Assessment of respirable dust exposures in an opencast coal mine

All major opencast mining activities produce dust. The major operations that produce dust are drilling, blasting, loading, unloading, and transporting. Dust not only deteriorates the environmental air quality in and around the mining site but also creates serious health hazards. Therefore, assessment of dust levels that arise from various opencast mining operations is required to prevent and minimize the health risks. To achieve this objective, an opencast coal mining area was selected to generate site-specific emission data and collect respirable dust measurement samples. The study covered various mining activities in different locations including overburden loading, stock yard, coal loading, drilling, and coal handling plant. The dust levels were examined to assess miners' exposure to respirable dust in each of the opencast mining areas from 1994 to 2005. The data obtained from the dust measurement studies were evaluated by using analysis of variance (ANOVA) and the Tukey-Kramer procedure. The analyses were performed by using Minitab 14 statistical software. It was concluded that, drilling operations produce higher dust concentration levels and thus, drill operators may have higher incidence of respiratory disorders related to exposure to dust in their work environment.     

Implementing infrared determination of quartz particulates on novel filters for a prototype dust monitor

Research by the National Institute for Occupational Safety and Health (NIOSH) has pursued quartz analysis for the specialized filter assemblies of a new worker-wearable personal dust monitor (PDM). The PDM is a real-time instrument utilizing a tapered element oscillating microbalance (TEOM). Standard fiberglass TEOM filters cannot accommodate the desired P-7 infrared analytical method used by the Mine Safety and Health Administration (MSHA). Novel filter materials were tested with the objective of demonstrating this type of analysis. Low temperature ashing and spectrometric examination were employed, revealing that nylon fiber candidate filters left minimal residual ash and produced no significant spectral interference. Avoiding titanium dioxide in all filter materials proved to be a key requirement. Fine quartz particulates were collected on prototype filters in a Marple chamber, either open-faced or through PDMs during test runs. The filters were then subjected to MSHA P-7 analysis and the spectrometrically based analytical results for quartz mass were compared to reference measurements. Also, PDM instrumental mass readings were compared to filter gravimetric measurements. Results suggest that the P-7 method is adaptable to variations in filter materials and that quartz dust analysis by the P-7 method when utilizing the new ashable PDM filters can have accuracy and precision within 10% and 4%, respectively. This is within the declared 13% accuracy and 7-10% precision of the P-7 method itself. Instrument mass readings had modest positive bias but met NIOSH accuracy criteria. Continued work with specialized PDM filters is merited, as they are a new type of TEOM sample amenable to ashing analysis of particulates.     

Northern Idaho House Dust and Soil Lead Levels Compared to the Bunker Hill Superfund Site

House dust has been identified as a major exposure medium for lead (Pb) in children. High levels of Pb in soil and house dust have been recorded at the Bunker Hill Superfund Site (BHSS) in northern Idaho, an historic mining and smelting district. Soil and dust remediation at the site was required; however, regional background soil and dust Pb levels had not been well characterized. The objective of this survey was to determine background house dust Pb levels and to compare those levels with concentrations, and dust and Pb loading rates measured at the BHSS. Soil and house dust samples were collected in five towns demographically similar to the BHSS but unaffected by the mining industry. The background concentrations and loading rates were significantly lower than those observed at the site. House age was a significant factor affecting background soil and house dust Pb concentrations and loading rates.     

Exposure to inhalable dust and endotoxin among Danish livestock farmers: results from the SUS cohort study

Studies on personal dust and endotoxin concentrations among animal farmers have been either small or limited to a few sectors in their investigations. The present study aimed to provide comparable information on the levels and variability of exposure to personal dust and endotoxin in different types of animal farmers. 507 personal inhalable dust samples were collected from 327 farmers employed in 54 pig, 26 dairy, 3 poultry, and 3 mink farms in Denmark. Measurements in pig and dairy farmers were full-shift and performed during summer and winter, while poultry and mink farmers were monitored during 4 well-defined production stages. The collected samples were measured for dust gravimetrically and analyzed for endotoxin by the Limulus amebocyte lysate assay. Simple statistics and random-effect analysis were used to describe the levels and the variability in measured dust and endotoxin exposure concentrations. Measured inhalable dust levels had an overall geometric mean of 2.5 mg m(-3) (range 相似文献   

Real-time PCR detection of toxigenic Fusarium in airborne and settled grain dust and associations with trichothecene mycotoxins

Inhalation of immunomodulating mycotoxins produced by Fusarium spp. that are commonly found in grain dust may imply health risks for grain farmers. Airborne Fusarium and mycotoxin exposure levels are mainly unknown due to difficulties in identifying Fusarium and mycotoxins in personal aerosol samples. We used a novel real-time PCR method to quantify the fungal trichodiene synthase gene (tri5) and DNA specific to F. langsethiae and F. avenaceum in airborne and settled grain dust, determined the personal inhalant exposure level to toxigenic Fusarium during various activities, and evaluated whether quantitative measurements of Fusarium-DNA could predict trichothecene levels in grain dust. Airborne Fusarium-DNA was detected in personal samples even from short tasks (10-60 min). The median Fusarium-DNA level was significantly higher in settled than in airborne grain dust (p < 0.001), and only the F. langsethiae-DNA levels correlated significantly in settled and airborne dust (r(s) = 0.20, p = 0.003). Both F. langsethiae-DNA and tri5-DNA were associated with HT-2 and T-2 toxins (r(s) = 0.24-0.71, p < 0.05 to p < 00.01) in settled dust, and could thus be suitable as indicators for HT-2 and T-2. The median personal inhalant exposure to specific toxigenic Fusarium spp. was less than 1 genome m(-3), but the exposure ranged from 0-10(5) genomes m(-3). This study is the first to apply real-time PCR on personal samples of inhalable grain dust for the quantification of tri5 and species-specific Fusarium-DNA, which may have potential for risk assessments of inhaled trichothecenes.     

On-filter determination of collected wood dust by diffuse reflectance infrared Fourier-transform spectroscopy (DRIFTS)

A new analytical technique based on DRIFTS spectroscopy has been developed for the specific and sensitive determination of size-fractionated wood dust from 37 mm glass fiber filter samples collected with the Respicon sampler. A translational diffuse reflectance apparatus was modified to accept filter samples by incorporating a special filter holder in the sample stage and a clockwork motor to drive the translational stage during infrared scanning, thus providing an average analysis across the filter face. Filter samples were pre-treated with ethyl acetate to uniformly redeposit dust onto the filter and extract potential chemical interferences. Two absorbance maxima (1251 and 1291 cm(-1)), corresponding to the cellulose content of the wood, were suitable for quantitation of wood dust. Analysis of seven species of wood at 1291 cm(-1) showed an equivalent quantitative response for all species except maple. The response at 1251 cm(-1) was more variable across species but more sensitive for the softwoods. There was a statistically significant effect of particle size on the analytical response, so that analytical standards should be matched to the samples in terms of particle size distribution. Analytical limit of detection was approximately 0.08 mg of wood dust per sample with overall precision of about 6%. Comparison of DRIFTS and gravimetric analyses of 51 pure wood dust samples ranging from about 0.2 to 2 mg yielded a slope of 1.08 and r2 equal to 0.9. Other particulate contaminants common in the industrial wood processing industry showed little or no interference with the determination of wood dust by this method.     

Uranium bioassay and radioactive dust measurements at some uranium processing sites in Egypt--health effects

The safety of radiation workers in the uranium mining industry requires close and continuous monitoring of their working conditions. In this study, external radiation surveillance, radioactive dust monitoring and the bioassay of uranium were carried out in some processing sites. As dust represents one of the most important sources of radiation exposure in mills and mines, dust monitoring and bioassays were performed for a sample of workers on the production lines. The concentration of uranium in air ranged from 22.6 x 10(-7) to 11.1 x 10(-5) Bq cm-3, and the exposure levels ranged from 1 to 80 microSv h-1. Laser fluorimetric determination of uranium in urine samples showed concentrations in the range 8.4-29.2 micrograms L-1. Renal function parameters, such as serum creatinine and urea, and hematological parameters were determined in an attempt to correlate them with radiation exposure and the health status of the workers. Urine specimens collected from workers at the ore crushing and separation site showed elevated concentrations of uranium (up to 29.2 micrograms L-1) and a strong correlation between these concentrations and the registered serum creatinine. The mean uranium excretion in the investigated group was more than 20 times the occupational exposure decision level for urine uranium of 0.8 microgram L-1.     

Advanced REACH Tool (ART): calibration of the mechanistic model

The mechanistic model of the Advanced Reach Tool (ART) provides a relative ranking of exposure levels from different scenarios. The objectives of the calibration described in this paper are threefold: to study whether the mechanistic model scores are accurately ranked in relation to exposure measurements; to enable the mechanistic model to estimate actual exposure levels rather than relative scores; and to provide a method of quantifying model uncertainty. Stringent data quality guidelines were applied to the collated data. Linear mixed effects models were used to evaluate the association between relative ART model scores and measurements. A random scenario and company component of variance were introduced to reflect the model uncertainty. Stratified analyses were conducted for different forms of exposure (abrasive dust, dust, vapours and mists). In total more than 2000 good quality measurements were available for the calibration of the mechanistic model. The calibration showed that after calibration the mechanistic model of ART was able to estimate geometric mean (GM) exposure levels with 90% confidence for a given scenario to lie within a factor between two and six of the measured GM depending upon the form of exposure.     

Biological responses of workplace particles and their association with adverse health effects on miners

Epidemiological research has demonstrated the relationship between exposure to quartz dust and an elevated risk of pneumoconiosis and possible elevated risk of cancer. The current study was designed to evaluate the biological responses of workplace particles containing crystalline silica using an in vitro cell test. Respirable particle samples were sampled from four tin mines, where the standardized mortality ratio (SMR) for pneumoconiosis was 51.6 and SMR for lung cancer was 2.2 in dust-exposed miners. Alveolar macrophages (AM) are considered as the target cells for primary dust effects. The samples were then measured at 15, 30, 60 and 120 microg particle per 10(6) AM for cytoxicity with the release of glucuronidase, lactate dehydrogenase, for reactive oxygen damage with H(2)O(2) release, and for ability to induce fibrosis using the secretion of tumor necrosis factor-alpha (TNF-alpha). Pure quartz (DQ12) and corundum were used as controls. The results showed the samples from tin mines caused a higher cytoxicity when compared to corundum, yet lower when compared to quartz. However, reactive oxygen species release (148-177 nmol/3 x 10(5) AM in high concentration of 120 microg/10(6) AM) induced by the samples were significantly higher than that induced by quartz (57 nmol/3 x 10(5) AM) and corundum (62 nmol/3 x 10(5) AM). Furthermore, particle samples induced higher TNF-alpha secretion than corundum, the samples from Limu tin mine induced much higher TNF-alpha levels than that induced by DQ12 quartz. The results from the in vitro tests help elucidate the degree of hazard of dust particles in tin mines. The in vitro reaction patterns of AM also constitute a powerful tool to monitor biological and pathogenic responses of humans following dust particle exposure.     

Ecotoxicological assessment of acid mine drainage: electrophysiological changes in earthworm (Aporrectodea caliginosa) and aquatic oligochaete (Lumbriculus variegatus)

Ecological health of 15 sites in two mining areas on the West Coast of the South Island, New Zealand, was assessed using a non-invasive electrophysiological technique. The conduction velocity (CV) changes in the medial giant fibres (MGF) of the terrestrial earthworm Aporrectodea caliginosa were measured on days 0, 1, 2, 4, 7, 14, and 21 following exposure to soil and/or sediment from six acid mine drainage (AMD) sites, and aquatic oligochaete Lumbriculus variegatus at 0, 3, 6, and 24 h following exposure to water from 14 AMD sites. The colour of the soil/sediments varied from red-brown to black with pH ranging from 4.46 to 7.37. The colour of AMD water samples varied from clear, black, brown to orange, and the pH ranged from 2.99 to 7.66. The CV decreased progressively in A. caliginosa exposed to most soil and sediment samples from the AMD sites (compared with controls exposed to soil from an organic farm) and this was most evident in measurements taken at 7 days. Based on the CV measurements taken on day 7, sites 3 > 2 > 1 were significantly (P < 0.05) the most toxic to earthworms. The CV of L. variegatus exposed to AMD water sampled from many sites also decreased progressively and this was significantly lower than the controls in the measurements taken at 24 h from sites 3 > 9 > 7 > 11. It is proposed that MGF CV in A. caliginosa and L. variegatus worms can be used as a non-invasive, sensitive, biomarker to monitor the toxicity of AMD sites.     

Interlaboratory evaluation of endotoxin analyses in agricultural dusts--comparison of LAL assay and mass spectrometry

Endotoxin exposure is associated with wheeze and asthma morbidity, while early life exposure may reduce risk of allergy and asthma. Unfortunately, it is difficult to compare endotoxin results from different laboratories and environments. We undertook this study to determine if lipopolysaccharide (LPS) extraction efficiency could account for differences among laboratories. We generated and collected aerosols from chicken and swine barns, and corn processing. We randomly allocated side-by-side filter samples to five laboratories for Limulus assay of endotoxin. Lyophilized aliquots of filter extracts were analyzed for 3-hydroxy fatty acids (3-OHFAs) as a marker of LPS using gas chromatography-mass spectrometry. There were significant differences in endotoxin assay and GC-MS (LPS) results between laboratories for all dust types (p < 0.01). Patterns of differences between labs varied by dust type. Relationships between assay and GC/MS results also depended on dust type. The percentages of individual 3-OHFA chain lengths varied across labs (p < 0.0001) suggesting that each lab recovered a different fraction of the LPS available. The presence of large amounts of particle associated LPS and absence of a freezing thawing cycle were associated with lower correlations between LPS and bioactivity, consistent with an absence of Limulus response to cell-bound endotoxin. These data suggest that extraction methods affect endotoxin measurements. The LAL methods may be most suitable when comparing exposures within similar environments; GC-MS offers additional information helpful in optimizing sample treatment and extraction. GC-MS may be of use when comparing across heterogeneous environments and should be considered for inclusion in future studies of human health outcomes.     

Assessment of public exposure to naturally occurring radioactive materials from mining and mineral processing activities of Tarkwa Goldmine in Ghana

Studies have been carried out in a Goldmine in Ghana to determine the exposure of the public to naturally occurring radioactive materials from processing of gold ore. Direct gamma spectrometry and neutron activation analysis techniques were used to analyse soil, rock, water and dust samples from the mining environment. The mean activity concentrations measured for (238)U, (232)Th and (40)K in the soil/rock samples were 15.2, 26.9 and 157.1 Bq kg(?-?1), respectively. For the water samples, the mean activity concentrations were 0.54 and 0.41 Bq l(?-?1)) and 7.76 Bq l(?-?1) for (226)Ra, (232)Th and (40)K, respectively. The mean activity concentrations measured in the dust samples were 4.90 and 2.75 μBq m(?-?3) for (238)U and (232)Th, respectively. The total annual effective dose to the public was estimated to be 0.69 mSv. The results in this study compared well with typical world average values. The results indicate an insignificant exposure of the public from the activities of the Goldmine.     

Occurrence of perfluorosulfonates and other perfluorochemicals in dust from selected homes in the city of Ottawa, Canada

A series of perfluorinated compounds (PFCs) including perfluorooctane sulfonate (PFOS) and perfluorooctanoic acid (PFOA) have been recently measured in a variety of environmental samples and biological matrices. In order to better understand the human exposure routes of these chemicals, levels of PFOS, PFOA, perfluorobutane sulfonate (PFBS), perfluorohexane sulfonate (PFHS) and perfluorooctane sulfonamide (PFOSA) in house dust samples were investigated. The data revealed a correlation between the concentrations of PFCs and the percentage of carpeting in the house; older houses tended to have less carpeting, hence lower levels of these perfluorinated compounds in their dust.     

New approaches for assessment of occupational exposure to metals using on-site measurements

Traditional assessment of occupational exposure to metals typically involves static or personal aerosol sampling on a membrane filter followed by a laboratory determination of the metal content on the filter sample. These techniques give results with high accuracy and low detection limits. However, they all have a drawback in that, since the samples have to be analysed in a laboratory, the results will usually be obtained days or weeks after the sampling took place. Today there is available a new generation of portable electronic micro-balances and instruments for metal analysis based on X-ray fluorescence. These instruments will make on-site measurements of metal exposure possible, which opens the way for new approaches for assessment of occupational exposure to metals. In combination with high-flow pumps, short-term sampling is possible, which allows monitoring of the exposure variation during a work shift as well as the exposure during individual work tasks of short duration. Screening measurements and emission measurements are other examples of monitoring that are facilitated using on-site determinations. Measure control monitoring can effectively be performed using on-site measurements and is an effective tool in the assessment of workplace improvements. On-site determinations can also form an effective and pedagogic tool showing workers how to perform specific tasks and demonstrating the effectiveness of different measures intended to improve their work environment. Other examples are the assessment of skin exposure using aerosol deposition on pads and screening of contamination using bulk samples.     

Characterization of different road dusts in opencast coal mining areas of India

Dust from haul and transport roads are the major source of air pollution in opencast coal mining areas. Dust generated during mining operations pollutes air which causes different health problems. Various available techniques are implemented in the field to minimize and control dust in mining areas. However, they are not very effective because dust deposited on road surfaces are not removed by these techniques. For effective control of dust in opencast mining areas, it has to be regularly collected from road surfaces and may be converted into solid form, and subsequently can be used as a domestic fuel considering its physicochemical properties. The present paper describes a comparative study of qualitative and quantitative aspects of road dust samples of four coalfields of India. The pH of the dust was found to be in the range of 5.1–7.7. Moisture, ash, volatile matter, fixed carbon, water-holding capacity, bulk density, and specific gravity of dust samples were found to be in the range of 0.5–3.0%, 45–76%, 12.6–20.0%, 10.2–45.3%, 21.17–31.71%, 1.15–1.70, and 1.73–2.30 g cm⁻³, respectively. Observing the overall generation and characteristics of coal dust, it is suggested that coal dust from haul and transport roads of mining areas can be effectively collected and used as domestic fuel.     

Statistical modeling of crystalline silica exposure by trade in the construction industry using a database compiled from the literature

A quantitative determinants-of-exposure analysis of respirable crystalline silica (RCS) levels in the construction industry was performed using a database compiled from an extensive literature review. Statistical models were developed to predict work-shift exposure levels by trade. Monte Carlo simulation was used to recreate exposures derived from summarized measurements which were combined with single measurements for analysis. Modeling was performed using Tobit models within a multimodel inference framework, with year, sampling duration, type of environment, project purpose, project type, sampling strategy and use of exposure controls as potential predictors. 1346 RCS measurements were included in the analysis, of which 318 were non-detects and 228 were simulated from summary statistics. The model containing all the variables explained 22% of total variability. Apart from trade, sampling duration, year and strategy were the most influential predictors of RCS levels. The use of exposure controls was associated with an average decrease of 19% in exposure levels compared to none, and increased concentrations were found for industrial, demolition and renovation projects. Predicted geometric means for year 1999 were the highest for drilling rig operators (0.238 mg m(-3)) and tunnel construction workers (0.224 mg m(-3)), while the estimated exceedance fraction of the ACGIH TLV by trade ranged from 47% to 91%. The predicted geometric means in this study indicated important overexposure compared to the TLV. However, the low proportion of variability explained by the models suggests that the construction trade is only a moderate predictor of work-shift exposure levels. The impact of the different tasks performed during a work shift should also be assessed to provide better management and control of RCS exposure levels on construction sites.     

Particulate Matter Over A Seven Year Period in Urban and Rural Areas Within, Proximal and Far from Mining and Power Station Operations in Greece

Lignite mining operations and lignite-fired power stations result in major particulate pollution (fly ash and fugitive dust) problems in the areas surrounding these activities. The problem is more complicated, especially, for urban areas located not far from these activities, due to additional contribution from the urban pollution sources. Knowledge of the distribution of airborne particulate matter into size fraction has become an increasing area of focus when examining the effects of particulate pollution. On the other hand, airborne particle concentration measurements are useful in order to assess the air pollution levels based on national and international air quality standards. These measurements are also necessary for developing air pollutants control strategies or for evaluating the effectiveness of these strategies, especially, for long periods. In this study an attempt is made in order to investigate the particle size distribution of fly ash and fugitive dust in a heavy industrialized (mining and power stations operations) area with complex terrain in the northwestern part of Greece. Parallel total suspended particulates (TSP) and particulate matter with an aerodynamic diameter less than 10 μm (PM10) concentrations are analyzed. These measurements gathered from thirteen monitoring stations located in the greater area of interest. Spatial, temporal variation and trend are analyzed over the last seven years. Furthermore, the geographical variation of PM10 – TSP correlation and PM10/TSP ratio are investigated and compared to those in the literature. The analysis has indicated that a complex system of sources and meteorological conditions modulate the particulate pollution of the examined area.     

Passive airborne dust sampling to assess mite antigen exposure in farming environments

The aim of this study was to estimate mite antigen exposure in farming environments by passive sampling of airborne dust. Antigen concentrations were measured with enzyme immunoassays specific for three storage mites (SM): Acarus siro, Lepidoglyphus destructor, Tyrophagus putrescentiae and the house dust mite (HDM) Dermatophagoides pteronyssinus. Dust samples were collected with electrostatic dust fall collectors (EDCs) in three different areas of cattle farms. EDCs were placed in cow stables (working area), in changing rooms (transit area) and in different rooms of farmer dwellings (living area). Mite concentrations in the living area of farm homes were compared to those of urban homes. In dust samples from stables, antigens of all four mite species could be detected. The highest exposure level was to L. destructor (median 56.7 μg/m(2)), the lowest to A. siro (median 14.4 μg/m(2)). Mite concentrations of different species showed no correlation within the cow stables. In comparison to stables, the median mite concentrations in farm homes were significantly lower, ranging from below the detection limit to 1.5 μg/m(2). Antigens of SM were predominantly found in changing rooms and kitchens, and HDM antigens were mainly detected in bedrooms. Antigens of all mites were measured the least often in living rooms. T. putrescentiae was the most prevalent mite in all room types, and the exposure levels correlated strongly between different rooms. The number of SM positive samples in farm homes was considerably higher than in urban homes, while the percentage of HDM positive samples did not differ significantly.     

Validation of the inhalable dust algorithm of the Advanced REACH Tool using a dataset from the pharmaceutical industry

As it is often difficult to obtain sufficient numbers of measurements to adequately characterise exposure levels, occupational exposure models may be useful tools in the exposure assessment process. This study aims to refine and validate the inhalable dust algorithm of the Advanced REACH Tool (ART) to predict airborne exposure of workers in the pharmaceutical industry. The ART was refined to reflect pharmaceutical situations. Largely task based workplace exposure data (n = 192) were collated from a multinational pharmaceutical company with exposure levels ranging from 5 × 10(-5) to 12 mg m(-3). Bias, relative bias and uncertainty around geometric mean exposure estimates were calculated for 16 exposure scenarios. For 12 of the 16 scenarios the ART geometric mean exposure estimates were lower than measured exposure levels with on average, a one-third underestimation of exposure (relative bias -32%). For 75% of the scenarios the exposure estimates were, within the 90% uncertainty factor of 4.4, as reported for the original calibration study, which may indicate more uncertainty in the ART estimates in this industry. While the uncertainty was higher than expected this is likely due to the limited number of measurements per scenario, which were largely derived from single premises.