Recycling of WEEE: characterization of spent printed circuit boards from mobile phones and computers

This paper presents a comparison between printed circuit boards from computers and mobile phones. Since printed circuits boards are becoming more complex and smaller, the amount of materials is constantly changing. The main objective of this work was to characterize spent printed circuit boards from computers and mobile phones applying mineral processing technique to separate the metal, ceramic, and polymer fractions. The processing was performed by comminution in a hammer mill, followed by particle size analysis, and by magnetic and electrostatic separation. Aqua regia leaching, loss-on-ignition and chemical analysis (inductively coupled plasma atomic emission spectroscopy - ICP-OES) were carried out to determine the composition of printed circuit boards and the metal rich fraction. The composition of the studied mobile phones printed circuit boards (PCB-MP) was 63 wt.% metals; 24 wt.% ceramics and 13 wt.% polymers; and of the printed circuit boards from studied personal computers (PCB-PC) was 45 wt.% metals; 27 wt.% polymers and ceramics 28 wt.% ceramics. The chemical analysis showed that copper concentration in printed circuit boards from personal computers was 20 wt.% and in printed circuit boards from mobile phones was 34.5 wt.%. According to the characteristics of each type of printed circuit board, the recovery of precious metals may be the main goal of the recycling process of printed circuit boards from personal computers and the recovery of copper should be the main goal of the recycling process of printed circuit boards from mobile phones. Hence, these printed circuit boards would not be mixed prior treatment. The results of this paper show that copper concentration is increasing in mobile phones and remaining constant in personal computers.     

Techniques to separate metal from waste printed circuit boards from discarded personal computers

Waste printed circuit boards contain valuable metals such as Au, Pd, Ag, and Cu that can be reutilized and harmful elements such as Pb, Br, and Cr that must be removed from the viewpoint of environmental conservation. In this research, we examined a method that separates the materials from printed circuit boards contained in discarded personal computers. After cutting the printed circuit boards to a size of 20 × 20 mm, they were heated at 873 K under an Ar atmosphere to remove organic resins containing elements such as C, H, and N. After heat treatment, the printed circuit boards were crushed using a planetary ball mill and the pulverized powders were filtered. The fraction with a granularity of greater than 250 μm was separated into magnetic and nonmagnetic materials by a magnetic field. Because the fraction with a granularity of less than 250 μm contained 39 mass% of C, it was heated at 1273 K in an atmosphere of 95% Ar and 5% O₂ to allow carbon combustion to take place, followed by metal reduction processing at the same temperature in an atmosphere of 97% Ar and 3% H₂. The basicity of the resulting powder was adjusted and the powder was heated at 1773 K under an Ar atmosphere. The proposed method separated the slag and metal, and 80% of the valuable metals contained in printed circuit boards could be collected.     

Enhancement of the recycling of waste Ni-Cd and Ni-MH batteries by mechanical treatment

A serious environmental problem was presented by waste batteries resulting from lack of relevant regulations and effective recycling technologies in China. The present work considered the enhancement of waste Ni-Cd and Ni-MH batteries recycling by mechanical treatment. In the process of characterization, two types of waste batteries (Ni-Cd and Ni-MH batteries) were selected and their components were characterized in relation to their elemental chemical compositions. In the process of mechanical separation and recycling, waste Ni-Cd and Ni-MH batteries were processed by a recycling technology without a negative impact on the environment. The technology contained mechanical crushing, size classification, gravity separation, and magnetic separation. The results obtained demonstrated that: (1) Mechanical crushing was an effective process to strip the metallic parts from separators and pastes. High liberation efficiency of the metallic parts from separators and pastes was attained in the crushing process until the fractions reached particle sizes smaller than 2 mm. (2) The classified materials mainly consisted of the fractions with the size of particles between 0.5 and 2 mm after size classification. (3) The metallic concentrates of the samples were improved from around 75% to 90% by gravity separation. More than 90% of the metallic materials were separated into heavy fractions when the particle sizes were larger than 0.5 mm. (4) The size of particles between 0.5 and 2 mm and the rotational speed of the separator between 30 and 60 rpm were suitable for magnetic separation during industrial application, with the recycling efficiency exceeding 95%.     

Utilization of magnetic and electrostatic separation in the recycling of printed circuit boards scrap

The progress of the technology is directly related to the growth of production and consumption of electrical/electronics equipment, especially of personal computers. This type of equipment has a relatively short average lifetime, 2-3 years. The amount of defective or obsolete equipment has been increasing substantially; consequently its disposition and/or recycling should be studied. In this work, printed circuit boards, which are used in personal computers, were studied in order to recover the metals in the circuit boards through mechanical processing, such as crushing, screening, as well as magnetic and electrostatic separation. The results obtained demonstrate the feasibility of using these processes to separate metal fractions from polymers and ceramics, and that it is possible to obtain a fraction concentrated in metals containing more than 50% on average of copper, 24% of tin and 8% of lead.     

Liberation characteristic and physical separation of printed circuit board (PCB)

Recycling of printed circuit board (PCB) is an important subject and to which increasing attention is paid, both in treatment of waste as well as recovery of valuable material terms. Precede physical and mechanical method, a good liberation is the premise to further separation. In this study, two-step crushing process is employed, and standard sieve is applied to screen crushed material to different size fractions, moreover, the liberation situation and particles shape in different size are observed. Then metal of the PCB is separated by physical methods, including pneumatic separation, electrostatic separation and magnetic separation, and major metal contents are characterized by inductively coupled plasma emission spectrometry (ICP-AES). Results show that the metal and nonmetal particles of PCB are dissociated completely under the crush size 0.6mm; metal is mainly enriched in the four size fractions between 0.15 and 1.25 mm; relatively, pneumatic separation is suitable for 0.6-0.9 mm size fraction, while the electrostatic separation is suitable for three size fractions that are 0.15-0.3mm, 0.3-0.6mm and 0.9-1.25 mm. The whole process that involves crushing, electrostatic and magnetic separation has formed a closed cycle that can return material and provide salable product.     

Printed wiring boards for mobile phones: characterization and recycling of copper

The popularization of mobile phones, combined with a technological evolution, means a large number of scrap and obsolete equipment are discarded every year, thereby causing economic losses and environmental pollution. In the present study, the printed wiring boards scrap of mobile phones were characterized in order to recycle some of the device components, using techniques of mechanical processing, hydrometallurgy and electrometallurgy. The use of the techniques of mechanical processing (milling, particle size classification, magnetic and electrostatic separation) was an efficient alternative to obtain a concentrated fraction (mainly iron in the magnetic fraction and copper in the conductive fraction) and another fraction containing polymers and ceramics. At the end of mechanical processing, a concentrated fraction of metals could be obtained with an average concentration of 60% copper. This concentrated fraction in metals was dissolved in aqua regia and sent to electrowinning to recover 92% of the dissolved copper. The obtained cathodes have a copper content above 95%, which demonstrates the technical feasibility of recovery of copper using the techniques of mechanical processing, hydrometallurgy and electrometallurgy.     

从废印制电路板元器件中分离电容器的方法

以典型废印制电路板湿法剥离得到的元器件为研究对象,通过筛分和磁选相结合的物理方法,分离其中的电容器。研究发现,筛分后电容器分布在9.5-19 mm和4.0-9.5 mm范围内,并且50%以上的元器件与电容器得到分离。9.5-19 mm范围内的元器件经过磁选,可以将强磁性的铜线绕阻类元器件分离出来,剩余元器件采用8 mm宽的条形筛进行筛分,筛上物主要为电容器,筛下物主要为芯片和引脚;4.0-9.5 mm范围内的元器件经过磁选,可以将92.93%的电容器分离出来。     

Characterization of shredded television scrap and implications for materials recovery

Characterization of TV scrap was carried out by using a variety of methods, such as chemical analysis, particle size and shape analysis, liberation degree analysis, thermogravimetric analysis, sink-float test, and IR spectrometry. A comparison of TV scrap, personal computer scrap, and printed circuit board scrap shows that the content of non-ferrous metals and precious metals in TV scrap is much lower than that in personal computer scrap or printed circuit board scrap. It is expected that recycling of TV scrap will not be cost-effective by utilizing conventional manual disassembly. The result of particle shape analysis indicates that the non-ferrous metal particles in TV scrap formed as a variety of shapes; it is much more heterogeneous than that of plastics and printed circuit boards. Furthermore, the separability of TV scrap using density-based techniques was evaluated by the sink-float test. The result demonstrates that a high recovery of copper could be obtained by using an effective gravity separation process. Identification of plastics shows that the major plastic in TV scrap is high impact polystyrene. Gravity separation of plastics may encounter some challenges in separation of plastics from TV scrap because of specific density variations.     

Pulverization of waste printed circuit boards

A new pulverization method to reduce the volume of waste printed circuit boards is reported. About 50% of printed circuit boards with integrate circuits (ICs) could be pulverized by our method in one 20-min batch, but boards without ICs could not be pulverized. By repeating the process three times, about 95% of printed circuit boards with ICs could be made into a fine powder with particles less than 106µm. A weight-drop test was also performed to examine the strength of the printed circuit boards and clarify the mechanism of pulverization. When a weight was dropped on the solder-welding side of the board ruptures occurred more easily than when the weight was dropped on the IC-mounted side. With a heavy weight, the IC was fractured more easily when the potential energy was low. Where the stress was concentrated, two types of rupture location were found on printed circuit boards with ICs. One was where the IC was connected to the printed circuit board. The other was where the surface had undulations. It also became clear that the fracture of printed circuit boards depends on the impacting weight rather than on the potential energy.     

Recovery of residual metals from − 0.5 mm non-metallic fractions in WPCBs using electrostatic separation enhanced by air classification

Journal of Material Cycles and Waste Management - Electrostatic separation is a cleaning physical method to recover metals from waste printed circuit boards (WPCBs), but it has poor separation...     

废旧电路板上残留焊锡剥离液的研制

以硝酸-磺酸型退锡剂为基础配方,研制了一种脱除废旧电路板表面残留焊锡的剥离液.该剥离液以硝酸为氧化剂,氨基磺酸为稳定剂,苯并三氮唑为铜的缓蚀剂.实验结果表明:剥离液的最佳配比为硝酸浓度3 mol/L,氨基磺酸浓度0.4 mol/L,苯并三氮唑浓度0.08 mol/L;每升剥离液可处理3.5 kg废旧电路板,处理后电路板中的铅离子含量降至100 mg/kg以下.该剥离液处理后的电路板表面的铜箔保持完好,基本没有被剥离液浸蚀.     

Evaluation of a recycling process for printed circuit board by physical separation and heat treatment

Printed circuit boards (PCBs) from discarded personal computer (PC) and hard disk drive were crushed by explosion in water or mechanical comminution in order to disintegrate the attached parts. More parts were stripped from PCB of PC, composed of epoxy resin; than from PCB of household appliance, composed of phenol resin.In an attempt to raise the copper grade of PCB by removing other components, a carbonization treatment was investigated. The crushed PCB without surface-mounted parts was carbonized under a nitrogen atmosphere at 873–1073 K. After screening, the char was classified by size into oversized pieces, undersized pieces and powder. The copper foil and glass fiber pieces were liberated and collected in undersized fraction. The copper foil was liberated easily from glass fiber by stamping treatment.As one of the mounted parts, the multi-layered ceramic capacitors (MLCCs), which contain nickel, were carbonized at 873 K. The magnetic separation is carried out at a lower magnetic field strength of 0.1 T and then at 0.8 T. In the +0.5 mm size fraction the nickel grade in magnetic product was increased from 0.16% to 6.7% and the nickel recovery is 74%.The other useful mounted parts are tantalum capacitors. The tantalum capacitors were collected from mounted parts. The tantalum-sintered bodies were separated from molded resins by heat treatment at 723–773 K in air atmosphere and screening of 0.5 mm. Silica was removed and 70% of tantalum grade was obtained after more than 823 K heating and separation.Next, the evaluation of Cu recycling in PCB is estimated. Energy consumption of new process increased and the treatment cost becomes 3 times higher comparing the conventional process, while the environmental burden of new process decreased comparing conventional process.The nickel recovery process in fine ground particles increased energy and energy cost comparing those of the conventional process. However, the environmental burden decreased than the conventional one.The process for recovering tantalum used more heat for the treatment and therefore the energy consumption increased by 50%, when comparing with conventional process. However, the market price for tantalum is very large; the profit for tantalum recovery is added. Also the environmental burden decreased by the recycling of tantalum recovery. Therefore, the tantalum recovery is very important step in the PCB recycling. If there is no tantalum, the consumed energy and treatment cost increase in the new process, though the environmental burden decreases.     

The separation of waste printed circuit board by dissolving bromine epoxy resin using organic solvent

Separation of waste printed circuit boards (WPCBs) has been a bottleneck in WPCBs resource processing. In this study, the separation of WPCBs was performed using dimethyl sulfoxide (DMSO) as a solvent. Various parameters, which included solid to liquid ratio, temperature, WPCB sizes, and time, were studied to understand the separation of WPCBs by dissolving bromine epoxy resin using DMSO. Experimental results showed that the concentration of dissolving the bromine epoxy resin increased with increasing various parameters. The optimum condition of complete separation of WPCBs was solid to liquid ratio of 1:7 and WPCB sizes of 16 mm² at 145 °C for 60 min. The used DMSO was vapored under the decompression, which obtained the regenerated DMSO and dissolved bromine epoxy resin. This clean and non-polluting technology offers a new way to separate valuable materials from WPCBs and prevent the environmental pollution of waste printed circuit boards effectively.     

Quantitative characterization of recyclable resources dismantled from waste liquid crystal display products

Currently only limited materials, such as common metals and plastics, are recovered from waste flat-panel displays, thus necessitating the development of a comprehensive recycling process. This study aims to establish a statistical database about the types and amounts of valuable resources in waste liquid crystal display (LCD) products. To obtain these data, the waste LCD products were disassembled into four components: plastics, printed circuit boards, metals, and other materials, including their panels, and the weight of each component was measured. Overall, the product weight decreased with increasing manufacturing year regardless of the product screen size; however, the decreasing rate varied from 14 to 73%. The metal weight ratios decreased significantly by 24–31%. Meanwhile, regardless of the manufacturing year, the plastic weight ratios remained almost constant at about 20%. On the other hand, the weight ratio of the other components increased by 26–46% with increasing manufacturing year suggesting that rare-earth metal recycling has become more important. These statistical analyses are expected to contribute to the development of an eco-friendly, high-efficiency dismantling/separation process that will enable higher value recycling and minimal waste disposal.     

New characterisation method of electrical and electronic equipment wastes (WEEE)

Innovative separation and beneficiation techniques of various materials encountered in electrical and electronic equipment wastes (WEEE) is a major improvement for its recycling. Mechanical separation-oriented characterisation of WEEE was conducted in an attempt to evaluate the amenability of mechanical separation processes. Properties such as liberation degree of fractions (plastics, metals ferrous and non-ferrous), which are essential for mechanical separation, are analysed by means of a grain counting approach. Two different samples from different recycling industries were characterised in this work. The first sample is a heterogeneous material containing different types of plastics, metals (ferrous and non-ferrous), printed circuit board (PCB), rubber and wood. The second sample contains a mixture of mainly plastics. It is found for the first sample that all aluminium particles are free (100%) in all investigated size fractions. Between 92% and 95% of plastics are present as free particles; however, 67% in average of ferromagnetic particles are liberated. It can be observed that only 42% of ferromagnetic particles are free in the size fraction larger than 20 mm. Particle shapes were also quantified manually particle by particle. The results show that the particle shapes as a result of shredding, turn out to be heterogeneous, thereby complicating mechanical separation processes. In addition, the separability of various materials was ascertained by a sink–float analysis and eddy current separation. The second sample was separated by automatic sensor sorting in four different products: ABS, PC–ABS, PS and rest product. The fractions were characterised by using the methodology described in this paper. The results show that the grade and liberation degree of the plastic products ABS, PC–ABS and PS are close to 100%. Sink–float separation and infrared plastic identification equipment confirms the high plastic quality. On the basis of these findings, a global separation flow sheet is proposed to improve the plastic separation of WEEE.     

废弃印刷线路板资源化处理的研究进展

介绍了当前废弃印刷线路板资源化处理的主要方法，包括湿法、火法、机械法、生物法、超临界流体法和等离子体熔炼法等。综述了各种处理方法的侧重点及利弊；提出热解法与机械法联用可较好地解决在破碎过程中所遇到的问题，具有较大优势，可作为未来大量废弃印刷线路板资源化处理工艺研究的重点。     

废弃印刷线路板中材料的资源化回收利用技术

废弃印刷线路板（WPCBs）既有污染环境的一面,又有可资源化回收利用的一面.通过机械物理法、热解、超临界流体氧化和离子液体溶解等方法对其进行分离和回收金属和非金属材料.初步分选的金属需要进一步提纯以实现高附加值.而非金属材料可以用热解法、微波处理、超临界流体技术、等离子技术等技术进行产气和能量回收,也可以通过制备建筑材料或填料和其它功能村料进行物料回收.总之,对WPCBs进行适当地处理不但可以减轻环境压力,还可以变废为宝,实现资源再生利用.     

Recovery of materials from waste printed circuit boards by vacuum pyrolysis and vacuum centrifugal separation

In this research, a two-step process consisting of vacuum pyrolysis and vacuum centrifugal separation was employed to treat waste printed circuit boards (WPCBs). Firstly, WPCBs were pyrolysed under vacuum condition at 600 °C for 30 min in a lab-scale reactor. Then, the obtained pyrolysis residue was heated under vacuum until the solder was melted, and then the molten solder was separated from the pyrolysis residue by the centrifugal force. The results of vacuum pyrolysis showed that the type-A of WPCBs (the base plates of which was made from cellulose paper reinforced phenolic resin) pyrolysed to form an average of 67.97 wt.% residue, 27.73 wt.% oil, and 4.30 wt.% gas; and pyrolysis of the type-B of WPCBs (the base plates of which was made from glass fiber reinforced epoxy resin) led to an average mass balance of 72.20 wt.% residue, 21.45 wt.% oil, and 6.35 wt.% gas. The results of vacuum centrifugal separation showed that the separation of solder was complete when the pyrolysis residue was heated at 400 °C, and the rotating drum was rotated at 1200 rpm for 10 min. The pyrolysis oil and gas can be used as fuel or chemical feedstock after treatment. The pyrolysis residue after solder separation contained various metals, glass fibers and other inorganic materials, which could be recycled for further processing. The recovered solder can be reused directly and it can also be a good resource of lead and tin for refining.     

A new strain for recovering precious metals from waste printed circuit boards

A new strain, Pseudomonas Chlororaphis (PC), was found for dissolving gold, silver, and copper from the metallic particles of crushed waste printed circuit boards (PCBs). The optimized conditions that greatly improved the ability of producing CN^? (for dissolving metals) were obtained. Dissolving experiments of pure gold, silver, and copper showed that the metals could be changed into Au⁺, Ag⁺, and Cu²⁺. PC cells and their secreta would adsorb metallic ions. Meanwhile, metallic ions destroyed the growth of PC. Dissolving experiments of metallic particles from crushed waste PCBs were performed by PC. The results indicated that 8.2% of the gold, 12.1% silver, and 52.3% copper were dissolved into solution. This paper contributed significance information to recovering precious metals from waste PCBs by bioleaching.     

Evaluation of Aspergillus niger and Penicillium simplicissimum for their ability to leach Zn–Ni–Cu from waste mobile phone printed circuit boards

Journal of Material Cycles and Waste Management - In this research, Zn, Ni, and Cu recovery from mobile phone printed circuit boards was investigated. The initial pH and pulp density using...