Design of a Leaching Test Framework for Coal Fly Ash Accounting for Environmental Conditions

Fly ash from coal combustion contains trace elements which, on disposal or utilisation, may leach out, and therefore be a potential environmental hazard. Environmental conditions have a great impact on the mobility of fly ash constituents as well as the physical and chemical properties of the fly ash. Existing standard leaching methods have been shown to be inadequate by not representing possible disposal or utilisation scenarios. These tests are often criticised on the grounds that the results estimated are not reliable as they are not able to be extrapolated to the application scenario. In order to simulate leaching behaviour of fly ash in different environmental conditions and to reduce deviation between measurements in the fields and the laboratories, it is vital to study sensitivity of the fly ash constituents of interest to major factors controlling leachability. pH, liquid-to-solid ratio, leaching time, leachant type and redox potential are parameters affecting stability of elements in the fly ash. Sensitivity of trace elements to pH and liquid to solid ratio (as two major overriding factors) has been examined. Elements have been classified on the basis of their leaching behaviour under different conditions. Results from this study have been used to identify leaching mechanisms. Also the fly ash has been examined under different standard batch leaching tests in order to evaluate and to compare these tests. A Leaching Test Framework has been devised for assessing the stability of trace elements from fly ashes in different environments. This Framework assists in designing more realistic batch leaching tests appropriate to field conditions and can support the development of regulations and protocols for the management and disposal of coal combustion by-products or other solid wastes of environmental concern.     

石河子燃煤电厂重金属排放研究

选取石河子市典型燃煤电厂,对其燃煤烟气重金属排放浓度及飞灰、底渣、脱硫石膏重金属的富集进行定量分析。结果表明,烟气中各重金属排放浓度从高到低依次为Zn、Ni、Cr、Pb、Cu、Hg、Co、Cd、As。各重金属元素在飞灰中的富集程度较高,除Hg、Cd、Ni外,其他重金属元素在飞灰的富集因均值均大于5。其中,As在飞灰的富集因子均值为5.76。研究结果可为石河子重金属污染控制提供基础数据。     

Investigation on chemical species of arsenic, selenium and antimony in fly ash from coal fuel thermal power stations

Investigations of the existing chemical forms and the concentrations of arsenic (As), selenium (Se) and antimony (Sb) in samples of fly ash obtained from six coal-fired power stations in various countries were carried out. The concentration of As was found to vary from 5.4 to 22.3 mg kg(-1), and the most common mode of occurrence of As in the fly ashes is in association with carbonates or Fe-Mn oxides. The concentrations of Se and Sb ranged from 2.3-5.2 and 1.0-3.9 mg kg(-1), respectively. The dominant chemical forms of Se and Sb in the fly ashes were as extractable species. Also, water-soluble As, Se and Sb in the fly ashes were extracted, and the chemical species of As, Se and Sb in the extract determined using HPLC-ICP-MS. This was done as the potential release of soluble As, Se and Sb through leaching of fly ash is of environmental concern. The most abundant form of As in the extract was the low toxicity As(V). The main species of Se was Se(IV), although it was found that the ratio of Se(VI) to Se(IV) in acidic fly ashes is higher than in alkaline fly ash samples. Antimony was mostly present as Sb(III).     

Leaching Characteristics of Fly Ash from Thermal Power Plants of Soma and Tunçbilek, Turkey

Use of lignite in power generation has led to increasing environmental problems associated not only with gaseous emissions but also with the disposal of ash residues. In particular, use of low quality coal with high ash content results in huge quantities of fly ash to be disposed of. The main problem related to fly ash disposal is the heavy metal content of the residue. In this regard, experimental results of numerous studies indicate that toxic trace metals may leach when fly ash contacts water. In this study, fly ash samples obtained from thermal power plants, namely Soma and Tunçbilek, located at the west part of Turkey, were subjected to toxicity tests such as European Committee for standardization (CEN) and toxicity characteristic leaching (TCLP) procedures of the U.S. Environmental Protection Agency (U.S. EPA). The geochemical composition of the tested ash samples from the power plant show variations depending on the coal burned in the plants. Furthermore, the CEN and TCLP extraction results showed variations such that the ash samples were classified as `toxic waste' based on TCLP result whereas they were classified as `non-toxic' wastes based on CEN results, indicating test results are pH dependent.     

Investigation into the relationship between major and minor element contents and particle size and leachability of boron in fly ash from coal fuel thermal power plants

A basic investigation of boron in discharged fly ash by coal fuel thermal power plants in several worldwide locations was carried out. Eight kinds of fly ash sample were prepared from eight coal fuel thermal power plants. Two of the fly ash samples were used to examine the relationship between the concentration of boron in fly ash and the particle size. When the particle size of fly ash is smaller, there is a possibility that it will be released into the air and spread over a wide area in the environment. However, it has become apparent that fly ash of smaller particle size has a higher concentration of boron and a higher enrichment factor. In other fly ash samples, the boron contents were examined and leaching tests were carried out. There is acidic fly ash as well as alkaline fly ash that contains larger amounts of acidic or basic salts. On alkaline fly ash, when the concentration of boron bound to Fe-Mn oxide is low; it has become apparent that leaching boron is increased in a solution with lower pH of approximately 4 which is nearly the pH of acid rain.     

燃油和燃煤电厂排放可吸入颗粒物的物理化学特性

分别对燃烧重油与烟煤两个电厂排放可吸入颗粒物的显微结构、颗粒类型及重金属在可吸入颗粒物中分布特征进行研究.研究表明,燃煤电厂排放可吸入颗粒物的形态都以球形颗粒为主,而燃油电厂排放可吸入颗粒物由一些絮状物和类似于燃煤飞灰中球形颗粒组成.根据可吸入颗粒物的化学组成,发现燃油电厂排放可吸入颗粒物的颗粒类型有硅铝质和钙-硅铝质...     

Determination and evaluation of hexavalent chromium in power plant coal combustion by-products and cost-effective environmental remediation solutions using acid mine drainage

The chromium species leaching from a coal combustion fly ash landfill has been characterized as well as a novel approach to treat leachates rich in hexavalent chromium, Cr(VI), by using another natural waste by-product, acid mine drainage (AMD), has been investigated during this study. It is observed that as much as 8% (approximately 10 microg g(-1) in fly ash) of total chromium is converted to the Cr(VI) species during oxidative combustion of coal and remains in the resulting ash as a stable species, however, it is significantly mobile in water based leaching. Approximately 1.23 +/- 0.01 microg g(-1) of Cr(VI) was found in the landfill leachate from permanent deposits of aged fly ash. This study also confirmed the use of AMD, which often is in close proximity to coal combustion by-product landfills, is an extremely effective and economical remediation option for the elimination of hexavalent chromium in fly ash generated leachate. Speciated isotope dilution mass spectrometry (SIDMS), as described in EPA Method 6800, was used to analytically evaluate and validate the field application of the ferrous iron and chromate chemistry in the remediation of Cr(VI) runoff.     

Speciation of Cr and its leachability in coal by-products from spanish coal combustion plants

This study evaluates the behaviour of total Cr and Cr (VI) during coal combustion in two Spanish power stations. The content and distribution of Cr in the feed coal and combustion wastes was determined and the Cr contents were normalized using enrichment factor indexes. The speciation of Cr in the fly ash fractions from the different hoppers of the electrostatic precipitators was established and the possibility that the Cr (VI) might lixiviate when ashes are disposed of at landfill sites was assessed. Differences in the distribution and behavior of Cr in the two power stations were observed. According to European directive 1999/31/CEE, soluble Cr(VI) in the fly ashes studied would be unlikely to pose an environmental or health risk when the ash is disposed of.     

Effects of leachant temperature and pH on leachability of metals from fly ash. A case study: Can thermal power plant, province of Canakkale, Turkey

Lignite powered electric generation plants result in increasing environmental problems associated with gaseous emissions and the disposal of ash residues. Especially, low quality coals with high ash content cause enormous quantities of both gaseous and solid fly ash emissions. The main problem is related to the disposal of fly ash, which, in many cases, contains heavy metals. It is known that toxic trace metals may leach when fly ash is in contact with water. In this study, fly ash samples obtained from the thermal power plant in the town of Can in Turkey were investigated for leachability of metals under different acidic and temperature conditions. The experimental results show that a decrease in pH of the leachant favors the extraction of metal ions from fly ash. A significant increase in the extraction of arsenic, cadmium, chromium, zinc, lead, mercury, and selenium ions from the ash is attributed to the instability of the mineral phases. These heavy metals concentrations increase with respect to increasing acidic conditions and temperature. Peak concentrations, in general, were found at around 30°C.     

Monitoring the species of arsenic, chromium and nickel in milled coal, bottom ash and fly ash from a pulverized coal-fired power plant in western Canada

The concentration of As, Cr and Ni and their speciation (As3+;5+, Cr3+;6+ and Ni0;2+) in milled coal, bottom ash and ash collected by electrostatic precipitator (ESP) from a coal fired-power plant in western Canada were determined using HGAAS, ICP-AES and XANES. The chemical fractionation of these elements was also determined by a sequential leaching procedure, using deionized water, NH4OAC and HCI as extracting agents. The leachate was analyzed by ICP-AES. Arsenic in the milled coal is mostly associated with organic matter, and 67% of this arsenic is removed by ammonium acetate. This element is totally removed from milled coal after extraction with HCI. Arsenic occurs in both the As3+ and the As5+ oxidation states in the milled coal, while virtually all (>90%) of the arsenic in bottom ash and fly ash appears to be in the less toxic arsenate (As5+) form. Both Ni and Cr in the milled coal are extracted by HCI, indicating that water can mobilize Ni and Cr in an acidic environment. The chromium is leached by water from fly ash as a result of the high pH of the water, which is induced during the leaching. Ammonium acetate removes Ni from bottom ash through an ion exchange process. Chromium in milled coal is present entirely as Cr3+, which is an essential human trace nutrient. The Cr speciation in bottom ash is a more accentuated version of the milled coal and consists mostly of the Cr3+ species. Chromium in fly ash is mostly Cr3+, with significant contamination by stainless-steel from the installation itself.     

Study of heavy metals in some environmental samples

Fuels like coal and rubber are frequently used for brick burning. However, both coal and rubber contain heavy metals. These heavy metals may elutriate in the wake of fly ash or may adsorb or absorb in the product. The present work deals with the analysis of heavy metals in some samples collected from brick burning industries located in the vicinity of a metropolitan city, Peshawar, Pakistan. Samples from raw clay, product, chimney scale and fossil fuel & rubber were collected and leached with acid mixture. The leachates were concentrated and analyzed by atomic absorption spectrophotometer for the determination of chromium (Cr), lead (Pb), cadmium (Cd) and antimony (Sb). It was observed that heavy metals are present in clay, brick and chimney scale. However, significant amount of these metals was observed in chimney scale. It is inferred that such emanations laden with heavy metals are accompanying the stack gases which are being dumped in to the environment. In order to avoid environmental problems, strict environmental regulations shall be enforced and a constant check on these emanations to the environment must be made to ensure clean air act.     

Study on the law of heavy metal leaching in municipal solid waste landfill

Comparative leaching experiments were carried out using leaching medium with different pH to municipal solid waste in the landfill columns in order to investigate the mobility of heavy metals. The leachate pH and oxidation–reduction potential were measured by oxidation–reduction potential analyzer; the contents of heavy metals were measured by inductively coupled plasma mass spectrometry. It is very different in leaching concentrations of heavy metals; the dynamic leaching of heavy metals decreased with the rise of the leaching amount on the whole. Acid leaching medium had definite influence on the leaching of heavy metals in the early landfill, but it had the obvious inhibition effect on the leaching in the middle and late period of landfill; the neutral and alkaline leaching medium are more beneficial to the leaching of heavy metals. Due to the influence of the environment of landfill, the differences of the results in cumulative leaching amount, leaching rate, and leaching intensity of heavy metals are very big. The calculation results of the release rates of heavy metals prove that the orders of the release rates are not identical under different leaching conditions. Acid rain made heavy metals migrate from municipal solid waste to soil and detain in soil more easily; approached neutral and alkaline leaching mediums are more beneficial to leaching of heavy metals in the municipal solid waste and soil with leachate. The field verification of experimental data showed that the law of heavy metal leaching in municipal solid waste revealed by the experiment has a good consistency with the data obtained by municipal solid waste landfill.     

Characterisation of individual aerosol particles on moss surfaces: implications for source apportionment

The size, morphology and chemical composition of 8405 particles on moss surfaces (Hylocomium splendens) was investigated by scanning electron microscopy and energy-dispersive X-ray microanalysis. Two moss samples from three locations in Southern Norway (Alg?rd, Birkeland, Neslandsvatn) and two sampling years (1977 and 2005) each were selected leading to a total of 12 samples investigated. At all three locations, particle deposition decreased substantially with time. The major particle groups encountered include silicates, iron-rich silicates, metal oxides/hydroxides, iron oxides/hydroxides, carbonates, carbon-rich particles, silicate fly ashes, iron-rich silicate fly ashes, and iron oxide fly ashes. Between 1977 and 2005, the relative number abundance of the three fly ash groups decreased substantially from approximately 30-60% to 10-18% for the small particles (equivalent projected area diameter <1 microm), and from 10-35% to 2-9% for large particles with diameters ≥1 microm. This decrease of fly ash particles with time was overlooked in previous papers on atmospheric input of pollutants into ecosystems in Southern Norway. In general, the presence of fly ash particles is ignored in most source apportionment studies based on bulk chemical analysis. Consequently, the geogenic component (crustal component) derived from principal component analysis is overestimated systematically, as it has a similar chemical composition as the fly ash particles. The high abundance of fly ashes demonstrates the need to complement source apportionment based on bulk chemistry by scanning electron microscopy in order to avoid misclassification of this important anthropogenic aerosol component.     

Impact of Fly Ash from Coal-Fired Power Stations in Delhi, with Particular Reference to Metal Contamination

Indraprastha Power Station (IPP Stn) and Rajghat Power House (RPH), owned by Delhi Electric Supply Undertaking, are both coal-fired power stations located on Ring Road in New Delhi. Ash content of the coal used ranges between 38–47%. The ash is collected in electrostatic precipitators which have an efficiency of 99.3% (IPP station), and 99.7% (RPH). There are instances of major dust pollution around the power stations from fly ash dispersal. The main method of disposal of fly ash from the power stations is by mixing with water, the resultant slurry is pumped through pipes to ash disposal ponds. The supernatant from these ponds is discharged into River Yamuna. Field studies have revealed large quantities of fly ash being deposited into the river. Local populations of Eichhornia crassipes have reduced dramatically between 1987–1995, with a marked reduction in the year 1994–1995. Field studies, conducted in January, 1995 have investigated the impact of fly ash dispersal in the Delhi region with particular reference to metal contamination. Elemental concentrations for a range of elements are determined by ICP-AES in fly ash and top soils along four transects from the power stations up to a distance of 8 km. The effects of fly ash leachates from the ash settling ponds on the river are determined by analyzing river overbank soils and vegetation for their elemental contents. It is concluded that fly ash dispersal from the stacks are a source of alkali, alkaline-earth and to some extent heavy metals in soils in the vicinity of the power stations, and enrichment of elements in river overbank soils are a result of discharge of fly ash leachates from ash disposal ponds. However, the impact from both these sources of metal contamination is not large enough to give cause for concern. Marked reduction in populations of Eichhornia crassipes downstream of the river where it receives leachates from the ash disposal ponds are attributed to turbidity of the ash pond leachates and metal toxicity. Elemental enrichment in the floodplain soils, as a result of fly ash particle deposition during monsoons, may enhance the horticultural value of these soils as is shown by a healthy cultivated crop of Brassica juncea.     

Natural attenuation of coal combustion waste in river sediments

The weathering of coal combustion products (CCPs) in a lotic environment was assessed following the Tennessee Valley Authority (Kingston, TN) fly ash release of 2008 into surrounding rivers. Sampled materials included stockpiled ash and sediment collected from 180 to 880 days following the release. Total recoverable concentrations of heavy metals and metalloids in sediment were measured, and percent ash was estimated visually or quantified by particle counts. Arsenic and selenium in sediment were positively correlated with percent ash. For samples collected 180 days after the release, total concentrations of trace elements downstream of the release were greater than reference levels but less than concentrations measured in stockpiled ash. Total concentrations of trace elements remained elevated in ash-laden sediment after almost 2.5 years. A sequential extraction procedure (SEP) was used to speciate selected fractions of arsenic, copper, lead, nickel, and selenium in decreasing order of bioavailability. Concentrations of trace elements in sequentially extracted fractions were one to two orders of magnitude lower than total recoverable trace elements. The bulk of sequentially extractable trace elements was associated with iron-manganese oxides, the least bioavailable fraction of those measured. By 780 days, trace element concentrations in the SEP fractions approached reference concentrations in the more bioavailable water soluble, ion exchangeable, and carbonate-bound fractions. For each trace element, the percentage composition of the bioavailable fractions relative to the total concentration was calculated. These SEP indices were summed and shown to significantly decrease over time. These results document the natural attenuation of leachable trace elements in CCPs in river sediment as a result of the loss of bioavailable trace elements over time.     

燃煤电厂周边大气重金属污染特征及来源解析

为探究燃煤电厂周边大气环境中重金属的污染特征与来源,对广东某山区燃煤电厂周边地区环境和污染源的重金属进行测定,分析其污染特征,采用因子分析法和Pb同位素示踪法对环境中的重金属进行来源解析。结果表明,研究区域室内积尘中重金属浓度水平明显高于土壤重金属,污染空间分布与当地气象条件相关。环境空气TSP中重金属主要来自2个污染源,Cd、Pb、As主要来自电厂燃煤,Ca、Mn、Al、Mg主要来自土壤扬尘。TSP、降尘、积尘样品所含的Pb均与电厂采集的煤、炉渣、粉煤灰样品所含的Pb具有同源性,与其他污染源同源性不明显,说明研究区域大气中Pb污染主要来自电厂燃烧所排放的烟尘,其他污染源影响不大。     

Comparative study of the microstructural and magnetic properties of fly ashes obtained from different thermal power plants in West Bengal, India

This paper deals with the physical nature of the fly ashes obtained from two thermal power plants, situated in West Bengal, India. The fly ash samples are characterized by using comprehensive techniques with an emphasis on their ultrafine nature. The particle sizes of the samples are estimated using scanning electron microcopy (SEM) and found to lie within 0.18–5.90 μm. For morphology and compositional analysis, we also use SEM coupled with energy dispersive X-ray spectrometry. From X-ray study of the fly ashes the nature of conglomeration is seen to be crystalline, and the major components are mullite (Al₆Si₂O₁₃) and quartz (SiO₂). The magnetic measurement of the fly ash samples was carried out by SQUID magnetometer. ⁵⁷Fe Mössbauer spectra are obtained using a conventional constant-acceleration spectrometer with a ⁵⁷Co/Rh Mössbauer source. The hyperfine parameters obtained, in general, support the findings as made from XRD analysis and provide a quantitative measure of different iron ions present in the samples. The paper presents experimental data on the physical aspects of the fly ash samples of the thermal power plants which comprise coarse, fine, and ultrafine magnetic particulate materials and attempts to provide an exhaustive analysis.     

统计学在垃圾焚烧飞灰浸提液重金属检测准确性研究中的应用

为提高复杂基体重金属检测准确性,在使用电感耦合等离子体发射光谱法检测生活垃圾焚烧飞灰浸提液时,进行标准曲线法、标准加入法和内标法3种定量校准方法比对。3种方法报出结果经过加标回收率换算后的样品原值具有明显一致性,使用统计学方差齐性和单因素方差分析验证了该一致性成立,表明内标法的精密度和准确度与标准曲线法、标准加入法无显著性差别。以3种方法样品原值的算数平均值作为样品最佳估计值评价各方法实际报出结果准确性,标准加入法准确性最好;稀释后的样品内标法加标回收率明显优于标准规定,受稀释倍数影响不大,工作效率高,满足HJ 781—2016质控要求,建议可作为该标准的补充;建议批量样品检测时优先采用内标法。3种方法样品原值一致性的验证,有助于执法、科研中对于复杂基体重金属物质含量的准确判断。     

微波消解法测定铅锌冶炼厂废旧除尘布袋及其飞灰中重金属的应用研究

以广东某铅锌冶炼厂的废旧除尘布袋及其布袋上的飞灰为实验材料,以HNO3-H2O2-HF对布袋及飞灰进行微波全量消解,采用BCR三步浸提法提取飞灰中Cu、Zn、Pb、Cr、Ni、Cd 6种重金属,并利用火焰原子吸收仪器检测布袋及飞灰中6种重金属的含量及飞灰中各形态含量。结果表明,铅锌冶炼厂废旧布袋和飞灰中重金属含量较高,远大于《国家土壤环境质量标准》(GB 15168—1995)三级标准值。不同重金属在飞灰中的形态分布差异较大,Ni主要以残渣态和酸可交换态为主,Cu和Pb以残渣态为主,Zn的4种形态分布都较均匀,Cd、Zn潜在的迁移性最强。     

Restoration of fly ash dump through biological interventions

Field experiment on 10 ha area of fly ash dump was conducted to restore and revegetate it using biological interventions, which involves use of organic amendment, selection of suitable plant species along with specialized nitrogen fixing strains of biofertilizer. The results of the study indicated that amendment with farm yard manure at 50 t/ha improved the physical properties of fly ash such as maximum water holding capacity from 40.0 to 62.42% while porosity improved from 56.78 to 58.45%. The nitrogen content was increased by 4.5 times due to addition of nitrogen fixing strains of Bradyrhizobium and Azotobacter species, while phosphate content was increased by 10.0 times due to addition of VAM, which helps in phosphate immobilization. Due to biofertilizer inoculation different microbial groups such as Rhizobium, Azotobacter and VAM spores, which were practically absent in fly ash improved to 7.1 × 10⁷, 9.2 × 10⁷ CFU/g and 35 VAM spores/10 g of fly ash, respectively. Inoculation of biofertilizer and application of FYM helped in reducing the toxicity of heavy metals such as cadmium, copper, nickel and lead which were reduced by 25, 46, 48 and 47%, respectively, due to the increased organic matter content in the fly ash which complexes the heavy metals thereby decreasing the toxicity of metals. Amendment of fly ash with FYM and biofertilizer helped in profuse root development showing 15 times higher growth in Dendrocalamus strictus plant as compared to the control. Thus amendment and biofertilizer application provided better supportive material for anchorage and growth of the plant.