利用含铝废盐酸制备聚合氯化铝

以某医药企业产生的含铝废盐酸为原料制备了液体聚合氯化铝(PAC)。确定了适宜的有机物去除方法和碱化剂,考察了碱化剂投加量、废盐酸铝离子含量等合成条件对PAC产品指标的影响,并比较了自制PAC和市售PAC对该企业污水站二沉池出水的混凝效果。实验结果表明:采用活性炭吸附法去除废盐酸中有机物,选择固体Ca O作为碱化剂,在活性炭投加量1‰(w)、吸附时间1 h、铝离子含量9.5%(w,以Al_2O_3计)、CaO投加量80 g/L、反应时间24 h的条件下,制备的液体PAC达到行业标准HG/T 2677—2017《工业聚氯化铝》中的Ⅲ类标准;自制PAC对废水COD和SS的去除率均优于市售PAC,不仅可替代其使用,还可外售产生经济效益。     

用累托石吸附处理含铁(Ⅲ)废水

用累托石作吸附剂处理有色金属厂冶炼过程中产生的含Fe(Ⅲ)废水。在废水pH为7．5～8．5、反应时间为30min、累托石投加量为12g／L的条件下,Fe(Ⅲ)质量浓度可由5mg／t．降到0．08mg／L,Fe(Ⅲ)的去除率最高为98．4％,外排废水符合GB8978--1996一级标准。对Fe(Ⅲ)进行等温吸附实验,其等温吸附曲线符合Langmuir模型,其吸附机理主要是吸附作用和沉淀作用。     

Comparison of different liquid anaerobic digestion effluents as inocula and nitrogen sources for solid-state batch anaerobic digestion of corn stover

Effluents from three liquid anaerobic digesters, fed with municipal sewage sludge, food waste, or dairy waste, were evaluated as inocula and nitrogen sources for solid-state batch anaerobic digestion of corn stover in mesophilic reactors. Three feedstock-to-effluent (F/E) ratios (i.e., 2, 4, and 6) were tested for each effluent. At an F/E ratio of 2, the reactor inoculated by dairy waste effluent achieved the highest methane yield of 238.5 L/kgVS_feed, while at an F/E ratio of 4, the reactor inoculated by food waste effluent achieved the highest methane yield of 199.6 L/kgVS_feed. The microbial population and chemical composition of the three effluents were substantially different. Food waste effluent had the largest population of acetoclastic methanogens, while dairy waste effluent had the largest populations of cellulolytic and xylanolytic bacteria. Dairy waste also had the highest C/N ratio of 8.5 and the highest alkalinity of 19.3 g CaCO₃/kg. The performance of solid-state batch anaerobic digestion reactors was closely related to the microbial status in the liquid anaerobic digestion effluents.     

Synthesis of Gum Acacia Capped Polyaniline-Based Nanocomposite Hydrogel for the Removal of Methylene Blue Dye

In this research work, a novel gum acacia capped polyaniline-based nanocomposite hydrogel (GPA NCHs) was developed and evaluated for the adsorptive removal of cationic methylene blue dye (MB) from aqueous solutions. Firstly, Gum acacia (GA) capped Polyaniline (PANI) dispersion was synthesized by using dispersion polymerization. Then, a water-swellable hydrogel network consisting of GA-PANI and acrylamide (AM) was obtained by using N,N′ -methylene-bisacrylamide (MBA) as a cross-linker, and ammonium persulphate/N,N,N′,N′-tetramethylethylenediamine (APS/TMEDA) as an initiating system. The developed materials were characterized by UV–visible, FTIR, XRD, SEM–EDX and TEM techniques. The microscopy studies revealed that GA-PANI nanoparticles have a granular morphological surface with an average size of?~?40–100 nm. Removal of MB dye from aqueous system was performed by adsorption studies in batch equilibrium mode with different dosage of GA-PANI, MB concentration, pH and temperatures. The adsorption data revealed that the absorption capacity of GPA NCHs highly depends on the dosage of GA-PANI, pH and concentration of the MB dye. The maximum percentage of MB removal onto GPA 1.0 NCHs was found to be 89% at pH 10 with a dye concentration of 10 mg L^?1. The equilibrium adsorption data were also analyzed by different models to understand the adsorption process. The results revealed that the adsorption process followed the pseudo-second-order kinetics and it fit well in Langmuir and Freundlich adsorption isotherms with a maximum adsorption capacity of 35.41 mg g^?1. These studies demonstrate that the GPA NCHs could be a promising adsorbent material for the removal of MB dye from contaminated aqueous systems.

     

Poultry litter-based activated carbon for removing heavy metal ions in water

Utilization of poultry litter as a precursor material to manufacture activated carbon for treating heavy metal-contaminated water is a value-added strategy for recycling the organic waste. Batch adsorption experiments were conducted to investigate kinetics, isotherms, and capacity of poultry litter-based activated carbon for removing heavy metal ions in water. It was revealed that poultry litter-based activated carbon possessed significantly higher adsorption affinity and capacity for heavy metals than commercial activated carbons derived from bituminous coal and coconut shell. Adsorption of metal ions onto poultry litter-based carbon was rapid and followed Sigmoidal Chapman patterns as a function of contact time. Adsorption isotherms could be described by different models such as Langmuir and Freundlich equations, depending on the metal species and the coexistence of other metal ions. Potentially 404 mmol of Cu²⁺, 945 mmol of Pb²⁺, 236 mmol of Zn²⁺, and 250–300 mmol of Cd²⁺ would be adsorbed per kg of poultry litter-derived activated carbon. Releases of nutrients and metal ions from litter-derived carbon did not pose secondary water contamination risks. The study suggests that poultry litter can be utilized as a precursor material for economically manufacturing granular activated carbon that is to be used in wastewater treatment for removing heavy metals.     

Effective Removing of Remazol Black B by the Polyacrylamide Cryogels Modified with Polyethyleneimine

In this study, modified polyacrylamide (PAAm) cryogels with high dye holding capacity were synthesized with an easily and cheaply process and adsorption of Remazol Black B (RBB) with the synthesized materials was investigated. Firstly, PAAm cryogels were synthesized with free radical cryo-copolymerization method and they were modified with Hofmann reaction to form amine groups in the structure of the cyrogels. Then, to increase the removal efficiency of cryogels, polyethylenimine (PEI) molecules were crosslinked onto the cryogels via NH₂ groups present in the PAAm gels modified by the Hofmann reaction. The original and modified cryogels were characterized with fourier transformed infrared spectroscopy, ¹³C nuclear magnetic resonance spectroscopy, scanning electron microscopy and thermogravimetric analysis. The point of zero charge (pH_pzc) of the modified cryogels was found to be 7.13 and RBB removing capabilities of PEI-modified PAAm cryogels were investigated at pH between 2 and 7. In addition, the adsorption treatments were performed at different process time, incubation temperature, initial dye concentration and adsorbent amount to find maximum removal capacity of the adsorbent. The modified cryogels adsorbed maximum amount of RBB at pH 2 and the sorption process reached equilibrium in 6 h. It was observed that the adsorption efficiency did not change much with the increase in temperature. The maximum RBB removal capacity of the modified cyrogels was determined to be 201 mg/g when the initial RBB concentration was 200 mg/L, treatment time was 6 h at pH 2. Moreover, the adsorption of RBB dye with the modified cryogels takes place with a second order kinetic and RBB dye adsorption data showed compliance with the Langmuir isotherm. The findings of the study expose that the obtained PEI-modified PAAm cryogels are a hopeful material for RBB removal in aqueous environment.

     

Tailoring mesoporosity of poly(furfuryl alcohol)-based activated carbons and their ability to adsorb organic compounds from water

In this work it was shown that polymers can be recycled into a promising adsorbent for organic dyes and phenols waste removal. For this, a series of activated carbons (ACs) were produced from mixture of ferrocene or titanium acetylacetonate with poly(furfuryl alcohol) (PFA) by steam activation. The introduction of ferrocene as Fe precursor was found to be an efficient catalyst in mesoporosity development during carbonization and subsequent steam activation at 850 °C, whereas the polymer based only and titanium-doped ACs are typically microporous. The porous structure parameters were determined from nitrogen adsorption isotherms measured at 77 K. Scanning electron microscopy was applied to monitor the metal distribution of metal-loaded char and the surface morphology of activated carbons. The adsorption capacity was found to be dependent mainly on pore size distribution. In the case of phenol adsorption, the adsorption was defined by volume of pore with size 0.8–1.4 nm; whereas, for Congo red best fit was observed for volume of pore with size 2–5 nm.

     

The BATINTREC process for reclaiming used batteries

The Integrated Battery Recycling (BATINTREC) process is an innovative technology for the recycling of used batteries and electronic waste, which combines vacuum metallurgical reprocessing and a ferrite synthesis process. Vacuum metallurgical reprocessing can be used to reclaim the mercury (Hg) in the dry batteries and the cadmium (Cd) in the Ni-Cd batteries. The ferrite synthesis process reclaims the other heavy metals by synthesizing ferrite in a liquid phase. Mixtures of manganese oxide and carbon black are also produced in the ferrite synthesis process. The effluent from the process is recycled, thus significantly minimizing its discharge. The heavy metal contents of the effluent could meet the Integrated Wastewater Discharge Standard of China if the ratio of the crushed battery scrap and powder to FeSO4.7H2O is set at 1:6. This process could not only stabilize the heavy metals, but also recover useful resource from the waste.     

Synthesis,Characterization and Application of α, β, and γ Cyclodextrin-Conjugated Graphene Oxide for Removing Cadmium Ions from Aqueous Media

In this study, a novel and facile route for the synthesis of cyclodextrin-conjugated graphene oxide (CDs–GO) nanocomposites by esterification reaction in the presence of EDC/DMAP as catalyst, was developed. The formation of CDs–GO was successfully approved by FT-IR, SEM, TEM, TGA and BET analyses. Then competitive adsorption capacity of cadmium ion by CDs–GO composites and the impact of different empirical parameters like contact time, initial metal ion concentration, and initial pH on the adsorption process were studied. The results showed that β-CD–GO at pH 7 is suitable for removing Cd(II) with 90?% removal efficiency. Also, the adsorption capacity experiment at constant concentration of 50 ppm of Cd(II) showed that more than 50?% of Cd(II) ions could be adsorbed by γ-CD–GO reaching an equilibrium within 2 h. Therefore, the γ-CD–GO and α-CD–GO showed high adsorption capacity toward Cd²⁺ (222.22 mg/g) which were pointedly more than that of β-CD–GO (208.33 mg/g). Furthermore, adsorption kinetics, isotherm studies, and thermodynamic analyses were evaluated. The adsorption data exhibited excellent fit to the pseudo-second-order (R²?>?0.99) and Freundlich isotherm models.

     

Selection of adsorbents for treatment of leachate: batch studies of simultaneous adsorption of heavy metals

The simultaneous adsorption of copper (Cu), cadmium (Cd), nickel (Ni), and lead (Pb) ions from spiked deionized water and spiked leachate onto natural materials (peat A and B), by-product or waste materials (carbon-containing ash, paper pellets, pine bark, and semi-coke), and synthetic materials (based on urea-formaldehyde resins, called blue and red adsorbents) or mixtures thereof was investigated. The adsorbents that gave the highest metal removal efficiencies were peat A, a mixture of peat B and carbon-containing ash, and a mixture of peat A and blue. At an initial concentration of 5 mg/l for each metal, the removal of each species of metal ion from spiked water and spiked leachate solutions was very good (>90%) and good (>75%), respectively. When the initial concentration of each metal in the solutions was twenty times higher (100 mg/l), there was a noticeable decrease in the removal efficiency of Cu²⁺, Cd²⁺, and Ni²⁺, but not of Pb²⁺. Langmuir monolayer adsorption capacities, q_m, on peat A were found to be 0.57, 0.37, and 0.36 mmol/g for Pb²⁺, Cd²⁺, and Ni²⁺, respectively. The order of metal adsorption capacity on peat A was the same in the case of competitive multimetal adsorption conditions as it was for single-element adsorption, namely Pb²⁺ > Cd²⁺ ≥ Ni²⁺. The results show that peat alone (an inexpensive adsorbent) is a good adsorbent for heavy metal ions.     

Electro-dissolution of metal scrap anodes for nickel ion removal from metal finishing effluent

This contribution reports a novel and cost efficient strategy for nickel ion removal from metal finishing effluents by electro-dissolution of scrap aluminium and iron sacrificial anodes. Electro-coagulation of effluent was carried out at 30 mA/cm² current density for 60 min. The nickel ion concentration of electroplating effluent was analysed by Atomic Absorption Spectroscopy. SEM images of iron and aluminium scrap anodes were critically analysed. Parameters such as heavy metal removal, anode dissolution rate with respect to heavy metal removal, reaction kinetics and cost estimation have been elaborately studied. Electro-coagulation at 30 mA/cm² for 60 min using iron and aluminium scrap anodes resulted in 95.9 and 94.1 % nickel ion reduction, respectively, with 0.0094 and 0.0053 g/ppm dissolution rates. The energy consumption for scrap aluminium and iron anodes was 0.0547 kWh/L. Loose internal bonding and spongy surface morphology of used metal scrap render high porosity and active surface area, enhancing reaction rate. Low cost and ready availability of waste scrap makes the process of electro-coagulation economically viable. Thus, the findings from this contribution point decisively at the superiority of waste metal scrap-based anodes for economic and environmentally sustainable heavy metal ion removal from metal finishing effluent.     

Preparation and performance of arsenate (V) adsorbents derived from concrete wastes

Solid adsorbent materials, prepared from waste cement powder and concrete sludge were assessed for removal of arsenic in the form of arsenic (As(V)) from water. All the materials exhibited arsenic removal capacity when added to distilled water containing 10–700 mg/L arsenic. The arsenic removal isotherms were expressed by the Langmuir type equations, and the highest removal capacity was observed for the adsorbent prepared from concrete sludge with heat treatment at 105 °C, the maximum removal capacity being 175 mg-As(V)/g. Based on changes in arsenic and calcium ion concentrations, and solution pH, the removal mechanism for arsenic was considered to involve the precipitation of calcium arsenate, Ca₃(AsO₄)₂. The enhanced removal of arsenic for the adsorbent prepared from concrete sludge with heat treatment was thought to reflect ion exchange by ettringite. The prepared adsorbents, derived from waste cement and concrete using simple procedures, may offer a cost effective approach for arsenic removal and clean-up of contaminated waters, especially in developing countries.     

Design parameters for fixed bed reactors of activated carbon developed from fertilizer waste for the removal of some heavy metal ions

Activated carbon, developed from fertilizer waste, has been used for the removal of Hg²⁺, Cr⁶⁺, Pb²⁺, and Cu²⁺. Mass transfer kinetic approach has been successfully applied for the determination of various parameters necessary for designing a fixed-bed absorber. Parameters selected are the length of the (PAZ) primary adsorption zone (δ), total time involved for the establishment of primary adsorption zone (t_x), mass rate of flow to the absorber (F_m), time for primary adsorption zone to move down its length (t_δ), amount of adsorbate adsorbed in PAZ from breakpoint to exhaustion (M_s), fractional capacity (f), time of initial formation of PAZ (t_f) and per cent saturation of column at break point. Chemical regeneration has been achieved with 1 M HNO₃.     

催化裂化钠碱脱硫液中钙镁离子的去除

研究了化学沉淀法和氨基膦酸型螯合树脂吸附法对催化裂化钠碱脱硫液中Ca~(2+)和Mg~(2+)的去除效果。实验结果表明:NaOH沉淀法可有效去除钠碱脱硫液中的Mg~(2+),当溶液pH为12、反应时间为15 min时,Mg~(2+)去除率达91.6%;NaOH-Na_2CO_3联合沉淀法无法去除钠碱脱硫液中的Ca~(2+);经过NaOH溶液有效除Mg~(2+)后的脱硫液再采用氨基膦酸型螯合树脂吸附柱去除其中的Ca~(2+)和Mg~(2+),可使出水硬度小于2 mg/L。提高进水pH、降低进水流量、降低进水硬度均可提高单位体积树脂的处理水量。     

离子交换树脂处理三乙胺废水

采用离子交换树脂对废水中三乙胺进行吸附。探讨了静态及动态吸附三乙胺的影响因素,考察了树脂的脱附条件及其吸附稳定性。实验结果表明:RX01型树脂对三乙胺的吸附性能优于HD-81型和D155型树脂;在三乙胺初始质量浓度为1 500 mg/L、初始pH为11.5、吸附时间为2 h、吸附温度为298 K的静态吸附条件下,三乙胺去除率为96.3%,饱和吸附量为145 mg/g,等浓度条件下阳离子影响的大小顺序为Ca~(2+)Mg~(2+)K~(+)Na~(+);当三乙胺初始质量浓度为1 500 mg/L、废水流量为60 BV/h、动态吸附柱高径比为5.37时,穿透体积为70 BV,出水三乙胺质量浓度小于3 mg/L,三乙胺去除率高达99.5%;以2 mol/L的HCl溶液为脱附剂,脱附剂流量为1 BV/h、出水体积为4 BV时,三乙胺的脱附率达94.8%;在最优动态吸附-脱附条件下重复使用10次,树脂性能稳定。     

Heterotrophic Biological Denitrification Using Microbial Cellulose as Carbon Source

The objective of this study was to investigate the feasibility of using a microbial biopolymer produced by Acetobacter xylinum as a carbon source for heterotrophic biological denitrification. The denitrification rate, COD availability and nitrite concentration were response parameters. Under the experimental conditions, a denitrification rate of about 0.74 kg NO₃ ⁻N/m³d at 6 h retention time was achieved with microbial cellulose (MC). The reactor effluent contained significantly COD concentrations (20–86 mg/L) so it was not carbon limited, and was receiving enough carbon to facilitate the denitrification process. The maximum nitrite concentration in the effluent was found to be 0.4 mg/L. However, decreasing the retention time to 3 h significantly reduced the efficiency. It can be concluded that the MC is a suitable carbon source for nitrate removal in a heterotrophic biological denitrification process.     

Utilization of Triacetylcellulose Waste for the Production of Carbonaceous Adsorbents

Triacetylcellulose(TAC)-based globular activated carbons having the adsorption capacity comparable with commercial ones have been derived using a carbonization system developed for this purpose. The carbonization of TAC proceeds through a liquid phase causing bubbling due to the emission of the decomposition gases. The phosphorus compounds resulting from the starting material of TAC waste promote the activation reactions to produce micro-pores.     

Adsorption characteristics of Cu2+ and Zn2+ from aqueous solution using carbonized food waste

The aim of the present study was to analytically provide adsorption characteristics of Cu²⁺ and Zn²⁺ using carbonized food waste (CFW); more specifically, batch tests were conducted using various concentrations of metal ions, contact times, and initial pH levels in an attempt to understand the adsorption removal of heavy metal ions in aqueous solution at concentrations ranging between 50 and 800 mg/l. The results confirmed that the adsorption equilibrium was established within a maximum of 80 min, and the maximum concentrations for adsorption of Cu²⁺ and Zn²⁺ were 28.3 and 23.5 mg/g, respectively. These adsorption levels indicate that CFW has better performance than many other adsorbents. In experiments using different pH conditions, the applicability to acid wastewater was found to be high, and an excellent adsorption removal ratio of 75%–90% was observed under acid conditions at pH 2–4. Furthermore, as the adsorption time increased, the calcium component in the CFW began to leach into the aqueous solution and raise the pH, accordingly causing the removal of heavy metal ions partially as a result of precipitation. When our results were analyzed using the Langmuir model and the Freundlich model for isothermal adsorptivity, the activity of CFW in this study was shown to be more consistent with the former; the adsorption speed of Cu²⁺ and Zn²⁺ according to a pseudosecond-order reaction model was found to be very fast for an initial concentration of not more than 100 mg/l. In a test in which an attempt was made to compare adsorption capacity values obtained from the experiments in this study with the aforementioned three models, the pseudosecond-order reaction model was found to provide results closest to the actual values.     

Treating landfill gas hydrogen sulphide with mineral wool waste (MWW) and rod mill waste (RMW)

Hydrogen sulphide (H₂S) gas is a major odorant at municipal landfills. The gas can be generated from different waste fractions, for example demolition waste containing gypsum based plaster board. The removal of H₂S from landfill gas was investigated by filtering it through mineral wool waste products. The flow of gas varied from 0.3 l/min to 3.0 l/min. The gas was typical for landfill gas with a mean H₂S concentration of ca. 4500 ppm. The results show that the sulphide gas can effectively be removed by mineral wool waste products. The ratios of the estimated potential for sulphide precipitation were 19:1 for rod mill waste (RMW) and mineral wool waste (MWW). A filter consisting of a mixture of MWW and RMW, with a vertical perforated gas tube through the center of filter material and with a downward gas flow, removed 98% of the sulfide gas over a period of 80 days. A downward gas flow was more efficient in contacting the filter materials. Mineral wool waste products are effective in removing hydrogen sulphide from landfill gas given an adequate contact time and water content in the filter material. Based on the estimated sulphide removal potential of mineral wool and rod mill waste of 14 g/kg and 261 g/kg, and assuming an average sulphide gas concentration of 4500 ppm, the removal capacity in the filter materials has been estimated to last between 11 and 308 days. At the studied location the experimental gas flow was 100 times less than the actual gas flow. We believe that the system described here can be upscaled in order to treat this gas flow.     

The adsorption characteristics of heavy metals by various particle sizes of MSWI bottom ash

The incineration rate of municipal solid waste (MSW) has been increased because of difficulty in securing a proper disposal site for MSW in Korea. The advantage of incineration is reduction of the volume of waste; however, significant amounts of bottom ash and fly ash were generated in the incineration process. Their treatment has attracted growing interest because of the potential toxicity of hazardous heavy metals. Generally, heavy metals are less released from bottom ash than from fly ash. In this study the adsorption characteristics of heavy metals were investigated using various particle sizes of MSWI bottom ash. Since bottom ash has a broad particle size distribution, it was sieved to size classes of +20, -20, -48, -80, -100 mesh. Cation exchange capacity (CEC) was analyzed by the ammonium acetate method to evaluate the potential as an adsorbent. The CEC values and surface areas increase as the range of particle size becomes finer. The adsorption experiment was conducted using synthetic (Cu and Ni) and plating rinse water as a function of reaction time (10-180 min), liquid/solid ratio (2-100) and particle size (+20 to -100 mesh), respectively. The adsorption rate increased with decreasing particle size and with increasing liquid/solid ratio; however, the removal efficiency of Cu was higher than that of Ni. In the case of plating rinse water, the adsorption rate decreased sharply at high liquid/solid ratio, and it showed over 80% of adsorption rates for Cu and Ni at an initial pH of 3.