等离子喷涂 YSZ 涂层瞬态超高温冲蚀性能研究

目的研究等离子喷涂YSZ涂层的瞬态超高温烧蚀性能。方法借助超音速火焰喷涂设备实现超高温高速火焰,对等离子喷涂YSZ涂层进行瞬态冲蚀,通过火焰中加送氧化铝颗粒模拟对涂层的高温冲刷。采用常规手段评价涂层的抗瞬态超高温冲蚀性能,并对冲蚀部位进行微观观察,探讨涂层的失效机理。结果在3000 K、不添加砂粒的条件下,火焰冲击3 s后钢基体材料表面发生沸腾;喷涂0.6 mm YSZ的试样在火焰冲击60 s后涂层完好。在3000 K、添加砂粒的条件下,火焰冲击3 s后钢基体材料被冲刷出约1.0 mm深坑;喷涂0.6 mm YSZ试样的涂层被火焰冲刷剥落,但基体未受明显损伤;喷涂1 mm YSZ的试样,试验后仍保留部分涂层。结论在3000 K高温瞬态冲蚀条件下,热喷涂1 mm厚YSZ涂层可对材料表面形成有效防护。     

YSZ-W复合涂层的制备及抗烧蚀性能研究

目的 在TC4表面制备均匀致密的YSZ-20％(体积分数)W(ZW2)复合涂层,以提高其抗烧蚀性能,并对其在超音速燃流中的烧蚀响应机制进行初步探究.方法 以8YSZ和W粉为原料,采用喷雾干燥-真空烧结工艺制备喷涂用ZW2复合粉末,利用大气等离子喷涂技术(APS)制备ZW2复合涂层,采用超音速火焰冲刷法(SCF)测试涂层...     

等离子喷涂耐高温抗氧化涂层的研究进展

利用等离子喷涂技术在工件表面制备抗高温氧化涂层,能显著提高工件的抗氧化性能。综述了目前国内外抗高温氧化涂层和热障涂层的研究现状。详细介绍了金属间化合物和MCrA lY两种耐高温抗氧化涂层的组织性能及其抗氧化原理。阐述了影响热障涂层性能的3种主要因素,分析了热障涂层由于热生长氧化层(TGO)的存在而引起的失效机制。指出了等离子喷涂制备耐高温抗氧化涂层存在的主要问题,并提出了几种解决思路,展望了等离子喷涂制备抗氧化涂层的应用前景。     

Cf/SiC 复合材料表面 HfO2涂层的制备及其抗热冲击性能研究

目的研究等离子喷涂条件下Cf/SiC复合材料表面HfO_2涂层的物相、显微组织及其抗热冲击性能。方法通过水热合成和喷雾造粒制备出HfO_2粉体,并利用等离子喷涂在Cf/SiC复合材料表面制备HfO_2涂层,研究涂层的物相、显微组织和抗热冲击性能。结果水热合成的纳米HfO_2为单斜相结构,颗粒的平均粒径为10~15nm;等离子喷涂制备的HfO_2涂层组织中存在微裂纹和孔隙,涂层为单斜相结构,且经1350℃热处理后涂层的相结构未发生改变。等离子喷涂的HfO_2涂层与Cf/SiC复合材料基体结合良好,未观察到涂层、基体间界面分离的现象。经1350℃、50周次的空冷热冲击试验后,涂层未发生破坏失效;在1350℃水冷热冲击条件下,热循环20次时涂层表面出现剥落,27次时脱落面积50%。结论通过等离子喷涂制备的HfO_2涂层与Cf/SiC复合材料基体结合良好,涂层能够抵御1350℃空冷、50周次热冲击,且未发生破坏失效,涂层的1350℃水冷热循环寿命达27次。     

低压等离子喷涂制备ZrB2-TiC复合涂层 及其烧蚀性能研究

目的探索低压等离子喷涂制备ZrB_2-TiC复合涂层工艺及其烧蚀性能。方法采用喷雾造粒技术制备适用于低压等离子喷涂的ZrB_2-TiC球形粉体,再采用低压等离子喷涂技术在高强石墨基体表面制备ZrB_2-TiC复合涂层。利用氧-乙炔火焰考核涂层的抗烧蚀性能,采用红外测温仪测试烧蚀过程中涂层的表面温度,分别采用扫描电镜、EDS及XRD分析涂层的表截面形貌、元素及物相。结果 ZrB_2-TiC复合涂层呈等离子喷涂层状结构特征,内部孔隙率达到10.8%,涂层与高强石墨之间的结合强度约5.4 MPa。喷涂后涂层产生了ZrTiB4、ZrTiC2新相。涂层经过2000℃氧乙炔烧蚀5min后,保持完整,未出现裂纹及剥落,烧蚀深度仅为2～5μm。结论采用低压等离子喷涂可在石墨表面制备性能优良的ZrB_2-TiC复合涂层,涂层可有效抵御氧乙炔火焰的烧蚀。     

ZrO2掺杂对La2Ce2O7力学和热物理性能 影响的研究

目的提高La_2Ce_2O_7(LC)陶瓷材料的断裂韧性。方法采用固相反应方法合成Y_2O_3稳定ZrO_2(YSZ)掺杂的La_2Ce_2O_7(LC)陶瓷材料(LCZ),研究LCZ块材的弹性模量、断裂韧性等力学性能,以及热膨胀系数、热传导率等热物理性能。结果 10%YSZ摩尔分数掺杂的LCZ块材的断裂韧性约为1.4 MPa·m1/2,比LC提高了近10%。YSZ掺杂有效地抑制了LC在200～400℃温度区间热膨胀系数下降的现象。在200～1200℃温度范围内,LCZ块材的热膨胀系数为10×10-6～12×10-6K-1,在1200℃的热导率约为0.75W/(m·K),比YSZ降低了50%以上,显示了优异的隔热性能。结论 YSZ的掺杂使LC中部分Zr4+取代了La3+,降低了晶格中的O空位浓度,原子的横向剪切运动被削弱,有效地抑制了LC在200～400℃温度区间热膨胀系数下降的现象。由于t-ZrO_2→m-ZrO_2的相变对微裂纹的愈合作用,10%YSZ掺杂使LC块材的断裂韧性得到有效提高。     

超级爆炸喷涂镍基钴基涂层高温氧化及摩擦磨损性能

目的针对装备向高温高速发展的需求,开展NiCr-Cr_3C_2、CoMoCr及NiCr Al Y涂层的高温摩擦磨损性能对比研究。方法针对上述三种涂层,通过超级爆炸喷涂工艺进行涂层制备,并测试涂层孔隙率、显微硬度、结合强度等基本性能,开展650℃/260 h的抗氧化试验和400、650℃的销盘式摩擦磨损试验,对比涂层的各项性能和在高温条件下的氧化质量增量、摩擦系数、磨损质量损失。结果抗氧化试验后,NiCr-Cr_3C_2、CoMoCrSi及NiCrAlY涂层氧化增重0.18、0.1、0.005 mg/(cm~2·h)。650℃时,摩擦系数分别为0.5、1.0、0.6。结论超级爆炸喷涂工艺制备的涂层组织、结合强度均优于等离子喷涂等常规喷涂工艺。高温下的氧化产物Co_3O_4与Cr_2O_3对高温摩擦系数有不同的影响。NiCr-75Cr_3C_2和NiCrAlY涂层在400、650℃可作为与SG37A材料的对磨副材料。     

大气等离子和超音速火焰喷涂CoCrAlYSi-hBN涂层组织和性能对比

目的 针对航空发动机叶片榫头/榫槽摩擦副工作中的微动磨损问题,开展CoCrAlYSi-hBN抗微动磨损涂层研究.方法 通过大气等离子(APS)和超音速火焰(HVOF)喷涂工艺,制备CoCrAlYSi-hBN涂层,采用扫描电镜(SEM)研究涂层的形貌和微观组织,采用显微硬度计和拉伸试验机测试涂层的显微硬度和结合强度,采用SRV试验机探究涂层的摩擦磨损性能.结果 APS喷涂CoCrAlYSi-hBN涂层熔化更充分,显微组织均匀,具有更多高含量的hBN和孔隙;HVOF喷涂CoCrAlYSi-hBN涂层显微组织具有明显的层状结构,涂层致密,hBN和孔隙含量少;APS喷涂CoCrAlYSi-hBN涂层的硬度平均值为168.4HV0.3,结合强度平均值为44.6 MPa,远小于HVOF喷涂CoCrAlYSi-hBN涂层的硬度(327.1HV0.3)和结合强度平均值(59.5 MPa).相比HVOF喷涂CoCrAlYSi-hBN涂层,APS喷涂CoCrAlYSi-hBN涂层虽然有更低的摩擦系数(0.75),但涂层磨损更严重,涂层磨痕表面有明显的涂层剥落,HVOF喷涂CoCrAlYSi-hBN涂层磨痕则出现更多的犁沟.结论 HVOF喷涂工艺制备的CoCrAlYSi-hBN涂层的综合性能优于APS喷涂CoCrAlYSi-hBN涂层,在摩擦过程中,两种工艺制备的CoCrAlYSi-hBN涂层都会转移到对偶件上,从而减少对偶件的磨损,有作为叶片榫头抗微动磨损涂层的潜力.     

爆炸喷涂制备BaF2+CaF2+Cr3 C2/Ni-Cr涂层的组织及性能

采用爆炸喷涂工艺制备出BaF2＋CaF2＋Cr3C2／Ni—Cr涂层,为找到粉末性质对涂层性能的影响关系,利用XRD衍射分析、光学显微分析、扫描电镜分析、能谱分析及显微硬度分析等方法研究对比了不同种类粉末制备出的涂层的形貌、成分及显微硬度。研究结果表明,BaF2＋CaF2＋Cr3C2／Ni—Cr粉末在爆炸喷涂制备涂层的过程中氟化物会有损失,涂层中的Ca元素和Ba元素的质量分数低于其在粉末中的质量分数;包覆型粉的沉积效率高于机械混合型粉,前者制备的涂层中氟化物含量稍高于后者。     

Gd2O3-NiO 共掺对钇稳定氧化锆材料热物理性能的影响

目的研究Gd_2O_3-NiO共掺对钇稳定氧化锆材料热物理性能的影响。方法采用高温固相反应法制得Gd_2O_3-NiO共掺YSZ陶瓷材料。分别利用XRD、扫描电镜观察、激光导热仪、傅立叶红外光谱仪对陶瓷材料的晶体结构、微观结构、热扩散系数及红外透过率进行表征,并对其热导率进行分析。结果 Gd_2O_3-NiO共掺YSZ后,陶瓷材料单斜相含量减少,室温至1300℃的热导率相比YSZ降低,在2.5~5μm波长范围内红外透过率降低。结论 Gd_2O_3-NiO共掺对YSZ陶瓷材料热导率的影响机理为掺杂Gd_2O_3和NiO导致YSZ中单斜相(M)、四方相(T)和立方相(C)含量发生变化,同时YSZ晶格发生畸变。对YSZ辐射传热的影响机理为通过在YSZ中掺杂过渡金属元素Ni使陶瓷材料吸收特定波长的光,进而有效地降低在2.5~5μm短波长的红外透过率,降低其高温下的红外辐射传热。     

Effects of two sludge application on fractionation and phytotoxicity of zinc and copper in the soil

The potential harm of heavy metals is a primary concern in application of sludge to the agricultural land. A pot experiment was conducted to evaluate the effect of two sludges on fractionation of Zn and Cu in soil and their phytotoxicity to pakchoi. The loamy soil was mixed with 0%, 20%, 40%, 60% and 80% (by weight) of digested sewage sludge (SS) and composted sludge (SC). The additions of both sludges caused a significant raise in all fractions, resulting in that exchangeable (EXCH) and organic bound (OM) became predominance of Zn and organic bound Cu occupied the largest portion. There was more available amount of Zn and Cu in SS treatments than SC treatments. During the pot experiment, the concentration of Zn in EXCH, carbonate (CAR) and OM and Cu in EXCH and OM fractions decreased in all treatments, so their bioavailability reduced. Germination rate and plant biomass decreased when the addition rate was high and the best yield appeared in 20% mixtures at the harvest of pakchoi. The two sludges increased tissue contents of Zn and Cu especially in the SS treatments. Zn in pakchoi was not only in relationship to ΔEXCH and ΔCAR forms but also in ΔOM forms in the sludge-soil mixtures. Tissue content of Cu in pakchoi grown on SC-soils could not be predicted by ΔEXCH. These correlation rates between Zn and Cu accumulation in pakchoi and variation of different fractions increased with time, which might indicate that sludges represented stronger impacts on the plant in long-term land application.     

Intraspecific differences in effects of co-contamination of cadmium and

A hydroponic experiment was carried out to study intraspecific differences in the effects of different concentrations of cadmium (Cd)(0-10 mg/L) and arsenate (As(V)) (0-8 mg/L) on the growth parameters and accumulation of Cd and As in six wheat varieties Jing-9428, Duokang-1, Jingdong-11, Jing-411, Jingdong-8 and Zhongmai-8. The endpoints of wheat seedlings, including seed germination,biomass, root length and shoot height, decreased with increasing the Cd and As concentrations. Significant differences in seed germination, biomass, root length, shoot height and the accumulation of Cd and As were observed between the treatments and among the varieties (p ＜ 0.05). The lethal dosage 50% were about 20, 80, 60, 60, 80 and 20 mg As/L for Jing-9428, Duokang-1, Jingdong-11,Jing-411, Jingdong-8 and Zhongmai-8, respectively, and the corresponding values for Cd were about 30, 80, 20, 40, 60 and 10 mg Cd/L, respectively. Among the six varieties, Duokang-1 was found to be the most resistant to Cd and As toxicity, and Zhongmai-8 was the most sensitive to Cd and As co-contamination. The resistance of the six varieties was found dependant on the seedling uptake of Cd and As. Duokang-1 was the most suitable for cultivation in Cd and As co-contaminated soils.     

EDTA-enhanced phytoremediation of lead contaminated soil by Bidens maximowicziana

Phytoremediation is a potential cleanup technology for the removal of heavy metals from contaminated soils.Bidens maximowicziana is a new Pb hyperaccumulator,which not only has remarkable tolerance to Pb but also extraordinary accumulation capacity for Pb.The maximum Pb concentration was 1509.3 mg/kg in roots and 2164.7 mg/kg in overground tissues.The Pb distribution order in the B. maximowicziana was:leaf>stem>root.The effect of amendments on phytoremediation was also studied.The mobility of soil Pb and the Pb concentrations in plants were both increased by EDTA application.Compared with CK(control check),EDTA application promoted translocation of Pb to overground parts of the plant.The Pb concentrations in overground parts of plants was increased from 24.23-680.56 mg/kg to 29.07-1905.57 mg/kg.This research demonstrated that B.maximowicziana appeared to be suitable for phytoremediation of Pb contaminated soil,especially,combination with EDTA.     

Distribution and ecological effect of mercury in Laogang landfill, Shanghai, China

Laogang landfill near Shanghai is the largest landfill in China, and receives about 10000 t of daily garbage per day, Samples of topsoil and plants were analyzed to evaluate mercury pollution from the landfill. For topsoil samples, there were significant correlations among total mercury （HgT）, combinative mercury （Hgc） and gaseous mercury （HgG）, and content of total organic carbon （TOC）, but, no significantly relationship was found between Hg content and filling time. Hg content changes in vertical profiles with time showed that the average Hgv of profiles 1992, 1996, and 2000 was similar, but their average HgG was quite different. HgT was significantly correlated with Hgc in profile 1992 and 2000, and Hgv was significantly correlated with Hg6 in profile 1996. HgG/Hgv ratio in profile samples decreased in the order of （HgG,/HgT）1992〉（HgG/HgT）1996〉〉（HgG/HgT）2000. A simple outline of Hg release in landfill could be drawn： with increasing of filling time, degradation undergoes different biodegradation, accordingly, gaseous mercury goes through small, more, and small proportion to total mercury. Distribution of Hg in plants was inhomogeneous, following the order of leaf〉root〉stem. The highest value of leaf may be associated with higher atmospheric Hg from landfill. Ligneous plants （e.g. Phyllostachys glanca, Prunus salicina and Ligustrum lucidum） are capable of enriching more Hg than herbaceous plants.     

Toxic effects of acetochlor, methamidophos and their combination on nifH gene in soil

Toxic effects of two agrochemicals on nifH gene in agricultural black soil were investigated using denaturing gradient gel electrophoresis （DGGE） and sequencing approaches in a microcosm experiment. Changes of soil nifH gene diversity and composition were examined following the application of acetochlor, methamidophos and their combination. Acetochlor reduced the nifH gene diversity （both in gene richness and diversity index values） and caused changes in the nifH gene composition. The effects of acetochlor on nifH gene were strengthened as the concentration of acetochlor increased. Cluster analysis of DGGE banding patterns showed that nifH gene composition which had been affected by low concentration of acetochlor （50 mg/kg） recovered firstly. Methamidophos reduced nifH gene richness that except at 4 weeks. The medium concentration of methamidophos （150 mg/kg） caused the most apparent changes in nifH gene diversity at the first week while the high concentration of methamidophos （250 mg/kg） produced prominent effects on nifH gene diversity in the following weeks. Cluster analysis showed that minimal changes of nifH gene composition were found at 1 week and maximal changes at 4 weeks. Toxic effects of acetochlor and methamidophos combination on nifH gene were also apparent. Different nifH genes （bands） responded differently to the impact of agrochemicals： four individual bands were eliminated by the application of the agrochemicals, five bands became predominant by the stimulation of the agrochemicals, and four bands showed strong resistance to the influence of the agrochemicals. Fifteen prominent bands were partially sequenced, yielding 15 different nifH sequences, which were used for phylogenetic reconstructions. All sequences were affiliated with the alpha- and beta-proteobacteria, showing higher similarity to eight different diazotrophic genera.     

Enzymatic oxidation of aqueous pentachlorophenol

The influence of the nonionic surfactant Tween 80 on pentachlorophenol （PCP） oxidation catalyzed by horseradish peroxidase was studied. The surfactant was tested at concentrations below and above its critical micelle concentration （CMC）. Enhancement of PCP removal was observed at sub-CMCs. The presence of Tween 80 in the reaction mixture reduced enzyme inactivation which occurred through a combination of free radical attack and sorption by precipitated products. A simple first-order model was able to simulate time profiles for enzyme inactivation in the presence or absence of Tween 80. At supra-CMCs, the surfactant caused noticeable reductions in PCP removal, presumably through micelle partitioning of PCP which precluded the hydrophobic PCP molecule from interacting with the enzyme.     

Decomposition of alachlor by ozonation and its mechanism

Decomposition and corresponding mechanism of alachlor, an endocrine disruptor in water by ozonation were investigated. Results showed that alachlor could not be completely mineralized by ozone alone. Many intermediates and final products were formed during the process, including aromatic compounds, aliphatic carboxylic acids, and inorganic ions. In evoluting these products, some of them with weak polarity were qualitatively identified by GC-MS. The information of inorganic ions suggested that the dechlorination was the first and the fastest step in the ozonation of alachlor.     

Arsenic uptake by arbuscular mycorrhizal maize （Zea mays L.） grown in an arsenic-contaminated soil with added phosphorus

The effects of arbuscular mycorrhizal (AM) fungus (Glomus mosseae) and phosphorus (P) addition (100 mg/kg soil) on arsenic (As) uptake by maize plants (Zea mays L.) from an As-contaminated soil were examined in a glasshouse experiment.Non-mycorrhizal and zero-P addition controls were included.Plant biomass and concentrations and uptake of As,P,and other nutrients,AM colonization,root lengths,and hyphal length densities were determined.The results indicated that addition of P significantly inhibited root colonization and development of extraradical mycelium.Root length and dry weight both increased markedly with mycorrhizal colonization under the zero-P treatments,but shoot and root biomass of AM plants was depressed by P application.AM fungal inoculation decreased shoot As concentrations when no P was added,and shoot and root As concentrations of AM plants increased 2.6 and 1.4 times with P addition,respectively.Shoot and root uptake of P,Mn,Cu,and Zn increased,but shoot Fe uptake decreased by 44.6%,with inoculation, when P was added.P addition reduced shoot P,Fe,Mn,Cu,and Zn uptake of AM plants,but increased root Fe and Mn uptake of the nonmycorrhizal ones.AM colonization therefore appeared to enhance plant tolerance to As in low P soil,and have some potential for the phytostabilization of As-contaminated soil,however,P application may introduce additional environmental risk by increasing soil As mobility.     

Degradation of metabolites accumulated of benzo[a]pyrene by coupling Penicillium Chrysogenum with KMnO4

Several main metabolites of benzo[a]pyrene （BaP） formed by Penicillium chrysogenum, Benzo[a]pyrene-1,6-quinone （BP 1,6- quinone）, trans-7,8-dihydroxy-7,8-dihydrobenzo[a]pyrene （BP 7,8-diol）, 3-hydroxybenzo[a]pyrene （3-OHBP）, were identified by high-performance liquid chromatography （HPLC）. The three metabolites were liable to be accumulated and were hardly further metabolized because of their toxicity to microorganisms. However, their further degradation was essential for the complete degradation of BaP. To enhance their degradation, two methods, degradation by coupling Penicillium chrysogenum with KMnO4 and degradation only by Penicillium chrysogenum, were compared; Meanwhile, the parameters of degradation in the superior method were optimized. The results showed that （1） the method of coupling Penicillium chrysogenum with KMnO4 was better and was the first method to be used in the degradation of BaP and its metabolites; （2） the metabolite, BP 1,6-quinone was the most liable to be accumulated in pure cultures; （3） the effect of degradation was the best when the concentration of KMnO4 in the cultures was 0.01% （w/v）, concentration of the three compounds was 5 mg/L and pH was 6.2. Based on the experimental results, a novel concept with regard to the bioremediation of BaP-contaminated environment was discussed, considering the influence on environmental toxicity of the accumulated metabolites.     

Impact of atrazine and nitrogen fertilizers on the sorption of chlorotoluron in soil and model sorbents

Sorption of chlorotoluron in ammonium sulfate, urea and atrazine multi-solutes system was investigated by batch experiments. The results showed application of nitrogen fertilizers to the soil could affect the behavior of chlorotoluron. At the same concentration of N, sorption of chlorotoluron decreased as the concentration of atrazine increased on the day 0 and 6 in soil, respectively. The sorption of chlorotoluron increased from 0 to 6 d when soils were preincubated with deionized water, ammonium sulfate and urea solution for 6 d. That indicated incubation time was one of the most important factors for the sorption of chlorotoluron in nitrogen fertilizers treatments. The individual sorption isotherms of chlorotoluron in rubbery polymer and silica were strictly linear in single solute system, but there were competition sorption between pesticides or between pesticides and nitrogen fertilizers. That indicated the sorption taken place by concurrent solid-phase dissolution mechanism and sorption on the interface of water-organic matter or water-mineral matter.