Numerical study of medium to large scale BLEVE for blast wave prediction

So far, the prediction of blast wave generated from the Boiling Liquid Expanding Vapour Explosion (BLEVE) has been already broadly investigated. However, only a few validations of these blast wave prediction models have been made, and some well-established methods are available to predict BLEVE overpressure in the open space only. This paper presents numerical study on the estimation of the near-field and far-field blast waves from BLEVEs. The scale effect is taken into account by conducting two different scale BLEVE simulations. The expansion of pressurized vapour and evaporation of liquid in BLEVE are both modelled by using CFD method. Two approaches are proposed to determine the initial pressure of BLEVE source. The vapour evaporation and liquid flashing are simulated separately in these two approaches. Satisfactory agreement between the CFD simulation results and experimental data is achieved. With the validated CFD model, the results predicted by the proposed approaches can be used to predict explosion loads for better assessment of explosion effects on structures.     

An experimental study on the temperature dependence of CO2 explosive evaporation

The need for transportation and storage of CO₂ in bulk quantities is likely to increase in the near future. The handling of CO₂ on such scale gives rise to a number of technological challenges and safety aspects. The accidental rupture of a vessel containing liquefied CO₂ may lead to a Boiling Liquid Expanding Vapour Explosion (BLEVE). Whether explosive evaporation of liquefied CO₂ is also possible at storage temperatures below the homogeneous nucleation temperature 271 K (?2 °C) is unclear.This article describes the results of 12 experiments with 40 L CO₂ cylinders at various temperatures to investigate the temperature dependence of explosive evaporation. The cylinders were opened with linear shaped charges to simulate a near instantaneous rupture, and blast was measured at various locations. The observed blast could be clearly attributed to explosive evaporation. The results show that below the homogeneous nucleation temperature, BLEVE blast does not disappear abruptly, but instead follows a gradual decay. Predictions with a numerical BLEVE blast model overestimate the observed blast peak overpressure and impulse, but qualitatively show a similar behaviour. The energy lost by the acceleration of the cylinder parts is a possible reason for overestimations of the model.The consequence of the test results is that for accident scenarios with CO₂ at low temperatures a BLEVE should not be neglected in hazard assessments. Future large scale bulk storage will take place at a 10⁵ times larger volume than the cylinders applied in the current small scale experiments. We expect that the blast-reducing effects of a tank shell will disappear at such scale.The research leading to these results has received funding from the European Community's Seventh Framework Programme (FP7/2007–2013) under grant agreement n° 241381.     

Blast overpressures from medium scale BLEVE tests

The measured blast overpressures from recent tests involving boiling liquid expanding vapour explosions (BLEVE) has been studied. The blast data came from tests where 0.4 and 2 m³ ASME code propane tanks were exposed to torch and pool fires. In total almost 60 tanks were tested, and of these nearly 20 resulted in catastrophic failures and BLEVEs. Both single and two-step BLEVEs were observed in these tests. This paper presents an analysis of the blast overpressures created by these BLEVEs. In addition, the blast overpressures from a recent full scale fire test of a rail tank car is included in the analysis.The results suggest that the liquid energy content did not contribute to the shock overpressures in the near or far field. The liquid flashing and expansion does produce a local overpressure by dynamic pressure effects but it does not appear to produce a shock wave. The shock overpressures could be estimated from the vapour energy alone for all the tests considered. This was true for liquid temperatures at failure that were below, at and above the atmospheric superheat limit for propane. Data suggests that the two step type BLEVE produces the strongest overpressure. The authors give their ideas for this observation.The results shown here add some limited evidence to support previous researchers claims that the liquid flashing process is too slow to generate a shock. It suggests that liquid temperatures at or above the Tsl do not change this. The expansion of the flashing liquid contributes to other hazards such as projectiles, and close in dynamic pressure effects. Of course BLEVE releases in enclosed spaces such as tunnels or buildings have different hazards.     

On the mechanism of a BLEVE occurrence due to fire engulfment of tanks with overheated liquids

The BLEVE (boiling liquid expanding vapor explosion) effect that involves the formation of a fireball occurs at the engulfment by fire of a tank with a highly flammable liquid or a liquid gas. Heating of the tank causes elevation of the liquid phase temperature and pressure inside the tank. A partial rupture of the dry tank walls is possible, with the formation of a rarefaction wave propagating into the liquid phase. An evaporation wave moves after the rarefaction wave and cause a rapid increase of pressure, exceeding the initial pressure before depressurization. Rapid violent destruction of the tank occurs. The mechanism of a BLEVE initiation is considered using Van der Waals isotherms. The following criterion for the possibility of a BLEVE was formulated. If the final state is located on an unstable part of the Van der Waals isotherm, a BLEVE takes place. Limiting values of the temperatures for overheating of certain highly flammable liquids and liquid gases (propane, n-butane, n-pentane, isopentane) were calculated using the proposed method, and were found to be in good agreement with experimental data available in the literature.     

Case study: Assessment on large scale LPG BLEVEs in the 2011 Tohoku earthquakes

After the 2011 Tohoku earthquakes, several chemical and oil complexes on the Pacific Ocean shoreline of northeast Japan experienced massive losses. In Chiba, a refinery operated by Cosmo Oil lost 17 LPG storage vessels which were either heavily damaged or totally destroyed by fires and explosions in the refinery. These large vessels ranged in size from 1000 to 5000 m³. The estimated volume of LPG at the time of the incident was between 400 and 5000 m³ for each vessel. Five boiling liquid expanding vapor explosions (BLEVEs) of LPG occurred, resulting in huge fire balls measuring about 500 m in diameter.A BLEVE is defined as the explosive release of expanding vapor and boiling liquid when a container holding a pressure-liquefied gas fails catastrophically. It is thus important to estimate the physical properties of superheated liquids: the thermodynamic and transport properties, the intrinsic limits to superheating and depressurization, and the nature of thermodynamic paths. Also it is hoped to provide better understanding of the vessels designed, manufactured, installed, and operated to reduce or eliminate the probability that a sequence of events will result in BLEVE or loss of primary containment. Knowledge of these matters is still incomplete. The objective of this research is to estimate the significant BLEVE phenomenon in very large scale spherical vessels based on published information in Japan. There are some models predicting BLEVEs. However, it is essential to know if this is true for very large scales such as spheres since validation is usually rare to provide confidence in estimating the superheated liquids behaviors. To this end, comparing with the information on this event, the conditions in the five LPG vessels at the time of the BLEVE were determined in terms of: duration of vessel failure (time to BLEVE); mass fraction in the vessel with time; temperature distribution in the liquid and vapor region and pressure within the vessel (e.g. initial pressure and internal high-speed transient pressure during failure), by means of a computer program AFFTAC Analysis of Fire Effects on Tank Cars, which solves heat conduction, stress and a failure model of the tank, a thermodynamic model of its fluid contents, and a flow model for the lading flowing through the safety relief device. Subsequently, the consequences from the sphere BLEVE, such as the expected fireball diameter and duration and the expected blast overpressure produced by the BLEVE failures, are also subjects of active research. Here the blast using the methods of PHAST and SFPE Handbook of Fire Protection Engineering was calculated.Results suggest that methodologies here used gave reasonable estimations for such real and huge BLEVEs in a validated way, which may provide valuable guidance for risk mitigation strategy with regard to LPG facility in design, emergency planning, resiliency, operations, and risk management.     

Analysis of the boiling liquid expanding vapor explosion (BLEVE) of a liquefied natural gas road tanker: The Zarzalico accident

The road accident of a tanker transporting liquefied natural gas (LNG) originated a fire and, finally, the BLEVE of the tank. This accident has been analyzed, both from the point of view of the emergency management and the explosion and fireball effects. The accidental sequence is described: fire, LNG release, further safety valves release, flames impingement on vessel unprotected wall, vessel failure mode, explosion and fireball. According to the effects and consequences observed, the thermal radiation and overpressure are estimated; a mathematical model is applied to calculate the probable mass contained in the vessel at the moment of the explosion. The peak overpressure predicted from two models is compared with the values inferred from the accident observed data. The emergency management is commented.     

A closer look at BLEVE overpressure

The overpressure produced by the boiling liquid expanding vapor explosion (BLEVE) is still not well understood. Various methods have been published on the overpressure modeling in the far field. They mostly differ by the modeling of the expansion energy, used to scale the distance to the source where the overpressure needs to be calculated. But these methods usually include a experimentally fitted reduction factor, and are mostly overestimating the overpressures. Today there is a growing interest in modeling the BLEVE overpressure in the near field, for studying the blast effect on critical infrastructure such as bridges and buildings. This requires a much better understanding of the BLEVE blast. This paper goes deeper in the understanding of the physical phenomenon leading to the BLEVE blast wave generation and propagation. First, mid-scale BLEVE experiments in addition to new experimental data for near field blast from a small scale supercritical BLEVE are analyzed. And second, an analysis method of the shocks observed in the experiments is presented based on fundamental gas dynamics, and allows the elaboration of a new modeling approach for BLEVE overpressure, based on the calculation of the initial overpressure and radius of the blast.     

An innovative and comprehensive approach for the consequence analysis of liquid hydrogen vessel explosions

Hydrogen is one of the most suitable solutions to replace hydrocarbons in the future. Hydrogen consumption is expected to grow in the next years. Hydrogen liquefaction is one of the processes that allows for increase of hydrogen density and it is suggested when a large amount of substance must be stored or transported. Despite being a clean fuel, its chemical and physical properties often arise concerns about the safety of the hydrogen technologies. A potentially critical scenario for the liquid hydrogen (LH₂) tanks is the catastrophic rupture causing a consequent boiling liquid expanding vapour explosion (BLEVE), with consequent overpressure, fragments projection and eventually a fireball. In this work, all the BLEVE consequence typologies are evaluated through theoretical and analytical models. These models are validated with the experimental results provided by the BMW care manufacturer safety tests conducted during the 1990's. After the validation, the most suitable methods are selected to perform a blind prediction study of the forthcoming LH₂ BLEVE experiments of the Safe Hydrogen fuel handling and Use for Efficient Implementation (SH₂IFT) project. The models drawbacks together with the uncertainties and the knowledge gap in LH₂ physical explosions are highlighted. Finally, future works on the modelling activity of the LH₂ BLEVE are suggested.     

Morphological characteristics of flashing jet throughout superheated liquid release

Many release problems involve two-phase releases of hazardous materials of superheated liquids with high energy into the atmosphere. Such accidents are accompanied by violent phase transition and form catastrophic flashing jets. In this work, experimental and theoretical analyses were conducted to investigate dynamic characteristics of flashing jet morphology and their dependence on pressure-decay dynamics under different storage pressures, superheats, and nozzle diameters. Flashing jet morphology and angle throughout two-phase releases were captured by a high-speed camera, and the corresponding source pressure in the superheated liquid tank was measured simultaneously. Results show that three typical phases, expansion, stabilization, and decay, are characterized throughout two-phase release based on the evolution of flashing jet morphology. The jet initially expands gradually due to the enhancement of phase transition intensity, and then keeps stable when the intensity reaches its maximum, and terminally decays rapidly due to the depletion of superheated liquid. Phase transition intensity at the nozzle exit is mainly controlled by the pressure-decay dynamics. Bubbles nucleation inception sites gradually move upstream of the nozzle during the pressure decay process increasing the phase transition intensity. The increase of storage pressure, superheat and nozzle diameter promotes the mechanical and thermodynamic effects on the jet breakup. The significant increase of mechanical and thermodynamic effects effectively accelerates droplets evaporation and further affects flashing jet morphology.     

The velocity of end-cap and rocket missiles generated by failure of a gas pressurised vessel containing particulate material

Many industrial installations include pressure vessels which contain high pressure gas and particulate material. Given the rupture of such a vessel, it is established that provided the particulate acceleration is not greater than the acceleration of a detached end-cap, the end-cap velocity will be similar to that generated by rupture of a gas filled vessel with the same available gas expansion energy. In contrast, if the particulates accelerate to overtake the end-cap, the momentum transfer resulting from the bombardment of the end-cap by the particulates generates a higher end-cap velocity. The latter can be similar to that generated when the rupturing vessel contains only high pressure gas and a consequent greater gas expansion energy than available when the vessel contains both high pressure gas and particulates.The velocity of a `rocket' missile resulting from failure of a gas-pressurised vessel containing particulate material is greater than that generated by failure of a similar vessel containing only high pressure gas.     

液化石油气BLEVE事故研究

为了减小液化石油气沸腾液体扩展蒸汽云爆炸事故后果,采用ALOHA软件对液化石油气储罐泄漏事故进行研究,基于液化石油气泄漏量、空气湿度、风速、储存温度等爆炸事故后果影响因素进行数值模拟。研究结果表明:液化石油气泄漏量越大,沸腾液体扩展蒸汽云爆炸事故产生的火球直径越大,燃烧时间或热辐射时间越长,且造成的危害范围越大,事故后果越严重;随着空气湿度增加,事故影响的范围逐渐减小,事故后果相对减小;随着液化石油气储存温度增加,事故影响范围逐渐减小;风速对于事故影响范围无影响;空气湿度、储存温度及风速对火球直径及火球燃烧时间无影响。     

Small scale experiments on boiling liquid expanding vapor explosions: Vessel over-pressure

The boiling liquid expanding vapor explosion (BLEVE) is a type of physical explosion that has caused massive damage in the petrochemical industry. In this paper, a study has been made of the conditions that could lead to a BLEVE. A device was built to simulate the occurrence of suddenly initiated release through a top orifice. As there is some danger in using liquefied petroleum gas (LPG) in the experiments, water was used as the test fluid. The change of pressure and temperature was measured during the experiment. It was determined that two pressure peaks result after the pressure is released: the first pressure peak seems to occur because of the vapor pressure caused by the swelled two-phase layer after the initial venting, the second pressure peak is possibly due to a dynamic impact or ‘liquid hammer’ and is maintained by bubbles collapse or something like cavitation at the surface of the inner wall of the head space that occurs with the ejection of two-phase flow.Liquid heights, orifice size, and the degree of liquid superheating all have differing influence on the magnitude of the measured over-pressure; the greater the degree of liquid superheat, the stronger the over-pressure; smaller opening areas delay and reduce the magnitude of the first over-pressure; at fill levels between 60% and 80%, the impact pressure appears more violent than with other fills.     

氯气和光气爆燃事故源强估算

在建立化学品泄漏的气体排放、液体排放、两相排放模式和爆炸燃烧的火球和气爆，蒸气云爆炸及绝热扩散和池蒸发扩展等模式的基础上，估计分析了氯气和光气爆燃事故源强，即爆炸能量及碎片抛射、冲击波、热辐射和毒云等后果影响     

BLEVE火球热辐射及其影响评价模型介绍

高压液化易燃、易爆化学品储罐易发生BLEVE,引起热辐射,会造成周围人员伤亡和设备损坏.介绍了BLEVE火球热辐射及其影响模型,通过该模型可以计算BLEVE火球的尺寸、持续时间、升空高度、热辐射通量及预测暴露在BLEVE火球热辐射通量下人的致死概率.     

Prediction of BLEVE mechanical energy by implementation of artificial neural network

In the event of a BLEVE, the overpressure wave can cause important effects over a certain area. Several thermodynamic assumptions have been proposed as the basis for developing methodologies to predict both the mechanical energy associated to such a wave and the peak overpressure. According to a recent comparative analysis, methods based on real gas behavior and adiabatic irreversible expansion assumptions can give a good estimation of this energy. In this communication, the Artificial Neural Network (ANN) approach has been implemented to predict the BLEVE mechanical energy for the case of propane and butane. Temperature and vessel filling degree at failure have been considered as input parameters (plus vessel volume), and the BLEVE blast energy has been estimated as output data by the ANN model. A Bayesian Regularization algorithm was chosen as the three-layer backpropagation training algorithm. Based on the neurons optimization process, the number of neurons at the hidden layer was five in the case of propane and four in the case of butane. The transfer function applied in this layer was a sigmoid, because it had an easy and straightforward differentiation for using in the backpropagation algorithm. For the output layer, the number of neurons had to be one in both cases, and the transfer function was purelin (linear). The model performance has been compared with experimental values, proving that the mechanical energy of a BLEVE explosion can be adequately predicted with the Artificial Neural Network approach.     

Pool evaporation: Experimental tests at medium-scale with gasoline

Pool evaporation is a major source of flammable vapour clouds. Predicting the evaporation rate of a liquid hydrocarbon pool is therefore a key issue of dispersion modelling for safety concerns. This paper presents small- and medium-scale experiments of pool evaporation carried out with liquid hydrocarbons (pentane, heptane), hydrocarbon “gasoline-like” mixtures and gasoline. Liquid mass loss was measured and the evaporation rate deduced with its evolution in time. Other observations are highlighted, regarding the evolution of liquid temperatures, mixture compositions, and scale effects like the influence of pool length on surface evaporation rate. Comparisons with well-known correlations are then shown. The authors finally suggest a new semi-empirical correlation with a set of parameters fitted on the performed experiments.     

Acoustic analysis of blast waves produced by rapid phase transition of LNG released on water

Massive offshore and onshore storage of fuel have led the international community to raise questions about the hazards on the surrounding installations and people. Among the possible accidental scenarios when cryogenic gas as liquefied natural gas (LNG) is spilled on water at a very fast rate, the phenomenon of rapid phase transition (RPT) may occur: large amounts of energy are released during phase transition which can generate explosions. The related consequences should be added to the possible consequences of fire in terms of flash fire, fireball, pool fire, and vapour cloud explosion for confined and congested geometry surrounding the release point.In this paper, the analysis of RPT of LNG has been studied from the point of view of blast wave production, through ab initio acoustic analysis for monopole source. Maximum overpressures, as calculated at the source point and along the blast pathway are compared with results of large scale experiments. Safety distances are given for the sake of comparison with threshold distances reported in the open literature.     

Propagation and intensity of blast wave from hydrogen pipe rupture due to internal detonation

The coupled fluid-structure-rupture model was developed to study the propagation and intensity of blast wave from hydrogen pipe rupture due to internal detonation. The dynamic rupture of pipe and propagation of blast wave were well coupled together in every timestep during the simulation. The numerical model was validated with experiments in terms of both typical rupture profiles and blast overpressures. Results reveal that crack branching of pipe can dramatically increase the rupture opening rate which controls the intensity and shape of the resultant blast wave. Due to the process of crack initiation and extension, the blast wave out of the pipe first forms and then is strengthened by the subsequent compression waves. This makes the maximum peak overpressure appears at a certain standoff distance above the rupture. Despite consuming some percentages of energy, the dynamic rupture of pipe generally presents positive effects (up to 2–3 times) on the blast wave intensity along the jetting direction due to the convergence effect of rupture opening on the release of internal high-pressure gas. Finally, through defining normalized overpressure and impulse based on the same hydrogen detonation in open spaces, the quantitative influences of pipe rupture on the blast wave intensity in cases of different detonation pressures and standoff distances are clarified.     

Experimental investigation of gas explosion in single vessel and connected vessels

Gas explosion in connected vessels usually leads to high pressure and high rate of pressure increase which the vessels and pipes can not tolerate. Severe human casualties and property losses may occur due to the variation characteristics of gas explosion pressure in connected vessels. To determine gas explosion strength, an experimental testing system for methane and air mixture explosion in a single vessel, in a single vessel connected a pipe and in connected vessels has been set up. The experiment apparatus consisted of two spherical vessels of 350 mm and 600 mm in diameter, three connecting pipes of 89 mm in diameter and 6 m in length. First, the results of gas explosion pressure in a single vessel and connected vessels were compared and analyzed. And then the development of gas explosion, its changing characteristics and relevant influencing factors were analyzed. When gas explosion occurs in a single vessel, the maximum explosion pressure and pressure growth rate with ignition at the center of a spherical vessel are higher than those with ignition on the inner-wall of the vessel. In conclusion, besides ignition source on the inner wall, the ignition source at the center of the vessels must be avoided to reduce the damage level. When the gas mixture is ignited in the large vessel, the maximum explosion pressure and explosion pressure rising rate in the small vessel raise. And the maximum explosion pressure and pressure rising rate in connected vessels are higher than those in the single containment vessel. So whenever possible, some isolation techniques, such as fast-acting valves, rotary valves, etc., might be applied to reduce explosion strength in the integrated system. However, when the gas mixture is ignited in the small vessel, the maximum explosion pressures in the large vessel and in the small vessel both decrease. Moreover, the explosion pressure is lower than that in the single vessel. When gas explosion happens in a single vessel connected to a pipe, the maximum explosion pressure occurs at the end of the pipe if the gas mixture is ignited in the spherical vessel. Therefore, installing a pipe into the system can reduce the maximum explosion pressure, but it also causes the explosion pressure growth rate to increase.