Suitability of passive sampling for the monitoring of pharmaceuticals in Finnish surface waters

The occurrence of five pharmaceuticals, consisting of four anti-inflammatory and one antiepileptic drug, was studied by passive sampling and grab sampling in northern Lake Päijänne and River Vantaa. The passive sampling was performed by using Chemcatcher® sampler with a SDB-RPS Empore disk as a receiving phase. In Lake Päijänne, the sampling was conducted during summer 2013 at four locations near the discharge point of a wastewater treatment plant and in the years 2013 and 2015 at four locations along River Vantaa. The samples were analyzed by liquid chromatography coupled to tandem mass spectrometry (LC-MS/MS) in the multiple reaction monitoring mode. The concentrations of carbamazepine, diclofenac, ibuprofen, ketoprofen, and naproxen in Lake Päijänne determined by passive sampling ranged between 1.4–2.9 ng L^?1, 15–35 ng L^?1, 13–31 ng L^?1, 16–27 ng L^?1, and 3.3–32 ng L^?1, respectively. Similarly, the results in River Vantaa ranged between 1.2–40 ng L^?1, 15–65 ng L^?1, 13–33 ng L^?1, 16–31 ng L^?1, and 3.3–6.4 ng L^?1. The results suggest that the Chemcatcher passive samplers are suitable for detecting pharmaceuticals in lake and river waters.     

Tea bag filter paper as a novel protective membrane for micro-solid phase extraction of butachlor in aqueous samples

An innovative, cost-effective, simple, and environmental friendly tea bag filter paper protected micro-solid phase extraction (μ-SPE) technique was developed for the first time with the aim to miniaturize and minimize the use of organic solvents for the extraction and determination of butachlor in aqueous samples. The μ-SPE device was produced by packing 3.0 mg of an easily synthesized new sorbent, hydroxyl-functionalized polypyrrole (OH-PPY), inside a small tea bag filter paper sachet (1.0 cm × 0.5 cm) that served as a protective envelope. Both the extraction and desorption procedures were facilitated by sonication. Due to the high porosity and the fast water absorption of the tea bag filter paper, the analyte could easily diffuse through and enhance the interaction with the sorbent. Under the optimized conditions for the GC-ECD and the μ-SPE, the limit of detection (S/N ≥ 3) was 2.0 μg L^?1 while the limit of quantitation (S/N ≥ 10) was 10.0 μg L^?1. The recoveries of the butachlor spiked at 0.050, 0.10, and 0.50 μg mL^?1 ranged from 77.9 ± 3.0 to 112.5 ± 2.9%. The proposed method was successfully applied for the determination of butachlor in water samples from paddy cultivation sites. The levels found were from non-detectable to 24.71 ± 0.37 μg L^?1.     

Heterogeneous Fenton degradation of bisphenol A catalyzed by efficient adsorptive Fe3O4/GO nanocomposites

A new method for the degradation of bisphenol A (BPA) in aqueous solution was developed. The oxidative degradation characteristics of BPA in a heterogeneous Fenton reaction catalyzed by Fe₃O₄/graphite oxide (GO) were studied. Transmission electron microscopic images showed that the Fe₃O₄ nanoparticles were evenly distributed and were ～6 nm in diameter. Experimental results suggested that BPA conversion was affected by several factors, such as the loading amount of Fe₃O₄/GO, pH, and initial H₂O₂ concentration. In the system with 1.0 g L^?1 of Fe₃O₄/GO and 20 mmol L^?1 of H₂O₂, almost 90 % of BPA (20 mg L^?1) was degraded within 6 h at pH 6.0. Based on the degradation products identified by GC–MS, the degradation pathways of BPA were proposed. In addition, the reused catalyst Fe₃O₄/GO still retained its catalytic activity after three cycles, indicating that Fe₃O₄/GO had good stability and reusability. These results demonstrated that the heterogeneous Fenton reaction catalyzed by Fe₃O₄/GO is a promising advanced oxidation technology for the treatment of wastewater containing BPA.     

Spatial distribution and partitioning of polychlorinated biphenyl and organochlorine pesticide in water and sediment from Sarno River and Estuary,Southern Italy

The Sarno River is nicknamed “the most polluted river in Europe”. The main goal of this study is to enhance our knowledge on the Sarno River water and sediment quality and on its environmental impact on the gulf of Naples (Tyrrhenian Sea, Central Mediterranean Sea) in order to become a useful assessment tool for the regional administrations. For these reasons, 32 selected polychlorinated biphenyls (PCBs) and aldrin, α-BHC, β-BHC, δ-BHC, γ-BHC (lindane), 4,4′-DDD, 4,4′-DDE, 4,4′-DDT, dieldrin, endosulfan I, endosulfan II, endosulfan sulphate, endrin, endrin aldehyde, heptachlor, heptachlor epoxide (isomer B) and methoxychlor were determined in the water dissolved phase (DP), suspended particulate matter (SPM) and sediments. Total concentrations of PCBs ranged from 1.4 to 24.9 ng L^?1 in water (sum of DP and SPM) and from 1.01 to 42.54 ng g^?1 in sediment samples. The concentrations of total organochlorine pesticides (OCPs) obtained in water (sum of DP and SPM) ranged from 0.54 to 7.32 ng L^?1 and from 0.08 to 5.99 ng g^?1 in sediment samples. Contaminant discharges of PCBs and OCPs into the sea were calculated in about 1,247 g day^?1 (948 g day^?1 of PCBs and 326 g day^?1 of OCPs), showing that this river should account as one of the main contribution sources of PCBs and OCPs to the Tyrrhenian Sea.     

A simple method to prepare magnetic modified beer yeast and its application for cationic dye adsorption

The purpose of this research is to use a simple method to prepare magnetic modified biomass with good adsorption performances for cationic ions. The magnetic modified biomass was prepared by two steps: (1) preparation of pyromellitic dianhydride (PMDA) modified biomass in N, N-dimethylacetamide solution and (2) preparation of magnetic PMDA modified biomass by a situ co-precipitation method under the assistance of ultrasound irradiation in ammonia water. The adsorption potential of the as-prepared magnetic modified biomass was analyzed by using cationic dyes: methylene blue and basic magenta as model dyes. Optical micrograph and x-ray diffraction analyses showed that Fe₃O₄ particles were precipitated on the modified biomass surface. The as-prepared biosorbent could be recycled easily by using an applied magnetic field. Titration analysis showed that the total concentration of the functional groups on the magnetic PMDA modified biomass was calculated to be 0.75 mmol g^?1 by using the first derivative method. The adsorption capacities (q _m) of the magnetic PMDA modified biomass for methylene blue and basic magenta were 609.0 and 520.9 mg g^?1, respectively, according to the Langmuir equation. Kinetics experiment showed that adsorption could be completed within 150 min for both dyes. The desorption experiment showed that the magnetic sorbent could be used repeatedly after regeneration. The as-prepared magnetic modified sorbent had a potential in the dyeing industry wastewater treatment.     

Kinetics of imidazolium-based ionic liquids degradation in aqueous solution by Fenton oxidation

In the last few years, several works dealing with Fenton oxidation of ionic liquids (ILs) have proved the capability of this technology for their degradation, achieving complete ILs removal and non-toxic effluents. Nevertheless, very little is known about the kinetics of this process, crucial for its potential application. In this work, the effect of several operating conditions, including reaction temperature (50–90 °C), catalyst load (10–50 mg L^?1 Fe³⁺), initial IL concentration (100–2000 mg L^?1), and hydrogen peroxide dose (10–200% of the stoichiometric amount for the complete IL mineralization) on 1-butyl-3-methylimidazolium chloride ([C₄mim]Cl) oxidation has been investigated. Under the optimum operating conditions (T = 90 °C; [Fe³⁺]₀ = 50 mg L^?1; [H₂O₂]₀ = 100% of the stoichiometric amount), the complete removal of [C₄mim]Cl (1000 mg L^?1) was achieved at 1.5-min reaction time. From the experimental results, a potential kinetic model capable to describe the removal of imidazolium-based ILs by Fenton oxidation has been developed. By fitting the proposed model to the experimental data, the orders of the reaction with respect to IL initial concentration, Fe³⁺ amount and H₂O₂ dose were found to be close to 1, with an apparent activation energy of 43.3 kJ mol^?1. The model resulted in a reasonable fit within the wide range of operating conditions tested in this work.     

Trace analysis of parabens preservatives in drinking water treatment sludge,treated, and mineral water samples

Parabens have been widely used as antimicrobial agents, mainly in food products, pharmaceuticals, and cosmetics. Although they are known as safe preservatives, they also cause some harm to human health, which has been discussed lately. Therefore, the aim of this study was to evaluate the occurrence of nine parabens (including isomers) in mineral and drinking waters, besides in drinking water treatment sludge (DWTS) samples with determination by liquid chromatography tandem mass spectrometry (LC-MS/MS). Both methods solid phase extraction (SPE) and QuEChERS were validated. Calibration curves showed a correlation coefficient of 0.99 for all compounds. LOQ values ranged from 0.04 to 4 μg L^?1 in aqueous matrices and from 5 to 500 ng g^?1 in DWTS. Recoveries between 70 and 115% were reached with RSD below 20% for all compounds in SPE whereas recoveries between 62 and 119% were found with RSD below 20% for almost all compounds in QuEChERS. Matrix effect had low values (<?20%); it was only above 20% for methylparaben in the SPE and for pentylparaben in the QuEChERS. Using a quick and simple extraction procedures with SPE, QuEChERS, and LC-MS/MS analyses, these methods proved to be selective and sensitive. They were successfully applied to real samples (treated water, mineral water, and sludge), and methylparaben was detected at concentration levels below 0.242 μg L^?1 in mineral and treated water samples and 10 ng g^?1 in DWTS samples.     

Effect of deposit age on adsorption and desorption behaviors of ammonia nitrogen on municipal solid waste

Ammonia nitrogen pollution control is an urgent issue of landfill. This research aims to select an optimal refuse for ammonia nitrogen removal in landfill from the point of view of adsorption and desorption behavior. MSW (municipal solid waste) samples which deposit ages were in the range of 5 to 15 years (named as R₁₅, R₁₁, R₇, and R₅) were collected from real landfill site. The ammonia nitrogen adsorption behaviors of MSW including equilibrium time, adsorption isotherms, and desorption behaviors including equilibrium time were determined. Furthermore, the effects of pH, OM, Cu(II), Zn(II), and Pb(II) on adsorption and desorption behavior of ammonia nitrogen were conducted by orthogonal experiment. The equilibrium time of ammonia nitrogen adsorption by each tested MSW was very short, i.e., 20 min, whereas desorption process needed 24 h and the ammonia nitrogen released from refuses was much lesser than that adsorbed, i.e., accounted for 3.20 % (R₁₅), 14.32 % (R₁₁), 20.59 % (R₇), and 20.50 % (R₅) of each adsorption quantity, respectively. The maximum adsorption capacity estimated from Langmuir isotherm appeared in R₁₅-KCl, i.e., 25,000 mg kg^?1. The best condition for ammonia nitrogen removal from leachate was pH >7.5, OM 23.58 %, Cu(II) <5 mg L^?1, Zn(II) <10 mg L^?1, and Pb(II) <1 mg L^?1. Ammonia nitrogen in landfill leachate could be quickly and largely absorbed by MSW but slowly and infrequently released. The refuse deposited for 15 years could be a suitable material for ammonia nitrogen removal.     

Influence of operational key parameters on the photocatalytic decolorization of Rhodamine B dye using Fe2+/H2O2/Nb2O5/UV system

The present research deals with the development of a new heterogeneous photocatalysis and Fenton hybrid system for the removal of color from textile dyeing wastewater as Rhodamine B (RhB) solutions by using Fe²⁺/H₂O₂/Nb₂O₅ as a photocatalytic system. The application of this photocatalytic system for the decolorization of dye contaminants is not reported in the literature yet. Different parameters like dye concentration, Nb₂O₅/Fe²⁺ catalyst amount, pH, and H₂O₂ concentration have been studied. The optimum conditions for the decolorization of the dye were initial concentration of 10 mg L^?1 of dye, pH 4, and Nb₂O₅/Fe²⁺ catalyst concentration of 0.5 g L^?1/50 mg L^?1. The optimum value of H₂O₂ concentration for the conditions used in this study was 700 mg L^?1. Moreover, the efficiency of the Nb₂O₅/photo-Fenton hybrid process in comparison to photo-Fenton alone and a dark Fenton process as a control experiment to decolorize the RhB solution has been investigated. The combination of photo-Fenton and Nb₂O₅ catalysts has been proved to be the most effective for the treatment of such type of wastewaters. The results revealed that the RhB dye was decolorized in a higher percent (78 %) by the Nb₂O₅/photo-Fenton hybrid process (Fe²⁺/H₂O₂/Nb₂O₅/UV) than by the photo-Fenton process alone (37 %) and dark Fenton process (14 %) after 120 min of treatment. Moreover, the Nb₂O₅ catalyst as a heterogeneous part of the photocatalytic system was demonstrated to have good stability and reusability.     

Environmentally friendly system for the degradation of multipesticide residues in aqueous media by the Fenton’s reaction

A Fenton oxidation system employing zero-valent iron (whose source was swarf, a residue of metallurgical industries, in powder form) and hydrogen peroxide for the treatment of an aqueous solution with six pesticides was developed, and the effect of the iron metal content, pH, and hydrogen peroxide concentration was evaluated. The characterization of the aqueous solution resulted in: pH 5.6, 105 mg L^?1 of dissolved organic carbon, and 44.6 NTU turbidity. In addition, the characterization of the swarf by FAAS and ICP-MS showed 98.43?±?7.40 % of zero-valent iron. The removal was strongly affected by the content of iron metal, pH, and hydrogen peroxide concentration. The best degradation conditions were 2.0 g swarf, pH 2.0, and 5 mmol L^?1 H₂O₂. At the end of the treatment, the pesticide degradation ranged from 60 to 100 %, leading to 55 % mineralization. Besides, all hydrogen peroxide was consumed and the determination of total dissolved iron resulted in 2 mg L^?1. Thus, the advantages of this system are rapid degradation (up to 20 min), high-degradation rates, simple handling, and low cost.

Acute toxicity and ecotoxicological risk assessment of rice pesticides to Lithobates catesbeianus tadpoles

The objective of this study was to determine the acute toxicity of some pesticides used in irrigated rice farming to Lithobates catesbeianus tadpoles. The LC_50-96h for commercial formulations containing bentazon, penoxsulam, vegetable oil, permethrin and carbofuran, separately and their mixtures, were determined at the proportions commonly used in the field. The limits of risk concentrations of these products for the studied species were also established. The LC_50-96h for tadpoles was 4,530 mg L^?1 for bentazon; 7.52 mg L^?1 for penoxsulam + 145.66 mg L^?1 of vegetable oil; 81.57 mg L^?1 for vegetable oil; 0.10 mg L^?1 for permethrin; 29.90 mg L^?1 for carbofuran (active ingredients), and 38.79 times the dose used in the field for the mixture of these products. The environmental risk was determined only for permethrin, and care should be taken when using the vegetable oil.     

Degradation of ethylenethiourea pesticide metabolite from water by photocatalytic processes

In this study, photocatalytic (photo-Fenton and H₂O₂/UV) and dark Fenton processes were used to remove ethylenethiourea (ETU) from water. The experiments were conducted in a photo-reactor with an 80 W mercury vapor lamp. The mineralization of ETU was determined by total organic carbon analysis, and ETU degradation was qualitatively monitored by the reduction of UV absorbance at 232 nm. A higher mineralization efficiency was obtained by using the photo-peroxidation process (UV/H₂O₂). Approximately 77% of ETU was mineralized within 120 min of the reaction using [H₂O₂]₀ = 400 mg L^?1. The photo-Fenton process mineralized 70% of the ETU with [H₂O₂]₀ = 800 mg L^?1 and [Fe²⁺] = 400 mg L^?1, and there is evidence that hydrogen peroxide was the limiting reagent in the reaction because it was rapidly consumed. Moreover, increasing the concentration of H₂O₂ from 800 mg L^?1 to 1200 mg L^?1 did not enhance the degradation of ETU. Kinetics studies revealed that the pseudo-second-order model best fit the experimental conditions. The k values for the UV/H₂O₂ and photo-Fenton processes were determined to be 6.2 × 10^?4 mg L^?1 min^?1 and 7.7 × 10^?4 mg L^?1 min^?1, respectively. The mineralization of ETU in the absence of hydrogen peroxide has led to the conclusion that ETU transformation products are susceptible to photolysis by UV light. These are promising results for further research. The processes that were investigated can be used to remove pesticide metabolites from drinking water sources and wastewater in developing countries.     

Risk assessment of PBDEs and PAHs in house dust in Kocaeli,Turkey: levels and sources

Indoor dust samples were collected from 40 homes in Kocaeli, Turkey and were analyzed simultaneously for 14 polybrominated diphenyl ethers (PBDEs) and 16 poly aromatic hydrocarbons (PAHs) isomers. The total concentrations of PBDEs (Σ₁₄PBDEs) ranged from 29.32 to 4790 ng g^?1, with a median of 316.1 ng g^?1, while the total indoor dust concentrations of 16 PAHs (Σ₁₆PAHs) extending over three to four orders of magnitude ranged from 85.91 to 40,359 ng g^?1 with a median value of 2489 ng g^?1. Although deca-PBDE products (BDE-209) were the principal source of PBDEs contamination in the homes (median, 138.3 ng g^?1), the correlation in the homes was indicative of similar sources for both the commercial penta and deca-PBDE formulas. The PAHs diagnostic ratios indicated that the main sources of PAHs measured in the indoor samples could be coal/biomass combustion, smoking, and cooking emissions. For children and adults, the contributions to ∑₁₄PBDEs exposure were approximately 93 and 25 % for the ingestion of indoor dust, and 7 and 75 % for dermal contact. Exposure to ∑₁₆PAHs through dermal contact was the dominant route for both children (90.6 %) and adults (99.7 %). For both groups, exposure by way of inhalation of indoor dust contaminated with PBDEs and PAHs was negligible. The hazard index (HI) values for BDE-47, BDE-99, BDE-153, and BDE-209 were lower than the safe limit of 1, and this result suggested that none of the population groups would be likely to experience potential health risk due to exposure to PBDEs from indoor dust in the study area. Considering only ingestion + dermal contact, the carcinogenic risk levels of both B2 PAHs and BDE-209 for adults were 6.2 × 10^?5 in the US EPA safe limit range while those for children were 5.6 × 10^?4 and slightly higher than the US EPA safe limit range (1 × 10^?6 and 1 × 10^?4). Certain precautions should be considered for children.     

Understanding the patterns and mechanisms of urban water ecosystem degradation: phytoplankton community structure and water quality in the Qinhuai River, Nanjing City, China

The temporal and spatial distribution characteristics of environmental parameters and the phytoplankton community were investigated in October 2010 and January 2011 in the Qinhuai River, Nanjing, China. Results showed that the water quality in the study area was generally poor, and the main parameters exceeding standards (level V) were nitrogen and phosphorus. The observed average concentrations of the total nitrogen (TN) were 4.90 mg?L^?1 in autumn and 9.29 mg?L^?1 in winter, and those of the total phosphorus (TP) were 0.24 mg?L^?1 in autumn and 0.88 mg?L^?1 in winter, respectively. Thirty-seven species, 30 genera, and four phyla of phytoplankton were detected in the river. Cyanophyta and Bacillariophyta were the dominant phyla in autumn, with average abundance and biomass of 221.5?×?10⁴?cells?L^?1 and 4.41 mg?L^?1, respectively. The dominant population in winter was Bacillariophyta, and the average abundance and biomass were 153.4?×?10⁴?cells?L^?1 and 6.58 mg?L^?1, respectively. The results of canonical correspondence analysis (CCA) between environmental parameters and phytoplankton communities showed that Chlorophyta could tolerate the higher concentrations of the permanganate index, nitrogen, and phosphorus in eutrophic water; Bacillariophyta could adapt well to changing water environments; and the TN/TP ratio had obvious impacts on the distributions of Cyanophyta, Euglenophyta, and some species of Chlorophyta. CCA analyses for autumn and winter data revealed that the main environmental parameters influencing phytoplankton distribution were water temperature, conductivity, and total nitrogen, and the secondary factors were dissolved oxygen, NH₄ ⁺–N, NO₃–N, TN, COD_Mn, TN/TP ratio, and oxidation-reduction potential.     

Aminocyclopyrachlor sorption-desorption and leaching from three Brazilian soils

This study aimed to evaluate the sorption-desorption and leaching of aminocyclopyrachlor from three Brazilian soils. The sorption-desorption of ¹⁴C-aminocyclopyrachlor was evaluated using the batch method and leaching was assessed in glass columns. The Freundlich model showed an adequate fit for the sorption-desorption of aminocyclopyrachlor. The Freundlich sorption coefficient [K_{f (sorption)}] ranged from 0.37 to 1.34 µmol ^(1–1/n) L^1/n kg^?1 and showed a significant positive correlation with the clay content of the soil, while the K_{f (desorption)} ranged from 3.62 to 5.36 µmol ^(1–1/n) L^1/n kg^?1. The K_{f (desorption)} values were higher than their respective K_{f (sorption)}, indicating that aminocyclopyrachlor sorption is reversible, and the fate of this herbicide in the environment can be affected by leaching. Aminocyclopyrachlor was detected at all depths (0?30 cm) in all the studied soils, where leaching was influenced by soil texture. The total herbicide leaching from the sandy clay and clay soils was <0.06%, whereas, ～3% leached from the loamy sand soil. The results suggest that aminocyclopyrachlor has a high potential of leaching, based on its low sorption and high desorption capacities. Therefore, this herbicide can easily contaminate underground water resources.     

Psychotropic drugs in mixture alter swimming behaviour of Japanese medaka (<Emphasis Type="Italic">Oryzias latipes</Emphasis>) larvae above environmental concentrations

Psychiatric pharmaceuticals, such as anxiolytics, sedatives, hypnotics and antidepressors, are among the most prescribed active substances in the world. The occurrence of these compounds in the environment, as well as the adverse effects they can have on non-target organisms, justifies the growing concern about these emerging environmental pollutants. This study aims to analyse the effects of six psychotropic drugs, valproate, cyamemazine, citalopram, sertraline, fluoxetine and oxazepam, on the survival and locomotion of Japanese medaka Oryzias latipes larvae. Newly hatched Japanese medaka were exposed to individual compounds for 72 h, at concentrations ranging from 10 μg L^?1 to 10 mg L^?1. Lethal concentrations 50 % (LC₅₀) were estimated at 840, 841 and 9,136 μg L^?1 for fluoxetine, sertraline and citalopram, respectively, while other compounds did not induce any significant increase in mortality. Analysis of the swimming behaviour of larvae, including total distance moved, mobility and location, provided an estimated lowest observed effect concentration (LOEC) of 10 μg L^?1 for citalopram and oxazepam, 12.2 μg L^?1 for cyamemazine, 100 μg L^?1 for fluoxetine, 1,000 μg L^?1 for sertraline and >10,000 μg L^?1 for valproate. Realistic environmental mixture of the six psychotropic compounds induced disruption of larval locomotor behaviour at concentrations about 10- to 100-fold greater than environmental concentrations.     

Rapid metal extractability tests from polluted mining soils by ultrasound probe sonication and microwave-assisted extraction systems

Ultrasonic probe sonication (UPS) and microwave-assisted extraction (MAE) were used for rapid single extraction of Cd, Cr, Cu, Ni, Pb, and Zn from soils polluted by former mining activities (Mónica Mine, Bustarviejo, NW Madrid, Spain), using 0.01 mol L^?1 calcium chloride (CaCl₂), 0.43 mol L^?1 acetic acid (CH₃COOH), and 0.05 mol L^?1 ethylenediaminetetraacetic acid (EDTA) at pH 7 as extracting agents. The optimum extraction conditions by UPS consisted of an extraction time of 2 min for both CaCl₂ and EDTA extractions and 15 min for CH₃COOH extraction, at 30% ultrasound (US) amplitude, whereas in the case of MAE, they consisted of 5 min at 50 °C for both CaCl₂ and EDTA extractions and 15 min at 120 °C for CH₃COOH extraction. Extractable concentrations were determined by inductively coupled plasma atomic emission spectrometry (ICP-AES). The proposed methods were compared with a reduced version of the corresponding single extraction procedures proposed by the Standards, Measurements and Testing Programme (SM&T). The results obtained showed a great variability on extraction percentages, depending on the metal, the total concentration level and the soil sample, reaching high values in some areas. However, the correlation analysis showed that total concentration is the most relevant factor for element extractability in these soil samples. From the results obtained, the application of the accelerated extraction procedures, such as MAE and UPS, could be considered a useful approach to evaluate rapidly the extractability of the metals studied.     

Determination of phenols and pharmaceuticals in municipal wastewaters from Polish treatment plants by ultrasound-assisted emulsification–microextraction followed by GC–MS

A method combining ultrasound-assisted emulsification–microextraction (USAEME) with gas chromatography–mass spectrometry (GC–MS) was developed for simultaneous determination of four acidic pharmaceuticals, ibuprofen, naproxen, ketoprofen, and diclofenac, as well as four phenols, 4-octylphenol, 4-n-nonylphenol, bisphenol A, and triclosan in municipal wastewaters. Conditions of extraction and simultaneous derivatization were optimized with respect to such aspects as type and volume of extraction solvent, volume of derivatization reagent, kind and amount of buffering salt, location of the test tube in the ultrasonic bath, and extraction time. The average correlation coefficient of the calibration curves was 0.9946. The LOD/(LOQ) values in influent and effluent wastewater were in the range of 0.002–0.121/(0.005–0.403) μg L^?1 and 0.002–0.828/(0.006–2.758) μg L^?1, respectively. Quantitative recoveries (≥94 %) and satisfactory precision (average RSD 8.2 %) were obtained. The optimized USAEME/GC–MS method was applied for determination of the considered pharmaceuticals and phenols in influents and treated effluents from nine Polish municipal wastewater treatment plants. The average concentration of acidic pharmaceuticals in influent and effluent wastewater were in the range of 0.06–551.96 μg L^?1 and 0.01–22.61 μg L^?1, respectively, while for phenols were in the range of 0.03–102.54 μg L^?1 and 0.02–10.84 μg L^?1, respectively. The removal efficiencies of the target compounds during purification process were between 84 and 99 %.     

Distribution and ecological risk of polychlorinated biphenyls (PCBs) and organochlorine pesticides (OCPs) in surface sediments from the Bizerte lagoon,Tunisia

Polychlorinated biphenyls (PCBs) and organochlorine pesticides (OCPs) were determined in 18 surface sediment samples collected from Bizerte lagoon, Tunisia. The total concentrations of ten PCBs (∑PCBs) and of four OCPs (∑OCPs) in the sediments from this area ranged from 0.8 to 14.6 ng g^?1 dw (average value, 3.9 ng g^?1 dw) and from 1.1 to 14.0 ng g^?1 dw (average value, 3.3 ng g^?1 dw), respectively. Among the OCPs, the range of concentrations of dichlorodiphenyltrichloroethane and its metabolites (DDTs) and hexachlorobenzene (HCB) were 0.3–11.5 ng g^?1 dw (1.9 ng g^?1 dw) and 0.6–2.5 ng g^?1 dw (1.4 ng g^?1 dw), respectively. Compositional analyses of the POPs indicated that PCB 153, 138 and 180 were the predominant congeners accounting for 60 % of the total PCBs. In addition, p,p′-DDT was found to be the dominant DDTs, demonstrating recent inputs in the environment. Compared with some other regions of the world, the Bizerte lagoon exhibited low levels of PCBs and moderate levels of HCB and DDTs. The high ratios ΣPCBs/ΣDDTs indicated predominant industrial versus agricultural activities in this area. According to the established guidelines for sediment quality, the risk of adverse biological effects from such levels of OCPs and PCBs, as recorded at most of the study sites, was insignificant. However, the higher concentrations in stations S1 and S3 could cause biological damage.     

Insights into real cotton-textile dyeing wastewater treatment using solar advanced oxidation processes

Different advanced oxidation processes (AOPs) were applied to the treatment of a real cotton-textile dyeing wastewater as a pre-oxidation step to enhance the biodegradability of the recalcitrant compounds, which can be further oxidized using a biological process. Tests were conducted on a lab-scale prototype using artificial solar radiation and at pilot scale with compound parabolic collectors using natural solar radiation. The cotton-textile dyeing wastewater presents a lilac color, with a maximum absorbance peak at 641 nm, alkaline pH (pH?=?8.2), moderate organic content (DOC?=?152 mg C L^?1, COD?=?684 mg O₂ L^?1) and low-moderate biodegradability (40 % after 28 days in Zahn–Wellens test). All the tested processes contributed to an effective decolorization and mineralization, but the most efficient process was the solar-photo-Fenton with an optimum catalyst concentration of 60 mg Fe²⁺ L^?1, leading to 98.5 % decolorization and 85.5 % mineralization after less than 0.1 and 5.8 kJ_UV L^?1, respectively. In order to achieve a final wastewater with a COD below 250 mg O₂ L^?1 (discharge limit into water bodies imposed by the Portuguese Legislation-Portaria no. 423/97 of 25 June 1997), considering the combination of a solar-photo-Fenton reaction with a biological process, the phototreatment energy required is 0.5 kJ_UV L^?1, consuming 7.5 mM hydrogen peroxide, resulting in 58.4 % of mineralization $ \left({t}_{30\mathrm{W}}=3.2\ \min; \overline{T}=30.7\ {}^{\circ}\mathrm{C};\overline{\mathrm{pH}}=2.80;{\overline{\mathrm{UV}}}_{G,n}={13\ \mathrm{W}\ \mathrm{m}}^{-2}\right). $