested that Fe (hydro)oxides on root surface did not play the controlling role in lowering As uptake, and the partition ratio PR_As would be a better indicator to evaluate effects of Fe (hydro)oxides around roots on As uptake by rice.

     

Corrosion and stability study of Bacillus thuringiensis var. kurstaki starch industry wastewater-derived biopesticide formulation

Biopesticides are usually sprayed on forests by using planes made up of aluminum alloy. Bioval derived from starch industry wastewater (SIW) in suspension form was developed as stable anticorrosive biopesticide formulation. In this context, various anticorrosion agents such as activated charcoal, glycerin, ethylene glycol, phytic acid, castor oil and potassium silicate were tested as anticorrosive agents. There was no corrosion found in Bioval formulation where potassium silicate (0.5% w/v) was added and compared with Foray 76 B, as an industrial standard, when stored over 6 months. In relation to other parameters, the anticorrosion formulation of Bioval+buffer+KSi reported excellent zeta potential (?33.19 ± 4 mV) and the viscosity (319.13 ± 32 mPa.s) proving it's stability over 6 months, compared to the standard biopesticide Foray 76 B (?36.62 ± 4 mV potential zeta, pH 4.14 ± 0.1 and 206 ± 21 mPa.s viscosity). Metal analysis of the different biopesticides showed that Bioval+buffer+KSi has no corrosion (5.11 ± 0.5 mg kg^?1 of Al and 13.53 ± 1.5 mg kg^?1 of Fe) on the aluminum alloy due to the contribution of sodium acetate buffer at pH 5. The bioassays reported excellent results for Bioval+Buffer+KSi (2.95 ± 0.3 × 10⁹ CFU mL^?1 spores and 26.6 ± 2.7 × 10⁹ IU L^?1 Tx) compared with initial Bioval (2.46 ± 0.3 × 10⁹ CFU mL^?1 spores and 23.09 ± 3 × 10⁹ IU L^?1 Tx) and Foray 76 B (2.3 ± 0.2 × 10⁹ CFU mL^?1 spores and 19.950 ± 2.1 UI L^?1 Tx) which was due to the break-up of the external chitinous membrane due to abrasive action of potassium silicate after ingestion by insects. The contribution of sodium acetate buffer and potassium silicate (0.5% and at pH = 5) as anticorrosion agent in the Bioval allowed production of an efficient biopesticide with a reduced viscosity and favorable pH as compared to Foray 76 B which enhanced the entomotoxic potential against spruce budworm (SB) larvae (Lepidoptera: Choristoneura fumiferana).     

Differential aggregation of polystyrene and titanium dioxide nanoparticles under various salinity conditions and against multiple proteins types

The interaction of nanoplastics (NPls) and engineered nanoparticles (ENPs) with organic matter and environmental pollutants is particularly important. Therefore, their behavior should be investigated under the different salinity conditions, mimicking rivers and coastal environments, to understand this phenomenon in those areas. In this work, we analyzed the elementary characteristics of polystyrene-PS (unmodified surface and modified with amino or carboxyl groups) and titanium dioxide-TiO2 nanoparticles. The effect of salinity on their colloidal properties was studied too. Also, the interaction with different types of proteins (bovine serum albumin-BSA and tilapia proteins), as well as the formation of the BSA corona and its effect on the colloidal stability of nanoparticles, were evaluated. The morphology and dispersion of sizes were more uniform in unmodified-surface PS-NPs (70.5?±?13.7 nm) than in TiO2-NPs (131.2?±?125.6 nm). Likewise, Rama spectroscopy allowed recognizing peaks associated with the PS phenyl group aromatic ring in unmodified-surface PS-NPs (621, 1002, 1582, and 1602 cm^?1). For TiO2-NPs, the data suggest belonging to the tetragonal form, also known as rutile (445, 610 cm^?1). The elevation of salinity dose-dependently decreased NP colloid stability, with more significant variation in the PS-NPs compared to TiO2-NPs. The organic matter is also involved in this phenomenon, differentially as a function of time compared to its absence (unmodified-surface PS-NPs 30 psu/TOC 5 mgL^?1/24 h: 2876.6?±?378.03 nm; unmodified-surface PS-NPs 30 psu/24 h: 2133?±?49.57 nm). In general, the TiO2-NPs demonstrated greater affinity with all proteins tested (0.066 g/L). It was observed that morphology, size, and surface chemical modification intervene in a relevant way in the interaction of the nanoparticles with bovine serum albumin (unmodified-surface PS-NPs 298 K: 6.08E⁺⁰²; 310 K: 6.63E⁺⁰²; TiO2-NPs 298 K: 8.76E⁺⁰²; 310 K: 1.05E⁺⁰³ L mol^?1) and tilapia tissues proteins (from blood, gills, liver, and brain). Their morphology and size also determined the protein corona formation and the NPs’ agglomeration. These findings can provide references during knowledge transfer between NPls and ENPs.