Assessment of variations in atmospheric PCDD/Fs by Asian dust in Southeastern Korea

Atmospheric concentrations of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) were measured in southeastern Korea during the spring of 2002. During this period, severe Asian dust events (ADs) occurred throughout Korea. Total suspended particulates (TSP) of ADs (456.8 μg m⁻³) increased approximately 3.6-fold compared with non-Asian dust events (NADs; 128.5 μg m⁻³). However, the concentrations of PCDD/Fs (average concentration, 3.34 pg m⁻³) did not increase as much as TSP; there was not a significant difference in the concentrations of particle-bound PCDD/Fs collected between ADs (2.45 pg m⁻³) and NADs (2.05 pg m⁻³). Meanwhile, according to TSP levels, the concentrations during NADs were 2.8-fold higher than ADs (16.73 and 5.98 ng g⁻¹-TSP, respectively). High TSP levels during sand storms without an increase in PCDD/Fs reflected an increase in coarse and accumulation mode particles. Gas/particle partitioning studies revealed the additional inputs of particulate matters to the air during ADs which did not relate with the increase of PCDD/Fs. Furthermore, emissions from ADs may consist of relatively complex atmospheric particles; back trajectories showed air masses moving at low altitudes over Korea, but there were no differences in PCDD/Fs or atmospheric pollutants regardless of air movements. The study area, which is located in southeastern Korea, might be affected by both marine and regional anthropogenic sources, which do not appear to cause clear differences in PCDD/F concentrations or congener profiles between different air trajectories.     

Atmospheric distribution of polycyclic aromatic hydrocarbons and deposition to Galveston Bay,Texas, USA

Estimates of the atmospheric deposition to Galveston Bay of polycyclic aromatic hydrocarbons (PAHs) are made using precipitation and meteorological data that were collected continuously from 2 February 1995 to 6 August 1996 at Seabrook, TX, USA. Particulate and vapor phase PAHs in ambient air and particulate and dissolved phases in rain samples were collected and analyzed. More than 95% of atmospheric PAHs were in the vapor phase and about 73% of PAHs in the rain were in the dissolved phase. Phenanthrene and napthalene were the dominant compounds in air vapor and rain dissolved phases, respectively, while 5 and 6 ring PAH were predominant in the particulate phase of both air and rain samples. Total PAH concentrations ranged from 4 to 161 ng m⁻³ in air samples and from 50 to 312 ng l⁻¹ in rain samples. Temporal variability in total PAH air concentrations were observed, with lower concentrations in the spring and fall (4–34 ng m ⁻³) compared to the summer and winter (37–161 ng m⁻³). PAHs in the air near Galveston Bay are derived from both combustion and petroleum vaporization. Gas exchange from the atmosphere to the surface water is estimated to be the major deposition process for PAHs (1211 μg m^{− 2} yr^{− 1}), relative to wet deposition (130 μg m⁻² yr^{− 1}) and dry deposition (99 μg m⁻² yr^{− 1}). Annual deposition of PAHs directly to Galveston Bay from the atmosphere is estimated as 2  t yr⁻¹.     

Atmospheric deposition of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) in Guangzhou,China

Atmospheric deposition of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) was investigated at four locations, namely at Yuancun, Wushan, Haizhu and Changban in Guangzhou City, Guangdong Province. The annual deposition fluxes of tetra- to octa-CDD/Fs (total PCDD/Fs) were found to range from 170 to 3000 (mean 1500) pg m⁻² day⁻¹, and the fluxes of total 2, 3, 7, 8-substituted PCDD/F congeners ranged from 2.1 to 41 (mean 20) pg WHO-TEQ m⁻² day⁻¹ at Wushan. The average deposition fluxes of total 2, 3, 7, 8-substituted PCDD/F congeners in rainy season were found to be 37, 27 and 28 pg WHO-TEQ m⁻² day⁻¹ at Yuancun, Haizhu and Changban, respectively, and the PCDD/F deposition fluxes behaved obviously higher in rainy season than in dry season. Results from regression analysis showed that number of rainy days, the amount of wet precipitation, PCDD/F concentrations in particles and organic carbon content played important roles in the variation of PCDD/F deposition fluxes. Monthly average temperatures change little over the year. Therefore, it only played a minor role in monthly variation of PCDD/F deposition fluxes. Particle deposition fluxes were generally not considered as the factor that could cause the differences in PCDD/F deposition fluxes between rainy and dry season, but were found to be related with PCDD/F deposition fluxes in rainy season or dry season. It was found that the profiles of PCDD/F homologs or congeners in the samples were the same either spatially or temporally, indicating that the PCDD/F emission sources were similar to one another. The similarities in PCDD/F homolog patterns and the differences in deposition fluxes between samples collected from heavy-traffic roadside and nearby residence house roof indicated that vehicle exhaust might be an important source for PCDD/F in Guangzhou. PCDD/F concentrations and profiles of PCDD/F homologs in atmospheric deposition were compared with those in both total suspended particles in air and soils, and conclusions indicated that atmospheric deposition possibly tended to remove lower-chlorinated DD/Fs from air and was one of sources for PCDD/Fs in soils.     

A novel field measurement method for determining fine particle and gas emissions from residential wood combustion

Emission data from residential wood combustion are usually obtained on test stands in the laboratory but these measurements do not correspond to the operational conditions in the field because of the technological boundary conditions (e.g. testing protocol, environmental and draught conditions). The field measurements take into account the habitual practice of the operators and provide the more reliable results needed for emission inventories. In this study, a workable and compact method for measuring emissions from residential wood combustion in winter conditions was developed. The emissions for fine particle, gaseous and PAH compounds as well as particle composition in real operational conditions were measured from seven different appliances. The measurement technique worked well and was evidently suitable for winter conditions. It was easy and fast to use, and no construction scaffold was needed. The dilution of the sample with the combination of a porous tube diluter and an ejector diluter was well suited to field measurement. The results indicate that the emissions of total volatile organic carbon (TVOC) (17 g kg⁻¹ (of dry wood burned)), carbon monoxide (CO) (120 g kg⁻¹) and fine particle mass (PM₁) (2.7 g kg⁻¹) from the sauna stove were higher than in the other measured appliances. In the masonry heaters, baking oven and stove, the emissions were 2.9–9 g kg⁻¹ TVOC, 28–68 g kg⁻¹ CO and 0.6–1.6 g kg⁻¹ PM₁. The emission of 12 PAHs (PAH₁₂) from the sauna stove was 164 mg kg⁻¹ and consisted mainly of PAHs with four benzene rings in their structure. PAH₁₂ emission from other appliances was, on average, 21 mg kg⁻¹ and was dominated by 2-ring PAHs. These results indicate that despite the non-optimal operational practices in the field, the emissions did not differ markedly from the laboratory measurements.     

Ambient air quality of two metropolitan cities of Pakistan and its health implications

The present study reports findings on TSP loading in the ambient air of two major cities in Pakistan – Karachi and Islamabad. Data for TSP were collected at one site in Karachi and two in Islamabad between 10 December 1998 and 08 January 1999. This article reports one of the highest TSP loadings recorded so far in any megacity of the world. During the study period, average daily TSP concentrations at the Karachi site ranged from 627 to 938 μg m⁻³ with a mean of 668 μg m⁻³. On four occasions TSP concentrations were >1000 μg m⁻³ (range 1031–1736 μg m⁻³). At the Islamabad sampling site in close proximity to the city's industrial sector, daily TSP concentrations varied in the range of 428–998 μg m⁻³ (mean 691 μg m⁻³). Even at a relatively remote site of the city (Saidpur), TSP loading was high (range 145–448 μg m⁻³; mean 275 μg m⁻³). By virtue of the WHO definition, the 24-h average TSP concentrations in a busy commercial site in Karachi and in the vicinity of an industrial sector in Islamabad were in “exceedance” by a factor of 4–8. At Saidpur, the remote site, the 24-h average TSP loading exceeded the WHO guideline of 120 μg m⁻³ by a factor of 1.2–3.7.     

A national inventory to estimate release of polychlorinated dibenzo-p-dioxins and dibenzofurans in Portugal

Taking into account current environmental concerns, the main objective of this work focused a national inventory aiming to estimate the amount of polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans (PCDD/PCDF) released in Portugal in 2006. The methodology used was based on the Standardized Toolkit for Identification and Quantification of Dioxins and Furan Releases, developed by UNEP Chemicals, in 2005. The method allows the assessment of the amount of PCDD/PCDF released into the environment along five vectors involving air, water, land, products and residues. Facing some difficulties mainly regarding to the availability of data for some activities known to produce PCDD/PCDF, three scenarios (Sc1 to Sc3) corresponding to lower, central and upper estimates were established. The Sc1 scenario (lower estimate) includes the situations where in case of doubt or scarce information, reduced or none emission values were assumed, Sc2 refers to a central estimate, which is believed to be the most realistic for the Portuguese situation, while Sc3 corresponds to the worst case (upper estimate). The results obtained pointed out that the total amount of PCDD/PCDF emitted in Portugal during the period under analysis was in the range of 51.2–217.9 g TEQ year⁻¹, with the most likely value of 95.2 g TEQ year⁻¹ achieved under the Sc2 scenario. This study also showed that the methodology developed by UNEP Chemicals is a very simple one, and the main difficulty is the availability of data. The main indicators calculated in this study were 8.98 μg TEQ/(year person) by taking into account the total amount of PCDD/PCDF released, and 3.63 μg TEQ/(year person) when only air emissions were considered.     

Production and removal of aerosol in a polluted fog layer: model evaluation and fog effect on PM

A radiation fog physics, gas- and aqueous-phase chemistry model is evaluated against measurements in three sites in the San Joaquin Valley of California (SJV) during the winter of 1995. The measurements include for the first time vertically resolved fog chemical composition measurements. Overall the model is successful in reproducing the fog dynamics as well as the temporal and spatial variability of the fog composition (pH, sulfate, nitrate, and ammonium concentrations) in the area. Sulfate production in the fog layer is relatively slow (1–4 μg m⁻³ per fog episode) compared to the episodes in the early 1980s because of the low SO₂ concentrations in the area and the lack of oxidants inside the fog layer. Sulfate production inside the fog layer is limited by the availability of oxidants in the urban areas of the valley and by SO₂ in the more remote areas. Nitrate is produced in the rural areas of the valley by the heterogeneous reaction of N₂O₅ on fog droplets, but this reaction is of secondary importance for the more polluted urban areas. The gas-phase production of HNO₃ during the daytime is sufficient to balance the nitrate removed during the nighttime fog episodes. Entrainment of air from the layer above the fog provides another source of reactants for the fog layer. Wet removal is one of most important processes inside the fog layer in SJV. We estimate based on the three episodes investigated during IMS95 that a typical fog episode removes 500–2000 μg m⁻² of sulfate, 2500–6500 μg m⁻² of nitrate, and 2000–3500 μg m⁻² of ammonium. For the winter SJV valley the net fog effect corresponds to reductions in ground ambient concentrations of 0.05–0.2 μg m⁻³ for sulfate, 3–6 μg m⁻³ for total nitrate, and 1–3 μg m⁻³ for total ammonium.     

Composition and emissions of VOCs in main- and side-stream smoke of research cigarettes

It is well known that mainstream (MS) and sidestream (SS) cigarette smoke contains a vast number of chemical substances. Previous studies have emphasized SS smoke rather than MS smoke to which smokers are exposed, and most have used chamber tests that have several disadvantages such as wall losses. Emissions from standard research cigarettes have been measured, but relatively few constituents have been reported, and only the 1R4F (low nicotine) cigarette type has been tested. This study provides a comprehensive characterization of total, MS and SS smoke emissions for the 1R5F (ultra low nicotine), 2R4F (low nicotine), and 1R3F (standard nicotine) research cigarettes research cigarettes, including emission factors for a number of toxic compounds (e.g., benzene) and tobacco smoke tracers (e.g., 2,5-dimethyl furan). Emissions of volatile organic compounds (VOCs) and particulate matter (PM) are quantified using a dynamic dilution emission measurement system that is shown to produce accurate, rapid and reproducible results for over 30 VOCs and PM. SS and MS emissions were accurately apportioned based on a mass balance of total emissions. As expected, SS emissions greatly exceeded MS emissions. The ultra low nicotine cigarette had lower emissions of most VOCs compared to low and standard nicotine cigarettes, which had similar emissions. Across the three types of cigarettes, emissions of benzene (296–535 μg cig⁻¹), toluene (541–1003 μg cig⁻¹), styrene (90–162 μg cig⁻¹), 2-dimethyl furan (71–244 μg cig⁻¹), naphthalene (15–18 μg cig⁻¹) and other VOCs were generally comparable to or somewhat higher than literature estimates using chamber tests.     

Measurement and analysis of atmospheric ammonia emissions from anaerobic lagoons

Ammonia-nitrogen flux (NH₃-N=(14/17)NH₃) was determined from six anaerobic swine waste storage and treatment lagoons (primary, secondary, and tertiary) using the dynamic chamber system. Measurements occurred during the fall of 1998 through the early spring of 1999, and each lagoon was examined for approximately one week. Analysis of flux variation was made with respect to lagoon surface water temperature (∼15 cm below the surface), lagoon water pH, total aqueous phase NH_x(=NH₃+NH₄⁺) concentration, and total Kjeldahl nitrogen (TKN). Average lagoon temperatures (across all six lagoons) ranged from approximately 10.3 to 23.3^°C. The pH ranged in value from 6.8 to 8.1. Aqueous NH_x concentration ranged from 37 to 909 mg N l⁻¹, and TKN varied from 87 to 950 mg N l⁻¹. Fluxes were the largest at the primary lagoon in Kenansville, NC (March 1999) with an average value of 120.3 μg N m⁻² min⁻¹, and smallest at the tertiary lagoon in Rocky Mount, NC (November 1998) at 40.7 μg N m⁻² min⁻¹. Emission rates were found to be correlated with both surface lagoon water temperature and aqueous NH_x concentration. The NH₃-N flux may be modeled as ln(NH₃-N flux)=1.0788+0.0406T_L+0.0015([NH_x]) (R²=0.74), where NH₃-N flux is the ammonia flux from the lagoon surface in μg N m⁻² min⁻¹, T_L is the lagoon surface water temperature in ^°C, and [NH_x] is the total ammonia-nitrogen concentration in mg N l⁻¹.     

Concentration-dependent NH3 deposition processes for moorland plant species with and without stomata

Currently, in operational modelling of NH₃ deposition a fixed value of canopy resistance (R_c) is generally applied, irrespective of the plant species and NH₃ concentration. This study determined the effect of NH₃ concentration on deposition processes to individual moorland species. An innovative flux chamber system was used to provide accurate continuous measurements of NH₃ deposition to Deschampsia cespitosa (L.) Beauv., Calluna vulgaris (L.) Hull, Eriophorum vaginatum L., Cladonia spp., Sphagnum spp., and Pleurozium schreberi (Brid.) Mitt. Measurements were conducted across a wide range of NH₃ concentrations (1–140 μg m⁻³).NH₃ concentration directly affects the deposition processes to the vegetation canopy, with R_c, and cuticular resistance (R_w) increasing with increasing NH₃ concentration, for all the species and vegetation communities tested. For example, the R_c for C. vulgaris increased from 14 s m⁻¹ at 2 μg m⁻³ to 112 s m⁻¹ at 80 μg m⁻³. Diurnal variations in NH₃ uptake were observed for higher plants, due to stomatal uptake; however, no diurnal variations were shown for non-stomatal plants. R_c for C. vulgaris at 80 μg m⁻³ was 66 and 112 s m⁻¹ during day and night, respectively. Differences were found in NH₃ deposition between plant species and vegetation communities: Sphagnum had the lowest R_c (3 s m⁻¹ at 2 μg m⁻³ to 23 at 80 μg m⁻³), and D. cespitosa had the highest nighttime value (18 s m⁻¹ at 2 μg m⁻³ to 197 s m⁻¹ at 80 μg m⁻³).     

Occurrence of antibiotics in water,sediments, aquatic plants,and animals from Baiyangdian Lake in North China

This study investigated the presence and distribution of 22 antibiotics, including eight quinolones, nine sulfonamides and five macrolides, in the water, sediments, and biota samples from Baiyangdian Lake, China. A total of 132 samples were collected in 2008 and 2010, and laboratory analyses revealed that antibiotics were widely distributed in the lake. Sulfonamides were the dominant antibiotics in the water (0.86–1563 ng L⁻¹), while quinolones were prominent in sediments (65.5–1166 μg kg⁻¹) and aquatic plants (8.37–6532 μg kg⁻¹). Quinolones (17.8–167 μg kg⁻¹) and macrolides [from below detection limit (BDL) to 182 μg kg⁻¹] were often found in aquatic animals and birds. Salvinia natans exhibited the highest bioaccumulation capability for quinolones among three species of aquatic plants. Geographical differences of antibiotic concentrations were greatly due to anthropogenic activities. Sewage discharged from Baoding City was likely the main source of antibiotics in the lake. Risk assessment of antibiotics on aquatic organisms suggested that algae and aquatic plants might be at risk in surface water, while animals were likely not at risk.     

Nitric acid and the origin and size segregation of aerosol nitrate aloft during BRACE 2002

As part of the BRACE 2002 May field intensive, the NOAA Twin Otter flew 21 missions over terrestrial, marine, and mixed terrestrial and marine sites in the greater Tampa, Florida, airshed including over Tampa Bay and the Gulf of Mexico. Aerosols were collected with filter packs and their inorganic fractions analyzed post hoc with ion chromatography. Anion mass dominated both the fine- (particle diameters ⩽2.5 μm) and coarse-mode (particle diameters 10.0–2.5 μm) inorganic fractions: SO₄²⁻in the fine fraction, 3.7 μg m⁻³ on average and Cl⁻ and NO₃⁻ in the coarse fraction, 0.6 μg m⁻³ on average and 1.4 μg m⁻³ on average, respectively. Ammonium ion dominated the inorganic fine-mode cation mass, averaging 1.2 μg m⁻³, presumably in association with SO₄². Coarse-mode cation mass was dominated by Na⁺, but the concentrations of Ca²⁺ and K⁺ together often equaled or exceeded the Na⁺ mass which was, on average, 0.6 μg m⁻³. Nitrate appeared predominantly in the coarse rather than the fine fraction, as expected, and the fine fraction never contributed >15% of the total NO₃ concentration. Nitric acid dominated the NO₃⁻ contribution from both aerosol size fractions, and constituted at least 45% of the total NO₃ in all samples. Coarse-mode Cl⁻ depletion, and hence NO₃⁻ replacement, reached 100% within the first 4 h of plume travel from the urban core in some samples, although it was most often less than 100% and slightly below the expected 1:1 ratio with coarse-mode NO₃⁻ concentration: the slope of the regression line of NO₃⁻ concentration to Cl⁻ depletion was 0.9 in the coarse fraction. In addition, terrestrial samples were markedly lower in Cl⁻ depletion, and thus in substituted NO₃^–, than were marine and mixed samples: 15–25% depletion in terrestrial samples vs. 50–65% in marine samples with the same air mass age. Thus, we conclude that NO₃⁻ and its progenitor compound HNO₃ were present in the Tampa airshed in insufficient amounts to titrate fully the slightly alkaline coarse-mode particles there, and to replace completely the Cl⁻ from the coarse-mode NaCl.     

Measuring chemical emissions using open-path Fourier transform infrared (OP-FTIR) spectroscopy and computer-assisted tomography

This paper reports on a field study that was part of a large-scale, multi-seasonal research study with the North Carolina Department of Environment, Health, and Natural Resources, to measure nitrogen emissions from an intensive swine confinement facility. The study measured emission rates using tracer gases and a horizontal network of open-path Fourier transform infrared (FTIR) optical rays placed less than a meter above the surface of an approximately 6 acre intensive swine waste lagoon in Eastern North Carolina. This network of rays simultaneously monitored the ammonia and the tracer gases every 2 min. The open-path measurements were combined with the mathematical mapping techniques of computer-assisted tomography (CAT) to create two-dimensional concentration maps of the gases for the entire lagoon surface. For this study, a ratioing technique was applied to the tomographic concentration maps to estimate the nitrogen emission rates (from ammonia) using known tracer emission rates. The average concentrations of ammonia measured in August, November, and May were 0.81, 0.25, and 0.74 ppm, respectively. In general, ammonia concentrations were lowest at the center of the lagoon and could vary across a lagoon from 2 to 4 times depending upon the time of the day and the meteorological conditions. Emission rates were only calculated for November and May, up until midnight. In November 1997, the average flux was 1910 μg N m⁻²-min⁻¹ (range 542–4695 μg N m⁻²-min⁻¹) and in May the average flux was 4775 μg N m⁻²-min⁻¹ (range 2572–8499 μg N m⁻²-min⁻¹). This study was important because it not only provided nitrogen emission rate measurements using a new technology which can measure concentrations over large areas in real time, it was the first large-scale outdoor field study using this application.     

Emission of polycyclic aromatic hydrocarbons from gasohol and ethanol vehicles

The exhaust emission of the polycyclic aromatic hydrocarbons (PAHs) considered toxic to human health were investigated on two spark ignition light duty vehicles, one being gasohol (Gasohol, in Brazil, is the generic denomination for mixtures of pure gasoline plus 20–25% of anhydrous ethyl alcohol fuel (AEAF).)-fuelled and the other a flexible-fuel vehicle fuelled with hydrated ethanol. The influence of fuel type and quality, aged lubricant oil type and use of fuel additives on the formation of these compounds was tested using standardized tests identical to US FTP-75 cycle. PAH sampling and chemical analysis followed the basic recommendations of method TO-13 (United States. Environmental Protection Agency, 1999. Compendium Method TO-13A – Determination of polycyclic Aromatic hydrocarbons (PAH) in Ambient Air Using Gas Chromatography/Mass Spectrometry (CG/MS). Center for environmental research information, Cincinnati, p. 78), with the necessary modification for this particular application.Results showed that the total PAH emission factor varied from 41.9 μg km^?1 to 612 μg km^?1 in the gasohol vehicle, and from 11.7 μg km^?1 to 27.4 μg km^?1 in the ethanol-fuelled vehicle, a significant difference in favor of the ethanol vehicle. Generally, emission of light molecular weight PAHs was predominant, while high molecular weights PAHs were not detected. In terms of benzo(a)pyrene toxicity equivalence, emission factors varied from 0.00984 μg TEQ km^?1 to 4.61 μg TEQ km^?1 for the gasohol vehicle and from 0.0117 μg TEQ km^?1 to 0.0218 μg TEQ km^?1 in the ethanol vehicle.For the gasohol vehicle, results showed that the use of fuel additive causes a significant increase in the emission of naphthalene and phenanthrene at a confidence level of 90% or higher; the use of rubber solvent on gasohol showed a reduction in the emission of naphthalene and phenanthrene at the same confidence level; the use of synthetic oil instead of mineral oil also contributed significantly to a decrease in the emission of naphthalene and fluorene. In relation to the ethanol vehicle, the same factors were tested and showed no statistically significant influence on PAH emission.     

Effects of biodiesel on emissions of regulated air pollutants and polycyclic aromatic hydrocarbons under engine durability testing

An 80,000-km durability test was performed on two engines using diesel and biodiesel (methyl ester of waste cooking oil) as fuel in order to examine emissions resulting from the use of biodiesel. The test biodiesel (B20) was blended with 80% diesel and 20% methyl ester derived from waste cooking oil. Emissions of regulated air pollutants, including CO, HC, NO_x, particulate matter (PM) and polycyclic aromatic hydrocarbons (PAHs) were measured at 20,000-km intervals. The identical-model engines were installed on a standard dynamometer equipped with a dilution tunnel used to measure the pollutants. To simulate real-world driving conditions, emission measurements were made in accordance with the United States Environmental Protection Agency (USEPA) FTP transient cycle guidelines. At 0 km of the durability test, HC, CO and PM emission levels were lower for the B20 engine than those for diesel. After running for 20,000 km and longer, they were higher. However, the deterioration coefficients for these regulated air pollutants were not statistically higher than 1.0, implying that the emission factors do not increase significantly after 80,000 km of driving. Total (gaseous+particulate phase) PAH emission levels for both B20 and diesel decreased as the driving mileage accumulated. However, for the engine using B20 fuel, particulate PAH emissions increased as engine mileage increased. The average total PAH emission factors were 1097 and 1437 μg bhp h⁻¹ for B20 and diesel, respectively. For B20, the benzo[a]pyrene equivalence emission factors were 0.77, 0.24, 0.20, 7.48, 5.43 and 14.1 μg bhp h⁻¹ for 2-, 3-, 4-, 5-, 6-ringed and total PAHs. Results show that B20 use can reduce both PAH emission and its corresponding carcinogenic potency.     

Concentration-dependent NH3 deposition processes for mixed moorland semi-natural vegetation

Dry deposition modelling typically assumes that canopy resistance (R_c) is independent of ammonia (NH₃) concentration. An innovative flux chamber system was used to provide accurate continuous measurements of NH₃ deposition to a moorland composed of a mixture of Calluna vulgaris (L.) Hull, Eriophorum vaginatum L. and Sphagnum spp. Ammonia was applied at a wide range of concentrations (1–100 μg m⁻³). The physical and environmental properties and the testing of the chamber are described, as well as results for the moorland vegetation using the ‘canopy resistance’ and ‘canopy compensation point’ interpretations of the data.Results for moorland plant species demonstrate that NH₃ concentration directly affects the rate of NH₃ deposition to the vegetation canopy, with R_c and cuticular resistance (R_w) increasing with increasing NH₃ concentrations. Differences in R_c were found between night and day: during the night R_c increases from 17 s m⁻¹ at 10 μg m⁻³ to 95 s m⁻¹ at 80 μg m⁻³, whereas during the day R_c increases from 17 s m⁻¹ at 10 μg m⁻³ to 48 s m⁻¹ at 80 μg m⁻³. The lower resistance during the day is caused by the stomata being open and available as a deposition route to the plant. R_w increased with increasing NH₃ concentrations and was not significantly different between day and night (at 80 μg m⁻³ NH₃ day R_w=88 s m⁻¹ and night R_w=95 s m⁻¹). The results demonstrate that assessments using fixed R_c will over-estimate NH₃ deposition at high concentrations (over ∼15 μg m⁻³).     

Characteristics of carbonyl compounds in public vehicles of Beijing city: Concentrations,sources, and personal exposures

The characteristics of carbonyl compounds (carbonyls) including concentrations, major sources, and personal exposure were investigated for 29 vehicles including taxi, bus and subway in Beijing. It was found that the taxis (Xiali, TA) and buses (Huanghe, BA) fueled by gasoline with longer service years had the higher indoor carbonyl levels (178±42.7 and 188±31.6 μg m⁻³) while subways energized by electricity without exhaust and the jingwa buses (BB) driven in the suburb had the lower levels with total concentrations of 98.5±26.3 and 92.1±20.3 μg m⁻³, respectively. Outdoor carbonyls of taxi cars and buses were nearly at the same level with their total concentrations varying from 80 to 110 μg m⁻³. The level of outdoor subways carbonyls was equal with the ambient air levels. Exhaust leakage, indoor material emissions, photochemical formation, and infiltration of outdoor air were considered to be the major sources to in-vehicle carbonyls. Personal exposures and cancer risk to formaldehyde and acetaldehyde were calculated for professional bus and taxi drivers, respectively. Taxi drivers had the highest cancer risk with personal exposure to formaldehyde and acetaldehyde of 212 and 243 μg day⁻¹, respectively. The public concern should pay considerable attention to professional drivers’ health.     

Comprehensive assessment of pine needles as bioindicators of PAHs using multivariate analysis. The importance of temporal trends

The importance of the annual and seasonal trends associated to the polycyclic aromatic hydrocarbons (PAHs) biomonitoring by pine needles are studied with a comprehensive use of univariate and multivariate analysis tools. For this purpose, four pine needle sampling campaigns (winter, spring, summer and autumn 2007) were carried out in 29 sites from Portugal. Needles from Pinus pinaster Ait. and Pinus pinea L. trees were collected from all year-classes available in each tree, corresponding to the different shoots of needles coming out every spring and the results of both species were treated separately. Annual trends of polycyclic aromatic hydrocarbons (PAHs) contamination indicate a general increase from the least to the most exposed year-classes, for all seasons. The mean values for the sum of 16 PAHs ranged from 71 ± 33 ng g⁻¹ (dry weight – dw) for new year (2007) needles in the summer to 514 ± 317 ng g⁻¹ (dw) for 2-year needles (2005) in the spring for P. pinea, and between 90 ± 50 ng g⁻¹ (dw) for new year (2007) needles in the summer and 1212 ± 436 ng g⁻¹ (dw) for 3-year needles (2004) in summer for P. pinaster. The seasonal evolution shows the highest concentrations in the winter, then declining to the lowest levels in the summer and rising again from summer to autumn. Principal component analysis confirmed differences between seasons and needle year-classes, more visible for P. pinea samples. The cooler seasons have more affinity towards the lighter more abundant PAHs, as do the older needles. Differences between both pine species are also evident.     

Aerosol scattering properties in northern China

The aerosol scattering properties were investigated at two continental sites in northern China in 2004. Aerosol light scattering coefficient (σ_sp) at 525 nm, PM₁₀, and aerosol mass scattering efficiencies (α) at Dunhuang had a mean value of 165.1±148.8 M m⁻¹, 157.6±270.0 μg m⁻³, and 2.30±3.41 m² g⁻¹, respectively, while these values at Dongsheng were, respectively, 180.2±151.9 M m⁻¹, 119.0±112.9 μg m⁻³, and 1.87±1.41 m² g⁻¹. There existed a seasonal variability of aerosol scattering properties. In spring, at Dunhuang PM₁₀, σ_sp, and α were 184.1±211.548 μg m⁻³, 126.3±89.6 M m⁻¹, and 1.05±0.97 m² g⁻¹, respectively, and these values at Dongsheng were 146.4±142.1 μg m⁻³, 183.4±81.7 M m⁻¹, and 1.98±1.52 m² g⁻¹, respectively. However, in winter at Dunhuang PM₁₀, σ_sp, and α were 158.1±261.4 μg m⁻³, 303.3±165.2 M m⁻¹, and 3.17±1.93 m² g⁻¹, respectively, and these values at Dongsheng were 155.7±170.1 μg m⁻³, 304.4±158.1 M m⁻¹, and 2.90±1.72 m² g⁻¹, respectively. σ_sp and α in winter were higher than that in spring at both the sites, which coincides with the characteristics of dust aerosol and pollution aerosol. Overall, the dominant aerosol types in spring and winter at both sites in northern China are dust aerosol and pollution aerosol, respectively.