纳米TiO2协助下As（Ⅲ）在可变电荷土壤中的光催化氧化和吸附

环境中As(Ⅲ)的毒性和活动性均大于As(Ⅴ),将A8(Ⅲ)转化为As(Ⅴ)有利于砷的固定.为此使用自制的光催化装置,采用一次平衡法研究了纳米TiO2协助下As(Ⅲ)在土壤悬液体系中的光催化氧化及土壤对氧化产物的吸附.结果表明,As(Ⅲ)的光催化氧化量随TiO2的加入量和光照时间的增加而增加,当TiO2的加入量为1.0 g·L-1,光照时间为90 min时As(Ⅲ)可以达到很好的转化效果.As(Ⅲ)在土壤中的光催化氧化及土壤对氧化产物的吸附增加了水体中砷的去除量,在Fe/Al氧化物与TiO2体系中也观察到类似的效应.实验结果还表明γ-Al2O3也可诱导As(Ⅲ)的光催化氧化.     

无机砷和甲基砷在水稻体内吸收运移的比较研究

由于含甲基砷的农药残留或土壤中微生物的砷甲基化作用,除了无机砷,水稻籽粒中也可以检测到相当含量的不同形态的甲基砷.通过水培试验研究了不同形态砷在水稻幼苗中的吸收、转运、转化和外排.结果表明,水稻中各形态砷的含量排序为:亚砷酸盐(As(Ⅲ))>单甲基砷盐(MMA(Ⅴ))>砷酸盐(As(Ⅴ))>二甲基砷盐(DMA(Ⅴ)),但从地下部向地上部的转运系数排序为:DMA(Ⅴ)>As(Ⅲ)>As(Ⅴ)>MMA(Ⅴ).实验中未发现水稻体内无机砷向甲基砷的转化,甲基砷向无机砷的转化比例也较低,但观察到MMA(Ⅴ)部分被还原为MMA(Ⅲ).相比其地上部和地下部的吸收量,DMA(Ⅴ)在水稻中通过木质部(向上)和韧皮部(向下)的转运比例在4种形态砷中最高.甲基砷(MMA(Ⅴ)和DMA(Ⅴ))通过根系外排的速率和比例明显的高于无机砷(As(Ⅲ)和As(Ⅴ)).实验结果表明,不同形态砷的累积与其在水稻体内的吸收、运移及砷的根系外排密切相关.     

纳米Fe3C/炭纤维非均相电芬顿降解二甲基砷的研究

针对结构稳定且难以靠常规方法去除的二甲基砷,制备新型负载Fe_3C纳米粒子的炭纤维催化剂,并对其非均相电芬顿降解二甲基砷进行了研究.结果表明,纳米Fe_3C/CF与阴极产生的H2O2发生电芬顿催化反应产生羟基自由基将二甲基砷降解为一甲基砷和As(V),As(V)可被同步吸附在Fe_3C/CF催化剂表面.通过考察电催化过程中初始p H、反应物初始浓度、电流强度和催化剂投加量等因素对催化氧化DMA效果的影响,表明在初始p H为3,二甲基砷初始浓度为5 mg·L~(-1),Fe_3C/CF投量为500 mg·L~(-1)的最佳条件下,经非均相电芬顿反应360 min后,二甲基砷去除率高达96%.     

二氧化钛光催化氧化阿散酸

阿散酸(p-arsanilic acid,ASA)是一种重要的有机砷化合物,较无机砷更加难以去除,目前关于去除水中ASA研究少有报道.本研究主要评价了TiO_2光催化剂(P25)对ASA的去除效果,考察了P25投量、pH和光照强度对其光催化氧化ASA的影响,探究了ASA光降解产物和主要机制.结果表明,在P25催化作用下,模拟自然光可氧化降解ASA为As(V),最终通过P25对As(V)的吸附作用将水中砷有效去除.当ASA初始浓度为2 mg·L~(-1),P25投量为1 g·L~(-1)时,光催化氧化-吸附0.5 h后,水中剩余砷的浓度约为0.34 mg·L~(-1).酸性条件下ASA的去除率远远高于碱性条件,最佳光照强度为68.5 mW·cm~(-2).P25光催化氧化ASA过程中羟基自由基起到了主要作用.     

长期暴露下纳米二氧化钛对典型淡水藻体砷累积与生物转化的影响

以铜绿微囊藻(Microcystis aeruginosa)和斜生栅藻(Scenedesmus obliquus)为研究对象,通过室内培养实验,研究了长期暴露下纳米二氧化钛(nano-TiO_2)对五价砷[As(Ⅴ)]在典型淡水藻体中累积与生物转化的影响.结果表明不同藻类对无机砷的吸收和转化能力差异很大.长期暴露下斜生栅藻累积的砷(As,以DW计,下同)高达(819.66±11.25)μg·g-1,比铜绿微囊藻累积的As[(355.95±8.31)μg·g-1]高2倍多.Nano-TiO_2可增加藻体对As的吸收累积,降低了培养基中As的含量.同时,nano-TiO_2可增加藻体对As(Ⅴ)的生化转化;其中,铜绿微囊藻中有机砷以二甲基砷(DMA)为主,而斜生栅藻中有机砷以一甲基砷(MMA)为主.另外,长期暴露下nano-TiO_2处理的铜绿微囊藻和斜生栅藻向培养基释放的甲基砷小于对照组,表明长期暴露中的nano-TiO_2不能促进藻体内甲基砷的释放.研究结果可促进nano-TiO_2与As相互作用时生态风险的理解.     

纳米Au/TiO2薄膜真空紫外光催化降解甲醛

为提高真空紫外光催化对甲醛的去除率并降低副产物O3的浓度,采用低温吸附法在TiO2薄膜上负载纳米Au.研究比较了UV254nm光催化(TiO2/UV)、真空紫外光降解(VUV)、真空紫外光催化(TiO2/VUV)等3种方法对低浓度甲醛的降解效果.结果表明,TiO2/VUV对甲醛的去除率显著高于VUV和TiO2/UV.TiO2表面负载纳米Au粒子能促进光生电子和空穴的分离.因此,在真空紫外光催化降解过程中, Au/TiO2不仅提高甲醛的降解率,还显著分解副产物臭氧,使尾气臭氧浓度降低32%.而且Au/TiO2薄膜在真空紫外光催化过程中具有很好的稳定性.     

光催化氧化处理垃圾渗滤液的研究

通过实验，研究分析了不同催化剂(Ti2、ZnO)、pH值、光照时间对垃圾渗滤液光催化氧化的影响，得出：TiO2光催化氧化效果明显优于ZnO的效果，TiO2光催化氧化对CODcr去除率为72％；pH值对光催化氧化影响不大，pH值为5～9均可；光照时间60min效果最好。     

HPLC-(UV)-HG-AFS联用技术测定市售紫菜中砷形态

为优化高效液相色谱-氢化物发生-原子荧光光谱(HPLC-HG-AFS法)同时测定As(III)、DMA、MMA、As(V)和AsB五种砷形态的方法,选用不同提取剂和流动相测定了市售紫菜中砷的形态,考察不同比例甲醇-水溶液作为提取剂、不同流动相对测定紫菜中砷形态的影响。试验结果表明:流动相选择5mmol/L(NH4)2HPO4,在pH值为9.0时能有效分离五种砷形态;市售紫菜中的总砷含量为7.9~13.0mg/kg,未检测到As(III)、As(V)、MMA和DMA;通过对比不同比例甲醇-水溶液的提取效果,发现1∶9甲醇-水溶液和3∶1甲醇-水溶液提取紫菜中砷形态的提取效果较好。该试验结果可为紫菜等植物样品中砷形态的提取提供参考。     

负载银纳米TiO_2光催化降解农药废水的研究

通过对纳米TiO2及其复合材料光催化降解有机磷农药的研究,分析了在不同催化剂、不同浓度AgNO3浸渍、不同pH值和不同光照时间下的光催化降解效果,说明负载银纳米TiO2催化剂对有机磷农药废水有很好的催化性。     

纳米TiO2协助下As(Ⅲ)在可变电荷土壤中的光催化氧化和吸附

环境中As(Ⅲ)的毒性和活动性均大于As(Ⅴ),将As(Ⅲ)转化为As(Ⅴ)有利于砷的固定.为此使用自制的光催化装置,采用一次平衡法研究了纳米TiO₂协助下As(Ⅲ)在土壤悬液体系中的光催化氧化及土壤对氧化产物的吸附.结果表明,As(Ⅲ)的光催化氧化量随TiO₂的加入量和光照时间的增加而增加,当TiO₂的加入量为1.0 g·L^-1,光照时间为90 min时As(Ⅲ)可以达到很好的转化效果.As(Ⅲ)在土壤中的光催化氧化及土壤对氧化产物的吸附增加了水体中砷的去除量,在Fe/Al氧化物与TiO₂体系中也观察到类似的效应.实验结果还表明γ-Al₂O₃也可诱导As(Ⅲ)的光催化氧化.     

Rubber sheet strewn with TiO2 particles:Photocatalytic activity and recyclability

A new method for the preparation of rubber sheet strewn with titanium dioxide particles (TiO₂-strewn sheet) is presented. This simple and low cost method is based on the use of TiO₂ powder (Degussa P25) being strewn onto the sheet made from rubber latex (60% HA) through a steel sieve. The characteristic of the TiO₂-strewn sheet was studied by using scanning electron microscopy/energy dispersive X-ray spectrometer (SEM/EDS) and X-ray diffractometer (XRD) techniques. The photocatalytic activity of TiO₂-strewn rubber sheet was evaluated using Indigo Carmine (IC) dye as a model for organic dye pollutant in water. The results showed that the TiO₂-strewn sheet could degrade IC dye solution under UV light irradiation. The effects of pH, initial concentration, and the intensity of UV light on the photodegradation were also investigated. Kinetics of the photocatalytic degradation was of the first-order reaction. The used TiO₂-strewn sheet can be recovered and reused. The recycling uses did not require any cleaning between successive uses and no decline in the photodegradation efficiency was observed compared with freshly prepared TiO₂-strewn sheet.     

BiOCl/TiO2的氯化改性及其新式光生自由基催化反应

采用溶胶凝胶法制备了BiOCl/TiO₂复合催化剂,透射电镜（TEM）照片显示,两种半导体分布均匀、相互连接,形成的异质结可以为电子传导提供有效通道.经过氯化处理的复合材料具备更强的光催化能力,在紫外光条件下对苯的降解率达到90%,是原BiOCl/TiO₂的2倍、纯TiO₂的10倍.本文利用X射线光电子能谱、红外光谱和电子顺磁共振,对表面氯化的机理进行研究.结果表明,氯元素以Ti—Cl的方式吸附在催化剂表面,在光照条件下光生空穴夺取一个电子,使其生成氯自由基,进而配合超氧、羟基,构成一种新型的三自由基光催化体系,使催化降解能力大幅提升.最后,利用实验方法得到了光生氯自由基的直接证据,并构建了该体系的光催化反应机理.     

不同光源下TiO2/ACF同时脱硫脱硝实验研究

实验室制备了负载型二氧化钛光催化剂TiO₂/ACF,利用自行设计的光催化反应器,在紫外和可见2种光源下进行了同时脱硫脱硝试验,确定了最佳的试验条件,比较了2种不同光源下的脱除效率.结果表明,烟气中氧含量、反应温度、烟气含湿量、光照强度等是影响光催化的主要因素,在紫外光源的照射下,负载型TiO₂/ACF光催化剂脱除SO₂和NO的效率分别达到99.7%和64.3%,在可见光源的照射下,负载型TiO₂/ACF光催化剂脱除SO₂和NO的效率分别达到97.5%和49.6%, 5次平行试验结果表明,平行数据的标准偏差S较小.通过反应后吸收液的离子色谱分析,推测了2种不同光源下同时脱硫脱硝的反应机制.     

Photoelectrocatalytic degradation of high COD dipterex pesticide by using TiO2/Ni photo electrode

A TiO₂ thin film electrode deposited on porous nickel net (TiO₂/Ni) was prepared by the sol-gel method, and the surface morphology, crystal structure features and the grain size were characterized by Field emission scan electron microscopy (FESEM) and X-ray diffraction (XRD). The photoelectrocatalytic system was set up using a UV high-pressure mercury lamp as the light source, TiO₂ coated on foamed nickel as photo anode, Pt sheet as counter electrode and the pesticide dipterex in synthetic wastewater. Various factors that influence the photoelectrocatalytic decomposition of dipterex pesticide have been studied, such as degradation time, the type of electrolyte, current density, original pH value and different degradation methods. The prepared catalysts were employed to photoelectrocatalytically degrade the pesticide dipterex under UV irradiation, comparing the results with photocatalytic degradation and electrochemical oxidation. The results indicated that under the optimal conditions of 0.02 mol/L NaCl as the supporting electrolyte, current density = 2.5 mA/cm², pH 6.0 and dipterex pesticide 40 mg/L, and reaction time 2 hr, dipterex chemical oxygen demand (COD) removal rate and organophosphorous conversion of up to 82.6% and 83.5% were achieved, respectively. The method of photoelectrocatalytic degradation is more efficient than photocatalysis and electrochemical oxidation. The possible roles of the electrolytes on the reactions and probable mechanisms were also discussed.     

Enhanced photocatalytic activity of fish scale loaded TiO2 composites under solar light irradiation

Fish scale (FS) loaded TiO₂ composites were investigated as photocatalysts in degradation of Methyl Orange under solar light irradiation. Composites were prepared through sol-gel method by varying mass ratio of TiO₂/FS at 90:10, 70:30 and 50:50, respectively. The catalysts prepared in this study were characterized by using XRD, SEM, FT-IR and nitrogen sorption. The effects of solar irradiation, mass ratio of TiO₂/FS composites, irradiation time and catalyst loadings were studied. Synergistic effect was found in TiO₂/FS of 90:10 composite which performed higher photocatalytic degradation than synthesized TiO₂ under solar light irradiation. However, further increasing fish scale content in the composites reduced the photocatalytic activity drastically. Under solar light irradiation, all the catalysts in this study exhibited photocatalytic activity, except TiO₂/FS of 50:50 composite that only acted as a weak biosorbent without performing any photocatalytic property. Photocatalytic degradation increased with increasing catalyst loading and irradiation time but decreased with increased of initial dye concentration.     

In_2TiO_5纳米带的静电纺丝法制备及光催化性能

以酞酸丁酯(Ti(OC_4H_9)_4)、硝酸铟(In(NO3)3)和聚乙烯吡咯烷酮(PVP-K30)为原料,采用静电纺丝技术制备了In_2TiO_5纳米带.利用X射线衍射(XRD)、扫描电子显微镜(SEM)、紫外-可见漫反射光谱(UV-vis DRS)和氮气吸附-脱附等温线(BET)等技术对样品进行了表征.考察了In_2TiO_5纳米带在光催化降解罗丹明B(RhB)、甲基橙(MO)、亚甲基蓝(MB)和左氧氟沙星(LEV)过程中的应用性能,研究了不同离子型物质、溶液的pH和MB起始浓度对In_2TiO_5纳米带光催化活性的影响.结果表明:In_2TiO_5纳米带具有正交晶系结构,禁带宽度为3.47 eV,比表面积为20.71 m~2·g~(-1),可应用于4种不同离子型物质的光催化降解,发现光催化效果与被降解物质的表面带电性质有关.在紫外光照射下,90 min,对MB的降解率达98.1%,其降解过程服从一级动力学模型.     

Effect of TiO2 calcination temperature on the photocatalytic oxidation of gaseous NH3

Carbon-modified titanium dioxide(TiO2) was prepared by a sol-gel method using tetrabutyl titanate as precursor, with calcination at various temperatures, and tested for the photocatalytic oxidation(PCO) of gaseous NH3 under visible and UV light. The test results showed that no samples had visible light activity, while the TiO2 calcined at 400℃ had the best UV light activity among the series of catalysts, and was even much better than the commercial catalyst P25. The catalysts were then characterized by X-ray diffractometry, Brunauer-Emmett-Teller adsorption analysis, Raman spectroscopy, thermogravimetry/differential scanning calorimetry coupled with mass spectrometry, ultraviolet-visible diffuse reflectance spectra, photoluminescence spectroscopy and in situ diffuse reflectance infrared Fourier transform spectroscopy. It was shown that the carbon species residuals on the catalyst surfaces induced the visible light adsorption of the samples calcined in the low temperature range( 300℃). However, the surface acid sites played a determining role in the PCO of NH3 under visible and UV light over the series of catalysts. Although the samples calcined at low temperatures had very high SSA, good crystallinity, strong visible light absorption and also low PL emission intensity, they showed very low PCO activity due to their very low number of acid sites for NH3 adsorption and activation. The TiO2 sample calcined at 400℃ contained the highest number of acid sites among the series of catalysts, therefore showing the highest performance for the PCO of NH3 under UV light.     

Visible light responsive N-F-codoped TiO2 photocatalysts for the degradation of 4-chlorophenol

Visible light responsive N-F-codoped TiO₂ photocatalysts exhibit a higher catalytic activity than N-doped TiO₂ for the degradation of 4-chlorophenol due to the synergistic effect of nonmetal elements.     

Photocatalytic parameters and kinetic study for degradation of dichlorophenol-indophenol (DCPIP) dye using highly active mesoporous TiO2 nanoparticles

Highly active mesoporous TiO_2 of about 6 nm crystal size and 280.7 m~2/g specific surface areas has been successfully synthesized via controlled hydrolysis of titanium butoxide at acidic medium. It was characterized by means of XRD(X-ray diffraction), SEM(scanning electron microscopy), TEM(transmission electron microscopy), FT-IR(Fourier transform infrared spectroscopy), TGA(thermogravimetric analysis), DSC(differential scanning calorimetry) and BET(Brunauer–Emmett–Teller) surface area. The degradation of dichlorophenol-indophenol(DCPIP) under ultraviolet(UV) light was studied to evaluate the photocatalytic activity of samples. The effects of different parameters and kinetics were investigated. Accordingly, a complete degradation of DCPIP dye was achieved by applying the optimal operational conditions of 1 g/L of catalyst, 10 mg/L of DCPIP, pH of 3 and the temperature at 25 ± 3°C after 3 min under UV irradiation. Meanwhile, the Langmuir–Hinshelwood kinetic model described the variations in pure photocatalytic branch in consistent with a first order power law model.The results proved that the prepared TiO_2 nanoparticle has a photocatalytic activity significantly better than Degussa P-25.