电化学氧化法去除微污染水中的氨氮

以低氯离子浓度下微污染水中的氨氮(NH4+-N)为研究对象,采用电化学氧化法对污染水中的氨氮进行去除。通过静态和正交实验得到了极板的最佳运行参数。实验结果表明:Cl-浓度在各影响因素中对NH4+-N去除影响最大,且在其他影响因素不变的条件下,通过改变电解电流是解决动态运行时NH4+-N去除率下降较经济有效的方法。最佳运行工艺条件为:电流密度10 mA/cm2,电解时间10 min,极板间距1 cm,溶液初始pH为7,Cl-浓度100 mg/L,面体比102 m2/m3,氨氮的平均去除率在80%以上。     

Fe/C微电解耦合H_2O_2氧化处理页岩气钻井废水

采用Fe/C微电解耦合H_2O_2工艺对经复合混凝处理后的某页岩气井钻井废水进行处理,考察了Fe/C质量比、Fe/C投加量、溶液pH值、气水比、H_2O_2(30%)投加量和反应时间对COD去除率的影响。结果表明,耦合工艺最佳实验条件为Fe/C质量比1∶1、Fe/C投加量500 g·L-1、溶液pH值2.5、气水比20∶1、H_2O_2(30%)投加量6 m L·L-1、反应时间120 min。最佳工艺条件下,页岩气钻井废水经处理后,出水COD质量浓度为89.54 mg·L~(-1),去除率达到81.60%。     

铁碳微电解/H_2O_2耦合类Fenton法深度处理制药废水

采用铁碳微电解/H2O2耦合类Fenton法深度处理制药废水,考察不同铁碳比、H2O2投加量、溶液p H及反应时间对COD去除效果的影响,通过单因素实验和正交实验确定最优条件并与铁碳微电解法的去除效果进行对比。结果表明,各因素对COD的去除效果均呈现先增加后降低或趋于稳定的趋势,且对去除效果的影响顺序为:Fe/CH2O2投加量溶液p H反应时间;在固液比为1∶10的条件下,Fe/C(质量比)为1∶1,溶液p H为2.5,反应时间为60 min,H2O2(30%)投加量为12.24 mmol/L时对COD的去除效率最高,可达71.56%;H2O2对铁碳微电解法有显著的加强作用。     

均相催化强化US/FCME协同体系降解硝基苯

考察了NaCl、AlCl3、Na2SiO3、CuSO44种均相催化剂对超声波(US)/铁炭微电解(FCME)协同体系降解硝基苯的催化效果,结果表明,CuSO4的催化效果最好,在体系反应液初始pH为3.0,混合填料投加量为5.0 g/L(铁炭质量比为1∶1),CuSO4投加量为800 mg/L时,体系对硝基苯的降解率达到99.2%,但溶液COD值仅下降了24.6%,矿化效果一般,红外光谱分析表明降解体系的主要中间产物为苯胺。     

响应曲面法优化强化混凝工艺处理微污染水

为进一步提高微污染水中氨氮、有机物去除效果,采用响应曲面法对强化混凝工艺处理微污染水的影响因素和去除效果进行研究,实验以混凝剂投加量、助凝剂投加量和助凝剂投加点为影响因素,浊度、氨氮和COD去除效果为响应值,利用Design-Expert软件对实验数据进行处理,得到二次响应曲面模型,各因素间的交互作用对响应值的影响以及优化水平值。模型优化结果显示,强化混凝处理微污染水的最佳工艺条件为:PAFC投加量17.80 mg·L~(-1),PAM投加量0.39 mg·L~(-1),PAM于快速搅拌结束投加,此时浊度、氨氮、COD的去除率分别为68.03%、10.92%和30.2%,最终通过模型的验证证明了响应曲面法用于优化强化混凝工艺处理微污染水的可行性和有效性。     

Fe/Cu/C微电解深度处理钻井废水

以某油井钻井废水经高效混凝+吸附过滤处理后的出水为研究对象,采用Fe/Cu/C微电解对钻井废水进行深度处理研究。结果表明,Fe/Cu/C微电解的最佳工艺条件为:Fe/Cu/C质量比为7∶3∶10,Fe/Cu/C投加量为1 000 g/L,pH为3.0,气水比为54∶1,反应时间为180 min;Fe/Cu/C微电解对钻井废水深度处理的效能十分显著,在最佳工艺条件下,废水COD质量浓度由428.63 mg/L降至98.32 mg/L,COD去除率达到77.06%。     

铁炭微电解-MAP沉淀法联合预处理垃圾渗滤液

采用铁炭微电解-磷酸氨镁(MAP)沉淀法对垃圾渗滤液进行预处理,实验结果表明,铁炭比为5∶1,pH值为3,反应时间为3 h时,铁炭微电解的COD的去除率为47.5%;在投加药剂n(Mg2+)∶n(PO43-)∶n(NH4+)为1.4∶1∶1,pH值为9,反应时间为1 h的条件下,垃圾渗滤液氨氮去除率达到79.7%。     

Fe-Cu-C三元微电解—Fenton氧化深度处理含油废水的研究

以某石化厂实际生产中经隔油、三级气浮处理后的含油废水(含油量为20～30mg/L)为处理对象,采用Fe-Cu-C三元微电解—Fenton氧化组合工艺进行处理,确定Fe-Cu-C三元微电解体系、Fenton氧化体系的最佳工艺条件。结果表明,Fe-Cu-C三元微电解的最佳工艺条件:Fe/Cu/C为2∶1∶1(质量比),反应时间为45min,溶液初始pH为4,最佳工艺条件下出水除油率可达56%左右;三元微电解出水经Fenton氧化的最优条件:H2O2投加量为1.0mL/L,pH为5,氧化时间为40min,最优条件下的除油率可达到89%以上;采用Fe-Cu-C三元微电解—Fenton氧化组合工艺处理后总除油率可达94%～96%,最终出水含油量稳定在1～2mg/L。     

微电解-混凝法处理抛光液废水

采用微电解-混凝处理抛光液废水,考察了铁水比、进水pH值、铁炭比、振荡时间对微电解处理效果的影响.通过单因素实验与正交实验找出了影响较大的因素,进水pH、铁水比、振荡时间都对去除率影响较大.最佳微电解条件为铁水比为0.375,进水pH为3,铁炭比为1∶1,振荡时间为150 min.同时,当混凝剂硫酸亚铁的投加量为160 mg/L、三氯化铁的投加量为20 mg/L时,COD去除率可达到83.8％,金属铜离子去除率可达到96％.     

电化学氧化法处理含盐苯醌模拟废水

利用钛基二氧化铅电极(Ti/PbO_2)作为电催化活性阳极,通过电化学氧化技术对苯醌进行降解矿化,考察常见共存无机盐对苯醌废水降解效率的影响。结果表明,NaCl存在下苯醌废水溶液的COD去除率相比硝酸盐提高了62%,相比硫酸盐提高了45%,NaCl能够显著增强电氧化去除苯醌的电流效率。苯醌的降解对氯离子非常敏感,存在少量的氯离子即可以引起氧化效率明显增加。氯离子浓度越高,苯醌模拟废水的COD去除率越高;但当氯离子浓度高于0.3mol·L~(-1)时,COD去除率反而有所下降。pH为8的弱碱性环境更有利于含氯离子苯醌废水的电氧化降解反应。提高电流密度可增大COD去除率;但升高温度会降低COD去除率。在pH为8、NaCl浓度为0.3 mol·L~(-1)、电流密度为10mA·cm~(-2)、温度为20℃的条件下,初始浓度为100 mg·L~(-1)的苯醌经3 h电化学氧化降解后COD去除率可达80.9%。通过高效液相色谱对电氧化降解苯醌的中间产物进行分析,发现氯离子存在下苯醌的降解速度显著提高,中间产物顺丁烯二酸的生成速度更快,这说明由氯离子生成的强氧化剂对苯醌具有极强的开环能力。     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

不同泥源对厌氧氨氧化反应器启动的影响

采用2套上流式生物膜反应器,分别接种少量厌氧氨氧化污泥和大量硝化污泥,考察其对厌氧氨氧化反应器启动的影响。污泥接种入反应器后,测得接种厌氧氨氧化污泥的反应器(R1)内MLSS为0.22 g/L,另一个反应器(R2)MLSS为2.7 g/L。与直接接种厌氧氨氧化污泥相比,R1经过72 d的运行才显现出厌氧氨氧化特性。经过114 d的培养,前者氮去除速率由0.23 kg/(m3.d)提升到5.29 kg/(m3.d),总氮去除率大于89%;R2的氮去除速率由0.01 kg/(m3.d)提升到1.1 kg/(m3.d),总氮去除率大于84.6%。说明普通污泥启动需要一个较长的筛选过程,直接接种少量的厌氧氨氧化污泥比接种普通的污泥能够更快启动厌氧氨氧化反应器。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

造纸废水混凝处理中SFT助凝替代性研究

中小造纸厂废水处理常用PAC作混凝剂 ,PAM作助凝剂。由于PAM成本很高 ,影响了处理设备的投运率。用超细滑石粉 (SFT)替代PAM助凝 ,与混凝剂PAC配合 ,其混凝处理效果基本相当 ,但是处理成本降低 0 .10元 /m3 。由于SFT属环境无害材料 ,不会给排泥带来二次污染     

产油微藻培养与回收的关键技术研究进展

寻找廉价而高效的替代原料是实现生物柴油产业化的关键所在.微藻以含油量高、生长周期短、环境适应能力强、生物产量高等优点,有望成为一种极具潜力的生物柴油生产原料.然而,目前尚存在微藻培养低效成本高和微藻回收效率低两大难题.综述了微藻培养与回收过程中的关键技术,并对存在的两大难题及其改进技术进行了详细的探讨.最后,总结并展望了微藻培养、回收技术未来的发展趋势.     

红土吸附砷对其动电电位的影响

研究了遵义红土吸附砷对其动电电位的影响 ,从砷酸根浓度和体系pH对红土动电电位影响的角度作了探讨 ,结果表明 ,砷酸根离子浓度越大 ,Zata电位下降幅度越大 ,Zata电位也越低 ;随着体系pH的升高 ,氧化铁胶体动电电位逐渐下降 ,甚至改变了表面电位的符号。由此得出了红土吸附砷属于专性吸附的结论。     

活性炭三维电极法对印染废水的处理研究

对三维电极方法处理印染废水进行了实验研究,初步探讨了活性炭三维电极法处理印染废水的机理,对影响处理效果的各种要素,如反应时间、槽电压和pH值等进行了条件实验,得出了活性炭三维电极法处理印染废水的最佳运行条件为:停留时间120-180 min,槽电压25～30 V,进水pH值6.5～7.5。结果表明,该反应器能有效地降低废水色度,有较高的COD去除效率,并能提高印染废水的可生化性。     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%(质量百分比).反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.     

Evaluation of the presence of drugs of abuse in tap waters

A total of seventy samples of drinking water were tested for non-controlled and illicit drugs. Of these, 43 were from Spanish cities, 15 from seven other European countries, three from Japan and nine from seven different Latin American countries. The most frequently detected compounds were caffeine, nicotine, cotinine, cocaine and its metabolite benzoylecgonine, methadone and its metabolite EDDP. The mean concentrations of non-controlled drugs were: for caffeine 50 and 19 ng L⁻¹, in Spanish and worldwide drinking water respectively and for nicotine 13 and 19 ng L⁻¹. Illicit drugs were sparsely present and usually at ultratrace level (<1 ng L⁻¹). For example, cocaine has mean values of 0.4 (Spain) and 0.3 ng L⁻¹ (worldwide), whereas for benzoylecgonine, these mean values were 0.4 and 1.8 ng L⁻¹, respectively. Higher concentrations of benzoylecgonine were found in Latin American samples (up to 15 ng L⁻¹). No opiates were identified in any sample but the presence of methadone and EDDP was frequently detected. Total mean values for EDDP were 0.4 ng L⁻¹ (Spain) and 0.3 ng L⁻¹ (worldwide). Very few samples tested positive for amphetamines, in line with the reactivity of chlorine with these compounds. No cannabinoids, LSD, ketamine, fentanyl and PCP were detected.