DNAPL remediation with in situ chemical oxidation using potassium permanganate. Part I. Mineralogy of Mn oxide and its dissolution in organic acids

Previous studies on in situ chemical oxidation of trichloroethylene (TCE) with potassium permanganate indicated that the solid reaction product, Mn oxide, could reduce the permeability of the porous medium and impact the success of dense non-aqueous phase liquid (DNAPL) removal. In order to address the issue of permeability reduction caused by precipitation, this study investigated the mineralogy of Mn oxides and the possibilities of removing the solid precipitates by dissolution. The solid reaction product from the oxidation of TCE by permanganate is semi-amorphous potassium-rich birnessite, which has a layered mineral structure with an interlayer spacing of 7.3 A. The chemical formula is K(0.854)Mn(1.786)O(4).1.55H(2)O. It has a relatively small specific surface area at 23.6+/-0.82 m(2)/g. Its point of zero charge (pzc) was measured as 3.7+/-0.4. This birnessite is a relatively active species and could participate in various reactions with existing organic and inorganic matter. The dissolution kinetics of Mn oxide was evaluated in batch experiments using solutions of citric acid, oxalic acid, and ethylenediaminetetraacetic acid (EDTA). Initial dissolution rates were determined to be 0.126 mM/m(2)/h for citric acid, 1.35 mM/m(2)/h for oxalic acid, and 5.176 mM/m(2)/h for EDTA. These rates compare with 0.0025 mM/m(2)/h for nitric acid at pH=2. Organic acids dissolve Mn oxide quickly. Reaction rates increase with acid concentration, as tested with citric acid. The dissolution mechanism likely involves proton and ligand-promoted dissolution and reductive dissolution. Citric and oxalic acid can induce ligand-promoted dissolution, while EDTA can induce ligand-promoted and reductive dissolutions. At low pH, proton-promoted dissolution seems to occur with all the acids tested, but this process is not dominant. Reductive dissolution appears to be the most effective process in dissolving the solid, followed by ligand-promoted dissolution. These experiments indicate the significant potential in using these organic acids to remove precipitates formed during the oxidation reaction.     

Photodegradation of alachlor with the TiO(2) film immobilised on the glass tube in aqueous solution

Alachlor photodegradation was performed using TiO(2), which was synthesized by a modified sol-gel method. The thickness of a TiO(2) film immobilised by a 5-time dip-coating was 174 nm and the average diameter of TiO(2) particles was about 10-15 nm in SEM images. The crystal structure of a TiO(2) film calcinated at 300 degrees C for 1 h was observed as a typical anatase type. The stability of a TiO(2) film by a modified sol-gel method was 4% better than TiO(2) by a typical sol-gel method.The removal rate of alachlor with both Fe(3+) and UV radiation in the absence of TiO(2) was 0.28 mg/l/h in 10 h and the removal rate of alachlor with Fe(3+)/UV in the presence of TiO(2) was 0.32 g/l/h, which was higher by 14% than that with Fe(3+)/UV system. TOC concentration during the alachlor degradation with both TiO(2) and UV radiation in the absence of added Fe(3+) decreased from 100%, through 81% and 51%, to 44% with time elapses of 4, 8, and 10 h, respectively, while TOC concentration with both added Fe(3+) and UV radiation in the absence of TiO(2) decreased from 100% to 70% in 10 h.     

Performance of photocatalytic reactors using immobilized TiO2 film for the degradation of phenol and methylene blue dye present in water stream

TiO2 thin film photocatalyst was successfully synthesized and immobilized on glass reactor tube using sol-gel method. The synthesized TiO2 coating was transparent, which enabled the penetration of ultra-violet (UV) light to the catalyst surface. Two photocatalytic reactors with different operating modes were tested: (a) tubular photocatalytic reactor with re-circulation mode and (b) batch photocatalytic reactor. A new proposed TiO2 synthesized film formulation of 1 titanium isopropoxide: 8 isopropanol: 3 acetyl acetone: 1.1 H2O: 0.05 acetic acid (in molar ratio) gave excellent photocatalytic activity for degradation of phenol and methylene blue dye present in the water. The half-life time, t1/2 of photocatalytic degradation of phenol was 56 min at the initial phenol concentration of 1000 microM in the batch reactor. In the tubular photocatalytic reactor, 5 re-circulation passes with residence time of 2.2 min (single pass) degraded 50% of 40-microM methylene blue dye. Initial phenol concentration, presence of hydrogen peroxide, presence of air bubbling and stirring speed as the process variables were studied in the batch reactor. Initial methylene blue concentration, pH value, light intensity and reaction temperature were studied as the process variables in the tubular reactor. The synthesized TiO2 thin film was characterized using SEM, XRD and EDX analysis. A comparative performance between the synthesized TiO2 thin film and commercial TiO2 particles (99% anatase) was evaluated under the same experimental conditions. The TiO2 film was equally active as the TiO2 powder catalyst.     

Zr-Fe双组分复合除砷吸附剂的优化制备及性能评价

实验发现,铁氧化物或铁的羟基氧化物对As(V)有较好的吸附性能,而锆氧化物或锆水合氧化物则对As(Ⅲ)有优异的吸附选择性,但其使用的pH通常要在9的条件下。通过简单的共沉淀法制备了Zr-Fe双组分复合吸附剂,在制备过程中通过优化制备条件如:沉淀剂浓度、金属离子总浓度、金属离子配比、反应温度、反应时间及吸附剂价格等因素,最终合成出了对As(V)和As(Ⅲ)都具有良好吸附能力的吸附剂。这种吸附剂在中性条件下对As(V)和As(Ⅲ)的最大吸附量为62 mg/g和118 mg/g。     

Photoelectrocatalytic degradation of 4-chlorophenol and oxalic acid on titanium dioxide electrodes

Photocatalytically active thin TiO(2) films were produced by spin-coating or dip-coating an alkoxy precursor onto a transparent conducting electrode substrate and by thermal oxidation of titanium metal. The thin films were used to study the photoelectrocatalytic or photoelectrochemical degradation of oxalic acid and 4-chlorophenol (4-CP) under near UV (monochromatic, 365 nm) light irradiation. Degradation was monitored by a variety of methods. In the course of oxalic acid degradation, CO(2) formation accounted for up to 100% of the total organic carbon degradation for medium starting concentrations; for the degradation of 4-CP, less CO(2) was detected due to the higher number of oxidation steps, i.e. intermediates. Incident-photon-to-current conversion efficiency, educt degradation and product formation as well as Faradaic efficiencies were calculated for the degradation experiments. Quantum yields and Faradaic efficiencies were found to be strongly dependent on concentration, with maximum values (quantum yield) around 1 for the highest concentrations of oxalic acid.     

Preparation of a titanium dioxide photocatalyst codoped with cerium and iodine and its performance in the degradation of oxalic acid

A novel class of visible light-activated photocatalysts was prepared by codoping TiO(2) with cerium and iodine (Ce-I-TiO(2)). The particles were characterized using the Brunauer-Emmett-Teller method, X-ray diffraction, scanning electron microscopy, X-ray photoelectron spectroscopy and UV-Visible light absorption. Particles of Ce-I-TiO(2) had greater photoabsorption in the 400-800 nm wavelength range than iodine-doped TiO(2) (I-TiO(2)). The effects on the photocatalytic degradation of oxalic acid under visible light or UV-Visible light irradiation were investigated. The photocatalytic activity of Ce-I-TiO(2) calcined at 673 K was significantly higher than that of Ce-I-TiO(2) calcined at 773 K and I-TiO(2) calcined at 673 K in aqueous oxalic acid solution under visible light or UV-Visible light irradiation. Under visible light irradiation, oxalic acid was first adsorbed on the surface of the catalysts rather than reacted with free radicals in the bulk solution, and then oxidized by (·)OH(ads) to CO(2), which was verified by studying the effects of nitrogen purging and scavengers, as well as by gas chromatography/mass spectrometry.     

负载型Mn-Ce／TiO2催化剂的制备及其低温脱硝活性

以成型TiO2作为载体，通过浸渍法制备了Mn-Ce／TiO2低温SCR催化剂，并系统研究了制备方法、煅烧条件、活性组分担载量、Mn含量等参数对催化剂催化还原NO性能的影响。结果表明，煅烧温度的升高会促使活性组分结晶度的提高，从而引起催化活性的降低，在500℃和600℃下所得Mn-Ce／TiO2催化剂活性组分为无定型态，表现出较高的脱硝活性。活性组分担载量的增加有利于催化活性的提高。Mn含量对Mn-Ce／TiO2催化剂的活性有较大影响，当Mn／（Mn＋Ce）摩尔比为40％和85％时，催化剂活性最高。     

Biodegradability and toxicity assessment of trans-chlordane photochemical treatment

The removal of trans-chlordane (C(10)H(6)Cl(8)) from aqueous solutions was studied using UV, UV/H(2)O(2), UV/H(2)O(2)/Fe(2+), UV/TiO(2), or UV/TiO(2)/H(2)O(2) treatment using either UV/Vis blue lamps or UVC lamps (254 nm). H(2)O(2), FeSO(4) and TiO(2) were added at 1700, 456, and 2500 mgL(-1), respectively. trans-Chlordane was not significantly removed in non-irradiated controls and in samples irradiated with UV/Vis. It was also not removed in the absence of surfactant Triton X-114 added at 250 mgL(-1). In the presence of the surfactant, trans-chlordane concentration was reduced by 95-100% after 48 h of UVC and UVC/H(2)O(2) treatments and 70-80% after UVC/H(2)O(2)/Fe(2+), UVC/TiO(2) and UVC/H(2)O(2)/TiO(2) treatments. Based on these results, UVC, UVC/H(2)O(2) and UVC/TiO(2) treatments were further investigated. UVC treatment supported the highest pollutant removal (100% in 48 h), dechlorination efficiency (81% in 48 h), and detoxification to Lepidium sativum seed germination and activated sludge respiration although irradiated samples remained toxic to Chlorella vulgaris. Biodegradation of the UVC irradiated samples removed the source of algae toxicity but this could not be clearly attributed to the removal of trans-chlordane photoproducts because the surfactant interfered with the chemical and biological assays. Evidence was found that trans-chlordane was photodegraded through photolysis causing its successive dechlorination. trans-Chlordane removal was well described by a first order kinetic model at a rate of 0.21±0.01h(-1) at the 95% confidence interval.     

B,N和Ce共掺杂TiO2催化剂光催化活性研究

采用溶胶-凝胶法制备出B,N和Ce共掺杂TiO2光催化剂,并用XRD、SEM等表征了其结构特征。以酸性大红染料溶液的光催化降解为探针反应,考察了制备条件对共掺杂TiO2催化剂活性的影响。结果表明,在400℃,当B,N和Ce的原子比为1∶2∶0.1,焙烧3 h时,光催化剂活性最大,大红染料的降解率达到98%。     

Photocatalytic oxidation of NOx using composite sheets containing TiO2 and a metal compound

The photocatalytic oxidation of nitrogen oxides (NO(x)) over titanium dioxide (TiO(2)) sheets containing metal compounds (MCs) had been studied. Calcium oxide (CaO), magnesium oxide (MgO), calcium carbonate (CaCO(3)), aluminium oxide (Al(2)O(3)) and ferric oxide (Fe(2)O(3)) were used as MCs. Al(2)O(3) and Fe(2)O(3) added to the TiO(2) sheet did not affect the photooxidation of nitrogen oxides (NO(x)). The CaO sheet treated with TiO(2) sol had the greatest efficiency as a NO(x) remover under UV irradiation. It is believed that CaO has a high adsorptivity for nitrogen dioxide (NO(2)) and nitric acid (HNO(3)). The amount of NO(x) removed by a TiO(2) sheet including MC showed a tendency to increase with increasing pH of the MC suspension, i.e. there is a good correlation between the alkalinity of the MC and the retention of NO(2) and HNO(3).     

微乳液法合成掺硫纳米TiO_2及其光催化性能研究

以钛酸四丁酯为钛源,硫脲为掺硫前驱物,采用聚乙二醇辛基苯基醚（Triton X-100）/正己醇/环己烷/氨水的微乳液体系合成了掺硫的纳米TiO2粉体;对其结构进行了表征,以甲基橙为目标降解物考察了其光催化性能。烧结温度通过影响TiO2的晶型转变和颗粒尺寸来影响其光催化性能,随着烧结温度的升高,TiO2的光催化性能先是提高,然后迅速降低;在600℃烧结2 h时催化剂的降解性能达到最佳。掺杂硫可提高TiO2的光催化活性,随着掺杂量的增加,催化剂对甲基橙的降解率先快速增加然后缓慢降低,当掺杂量为S/Ti（摩尔比）=0.01∶1时TiO2的光催化降解效果最好。催化剂在用量较小时迅速提高TiO2的光催化降解性能,而后随着用量的增大反而降低,当催化剂用量为1.5 g/L时,对甲基橙的降解效果最好。     

Effects of acidifying reagents on microwave treatment of dairy manure

Dairy manure, acidified using organic acids (acetic, oxalic, and citric acid) were treated with microwave enhanced advanced oxidation process (MW/H₂O₂-AOP). The effect of a mixture of oxalic acid and commonly used mineral acids (sulfuric and hydrochloric acid) on MW/H₂O₂-AOP was also examined. Substantial amounts of phosphorus were released under MW/H₂O₂-AOP, regardless of organic acid or mineral acid used. All three organic acids were good acidifying reagents; however, only oxalic acid could remove free calcium ion in the solution, and improve settleability of dairy manure. The MW/H₂O₂-AOP and calcium removal process could be combined into a single-stage process, which could release phosphate, solubilize solids and remove calcium from dairy manure at the same time. A mixture of oxalic acid and mineral acid produced the maximum volume of clear supernatant and had an ideal molar ratio of calcium to magnesium for effective struvite (magnesium ammonium phosphate) crystallization process. A single-stage MW/H₂O₂-AOP would simplify the process and reduce mineral acid consumption compared to a two-stage operation. The results of a pilot scale study demonstrate that MW/H₂O₂-AOP is effective in treating manure and recovering resource from dairy farms.     

Photocatalytic production of hydrogen in single component and mixture systems of electron donors and monitoring adsorption of donors by in situ infrared spectroscopy

The photocatalytic production of hydrogen using aqueous Pt/TiO2 suspension has been investigated in single component and mixture systems of electron donors (pollutants). The reaction systems consisted of oxalic acid, formic acid and formaldehyde, respectively. The adsorption of these donors on TiO2 was also monitored by in situ attenuated total reflection infrared spectroscopy (ATRIR). In the single component systems, the efficiency order of electron donors is as follows: H2C2O4 > HCOOH > HCHO. The order is consistent with the order of adsorption affinity of the electron donors on TiO2 determined by ATRIR, which suggests a link between the strength of surface interaction and the efficiency of photocatalytic hydrogen evolution. In the binary mixture systems, competitive inhibition kinetics is observed. When a donor adsorbed strongly on TiO2 in a state of saturated adsorption in a binary system, the overall rate of the hydrogen evolution is consistent with that of decomposition of the donor, and the system can be treated as a single component system.     

聚硅基复合氯化铁絮凝剂的制备及其在采油废水处理中的应用

采用硅酸钠制备聚硅酸,探讨了活化pH、活化剂、硅酸钠浓度(以SiO_2质量分数计)及聚合温度等因素对聚硅酸稳定性的影响.利用聚硅酸及氯化铁制备聚硅基复合氯化铁(PSiF),并通过正交试验分析了活化pH、Si/Fe(摩尔比)、OH/Fe(摩尔比)、制备时间对PSiF絮凝性能的影响.综合考虑絮凝性能、稳定性以及经济性等因素,确定PSiF适宜的制备条件为SiO_2质量分数2%～3%;活化pH为2～3;Si/Fe为0.50～0.75;OH/Fe为0.50～0.75;制备时间为0.5 h;聚合温度低于25℃.对比PSiF、PAC、FeCl_3对采油废水的处理效果,PSiF除浊、除COD效果以及经济性最好,是一种应用前景广阔的新型絮凝剂.     

碘掺杂Ti02可见光光催化性能研究

在低于100℃温度条件下，采用溶胶一凝胶法以钛酸正丁酯为钛源，碘酸钾为碘源，制备了I掺杂纳米TiO2催化剂（I-TiO2），运用x-射线衍射（XRD）、透射电镜（TEM）及x-射线光电子能谱（XPS）等对催化剂进行表征，结果表明，TiO2及I-TiO2催化剂均为锐钛矿，I吸附并包裹在TiO2表面或以间隙进入的形式存在，并未进入TiO2晶格。通过在可见光照射下（A〉420nm）以罗丹明B（RhodamineB，RhB）的光催化降解为探针反应研究了在不同条件下制备催化剂的催化性能，结果表明，掺杂比为n1：n^ti=0．05：l，焙烧温度为400℃，降解介质条件pH=7时，l-TiO2光催化活性明显优于未掺杂的TiO2。光催化降解过程通过红外光谱（IR），总有机碳（TOC）跟踪测定，比较了TiO2掺杂前后降解RhB和对氯苯酚（4-CP）的光催化特性差异；同时采用苯甲酸荧光光度法跟踪测定体系中的氧化物种，表明在可见光下，I-TiO2光催化体系中产生·OH高活性氧化物种从而氧化降解目标化合物。     

利用白云石回收污泥厌氧消化液中的磷

为经济有效地从污泥厌氧消化液中回收磷,构建了以白云石提供钙镁源的磷回收方法,探讨了磷回收的工艺条件与效果。通过盐酸酸化厌氧消化液以降低其碳酸盐含量,同时利用白云石溶于冷稀盐酸的特性使其钙镁缓慢释放到酸化的厌氧消化液中形成第一步磷回收体系,考察体系酸化pH、白云石与厌氧消化液的固液比以及反应pH对白云石的钙镁释放和磷回收效果的影响;第一步磷回收后的上清液为第二步厌氧消化液磷回收提供钙镁源,研究投加钙磷摩尔比对磷回收效果的影响。实验结果表明,当固液比为5.0时,在酸化pH为4.0～4.5且酸化溶出时间为10 h以及反应pH为9.0的条件下,第一步磷回收产物以磷酸钙盐沉淀为主,厌氧消化液磷回收率及回收产物含磷率（以P2O5计）分别达到99.43%和38.49%;第一步磷回收后的上清液按一定的钙磷摩尔比投加到酸化后的厌氧消化液中进行第二步磷回收,当投加钙磷摩尔比为0.20时,在反应pH为9.0的条件下,回收产物同时含有磷酸钙盐和磷酸铵镁,厌氧消化液中氮、磷回收率分别达到13.19%和90.90%,回收产物氮、磷含量（以P2O5计）分别为0.26%和39.58%;经XRD、XRF、ICP及SEM等分析表征,2步磷回收的产物以磷酸钙盐和磷酸铵镁为主要成分,杂质少。研究表明,利用白云石为钙镁源,通过分别构建不同的磷回收体系可以分步从污泥厌氧消化液中经济有效地回收磷,且磷回收率和回收产物含磷率高。     

Adsorption of microcystin-LR from water with iron oxide nanoparticles

Adsorption of microcystin-LR (MC-LR) from water using iron oxide (alpha-Fe2O3) nanoparticles was investigated in this study. Adsorption of MC-LR adsorption was well-described by a pseudo second order kinetics model and Freundlich and Langmuir isotherm equations at 15 to 35 degrees C. Thermodynamic analysis showed that the Gibbs free energy was negative, whereas standard enthalpy and entropy changes were positive at this temperature range. These findings suggest that the adsorption of MC-LR on iron oxide nanoparticles was spontaneous and endothermic. The effects of initial pH, inorganic cations, and competing compounds with carboxyl groups on absorption of MC-LR were also evaluated. Typically, adsorption efficiency decreased with increasing pH from 2 to 11. Sodium ions did not appear to significantly affect MC-LR adsorption, whereas calcium ions slightly enhanced the MC-LR adsorption capacity of the iron oxide nanoparticles. Moreover, the inhibiting effect of competing organic compounds was increased with increasing numbers of carboxyl groups, as follows: citric acid (3)>oxalic acid (2)>benzoic acid (1).     

A study on production of biodiesel using a novel solid oxide catalyst derived from waste

The issues of energy security, dwindling supply and inflating price of fossil fuel have shifted the global focus towards fuel of renewable origin. Biodiesel, having renewable origin, has exhibited great potential as substitute for fossil fuels. The most common route of biodiesel production is through transesterification of vegetable oil in presence of homogeneous acid or base or solid oxide catalyst. But, the economics of biodiesel is not competitive with respect to fossil fuel due to high cost of production. The vegetable oil waste is a potential alternative for biodiesel production, particularly when disposal of used vegetable oil has been restricted in several countries. The present study evaluates the efficacy of a low-cost solid oxide catalyst derived from eggshell (a food waste) in transesterification of vegetable oil and simulated waste vegetable oil (SWVO). The impact of thermal treatment of vegetable oil (to simulate frying operation) on transesterification using eggshell-derived solid oxide catalyst (ESSO catalyst) was also evaluated along with the effect of varying reaction parameters. The study reported that around 90 % biodiesel yield was obtained with vegetable oil at methanol/oil molar ratio of 18:1 in 3 h reaction time using 10 % ESSO catalyst. The biodiesel produced with ESSO catalyst from SWVO, thermally treated at 150 °C for 24 h, was found to conform with the biodiesel standard, but the yield was 5 % lower compared to that of the untreated oil. The utilization of waste vegetable oil along with waste eggshell as catalyst is significant for improving the overall economics of the biodiesel in the current market. The utilization of waste for societal benefit with the essence of sustainable development is the novelty of this work.     

以红薯浸泡液为碳源的生物反硝化

为选择低碳氮比污水生物脱氮中合适的碳源,以搅拌罐浸泡淀粉类物质释放碳源,在确定利用红薯浸泡液为碳源后,以浸没式生物滤池为反应器进行生物反硝化实验。实验结果表明:20 g红薯置于2 L自来水中,采用250 r/m in的搅拌速度,搅拌频率为每搅拌3 h停1 h,2 d后得到的浸泡液COD浓度平均为5 921 mg/L,最高可超过7 000 mg/L;将此红薯浸泡液和污水以1∶50的流量比例,采用分别投加的方式进入反应器,污水中总氮、硝酸盐氮、亚硝酸盐氮及氨氮的平均去除率分别为88.6%、91.6%、88.2%和54.8%,出水COD平均在30 mg/L以下;在红薯浸泡液COD浓度为5 700 mg/L左右时,进水中亚硝酸盐氮浓度与硝酸盐氮浓度比为3∶2时总氮去除率为95.3%,当该比例为2∶3时总氮去除率为88.2%。研究表明,红薯浸泡液是一种经济合适的碳源,采用红薯浸泡液作为低碳氮比污水生物处理中反硝化的碳源是可行的。     

Effects of CH4 and CO on the reduction of nitric oxide to nitrogen in a discharge reactor

Additives are often added to enhance the efficiency of NO removal. This study uses a radio frequency (rf) discharge to consider the effect of added CH4 and CO to simulated NO/N2/O2/H2O mixtures on the elevation of NO conversion and the reduction of NO into N2. The enhancement levels of NO conversion when using various additives were found to be in this order: +CH4 > +CO > no additive. NO conversion reached 99.3%, 86.2%, and 77.6% when adding CH4, CO, and without additive, respectively, at inlet additive/NO molar ratio (R) = 5 and at 120 W. Moreover, the fraction of total N atoms converted from NO into N2 (FN2) was very high, reaching 99.4% and 99.5% when adding CH4 and CO, respectively, at R = 1 and at 120 W. The better operating conditions are using CH4 as the additive at R > or = 1 and a power of > 60 W to reach a higher NO conversion with a higher FN2. However, it should be noted that this rf plasma approach is not practical at this stage because of its relative low pressure.