微波法污水厂污泥制备活性炭的研究

研究了以污水厂污泥为原料、微波辐照下磷酸活化法制备污泥活性炭的工艺条件,探讨了微波功率、辐照时间以及磷酸浓度对活性炭碘值的影响.结果表明,微波功率480 W、辐照时间315 s、磷酸浓度40%～45%的条件下,制备的污泥活性炭碘值为301 mg/g,总孔孔容是0.37 mL/g,平均孔径8.8 nm,比表面积168 m2/g.将该污泥活性炭用于处理TNT红水,吸附效果良好.     

Utilization of agricultural waste corn cob for the preparation of carbon adsorbent

In the present study, a series of activated carbons were prepared from agricultural waste corn cob by chemical and physical activations with potassium hydroxide (KOH)/potassium carbonate (K2CO3) and carbon dioxide (CO2). The effect of process variables such as impregnation ratio, impregnation time, activation temperature and soaking time of CO2 was studied in order to relate these preparation parameters with the physical properties of final carbon products. The resulting activated carbons were characterized by nitrogen adsorption-desorption isotherms at 77 K. The surface areas and pore volumes of carbons were estimated by the BET equation, the Langmuir equation and the t-plot method. Under the experimental conditions investigated, the main parameters in the activation of corn cob were found to be the impregnation ratio and activation temperature. The soaking time of CO2 is another important variable, which had a strong effect on the pore volume development. The BET surface area and total pore volume were as large as about 2000 m2/g and about 1.0 cm3/g, respectively. This study showed that the activation of agricultural waste corn cob with KOH/K2CO3 and CO2 was suitable for the preparation of large-surface-area activated carbons.     

污泥活性炭的表征及其对Cr（Ⅵ）的吸附特性

以城市污水处理厂污泥为原料，采用磷酸活化一微波热解法制备得到污泥活性炭，并将其用于吸附水溶液中的Cr（Ⅵ）。分别采用元素分析仪（VarioELcube）、比表面积孔径分布测定仪（ASAP2020）、扫描电镜（SEM）和傅里叶红外光谱（FT—IR）等仪器对原污泥及污泥活性炭的表面组成和结构进行表征，探讨污泥活性炭的孔隙结构参数和表面化学性能。通过静态吸附实验，考察了溶液初始pH，接触时间，初始Cr（Ⅵ）浓度对污泥活性炭吸附Cr（Ⅵ）效果的影响，并探讨了污泥活性炭去除Cr（Ⅵ）的机理。实验结果表明，pH越低吸附效果越好，吸附平衡时间为100h。不同温度下吸附过程均符合Langmuir等温吸附模型，30℃时最大吸附容量为27．55mg／g；吸附动力学过程符合准二级速率方程（R2〉0．99）；污泥活性炭对Cr（Ⅵ）的去除是一个吸附-还原耦合的过程。     

Utilization of Arachis hypogaea hull, an agricultural waste for the production of activated carbons to remove phenol from aqueous solutions

Arachis hypogaea hulls, an agricultural waste, were used to prepare activated carbon by chemical activation with zinc chloride under four different activation atmospheres. The most important parameter in chemical activation was found to be the chemical ratio (activating agent/precursor). Carbonization temperature and time are the other two important variables, which had significant effect on the pore structure of carbon. The maximum Brunquer-Emmett-Teller (BET) surface area and micropore volume of the activated carbon was found to be 418 m(2)/g and 0.28 cm(3)/g, respectively. The activated carbon developed shows substantial capability to adsorb phenol from aqueous solutions. The kinetic data were fitted to the models of intraparticle diffusion, pseudo-second-order, and Lagergren, and followed more closely the pseudo-second-order chemisorption model. The isotherm equilibrium data were well fitted by the Langmuir and Freundlich models. Solution pH has significant effect on adsorption and the maximum uptake of phenol was reported at pH 3.5.     

Enhancement of the CO(2) retention capacity of X zeolites by Na- and Cs-treatments

Adsorption of carbon dioxide on alkaline modified X zeolites was investigated by temperature programmed desorption (TPD) analysis of these materials previously saturated with CO(2) at 50, 100 and 200 degrees C. Parent X zeolite (in its sodium form) was treated with different sodium and cesium aqueous solutions, using both carbonates and hydroxides as precursors. The resulting materials were characterised by nitrogen physisorption, XRD, and NH(3)-TPD, in order to determine their morphological, crystallographic and chemical properties. Slight desilication phenomena were observed using hydroxides as precursors, whereas the treatment with Cs salts lead to higher crystallinity losses. Several successive adsorption-desorption cycles were carried out in order to check the regenerability of the adsorbents. Cesium-treated zeolites present higher carbon dioxide retention capacities than the sodium treated and than the parent material. When working with these Cs-modified materials, the desorption takes place mainly at temperatures between 250 and 400 degrees C, results of great practical interest, since it allows the use these kinds of materials for adsorption-desorption cycles. The evolution of the retention capacity with temperature is also markedly more positive for Cs-treated zeolite, especially when carbonate is used as the precursor. These materials maintain high retention capacities at 100 degrees C (10mg g(-1)) and even at 200 degrees C (3mg g(-1)), temperatures at which the most of the adsorbents are inactive.     

稻壳基活性炭制备及其对重金属吸附研究

活性炭吸附法是重金属废水处理的重要方法.利用廉价的稻壳,选择氢氧化钠和磷酸作活化剂制备活性炭,测定了稻壳基活性炭的比表面积、亚甲基蓝吸附值、碘吸附值、苯酚吸附值和等电点.利用制备的稻壳基活性炭吸附溶液中的Cd、Cu、Zn,研究了不同稻壳基活性炭对Cd、Cu,Zn的吸附差异,并利用X射线衍射仪分析了稻壳基活性炭中微晶体结...     

微波法制备污泥活性炭研究

采用微波加热法,以污水厂剩余污泥为原料,磷酸为污泥活化剂制备污泥活性炭.微波功率、辐照时间和磷酸浓度对污泥活性炭吸附性能具有显著影响,在最佳工艺条件微波功率480 W、辐照时间315 s和磷酸浓度40%条件下制得的活性炭碘值301 mg/g,比表面积168 m2/g,污泥中重金属绝大部分被固化.与传统商品炭相比,污泥炭孔隙结构以中孔为主.利用该活性炭处理城市生活污水处理厂出水,COD去除率可达87%以上,污泥炭的吸附等温线用Langmuir等温吸附模型进行描述.     

Production of activated carbons from pyrolysis of waste tires impregnated with potassium hydroxide

Activated carbons were produced from waste tires using a chemical activation method. The carbon production process consisted of potassium hydroxide (KOH) impregnation followed by pyrolysis in N2 at 600-900 degrees C for 0-2 hr. The activation method can produce carbons with a surface area (SA) and total pore volume as high as 470 m2/g and 0.57 cm3/g, respectively. The influence of different parameters during chemical activation, such as pyrolysis temperature, holding time, and KOH/tire ratio, on the carbon yield and the surface characteristics was explored, and the optimum preparation conditions were recommended. The pore volume of the resulting carbons generally increases with the extent of carbon gasified by KOH and its derivatives, whereas the SA increases with degree of gasification to reach a maximum value, and then decreases upon further gasification.     

Pore structure of soot deposits from several combustion sources

Soot was harvested from five combustion sources: a dodecane flame, marine and bus diesel engines, a wood stove, and an oil furnace. The soots ranged from 20% to 90% carbon by weight and molar C/H ratios from 1 to 7, the latter suggesting a highly condensed aromatic structure. Total surface areas (by nitrogen adsorption using the Brunauer Emmett Teller, BET method) ranged from 1 to 85 m2 g(-1). Comparison of the surface area and meso-pore (pores 2-50 nm) surface area predicted by density functional theory (DFT) suggested that the soot was highly porous. Total meso-pore volume and surface area ranged from 0.004-0.08 cm3 g(-1) and from 0.33-6.9 m2 g(-1) respectively, accounting for up 33% of the BET surface area. The micro-pore volume (pores <2 nm) calculated from CO2 adsorption data (by DFT) ranged from 0.0009 to 0.013 cm3 g(-1) and micro-pore surface area was 3.1-41 m2 g(-1), accounting for 10-20% of the total intra-particle (meso-plus micro-pores) pore volume and 70-90% of the total intra-particle surface area. Higher pore volume and surface area values were computed using the Dubinin Radushkevich plot technique; ranging from 0.004-0.04 cm3 g(-1) to 11-102 m2 g(-1) for micro-pore volume and surface area, respectively. Comparison of the C/H ratio and the micro-pore structure showed a strong correlation, suggesting a relationship between the condensation of the skeletal structure and micro-porosity of the soot. These data contradict literature reports that soot particles are non-porous and are consistent with recent literature reports that soil organic matter has large micro-pore surface areas.     

微波法污水厂污泥制备活性炭的研究

研究了以污水厂污泥为原料、微波辐照下磷酸活化法制备污泥活性炭的工艺条件,探讨了微波功率、辐照时间以及磷酸浓度对活性炭碘值的影响.结果表明,微波功率480 W、辐照时间315 s、磷酸浓度40%～45%的条件下,制备的污泥活性炭碘值为301 mg/g,总孔孔容是0.37 mL/g,平均孔径8.8 nm,比表面积168 m2/g.将该污泥活性炭用于处理TNT红水,吸附效果良好.     

UTILIZATION OF AGRICULTURAL WASTE CORN COB FOR THE PREPARATION OF CARBON ADSORBENT

In the present study, a series of activated carbons were prepared from agricultural waste corn cob by chemical and physical activations with potassium hydroxide (KOH)/potassium carbonate (K₂CO₃) and carbon dioxide (CO₂). The effect of process variables such as impregnation ratio, impregnation time, activation temperature and soaking time of CO₂ was studied in order to relate these preparation parameters with the physical properties of final carbon products. The resulting activated carbons were characterized by nitrogen adsorption[ch-[chdesorption isotherms at 77 K. The surface areas and pore volumes of carbons were estimated by the BET equation, the Langmuir equation and the t-plot method. Under the experimental conditions investigated, the main parameters in the activation of corn cob were found to be the impregnation ratio and activation temperature. The soaking time of CO₂ is another important variable, which had a strong effect on the pore volume development. The BET surface area and total pore volume were as large as about 2000 m²/g and about 1.0 cm³/g, respectively. This study showed that the activation of agricultural waste corn cob with KOH/K₂CO₃ and CO₂ was suitable for the preparation of large-surface-area activated carbons.     

Characterization of activated carbons prepared from sugarcane bagasse by ZnCl2 activation.

Activated carbons were prepared from the agricultural waste of sugarcane bagasse by the chemical activation with zinc chloride (ZnCl2) at the activation temperature of 500 degrees C with soaking time of 0.5 hour. The influence of activation parameters on the final carbon products was examined by varying the impregnation ratio (i.e., mass ratio of added ZnCl2 to bagasse) and bagasse size. The physical properties of carbon products were characterized by nitrogen adsorption/desorption isotherms (at 77 K) and helium displacement method. The surface area and pore volume of carbons were thus obtained by the BET equation and t-plot method. Also, the particle density and porosity of carbons were estimated by the total pore volume and true density. The increases of the values of surface area and pore volume are approximately proportional to the impregnation ratio. The microporous carbon product with the BET surface area of 905 m2/g and total pore volume of 0.44 cm3/g was obtained in the present study. Further, the adsorption isotherms of two acid dyes from aqueous solutions onto the carbon products were performed at 30 degrees C. The results show that the adsorption isotherms of acid dyes with high molecular weight or large molecular size on the microporous adsorbents of activated carbons are plateau forms, indicating multilayer adsorptions, which may be attributed to the steric hindrance of the adsorbate molecules.     

The removal of uranium (VI) from aqueous solutions onto activated carbon developed from grinded used tire

In this study, activated carbon was prepared from waste tire by KOH chemical activation. The pore properties including the BET surface area, pore volume, pore size distribution, and average pore diameter were characterized. BET surface area of the activated carbon was determined as 558 m²/g. The adsorption of uranium ions from the aqueous solution using this activated carbon has been investigated. Various physico-chemical parameters such as pH, initial metal ion concentration, and adsorbent dosage level and equilibrium contact time were studied by a batch method. The optimum pH for adsorption was found to be 3. The removal efficiency has also been determined for the adsorption system as a function of initial concentration. The experimental results were fitted to Langmuir, Freundlich, and Dubinin–Radushkevich (D-R) isotherm models. A comparison of best-fitting was performed using the coefficient of correlation and the Langmuir isotherm was found to well represent the measured sorption data. According to the evaluation using the Langmuir equation, the saturated monolayer sorption capacity of uranium ions onto waste tire activated carbon was 158.73 mg/g. The thermodynamic equilibrium constant and the Gibbs free energy were determined and results indicated the spontaneous nature of the adsorption process. Kinetics data were best described by pseudo-second-order model.     

Cellulose supported layered double hydroxides for the adsorption of fluoride from aqueous solution

Cellulose supported layered double hydroxides (CSLDHs) were synthesized and tested for adsorption of fluoride in aqueous medium. Three samples of cellulose supported LDHs were synthesized by varying the LDH loading on cellulose. The raw cellulose, unsupported LDH and cellulose supported LDHs were characterized by XRD, SEM and BET surface area. Batch adsorption as well as fixed-bed column experiments were performed for determining the fluoride adsorption characteristics of CSLDHs. The fluoride adsorption properties of CSLDHs were found to be superior to that of reported adsorbents, including activated alumina and carbon nanotubes. Defluoridation capacity of the CSLDHs was 2-4 times higher than that of unsupported LDH. The cellulose supported LDH, CSLDH-50, having an LDH loading of 27% showed maximum fluoride uptake capacity (5.29 mg g(-1) of CSLDH, 25.18 mg g(-1) of LDH) in fixed-bed column study.     

Utilization of Arachis hypogaea hull,an agricultural waste for the production of activated carbons to remove phenol from aqueous solutions

Arachis hypogaea hulls, an agricultural waste, were used to prepare activated carbon by chemical activation with zinc chloride under four different activation atmospheres. The most important parameter in chemical activation was found to be the chemical ratio (activating agent/precursor). Carbonization temperature and time are the other two important variables, which had significant effect on the pore structure of carbon. The maximum Brunquer-Emmett-Teller (BET) surface area and micropore volume of the activated carbon was found to be 418 m²/g and 0.28 cm³/g, respectively. The activated carbon developed shows substantial capability to adsorb phenol from aqueous solutions. The kinetic data were fitted to the models of intraparticle diffusion, pseudo-second-order, and Lagergren, and followed more closely the pseudo-second-order chemisorption model. The isotherm equilibrium data were well fitted by the Langmuir and Freundlich models. Solution pH has significant effect on adsorption and the maximum uptake of phenol was reported at pH 3.5.     

Preparation of activated carbons from raw and biotreated agricultural residues for removal of volatile organic compounds

Activated carbons with diverse physical and chemical properties were produced from four agriculture residues, including raw barley husk, biotreated barley husk, rice husk, and pistachio shell. Results showed that with adequate steam activation (30-90 min, 50% H2O(g),/50% N2), activated carbons with surface areas between 360 and 950 m2 g(-1) were developed. Further increases in the activation time destroyed the pore structure of activated carbons, which resulted in a decrease in the surface area and pore volume. Biotreated agricultural residues were found to be suitable precursors for producing mesoporous activated carbons. The oxygen content of activated carbons increased with increasing activation time. Results from X-ray photoelectron spectroscopy examination further suggested that H2O molecules react with the carbon surface, enhancing the deconvoluted peak area of carbonyl and carboxyl groups. Equilibrium adsorption of toluene indicated that the adsorption capacities increased with an increase in the inlet toluene concentration and a decrease in temperature. The adsorption isotherms were successfully fitted with Freundlich, Langmuir, and Dubinin-Radushkevich equations. Activated carbons derived from agricultural residues appear to be more applicable to adsorb volatile organic compounds at a low concentration and high-temperature environment.     

Preparation of activated carbon using low temperature carbonisation and physical activation of high ash raw bagasse for acid dye adsorption

Activated carbons were prepared from bagasse through a low temperature (160 degrees C) chemical carbonisation treatment and gasification with carbon dioxide at 900 degrees C. The merit of low temperature chemical carbonisation in preparing chars for activation was assessed by comparing the physical and chemical properties of activated carbons developed by this technique to conventional methods involving the use of thermal and vacuum pyrolysis of bagasse. In addition, the adsorption properties (acid blue dye) of these bagasse activated carbons were also compared with a commercial activated carbon. The results suggest that despite the high ash content of the precursor, high surface areas (614-1433 m2 g(-1)) and microporous (median pore size from 0.45 to 1.2 nm) activated carbons can be generated through chemical carbonisation and gasification. The micropore area of the activated carbon developed from chars prepared by the low temperature chemical carbonisation provides favourable adsorption sites to acid blue dye (391 mg g(-1) of carbon). The alkalinity of the carbon surface and total surface area were shown to have complementary effects in promoting the adsorption of acid blue dye. Adsorption of the anionic coloured component of the acid dye was shown to be promoted in carbon exhibiting alkaline or positively charged surfaces. This study demonstrates that activated carbons with high acid dye adsorption capacities can be prepared from high ash bagasse based on low temperature chemical carbonisation and gasification.     

稻壳基活性炭的制备及其对亚甲基蓝吸附的研究

以稻壳为原料，采用K2CO3活化法和H3P04活化法制备了比表面积为1312m^2／g和682m^2／g的活性炭，通过扫描电子显微镜（SEM）、X-射线衍射仪（XRD）对样品进行了表征，并将孔隙发达的活性炭样品用于对亚甲基蓝的吸附，结果表明，K2CO3活化法制备的活性炭样品具有更多的微孔结构；随着亚甲基蓝溶液初始浓度的增加、活性炭吸附时间的延长，亚甲基蓝的去除率呈现逐渐降低和逐渐增大的变化规律，当pH值为6时，活性炭对亚甲基蓝的吸附效果最佳；稻壳基活性炭对亚甲基蓝的吸附等温线符合Langmuir模型，Qm最高可达476．2mg／g；热力学参数△G^0△H^0和△S^0均为负值，表明稻壳基活性炭对亚甲基蓝的吸附是一个自发的放热反应。     

“氧化镁/活性炭”新型吸附剂的制备及其对Cr（Ⅵ）的吸附研究

以氯化镁和造纸草浆黑液为原料,采用物理活化法制得＂氧化镁/活性炭＂新型吸附剂,其比表面积（BET）为388.96 m2/g、总孔容积为0.40 mL/g。测定了这种吸附剂对水中Cr（Ⅵ）的吸附性能,考察了吸附时间、pH值、吸附剂投加量、初始浓度等因素对Cr（VI）的吸附量和脱除率的影响,研究所得吸附水溶液中Cr（Ⅵ）的最佳条件为：吸附时间为120min,吸附剂投加量为2 g/L,pH值为2。＂氧化镁/活性炭＂新型吸附剂对Cr（Ⅵ）的吸附过程符合Freundlich等温式。     

Production of Activated Carbons from Pyrolysis of Waste Tires Impregnated with Potassium Hydroxide

ABSTRACT

Activated carbons were produced from waste tires using a chemical activation method. The carbon production process consisted of potassium hydroxide (KOH) impregnation followed by pyrolysis in N₂ at 600-900 °C for 0-2 hr. The activation method can produce carbons with a surface area (SA) and total pore volume as high as 470 m²/g and 0.57 cm³/g, respectively. The influence of different parameters during chemical activation, such as pyrolysis temperature, holding time, and KOH/tire ratio, on the carbon yield and the surface characteristics was explored, and the optimum preparation conditions were recommended. The pore volume of the resulting carbons generally increases with the extent of carbon gasified by KOH and its derivatives, whereas the SA increases with degree of gasification to reach a maximum value, and then decreases upon further gasification.