硼掺杂CeO2/TiO2光催化剂的制备及其活性研究

在三氯化钛和钛酸丁酯水解过程中引入硼酸、硝酸铈,制备了具有可见光活性的硼(B)掺杂CeO₂/TiO₂复合氧化物光催化剂,采用XRD、DRS、XPS等手段进行表征,以偶氮染料酸性红B为模型污染物评估了催化活性.结果表明,硝酸铈加入量影响催化剂的吸收带边,随用量增加,吸收带边红移至481nm(Ce/Ti=1.0,摩尔比),继续增加用量,吸收带边轻微蓝移.催化剂晶相组成与焙烧温度有关,500℃时焙烧样品主要由立方晶型CeO₂和锐钛矿TiO₂组成,焙烧温度高于700℃时,TiO₂转化为金红石型,CeO₂则无显著变化.随焙烧温度升高,催化剂吸收带边明显蓝移,综合考虑催化剂稳定性和太阳能利用,认为500℃焙烧较为合适.B1s XPS显示仅有少量B原子进入复合氧化物晶格取代了氧原子,主要以B₂O₃形式存在.酸性红B降解试验显示B掺杂CeO₂/TiO₂可以提高TiO₂的催化活性,紫外光辐射10min最高可使96.0%的酸性红B分解,且反应彻底,表现出较强的氧化能力,但Ce/Ti>0.5(摩尔比)时催化活性显著下降.     

溴代甲烷在SO42-/TiO2上的光催化降解

采用溶胶-凝胶法制备了SO₄^2-/TiO₂催化剂,运用XRD、BET比表面测定,FTIR等技术对催化剂进行了表征,并在微型常压连续反应装置上进行CH₃Br光催化反应性能考察.结果表明,SO₄^2-引入TiO₂体系使得催化剂的结构和光催化性能得到显著改善.SO₄^2-负载量为9%,烧结温度为450℃时,SO₄^2-/TiO₂催化剂的光催化活性最高;SO₄^2-/TiO₂催化剂对反应物料中的水汽有很好的耐受性;当反应温度低于85℃时,提高反应温度,有利于改善对CH₃Br的光催化反应活性,表观活化能约为19.6kJ·mol^-1,反应温度在85℃～105℃区间时,CH3Br的光催化降解表观活化能为0.     

Preparation, characterization, and photocatalytic activities of boron- and cerium-codoped TiO2

Boron- and cerium-codoped TiO2 photocatalysts were synthesized using modified sol-gel reaction process and characterized by X- ray diffraction （XRD）, X-ray photoelectron spectroscopy （XPS）, particle size distribution （PSD）, diffuse reflectance spectra （DRS）, and Brunauer-Emmett-Teller （BET）. The photocatalytic activities were evaluated by monitoring the degradation of dye Acid Red B （ARB）. The results showed that the prepared photocatalysts were mixed oxides mainly consisting of titania, ceria, and boron oxide. The structure of TiO2 could be transformed from amorphous to anatase and then to rutile by increasing calcination temperature; the transformation being accompanied by the growth of particle size without any obvious change in phase structure of CeO2. The XPS of B1.6Ce1.0-TiO2 prepared at 500℃ showed that a few boron atoms were incorporated into titania and ceria lattice, whereas others existed as B2O3. Cerium ions existed in two states, Ce^3＋ and Ce^4＋, and the atomic ratio of Ce^3＋/Ce^4＋ was 1.86. When boron and cerium were doped, the UV-Vis adsorption band wavelength showed an obvious shift toward the visible range （〈526 nm）. As the atomic ratio of Ce/Ti increased to 1.0, the absorbance edge wavelength increased to 481 nm. The absorbance edge wavelength decreased for higher cerium doping levels （Ce/Ti=2.0）. The particles size ranged from 122 to 255 nm with a domain at 168 nm （39.4%）. The degradation of ARB dye indicated that the photocatalytic activities of boron- and cerium-codoped TiO2 were much higher than those of P25 （a standard TiO2 powder）. The activities increased as the boron doping increased, whereas decreased when the Ce/Ti atomic ratio was greater than 0.5. The optimum atomic ratio of B/Ti and Ce/Ti was 1.6 and 0.5, respectively.     

低温燃烧合成纳米Ni掺杂TiO2光催化剂的表征及活性研究

采用低温燃烧合成法制备了Ni掺杂TiO₂光催化剂,通过紫外-可见漫反射光谱(UV-Vis DRS)、X射线粉末衍射(XRD)、激光散射、热重-差示扫描量热分析(TG-DSC)等方法对催化剂的光吸收特性、晶相组成、粒度分布、升温过程中化学变化等进行了表征,以亚甲基蓝为模型污染物考察了催化剂在可见光下的光催化活性.结果表明,相对P25而言,Ni掺杂TiO₂的光吸收带边红移,当Ni/Ti原子比为0.4时,催化剂的带隙宽度为2.3eV,对应的吸收带边为564nm;催化剂晶型以锐钛矿TiO₂为主,随Ni掺杂量增大,NiTiO₃比例升高;催化剂粒径主要分布在50～150nm之间,占总量的96.9%;升温过程中催化剂在445.2℃发生晶型转化,出现锐钛矿和NiTiO₃晶体.催化剂显示出较高的催化活性,在可见光作用150min后最高可使93.9%的亚甲基蓝分解,活性高于P25.     

电化学还原-氧化工艺降解4-氯酚的毒性研究

采用紫外光还原法制备了Pd-Fe/石墨烯催化阴极,并以Ti/IrO_2/RuO_2为阳极,构成三电极体系(双阴极)和两电极体系(单阴极)的电化学还原-氧化降解工艺,分别对4-氯酚进行降解.采用离子色谱、高效液相色谱、TOC仪对4-氯酚降解过程中中间产物及其浓度进行测定.根据公式计算降解过程中理论计算毒性值,应用发光细菌法测定降解过程中的实际毒性值,对理论计算毒性值与实际毒性值进行比较,分析不同体系下降解过程中毒性的变化规律.结果表明,两种工艺体系在最佳降解条件下,阴极室毒性均呈下降的趋势,由于降解过程中在阳极室生成高毒性的苯醌,阳极室毒性均先升高后降低.通过相关性分析得到,两种体系理论计算毒性与实际毒性在P=0.01水平下,相关性系数均为1,显著相关,表明降解过程中实际毒性的测定结果真实可靠.降解至120 min时,三电极体系毒性小于两电极体系,表明三电极体系优于两电极体系.据此提出实际毒性测定方法在电化学还原-氧化工艺降解氯酚类有机废水毒性测试的工业应用中有着广泛的前景.     

Kinetics of photoelectrocatalytic degradation of humic acid using B2O3·TiO2/Ti photoelectrode

An innovative photoelectrode, B₂O₃·TiO₂/Ti electrode, was prepared by galvanostaticanodisation. The morphology and crystalline texture of the B₂O₃·TiO₂ film on electrode were examined by acomic force microscopy (AFM) and X-ray diffraction respectively. The examination results indicated that the anatase was the dominant component. The kinetics of photoelectrocatalytic(PEC) degradation of humic acid(HA) was investigated; the results demonstrated that effects from strongness to weakness on the photoelectrocatalytic degraded rate of humic acid: power of UV-lamp, area of TiO₂ film, bias, original concentration of humic acid solution. The optimum conditions were power of UV-lamp 125 W, area of TiO2 film 42.0 cm² , bias 1.4 V, original concentration of humic acid solution 5 mg/L in this PEC reaction system.     

Structural and photocatalytic properties of TiO2 films fabricated on silicon substrates by MOCVD method

Silicon(111) and Silicon(100) were employed for fabrication of TiO2 films by metal organic chemical vapor deposition( MOCVD).Titanium(Ⅳ) isopropoxide(Ti[O(C3H7)4]) was used as a precursor. The as-deposited TiO2 films were characterized with FE-SEM, XRD and AFM. The photocatalytic properties were investigated by decomposition of aqueous Orange Ⅱ. And UV-VlS photospectrometer was used for checking the absorption characteristics and photocatalytic degradation activity. The crystalline and structural properties of TiO2 film had crucial influences on the photodegradation efficiency. For MOCVD in-situ deposited films on Si substrates, the photoactivities varied following a shape of “M”: at Iower(350℃ ), middle(500℃ ) and higher(800℃ ) temperature of deposition, relative lower photodegradation activities were observed. At 400% and 700% of deposition, relative higher efficiencies of degradation were obtained, because one predominant crystallite orientation could be obtained as deposition at the temperature of two levels, especially a single anatase crystalline TiO2 film could be obtained at 700℃.     

碳黑改性TiO2薄膜光催化剂的结构性质

通过碳黑掺杂制备了改性的TiO₂薄膜光催化剂(CB-TiO₂),并采用液氮吸附、X射线衍射(XRD)和紫外-可见光漫反射光谱(DRS)对催化剂的比表面积、物相、晶粒度和最大激发波长等结构性质进行了表征.结果表明,CB-TiO₂的吸附性能大大改善,不同热处理温度下,BET比表面积增加50%～80%;同时碳黑掺杂能够减小催化剂的晶粒尺度,使相变温度降低.相应的光催化降解试验也表明,碳黑改性TiO₂的活性大大提高,其一级反应速率常数为普通TiO₂的1.5倍.     

Effect of Sb dopant amount on the structure and electrocatalytic capability of Ti/Sb-SnO2 electrodes in the oxidation of 4-chlorophenol

Ti/Sb-SnO_2 anodes were prepared by thermal decomposition to examine the influence',of the amount of Sb dopant on the structure and electrocatalytic capability of the electrodes in the oxidation of 4-chlorophenol.The physicochemical properties of the Sb-SnO_2 coating were markedly influenced by different amounts of Sb dopant.The electrodes,which contained 5% Sb dopant in the coating, presented a much more homogenous surface and much smaller mud-cracks,compared with Ti/Sb-SnO_2 electrodes containing 10% or 15% Sb dopant,which exibited larger mud cracks and pores on the surface.However,the main microstructure remained unchanged with the addition of the Sb dopant.No new crystal phase was observed by X-ray diffraction(XRD).The electrochemical oxidation of 4-chlorophenol on the Ti/SnO_2 electrode with 5% Sb dopant was inclined to electrochemical combustion;while for those containing more Sb dopant,intermediate species were accumulated.The electrodes with 5% Sb dopant showed the highest efficiency in the bulk electrolysis of 4-chlorophenol at a current density of 20 mA/cm~2 for 180 min;and the removal rates of 4-chlorophenol and COD were 51.0% and 48.9%,respectively.     

Preparation of TiO2/Ti mesh photoelectrode and properties

An innovative photoelectrode,TiO2/Ti mesh electrode,was prepared by anodisation.In anodisation,0.5 mol/L H2SO4 was used as electrolytic solution,the current had been constantly 1A from the beginning of the oxidation until reaching a designed voltage.Results showed that the photocatalytic activity of electrode was better when the designed voltage was 160 V.The morphology and the crystalline texture of the TiO2 film on mesh electrode were examined by scanning electronic microseopy and Raman spectruscopy respectively.The examination results indicated that the structure and properties of the film depended on anodisation rate,and the anatase was the dominant component under the eontrolled experimental conditions.Degradation of Rhodamine B in photocatalytic (PC)and photoelectrocatalytic(PEC) reaction was investigated.     

TiO2/PS/Fe3O4 光催化剂的低温制备及其光催化和磁回收性能

以聚苯乙烯(PS)包覆油酸修饰过的纳米Fe3O4为磁核,在低温(90℃)、中性(pH=7左右)条件下,制备了以PS为惰性隔离层的磁载TiO2光催化剂.用X射线衍射仪(XRD)、透射电子显微镜(TEM)、傅里叶红外分光光度计(FT-IR)、振动样品磁强计(VSM)对催化剂的物相组成、形貌、表面性质、磁学性质进行了表征.以苯酚为模拟污染物,考察了其光催化活性,以自制的磁回收装置,考察其回收特性.结果表明,低温制备的TiO2为锐钛矿结构,平均粒径为2～5 nm,催化剂TiO2/PS/Fe3O4[其中物质的量比为n(TiO2)∶n(St)∶n(Fe3O4)=60∶2.5∶1]具有结构完整的壳/壳/核结构,TiO2在PS/Fe3O4表面负载牢固;光催化降解苯酚遵循一级反应动力学方程,TiO2/PS/Fe3O4[n(TiO2)∶n(St)∶n(Fe3O4)=60∶2.5∶1]的反应速率常数K=0.025 8,与纯TiO2的活性接近(K=0.026 2);循环使用5次后,反应速率常数仅降低0.003 4.所制催化剂具有较强的磁感应强度,平均回收率可达到92%以上.该低温水解法制备的磁载TiO2光催化剂具有良好的应用前景.     

Pd-Fe/石墨烯多功能催化阴极降解4-氯酚机制研究

制备出Pd-Fe/石墨烯多功能催化阴极,与Ti/Ir O2/Ru O2阳极、有机涤纶滤布构成隔膜电解体系,将阴极催化加氢脱氯作用和阴阳极氧化作用耦合起来对含4-氯酚的有机废水进行降解,采用TOC仪、紫外扫描、高效液相色谱、离子色谱分析方法研究其降解效果及反应历程.结果表明,在最佳反应条件下,Pd-Fe/石墨烯催化体系阴阳极室中4-氯酚转化率分别为98.1%和95.1%,优于Pd/石墨烯催化体系阴阳极室的93.3%和91.4%.Pd-Fe/石墨烯催化体系脱氯效果高于95%,表明双金属催化剂具有更强的析氢能力.在阴阳极的协同作用下,反应120 min时4-氯酚被完全转化.通过阴极加氢脱氯作用,4-氯酚被还原成苯酚.随后苯酚在阴阳极的共同氧化作用下,被氧化生成对二苯酚、苯醌等中间产物,继而被氧化为小分子有机酸,最后被矿化为CO2和H2O,据此提出了4-氯酚降解的可能历程.     

纳米TiO2催化燃烧固硫的实验研究

通过纳米TiO₂催化CaO燃烧后粉煤灰的成分分析和燃烧烟气中SO₂含量的测定确定固硫效果,探讨了纳米TiO₂添加量、Ca/S摩尔比、不同条件制备的纳米TiO₂及燃烧温度对分析纯CaO固硫的影响,比较了纳米TiO₂对不同煤种以及不同钙基固硫剂的固硫效果,并对反应产物进行了X射线衍射和扫描电镜分析.结果表明,纳米TiO₂与CaO共同作用时,纳米TiO₂最佳的添加量为8%;在Ca/S摩尔比为2、燃烧温度为850℃时纳米TiO₂催化分析纯和工业纯CaO固硫效率达87.8%和60.3%,比不添加纳米TiO₂时增加13.4%和29.6%.纳米TiO₂对不同煤种燃烧时CaO固硫有较好地催化作用,能够促进SO₂转化成SO₃的本征反应,同时增加煤灰的孔尺寸,促进二氧化硫的扩散从而提高CaO的固硫效果.     

掺氮Ta2O5诱发可见光-类Fenton体系降解阿特拉津研究

通过制备具有强可见光吸收和活性的半导体掺氮Ta2O5,利用其可见光Fe3+还原活性,实现了可见光-类Fenton体系有效地降解阿特拉津.结果表明,氨气流量0.3 L.min-1、700℃氮化时间6 h制备出的掺氮Ta2O5在可见光下还原Fe3+的能力最佳;阿特拉津降解效果与各种操作条件———光强、催化剂投加量、Fe3+、H2O2、阿特拉津初始浓度及pH值有关,并通过H2O2的分解揭示影响的原因.在pH为2.6、[atrazine]0=18 mg.L-1、[H2O2]0=2.5 mmol.L-1、[Fe3+]0=0.5 mmol.L-1、掺氮Ta2O5投加量为0.6 g.L-1、500 W氙灯照射下,反应60 min时,阿特拉津的降解率为97%.该研究为可见光-类Fenton体系降解有机污染物的实际应用提供了基础数据和理论指导.     

Ti/Ti4O7阳极电化学氧化降解水中的美托洛尔

等离子喷涂法制备了钛基亚氧化钛电极(Ti/Ti_4O_7),以该电极为阳极,研究了电化学氧化法对水中美托洛尔的去除效果.考察了电流密度(5~25 mA·cm~(-2))、极板间距(5~25 mm)和初始浓度(3~50 mg·L~(-1))对美托洛尔电化学降解效率的影响;分析美托洛尔电化学降解过程中溶液总有机碳(TOC)和毒性的变化,鉴别反应中间产物并计算其毒性.研究表明:Ti/Ti_4O_7阳极电化学降解美托洛尔反应符合一级反应动力学规律(R20.95),降解效率随电流密度的增大而增大,随极板间距和初始浓度的增大而减小;TOC去除率在反应40 min后可达56.5%;反应过程中产生了质合比为266、250、223和207的中间产物,造成美托洛尔溶液的生物毒性在电化学反应过程中先升高后下降.     

TiO2/PPY/Fe3O4的水热法制备及其光催化与磁回收性能

以化学氧化法制备的聚吡咯(PPY)包覆Fe3O4复合材料为磁核,用水热反应法(170℃, pH=7±0.2)在其表面负载了纳米Ti02,制成壳/壳/核结构的磁载二氧化钛光催化剂.并用X射线衍射仪(XRD)、透射电子显微镜(TEM)、傅里叶红外分光光度计(FT-IR)、振动样品磁强计(VSM)、Zeta电位仪对催化剂的物相组成、形貌、表面性质、磁学性质以及磁核的表面电位进行了表征分析.以初始浓度为25mg/L的苯酚溶液为模拟污染物, 对其进行光催化降解以考察其催化活性;并以自制的磁回收装置考察其磁回收率.结果表明,所制备的Ti02粒径在4~7nm,具有混晶结构,其中锐钛矿占95.2%,金红石占4.8%;PPY对Ti02在磁核表面的负载具有促进作用,TiO2在PPY/Fe3O4表面负载牢固;催化剂TPF(nTiO2:n PPY:nFe3O4 =30:2.1:1)具有良好的壳/壳/核结构,其磁感应强度为40emu/g,具有超顺磁性;所制备的催化剂光催化降解苯酚符合假一级反应动力学方程,其中纯TiO2、P25、TPF反应速率常数K值分别为0.0279、0.0264、0.0252,TPF循环使用5次后K值为0.020,催化活性略有降低,循环使用平均回收率可达到90.35%. 该法制备的磁载Ti02光催化剂具有优良的催化活性和磁回收性能,具有良好的应用前景.     

Visible light responsive N-F-codoped TiO2 photocatalysts for the degradation of 4-chlorophenol

Visible light responsive N-F-codoped TiO₂ photocatalysts exhibit a higher catalytic activity than N-doped TiO₂ for the degradation of 4-chlorophenol due to the synergistic effect of nonmetal elements.     

温和条件下磁性Pd-MgFe2O4/MgAl(O)催化4-氯苯酚高效加氢脱氯

以镁铁尖晶石MgFe₂O₄为磁核,在磁核表层包覆MgAl水滑石后经高温焙烧形成MgAl （O）复合氧化物包覆的磁性载体MgFe₂O₄/MgAl （O）,进而负载纳米金属Pd制成磁性催化剂Pd-MgFe₂O₄/MgAl （O）.通过X射线衍射（XRD）、X射线光电子能谱分析（XPS）、傅里叶红外光谱（FT-IR）、透射电镜（TEM）、扫描电子显微镜（SEM）、选区电子衍射（SAED）、比表面积（S_BET）和振动样品磁强计（VSM）等手段对催化材料进行表征.结果表明,MgFe₂O₄-LDH转化为磁性MgFe₂O₄/MgAl （O）载体有利于催化材料比表面积的增加、结构稳定性的提升及相应催化活性位点的增加,进而有利于提升4-氯苯酚高效加氢脱氯效率.研究进一步考察了催化剂负载量、催化剂用量、底物浓度、反应温度、反应溶剂等条件对4-氯苯酚降解效率的影响.结果发现,在优化反应条件下催化反应的转换频率TOF （0.04 s^-1）可媲美常温、常压、无碱性添加剂等温和条件下4-氯苯酚高效加氢脱氯反应的最佳文献报道水平.磁性催化剂Pd-MgFe₂O₄/MgAl （O）循环使用4次后仍保持很好的催化活性.     

Ti/RuO2-IrO2电极电化学方法降解溶液中TBBPA及其降解机理探究

四溴双酚A(TBBPA)是世界上产量和用量最大的溴代阻燃剂之一,在河流、底泥及污水中持久存在,严重威胁环境和人体健康.探讨了阳极为Ti/RuO_2-IrO_2电极的电化学法对溶液中TBBPA的降解效率,并考察了电流密度(5~20 m A·cm~(-2))、初始pH值(3~11)、极板间距(1~3 cm)及电解质浓度(1~40 mmol·L~(-1))对降解速率的影响.研究结果表明,TBBPA的降解遵循一级动力学方程,在溶液初始浓度为5 mg·L~(-1)、电流密度为10 mA·cm~(-2)、电解质浓度为5 mmol·L~(-1)及极板间距为1 cm的条件下,60 min后TBBPA的降解率可达97.2%,且降解速率常数和半衰期分别为0.060 min~(-1)和11.6 min,能量消耗为105.3 k Wh·m~(-3).同时运用HPLC-MS/MS检测出中间产物双酚A(BPA)和2-溴苯酚,并推断其降解途径主要为在羟基自由基(·OH)作用下连续的脱溴过程中,苯环与异丙基之间的C—C键断裂生成BPA和2-溴苯酚.电化学法是一种高效的、有潜力的降解难降解有机污染物的方法,本文将为今后实际废污水中TBBPA的去除提供基础数据和技术参数.     

二氧化钛的制备及光催化降解阳离子艳红染料

以Ti(OC4H9) 4为原料 ,采用沉淀法制备出光催化剂TiO2 微粒 ,并用所制得的样品对阳离子艳红染料进行了光催化降解实验。讨论了催化剂的制备条件对催化剂TiO2 降解性能的影响。结果表明 :沉淀pH为 8 0、粒径 <2 0 0目、经蒸馏水和无水乙醇洗涤、焙烧温度为 5 0 0℃所得的微粒催化降解效果最好。在此催化剂的作用下 ,经 3 0min的照射 ,阳离子艳红染料的降解率大于 87%