Influence of vacuum degree on the effect of gas explosion suppression by vacuum chamber

In order to study the influence of vacuum degree on gas explosion suppression by vacuum chamber, this study used the 0.2 mm thick polytetrafluoroethylene film as the diaphragm of vacuum chamber to carry out a series of experiments of gas explosion suppression by vacuum chamber with the vacuum degree from −0.01 MPa to −0.08 MPa. The experimental results show that: under the condition of any vacuum degree, vacuum chamber can effectively suppress the explosion flame and overpressure; as vacuum degree changes, the effect of gas explosion suppression using vacuum chamber is slightly different. Vacuum chamber has obvious influence on propagation characteristics of the explosion flame. After explosion flame passes by vacuum chamber, the flame signal weakens, the flame thickness becomes thicker, and the flame speed slows down. With the increase of the vacuum degree of vacuum chamber, the flame speed can be prevented from rising early by vacuum chamber. The higher the vacuum degree is, the more obviously the vacuum chamber attenuates the explosion overpressure, the smaller the average overpressure is, and the better effect of the gas explosion suppression is. Vacuum chamber can effectively weaken the explosion impulse under each vacuum degree. From the beginning of −0.01 MPa, the vacuum chamber can gradually weaken explosion impulse as the vacuum degree increases, and the effect of gas explosion suppression gradually becomes better. When the vacuum degree is greater than −0.04 MPa, the increase of vacuum degree can make the explosion overpressure decrease but have little influence on the explosion impulse. Therefore, the vacuum chamber has the preferable suppression effect with equal to or greater than −0.04 MPa vacuum degree.     

含弱约束端面直角管道汽油蒸气爆炸及七氟丙烷抑爆研究*

为研究七氟丙烷对汽油蒸气爆炸抑制作用,搭建含弱约束端面直角管道汽油蒸气爆炸抑制实验系统,开展汽油蒸气爆炸实验研究,并与喷入七氟丙烷抑爆介质进行对比,分析爆炸超压值、火焰强度值和火焰传播速度等爆炸特性参数变化情况。结果表明:在1.3%,1.5%和1.7%汽油蒸气体积分数下,不加抑爆介质时,爆炸超压值、火焰强度和火焰传播速度随着汽油蒸气体积分数的升高而增大;将七氟丙烷作为抑爆介质喷入时,爆炸超压峰值分别下降91.06%,34.57%和50.92%,火焰强度降幅达到99.83%,火焰传播速度几乎降为0,火焰持续时间随之缩短几乎为0,七氟丙烷具有良好的阻隔防爆效果。     

Experimental and numerical investigation of constant volume dust and gas explosions in a 3.6-m flame acceleration tube

This paper describes an experimental investigation of turbulent flame propagation in propane-air mixtures, and in mechanical suspensions of maize starch dispersed in air, in a closed vessel of length 3.6 m and internal cross-section 0.27 m × 0.27 m. The primary motivation for the work is to gain improved understanding of turbulent flame propagation in dust clouds, with a view to develop improved models and methods for assessing explosion risks in the process and mining industries. The study includes computational fluid dynamics (CFD) simulations with FLACS and DESC, for gas and dust explosions respectively. For initially quiescent propane-air mixtures, FLACS over-predicts the rate of combustion for fuel-lean mixtures, and under-predicts for fuel-rich mixtures. The simulations tend to be in better agreement with the experimental results for initially turbulent gaseous mixtures. The experimental results for maize starch vary significantly between repeated tests, but the subset of tests that yields the highest explosion pressures are in reasonable agreement with CFD simulations with DESC.     

The effect of orifice plates with different shapes on explosion propagation of premixed methane–air in a semi-confined pipeline

The effect of internal shape of obstacles on the deflagration of premixed methane–air (concentration of 10%) was experimentally investigated in a semi-confined steel pipeline (with a square cross section size of 80 mm × 80 mm and 4 m long). The obstacles used in this study were circular, square, triangular and gear-shaped (4-teeth, 6-teeth and 8-teeth) orifice plates with a blockage ratio of 75%, and the perimeter of the orifice was regarded as a criterion for determining the sharpness of the orifice plate. The overpressure history, flame intensity histories, flame front propagation speed, maximum flame intensity and peak explosion overpressure were analyzed. The explosion in the pipeline can be divided into two stages: initial explosion and secondary explosion. The secondary explosion is caused by recoiled flame. The perimeter is positively related to the intensity of the recoiled flame and the ability of orifice plate to suppress the explosion propagation. In addition, the increase in the perimeter will cause the acceleration of the flame passing through the orifice plate, while after the perimeter of the orifice reaches a certain value, the effect of the increase in perimeter on explosion excitation becomes no obvious. The overpressure (static pressure) downstream of the orifice plate is the result of the combined effect of explosion intensity and turbulence. The increase in perimeter leads to the increase in turbulence downstream of the orifice plate which in turn causes more explosion pressure to be converted into dynamic pressure.     

Experimental study on explosion characteristics of ethanol-gasoline blended fuels

In the present work, a series of experiments have been performed to analyze the explosion characteristics of ethanol-gasoline with various blended ratios (0%, 5%, 10%, 15%, 30%, 50%, 70%, 80%, and 100%). A vented rectangular vessel with a cross-section of 100 mm × 100 mm, 600 mm long and a 40 mm diameter vent on the top is used to carry out the experiments. The flame propagation is recorded by a phantom high-speed camera with 5000 fps, while the histories of the explosion overpressure are measured by two PCB pressure sensors and the explosion sound pressure level is obtained by a CRY sound sensor. The results indicate that the maximum overpressure and flame propagation speed increases linearly as the blended ratio increases when the initial volume of blended fuel is 1.0 mL; While the change of explosion overpressure and flame propagation speed shows a trend of decreasing at first and then increasing as the concentration increases to 1.8 mL. It is also found that the peak of the sound pressure level exceeds 100 dB under all tests, which would damage the human's hearing. What's more, relationships between explosion overpressure and sound pressure level are examined, and the change of the maximum overpressure can be reflected to some extent by the measurement of the maximum sound pressure level. The study is significant to reveal the essential characteristic of the explosion venting process of ethanol-gasoline under different initial blended ratios, and the results would help deepen the understanding of ethanol-gasoline blended fuels explosion and the assessment of the explosion hazardous.     

Effects of cross-wise obstacle position on methane–air deflagration characteristics

A vented chamber, with internal dimensions of 150 mm × 150 mm × 500 mm, is constructed in which the premixed methane–air deflagration flame, propagating away from the ignition source, interacts with obstacles along its path. Three obstacle configurations with different cross-wise positions are investigated. The cross-wise obstacle positions are found to have significant effects on deflagration characteristics, such as flame structure, flame front location, flame speed, and overpressure transients. The rate of flame acceleration, as the flame passes over the last obstacle, is the highest at the configuration with three centrally located obstacles, whereas the lowest is observed at the configuration with three obstacles mounted on one side of the chamber. Compared with the side configuration, the magnitude of overpressure generated increases by approximately 80% and 165% for the central and staggered configurations, respectively. Furthermore, flame propagation speeds and generated overpressures for both the central and staggered configurations are greater, which should to be avoided to reduce the risk associated with turbulent premixed deflagrations in practical processes.     

Effects of vent layout and vent area on dynamic characteristics of premixed methane-air explosion in a tube with two side-vented ducts

To further elucidate the influence mechanism of side vents on the dynamic characteristics of gas explosions in tubes is helpful to design more reasonable vent layouts. In this paper, 9.5% methane-air explosion experiments were conducted in a tube with two side-vented ducts, and the effects of vent layouts and vent areas on the dynamic characteristics of explosion overpressure and flame propagation speed were investigated. The results demonstrate that under the same condition with a single vent area of 100 mm × 100 mm, when only the end vent is open, the maximum explosion overpressure and the maximum flame propagation speed are the highest among the five vent layouts. When the side vents 1 and 2 and the end vent are open, the maximum explosion overpressure is the lowest, and an unusual discovery is that the flame front changes into a hemispherical shape, finger shape, quasi-plane shape, tulip shape and wrinkled structure. When only side vent 1 is open, a unique Helmholtz oscillation occurs, and a new discovery is that there is a consistent oscillation relationship among the overpressure, flame propagation speed and flame structure. Helmholtz oscillation occurs only when a single vent area is 100 mm × 100 mm–60 mm × 60 mm, and the oscillation degree decreases with decreasing vent area. During the vent failure stage, the maximum explosion overpressure is generated, the flame front begins to appear irregular shape, and the flame propagation speed shows a prominent characteristic peak. After the vent failure stage, the driving effect of the end vent on the flame is higher than that of the side vent on the flame. Furthermore, the correlation equations of the mathematical relationships among the maximum explosion overpressure P_red, the static activation pressure P_stat and the vent coefficient K_v under four vent layouts are established, respectively.     

Large-scale dust explosions in vessel-pipe systems

This study investigates dust explosions in vessel-pipe systems to develop a better understanding of dust flame propagation between interconnected vessels and implications for the proper application of explosion isolation systems. Cornstarch dust explosions were conducted in a large-scale setup consisting of a vented 8-m³ vessel and an attached pipe with a diameter of 0.4 m and a length of 9.8 m. The ignition location and effective dust reactivity were varied between experiments. The experimental results are compared against previous experiments with initially quiescent propane-air mixtures, demonstrating a significantly higher reactivity of the dust explosions due to elevated initial turbulence, leading to higher peak pressures and faster flame propagation. In addition, a physics-based model developed previously to predict gas explosion dynamics in vessel-pipe systems was extended for dust combustion. The model successfully predicts the pressure transients and flame progress recorded in the experiments and captures the effects of ignition location and effective dust reactivity.     

Experimental study on methane explosion characteristics with different types of porous media

Porous media has a significant effect on flame and overpressure of methane explosion. In this paper, the pore diameter and thickness of porous media are studied. Nine experimental combinations of different pore diameter and thickness on the propagation of flame and overpressure of methane explosion in a tube are analyzed. The results show that the porous media not only can suppress the explosive flame propagation, but the porous media with large pore diameter can cause deflagration and accelerate the transition of flame from laminar to turbulent. The pore diameter of the porous media mainly determines the quenching of the flame. Simply increasing the thickness of porous media may cause the flame to temporarily stop propagating, but the flame is not completely extinguished for larger pore diameter. However, the deflagration propagation speed of flame is affected by the thickness. The attenuation of overpressure by porous media is mainly reflected in reducing the duration of overpressure and the peak value of overpressure. The smaller the pore diameter, the greater the thickness, and the more remarkable the reduction in overpressure duration and peak value. Suitable pore diameter and thickness of porous media can effectively suppress flame propagation and reduce the maximum value and duration of overpressure.     

Effect of flame propagation regime on pressure evolution of nano and micron PMMA dust explosions

Experiments using an open space dust explosion apparatus and a standard 20 L explosion apparatus on nano and micron polymethyl methacrylate dust explosions were conducted to reveal the differences in flame and pressure evolutions. Then the effect of combustion and flame propagation regimes on the explosion overpressure characteristics was discussed. The results showed that the flame propagation behavior, flame temperature distribution and ion current distribution all demonstrated the different flame structures for nano and micron dust explosions. The combustion and flame propagation of 100 nm and 30 μm PMMA dust clouds were mainly controlled by the heat transfer efficiency between the particles and external heat sources. Compared with the cluster diffusion dominant combustion of 30 μm dust flame, the premixed-gas dominant combustion of 100 nm dust flame determined a quicker pyrolysis and combustion reaction rate, a faster flame propagation velocity, a stronger combustion reaction intensity, a quicker heat release rate and a higher amount of released reaction heat, which resulted in an earlier pressure rise, a larger maximum overpressure and a higher explosion hazard class. The complex combustion and propagation regime of agglomerated particles strongly influenced the nano flame propagation and explosion pressure evolution characteristics, and limited the maximum overpressure.     

T型管道不同封闭状态瓦斯爆燃火焰传播特征

为了研究分岔管道不同封闭状态下瓦斯爆燃火焰阵面传播规律,在自制的T型透明分岔管道内,设置支管端口完全封闭、直管左端口弱封闭,采用光电传感器和压力传感器测试了直管右端弱封闭、完全封闭2种情况下,预混甲烷-空气可燃气体爆燃火焰传播过程中速度、超压参数的变化情况。结果表明:由于分岔的存在,2种封闭状态在支管端点火后瓦斯爆燃火焰阵面在支管中的传播速度均先增大后减小;直管右端弱封闭时,经过分岔后火焰加速向直管两端传播速度基本一致,分别达到86.29 m/s和88.07 m/s;直管右端完全封闭时,火焰向弱封闭端传播速度增大至166.67 m/s,火焰向完全封闭端传播时并不断压缩未燃气体产生高压振荡反馈导致火焰振荡传播现象,火焰速度不断减小至4.84 m/s;管道内瓦斯爆燃超压均迅速上升到达峰值,之后受压缩气体的膨胀和冲击后爆燃产物的振荡作用迅速下降。     

Experiments on the influence of pre-ignition turbulence on vented gas and dust explosions

Experiments were performed on the influence of pre-ignition turbulence on the course of vented gas and dust explosions. A vertical cylindrical explosion chamber of approximately 100 l volume and a length-to-diameter ratio (l/d) of 4.7 consisting of a steel bottom segment and three glass sections connected by steel flanges was used to perform the experiments. Sixteen small fans evenly distributed within the chamber produced turbulent fluctuations from 0 to 0.45 m/s. A Laser-Doppler-anemometer (LDA) was used to measure the flow and turbulence fields. During the experiments the pressure and in the case of dust explosions the dust concentration were measured. In addition, the flame propagation was observed by a high-speed video camera. A propane/nitrogen/oxygen mixture was used for the gas explosion experiments, while the dust explosions were produced by a cornstarch/air mixture.It turned out that the reduced explosion pressure increased with increasing turbulence intensity. This effect was most pronounced for small vents with low activation pressures, e.g. for bursting disks made from polyethylene foil. In this case, the overpressure at an initial turbulence of 0.45 m/s was twice that for zero initial turbulence.     

Study on the characteristics of gas explosion affected by induction charged water mist in confined space

To investigate the suppression effect of charged water mist on gas explosion, a small charged water mist generator and a gas explosion simulation device were designed based on the principle of electrostatic induction. Experiments for testing characteristics of the gas explosion in a confined space under different charged polarities, charged voltages and mist fluxes were carried out. Experimental results indicated that, compared with the normal water mist, the explosion peak overpressure and the flame propagation speed could be more effectively reduced by the charged water mist. And this suppression effect could be promoted by increasing the charged voltage. To visualize the effect of the charged water mist's polarity on gas explosion, comparative experiments were conducted. The results showed that the explosion peak overpressure, the overpressure rising rate, and the propagation speed of the flame were reduced by 64.7%, 33.0% and 19.4%, respectively, when a +8 kV charged voltage was applied. In situation where a -8 kV charged voltage was applied, 64.1%, 26.5% and 16.0% reductions were achieved for the explosion peak overpressure, the overpressure rising rate, and the flame propagation speed respectively. Comparison of this data leads to the conclusion that the gas explosion could be more efficiently suppressed by the positively charged water mist.     

Insight into vented explosion mechanism and premixed flame dynamics in linked vessels: Influence of membrane thickness and blocking rate

To effectively prevent and mitigate explosion hazards and casualties, relief venting of flammable gas explosions has been applied in production processes in a broad variety of industries. This work conducted fully vented experiments to investigate the influence of venting membrane thickness, and partially vented experiments to investigate the influence of baffle blocking rate on the explosion characteristics of 9.5 vol% methane-air mixtures in linked vessels with a 0.5 m long vented duct. Results indicate that the membrane thickness and blocking rate for the two types of vented explosions significantly affected the explosion overpressure. The smaller the membrane thickness and blocking rate, the lower the explosion overpressure. Secondary explosions were observed in the vented duct through experiments and a weaker explosion flame appeared at a small blocking rate of 20%. With the further increase in the blocking rate, the flame became extremely weak, and no secondary explosions occurred. The overpressure evolution process at different positions in the explosion duct and secondary explosion phenomenon in the vented duct were investigated. This work could probably serve as an important reference for the selection of technical parameters of explosion venting in the practical industrial processes.     

Flame behaviors and pressure characteristics of vented dust explosions at elevated static activation overpressures

Dust explosion venting experiments were performed using a 20-L spherical chamber at elevated static activation overpressures larger than 1 bar. Lycopodium dust samples with mean diameter of 70 μm and electric igniters with 0.5 KJ ignition energy were used in the experiments. Explosion overpressures in the chamber and flame appearances near the vent were recorded simultaneously. The results indicated that the flame appeared as the under-expanded free jet with shock diamonds, when the overpressure in the chamber was larger than the critical pressure during the venting process. The flame appeared as the normal constant-pressure combustion when the pressure venting process finished. Three types of venting processes were concluded in the experiments: no secondary flame and no secondary explosion, secondary flame, secondary explosion. The occurrence of the secondary explosions near the vent was related to the vent diameter and the static activation overpressure. Larger diameters and lower static activation overpressures were beneficial to the occurrence of the secondary explosions. In current experiments, the secondary explosions only occurred at the following combinations of the vent diameter and the static activation overpressure: 40 mm and 1.2 bar, 60 mm and 1.2 bar, 60 mm and 1.8 bar.     

Application of the TNO multi-energy and Baker-Strehlow-Tang methods to predict hydrogen explosion effects from small-scale experiments

Analytical models or abacus are of importance to predict explosion effects in open and congested areas for industrial safety reasons. The goal of this work is to compare overpressure and flame speed values of small-scale deflagration experiments to predicted values from the TNO multi-energy (TNO ME) method and the Baker-Strehlow-Tang (BST) method. Experiments were performed in cylindrical congested volumes of hydrogen – air mixtures varying from 1.77 L to 7.07 L. The reactivity was controlled by the equivalence ratio of hydrogen-air mixtures, ranging from 0.5 to 2.5. The congestion was realized with varying numbers of grid layers and configurations. The influence of the obstacle density and the importance of the mixture reactivity to choose the strength index in order to predict the effects of an explosion has been highlighted for the TNO ME method. Predictive flame speed values from the BST method are in accordance with almost half of the experimental results and the method is conservative in most tested configurations. The use of the TNO ME method has been validated on a small-scale experiment to predict maximal overpressures generated by the deflagration of medium and large-scale H₂/air clouds.     

Experimental study on the synergistic inhibition effect of nitrogen and ultrafine water mist on gas explosion in a vented duct

In this study, in order to research the synergistic inhibition effect of nitrogen and ultrafine water mist on gas explosion in a vented duct, a semi-confined transparent chamber was designed with the size of 120 × 120 × 840 mm, and the experiments were carried out with stoichiometric methane/air premixed mixture (fraction of methane: 9.5%), adding different fractions of nitrogen and ultrafine water mist. The experimental results showed the following: The combination of nitrogen and ultrafine water mist had a synergistic inhibiting effect on methane/air explosion, which was preferable to the single use of any kind. With the increase of spraying time of water mist and fraction of nitrogen, the initial shape of the explosion flame became snakelike, and at the same time the peak flame propagation speed and peak overpressure decreased significantly. When the nitrogen fraction was increased to 10% and the mist spraying time was increased to 2min, synergistic inhibiting effect on overpressure was high efficient. However, with the increase of spraying time of water mist and fraction of nitrogen going on, the amount of increase of explosion inhibition efficiency was gradually reduced.     

Effect of initial temperature on explosion characteristics of 2, 3, 3, 3–Tetrafluoropropene

The flammability of refrigerants is a major cause of refrigerant explosion incidents. Studying the explosion characteristics of refrigerants at different initial temperatures can provide significant benefits for solving the safety problems of refrigerants under actual working conditions. This paper studied the effects of the initial temperature and refrigerant concentration on the explosion characteristics of refrigerant 2, 3, 3, 3-tetrafluoropropene (R1234yf) at 0.1 MPa. The curves of explosion characteristics with different initial temperature revealed the same variation trend ranged from 25 °C to 115 °C. Specifically, as the refrigerant concentration was raised, the peak overpressure, the maximum rate of pressure rise, and laminar burning velocity increased initially and decreased afterwards, along with maximum values at the refrigerant concentration of 7.6%. When the refrigerant concentration was 7.6%, the peak overpressure declined exponentially with the initial temperature rise, while the maximum rate of pressure rise increased linearly. The laminar burning velocity calculated from the spherical expansion method indicated that the flame propagation was gradually accelerated by the increase of initial temperature, which coincided with the change of the maximum rate of pressure rise. Meanwhile, experiments and CHEMKIN simulation results demonstrated the effects of elevated temperature from 20 °C to 50 °C on the explosion limits of R1234yf. The lower explosion limit reduced and the upper explosion limit increased with rising initial temperature. In general, R1234yf exhibited moderate combustion and lower explosion risk, compared with traditional refrigerants.     

地下复杂组合受限空间火灾分区现象与初期模式实验研究

主要介绍地下狭长与组合受限空间油料介质火灾分区现象、初期火灾主要模式模拟实验研究结果与讨论;地下组合受限空间火灾呈现出特殊的分区现象。一般可分为燃烧区、新鲜空气补充区、烟气流区、过渡区和火焰后面的“惰化区”五区。有上下两层的地下复杂组合受限空间可分为燃烧区、烟气流区、新鲜空气补充区和“惰化区”4区。地下受限空间(包括组合受限空间、容积式受限空间和狭长受限空间)密闭条件下火灾初期模式主要有：爆炸、爆炸减弱、爆炸增强、燃烧、爆燃向爆轰发展。地下复杂组合受限空间下部与下部狭长受限空间分别全开口条件下着火后火灾主要模式为爆炸、燃烧、爆炸后持续燃烧、爆炸后短时燃烧、爆炸后发展为出口外爆炸;爆炸又可分为爆炸强度逐步加强、爆炸由爆燃发展为爆轰、爆炸强度逐步减弱。